Search Documents

Sustainable development is at odds with reality in the minerals industry. Increasing world population and aspirations are leading to increased energy and mineral consumption. Non-renewable fossil fuels are being exploited at a much faster rate than they are being discovered. Mineral reserves are diminishing and of lower grade. Despite recycling, many of the economic reserves of the rarer metals on which technological society has come to depend are being depleted, and many of the bulk metals are being exploited at ever increasing rates. And yet, mining continues, with a long-term downtrend in commodity prices, matched by more efficient mining and processing. Will society turn to a low carbon economy before fossil fuels are depleted? Will prices come to better reflect the full cost of mineral production? Will technology save us, or is it at the root of the problem? The key drivers continue to be an ever increasing aspirational population and the law of supply and demand, rather than sustainability considerations. The paper illustrates this with examples of worldwide and Australian data.

Jan 1, 2011

By K. Neumann

"INTRODUCTION For many automation and safety tasks in open cut and underground scenarios it is crucial to have highly reliable distance measurements at hand. These measurements can for instance be used to obtain the exact position of a machine in one-, two- or even three dimensions. Research and development has shown interest in the ultra-wide-band technology (UWB) in recent years. While for this technology short range, high speed data transfer is the current main research focus, the technology can also be used for highly accurate ranging applications. Due to the use of a very wide frequency band, it is robust against disturbances of many types (e.g. EMC, rain, dust etc.) and is therefore attractive for the use in mining applications. The wide frequency band also offers benefits for ranging applications. Especially in environments with strong multipath problems such as in underground mines it is possible to focus on the dominant signal propagation path, thus increasing the reliability of the measurements. [1] State-of-the-art UWB ranging equipment claims precision within the range of a couple of centimeters and working ranges of more than hundred meters. At the Institute for Mining and Metallurgical Machinery (IMR) at RWTH Aachen University in Germany a modern UWB system was examined in several laboratory and real life tests to examine the feasibility of UWB bases ranging equipment in mining applications. UWB TECHNOLOGY The term ultra-wide-band denotes radio systems that use an ultra-wide frequency band. A common definition for UWB radio systems is that it needs to work on a frequency bandwidth of more than 500 MHz or a bandwidth equal to 20% or more of the center frequency [1]. Due to the ultra-wide frequency bandwidth UWB systems overlap the frequency spectrum of narrow band radio technologies like Wi-Fi, Bluetooth and other mobile communication systems which use a defined carrier frequency onto which information is modulated on (e.g. by using frequency or phase modulation). In order to not conflict with these other radio applications, it needs to be ascertained that the transmission power of a UWB system on a given frequency is so low that narrow band systems are not affected by it. As opposed to this only a small fraction of the UWB system’s bandwidth is affected by the narrow band system. The unaffected remaining bandwidth is sufficient to reconstruct the original signal, even if additional noise is present. Figure 1 shows the power spectral densities of popular radio standards [6], [7], [8]. A significant driver of research and development of UWB systems has been wireless high bandwidth communication. Using an ultra-wide frequency band is highly desirable here, as the channel capacity is dependent on the bandwidth. So far systems have been realized especially for short distances (e.g. wireless USB or Wireless HDMI) but beyond that, communication systems for long distances (several kilometers) are possible [2]. Advances in semiconductor technology led to a reduction in power dissipation of such systems. This enabled higher integration levels which in turn facilitated smaller solution sizes for space constrained applications [3]. Nowadays, UWB is also used for high-precision ranging applications [4], [5]."

Jan 1, 2015

By G. Van Weert

Oxygen transfer from dispersed air in agitated slurries represents an important unit operation in the minerals processing industry. Gold leaching, iron precipitation and especially bio-oxidation come readily to mind. However, little engineering information is available on the variations between impeller types on such O2 transfer. Engineering literature on the subject, i.e. information which relates slurry density and energy input to O2 transfer, is reviewed and compared to current experimental work. The latter was carried out with minus 50 micron sand/water slurries in a 64 I laboratory tank of standard proportions, equipped with a variable speed drive with torque meter. A standard Rushton turbine and a specifically sized A315 were compared. Results confirm an increasing impairment of O2 transfer with increasing slurry density for both impellers. The volumetric mass transfer coefficient, k,a, in a 10 vol. % slurry shows a decrease of 30% compared to the k,a in water. At 20 vol. % sand this decrease is near 50 %, depending somewhat on superficial gas velocities. Power efficiency, i.e. the kg O2/kWh, decreases about 25 % more rapidly for the Rushton turbine than for the A315 with the addition of sand. However, for equivalent O2 transfer the Rushton turbine was more efficient in this work. Experimental results are presented and their significance for slurry bio-oxidation discussed.

Jan 1, 1996

By Gary Brendel

India produces about 70 Mt/a (77million stpy) of coal ash (fly ash and bottom ash) from burning about 200 Mt/a (220 million stpy) of coal for electric power generation. The average ash content is 35%. In contrast, the United States produces about 70 Mt/a (77 million stpy) of coal ash from burning 800 Mt/a (880million stpy) of coal for power generation. Its average ash content is less than 10%. In 1998, GAI Consultants Inc.(GAI) embarked on a federally funded, multiyear project to assist the government of India in solving its growing coal-ash management problem.

Jan 1, 1999

By Yinan Zhang, Y. Luo

Most of the reported coal spontaneous combustion events occur in surface and underground mines where low rank coals (i.e., subbituminous and lower for this particular studies) are extracted indicating their high propensities for spontaneous combustion. Low rank coals have high moisture content (15 to 45%) and are capable of absorbing more moisture in dried condition. However, it is hard to induce the initial stage of self-heating process for the low rank coal using the current laboratory R70 testing method — a method widely used in the coal industry. Like a sponge, dry low rank coals can absorb water vapor in the air while the heat contained in the moist air is transferred to coal and served as the required activation energy to initiate the coal self-heating process. In order to prove this theorem and quantify the effects, the R70 adiabatic oxidation testing method has been improved to introduce a controlled moist flow into the coal reaction vessel. Tests using the new method and its setup on low rank coals showed that the initial self-heating process of coal sample can be greatly accelerated by the added water vapor — impossible with the regular R70 method. Once the self-heating is sustained, the removal of air moisture can further accelerate the process.

Sep 17, 2021

By John Hardy

The performance of five dense-medium washers was evaluated in four preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation. The secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The sharpness-of-separation was excellent for all four primary separations and the secondary separation.

Jan 1, 1966

By Yuanbo Zhang, Yikang Tu, Zijian Su

Stainless steel swarf is a typical by-product produced from stainless steel processing, which contains a significant level of valuable metals, such as iron, chrome, and nickel. About 1 million tons of stainless steel swarf are generated in China annually, but as mixed with impurities such as Al and Si, stainless steel swarf is not suitable to be directly smelted into stainless steel through refining process. In this study, stainless steel swarf was applied as a strengthening agent during limonitic laterite sintering process. The effects of adding stainless steel swarf on green bed permeability, the yield and quality indexes of the sinters, and the microstructure of the sinters were evaluated systematically. The results showed that the concentrated distribution degree of granules and green bed permeability were improved after adding stainless steel swarf. As the additional amount of stainless steel swarf increased from 0 to 3%, the tumble index and yield of the sinters rose from 50.07 to 54.69% and from 62.04 to 67.35%, respectively. The addition of stainless steel swarf would not change the phase compositions, and had little adverse impact on the metallurgical properties of the limonitic laterite sinters.

Aug 23, 2023

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, CWP and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by particle composition, size distributions, shapes). This preliminary study sought to characterize dust from an underground coal mine in Central Appalachia using scanning electron microscopy with energy dispersive x-ray (SEM-EDX). Respirable dust samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate total respirable dust concentrations during sampling. Here we report initial results of this work, and discuss advantages and challenges of particle-level characterization of mine dusts in terms of occupational health research.

Feb 23, 2014

By N. Moelans, I. Bellemans, K. Verbeken

Metallic droplets can remain attached to solid particles within liquid slags, resulting in production losses in several movement of solid particles in the liquid slag in a system, considering the attachment of liquid metal droplets to solid slag and on the resulting microstructures is investigated as a function of the velocity of the particles. For all wetting For the amount of metal attached to the particle, a clear trade-off was found between the speed of motion of the solid particle and the wetting regime.

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal, and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely. In this study, the failure energy partitioning of Nugget Sandstone specimens is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrate a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining-induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

Jul 1, 2020

By Hernan Fernandez, Khalid Saif F S Al- Khayareen, Volkan Salepciler, Jacek B. Stypulkowski

Wakrah and Wukair Drainage Tunnel, WWDT is 13 km long with a 4.5 m ID sewer water tunnel about 50 to 60 m below ground surface. Integral to the project are several adits with provisions for future connections as well as four work shafts, four intermediate access shafts, ancillary hydraulic structures, and an Odor Control Facility. The shaft depths range from 50 to 60 m. The project is constructed in aggressive ground with aggressive ground water. The construction activities require years of pumping and disposal of the ground water during tunneling operations as well as construction of permanent structures in shafts. Grouting of the corrosive rock mass in corrosive groundwater for the WWDT has been described in detail.

Jun 23, 2024

By M. E. Rossi

This paper discusses the use of Conditional Simulation (CS) models to provide mill feed grade profiles for different time periods. The conventional approach of classifying block estimates as ore or waste generally does not adequately represent dilution, lost ore and the anticipated grade control data, including variability of mill feed from the pit and possible stockpiles. The detailed simulation of grade control practices can be done, but at the Pre- or Feasibility stage of the project may be impractical, since drawing dig limits on multiple benches is tedious and time consuming. Using the Feasibility Grade Control (FGC) method as developed by the Centre for Computational Geostatistics (CCG, University of Alberta-Edmonton), the CS models can be processed quickly to establish dilution and lost ore, and predict daily or short-term feed to the mill. The simulated nodes can be aggregated into selective mining units with adequate representation of likely geometries to be recovered from the pit, to mimic anticipated selectivity. An example from a large copper deposit is shown. The study provides an estimated stream of tonnages and grades fed to the plant by mining periods of interest and based on a specific mine design and schedule. The resulting cash flows support the economic and financial analyses of the Feasibility Study; also leads to improving mine schedules; and aids in developing blending schemes if necessary. INTRODUCTION The conventional approach of separating mineralized material into ore or waste categories does not always include a realistic amount of dilution and ore loss. Also, often it does not provide a good estimate of the grade that will be fed to the mill. If the grade control estimates are unbiased, they will over the long run represent the long-term average of grades fed to the mill; but the anticipated variability of mill feed from the pit and stockpile sources may be misrepresented. Some references on traditional grade control implementations can be found in Chunnett (1982); Davis et al. (1989); Srivastava et al. (1992); and Nowak (1992). Alternative methods based on economic variables improved significantly on the purely grade-based control methods, see Douglas et al. (1994). Further developments involved the use of geostatistical conditional simulations (CS) and profit models, which in several cases have been successfully implemented (Aguilar and Rossi, 1996; Rossi, 1997; Deutsch et al., 2000; Norrena and Deutsch, 2002; Neufeld, 2005; Jewbali and Dimitrakopoulos, 2009). But they can be impractical, mostly due to the lack of understanding of the methodology involved; even if semi-automatic dig limit drawing is implemented, there is always a need for is tedious and time consuming checking and corrections, even if using a single profit model derived from the simulated grades.

Jan 1, 2019

By Deniz Akbay

The strength of rocks and soil is a crucial design parameter in engineering projects, and it can be determined through various test methods such as uniaxial compressive strength, tensile strength, and shear strength. The point load index test is a popular indirect test method for predicting the uniaxial compressive strength of rocks. However, the reliability of the point load index’s estimation of uniaxial compressive strength of rocks is questioned due to the wide range of coefficients that are used to predict uniaxial compressive strength of rocks using point load index values. Factors such as the shape and type of rock specimen, practitioner, and test apparatus used can affect the accuracy of the point load index test. This study investigated the effect of four different specimen shapes used in point load index test (diametral, axial, block, and irregular lump tests) in predicting the uniaxial compressive strength. The rock samples were tested using four test procedures which are called diametral, axial, block, and irregular lump tests. The results showed that the irregular lump test was the most accurate in predicting uniaxial compressive strength, with the highest correlation coefficients and lowest mean absolute percentage errors. The point load index test can be used as a reliable predictor of uniaxial compressive strength of rocks when the irregular lump test is preferred.

Oct 18, 2023

By Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, José Gomes-Pereira, Inês Tojeira, Andreia Afonso, António Calado, Luísa Pinto Ribeiro

Since 2008, the Portuguese Task Group for the Extension of the Continental Shelf has been operating the ROV "Luso" (rated for 6000m depth) for geological sampling of the deep North Atlantic seabed, performing surveys on, e.g., seamounts and hydrothermal vent fields. Amongst other sensors, the ROV is equipped with a full HD video camera with which still images of the deep ocean floor are recorded. Fixed on the ROV’s frame are two underwater "line" lasers, each generating a sharp green line (532nm) over the seabed. The two lasers are paralleled and calibrated at a set distance. Provided that the camera’s angle of view is known, numerical values for seabed surface area may be calculated using direct measurements taken from the pictures containing the laser lines. We present the corresponding main mathematical formulas, which are derived from simple geometrical considerations, and discuss how to generalize these results for an arbitrary camera tilt or pan. We present an example of application of our method by estimating values for percent coverage of rock substrate versus sediment. Our results are also relevant for determining seabed polymetallic nodule abundances from still images obtained during ROV surveys.

Sep 1, 2014

By Galymzhan Karamyrzayev, Rashid Nadirov

Zinc ferrite ( ZnFe2O4) is a by-product of non-ferrous metal production and is considered a promising source of raw zinc. The most efficient way to extract zinc from its ferrite is via acidic extraction, specifically leaching by hydrochloric acid. A comparative study of synthetic zinc ferrite hydrochloric acid leaching in isopropanol, aqueous, and the mixed solvent was performed. Zinc ferrite was obtained by sintering a zinc and iron (III) oxide mixture. Crushed samples were subjected to leaching in 1 M HCl at 323, 333, and 353 K and pulp density of 1 g/100 mL. The dissolution of zinc and iron into solution in organic media reached 77% at 353 K, while in an aqueous environment this value was 65%. The activation energy of 70.0 kJ/ mol was found for the leaching process in an isopropanol environment, which is lower than that in an aqueous solution by 15%. The more efficient leaching effect of isopropanol is attributed to the lower dielectric constant of the alcohol which increases the affinity of chloride anions for zinc and iron cations at leaching.

Jun 5, 2022

By Fred W. Brackebush

In underground stopes that require more than minimal support, backfill is almost universally used. The term cut and fill stopingis used in a broad sense in this section, which describes underground mining methods requiring support. Support in stopes can be classified as local or short-term and general or long-term. Local support for the back of a stope, for example, can be accomplished with rock bolts or timber stulls. General support for the walls of the stope is provided by backfill. Local support provides a safe working place for the stope miners. General support, provided by backfill, preserves the access way to the stope and prevents large scale dilution of ore. Supported methods are a set of cut and fill stoping methods using backfill for general support and various local support methods. his section is subdivided into three chapters: 19.1 Cut and Fill Mining 19.2 Excavation Techniques 19.3 Backfilling Methods

Jan 1, 2008

By Dr. Jack M. Gillette

A system of models which simulate surface coal mining operations has been developed for use in mine planning and economic evaluations. Micromodels simulate individual mine operations for equipment selection and mine planning. Macromodels simulate all operations in the complete mine for economic evaluation of reserves. A cash flow analysis model makes a complete discounted cash flow analysis to deter-mine a required coal sales price or return on investment for evaluation of any mining project.

Jan 1, 1978

By H. Russell, N. DePriest, J. D. Quaranta

Valley-fill structures built of blasted rock overburden from Appalachian mountaintop surface mines pose many reclamation challenges. The steep mountainous terrain, short valley lengths, and straight stream channel profiles create significant challenges to implementing fluvial geomorphic landform design in terms of both form and function, and from a safety and constructability perspective. The fluvial geomorphic landform design approach balances erosive and resistive forces by considering long-term climatic conditions, soil types, slope profiles and vegetation types. Commercial geomorphic landform design software tools do not specifically analyze the stability and factor of safety for the computer-designed landform slopes. This research investigated slope stability parameters and factors of safety between a traditional valley-fill design with a geomorphic landform alternative. Slope stability assessments were performed on two profile geometries. Finite-element modeling of a permitted valley-fill and a geomorphic design alternative indicated that slope angle and internal angles of friction associated with the gradation of the overburden greatly affected the designed factor of safety for both designs. The geomorphic designed slopes yielded the highest factors of safety out of 14 models analyzed with all cases having factors of safety over 2.0. The high factors of safety are attributed to shallow slopes and beneficial surface and internal drainage.

Jan 1, 2014

By S. G. Malghan

Flotation is the primary method for copper minerals separation from porphyry ores. The need to process difficult-to-float porphyry copper ores presents challenges to engineers and scientists in several areas. This paper is concerned with summarizing generalized problems faced in the processing of porphyry ores and treatment methods to overcome the specific problems. Though some of the problems are interrelated the problems have been classified into three broad catagories. The case studies of some of the successful applications of innovative methods to solve problems related to ore mineralogy, metallurgical aspects of ore treatment and process variables show that quite often the problems are solvable by a judicious choice of flotation variables.

Jan 1, 1984

By Georgi N. Shoushoulov, Ventsislav D. Bozhilov

The mining conditions in the Meden Rid mine at levels below 1000 m from the Earth's surface are specific and rather severe. The rock temperature is about 40-45°C. The air humidity in the workings is approx. 80-90%. There is a limited capacity for additional fresh air supply. The air supply and distribution systems in the mine are very complicated. The airflow recirculation is due to the existing arrangement of the main fans. Certain accidental phenomena are difficult to predict. All these conditions create possibilities for heat and mass exchange between the rock and the air current thus hampering the control of the ventilation and air-conditioning in the mine workings. The changes in the temperature and humidity in certain characteristic places of the development and extraction workings are predicted. The refrigeration output required and the arrangement of the air coolers are also determined. A new ventilation and air- conditioning scherne has been developed. The new ventilation- cooling designs for levels between 1000-1200 m beneath the Earth's surface are based on the use of portable refrigerating machines having low water flowrate as well as heat-insulating and waterproof materials and methods for preliminary cooling of the orebody within the mining block.

Jan 1, 1997