Search Documents

By Ronald L. Wiegel

In the 2000 page Handbook of Mineral Dressing by A. F. Taggart, the subject of material or metallurgical balances is covered in only six pages of eve-straining type. Although Taggart's work was compiled before 1945, and there has been significant progress since then in most areas of mineral processing, the practicing metallurgist's approach to metallurgical balances remains exactly the same as described in those six pages. There are several portions of Taggart's text appropriate to introduce the subject of this paper which I would like to quote: "Milling Calculations. Computations of per¬formance in milling are complicated by the fact that it is a continuous rather than a batch operation, that the quantities of solid materials handled are large and usually mixed with water, hence difficult or impos¬sible to weigh. Fortunately it is possible to determine many facts concerning perfor¬mance without knowing weights, if the value of various constituents is known in some common unit, e.g., the content of some par¬ticular metal or mineral, or of water, or some ingredient soluble therein, or of par¬ticles of a particular size or falling within some particular size range, or the like."

Jan 1, 1979

By Christoph Schulte-Schrepping, Bou-Young Youn, Rolf Breitenbücher

"The main requirements of two-component grouts are a high workability and sufficient stability against sedimentation with a retention time of more than 72 hours, as well as a rapid strength development im-mediately after grouting. Component A usually consists of OPC, water, bentonite, and retarding agent. Component B, a liquid accelerator, is added to Component A during grouting at the end of the shield tail. Current investigations on different compositions of Component A showed a high workability lasting for at least 72 hours. The workability could be extended with increasing amount of the retarding agent to a certain degree. An increase of the bentonite content improved the stability of the mix, but had a negative impact on the flowability respectively the workability of Component A. High compressive strengths could be rather achieved by an adapted mixing ratio of Component A and B than by increasing the amount of the accelerator. Thereby, the interactions and compatibility of the selected constituents play an essential role. INTRODUCTION In mechanized tunneling with segment linings, the annular gap between segment ring and soil must be filled instantaneously with an adequate grouting mortar. The main functions of the annular gap grouting are to stabilize the tunnel lining and to minimize settlements of the ground surface at the same time. Thereby, two contradictory requirements are demanded on annular gap grouts: On the one hand a high workability and sufficient stability against sedimentation, on the other hand a rapid strength develop-ment immediately after grouting. Besides single-component grouts, which achieve the necessary stiffen-ing by dewatering into the surrounding soil, two-component grouts are used, especially in cohesive soils with a very low permeability. Basically, annular gap grouts are almost exclusively defined on empirical basis. Fundamental studies about the constituents and composition of the grout as well as the related achievable properties are still missing so far. Therefore, it is necessary to investigate the material-specific correlations regarding the relevant parameters of annular gap grouts – workability and flowability, stability of the mix as well as strength development – in comprehensive experiments. Based on the knowledge gained from the investigations, it should also be possible, to perform the grouting material according to a real design concept and thus, to ensure an adequate grouting in prac-tice considering the geological and hydro-geological conditions."

Jan 1, 2016

By Dejan Petrović, Pavle Stojković, Jelena Ivaz, Saša Stojadinović

In spite of the fact that flyrock phenomenon represents the real threat for personnel and machinery, it still remains insufficiently investigated. There are efforts, in the mining community, to explain the causes of flyrock, but the models capable to accurately predict flyrock occurrence and define the flyrock distance still do not exist. This article is an attempt to establish such a predictive model. The model utilized the adaptive nature of artificial neural networks and combined it with the accuracy of numerical modeling of physical phenomena. Necessary data were collected by high-speed camera recordings of actual blasts at three different surface mines and processed for further use for artificial network training. The result was a neuro-numerical couple which was capable to predict flyrock occurrence, estimate the launch velocity of flyrock fragments, and calculate the maximum distance of flyrock fragments. The safe distance was then calculated by multiplying the flyrock distance with a factor of safety. The article explains the procedure for data acquisition and processing, artificial network construction, training, and validation. It also explains the principles of flyrock distance calculation and, finally, provides a definition of factor of safety and safe distance. The results showed that the prediction was satisfactorily accurate and reliable.

Oct 22, 2021

By H. M. King

A combination of chemical, statistical, geographic, and microscopic analyses reveal that sulfur in West Virginia coals is extremely variable in both form and abundance. Coals in southern West Virginia typically contain less than 1% total sulfur with organic sulfur being the dominant species. Northern West Virginia coals average about 2% total sulfur, mainly contributed by sulfur minerals. In addition to these regional trends, significant variations in sulfur form and abundance exist both vertically and laterally within individual seams. On both regional and local scales, the pyritic sulfur component can vary significantly in mineralogy, particle shape, maceral association, and particle size.

Jan 1, 1986

By S. K. Sahoo, S. K. Sharma, U. K. Singh, G. S. P. Singh

This research focuses on the strata control issues in a Bord and Pillar depillaring working under the influence of dead load condition of voluminous and fragmented softcover of overburden dump material. It reports the modeling of a mine working through the FLAC 2D software under the Indian geo-mining conditions. The modeling results of an actual mine working under softcover were compared with that under the intact overburden condition to assess the influence of the soft overburden over the depillaring working. The modeling work involved progressive caving of the strata and the cyclic goaf filling following the modelsimulated occurrence of main fall and periodic caving. Mohr-Coulomb Failure criteria along with a simplified strain-softening (MCSS) model was used to study the failure and caving mechanism. Salamon’s compaction model was used to simulate compaction and resultant stress recovery in the goaf material. Comparison of the model findings was done in terms of load on supports, abutment stress, and convergence, apart from the stress redistribution and failure mechanism. The load transfer mechanism of the soft overburden was also studied for an overall understanding of the strata behavior in such workings.

Jun 16, 2020

By T. Rasmussen, T. G. Jørgensen, T. Fischer, R. K. McLimans, C. Knudsen, D. Frei

Ilmenite-bearing paleo-beach deposits were discovered in Jylland, Denmark using a combination of Ground Penetrating Radar (GPR), portable X-ray fluorescence (XMET), bulk XRF analyses, Computer Controlled Scanning Electron Microscopy (CCSEM), and wire line logging. The Miocene-age paleo-beach deposits are located below a thin Quaternary cover in a region of very moderate relief and essentially no outcrop demanding unique approaches in exploration. Initially, an isopach map of the Quaternary is prepared from existing water well data. A geological model for likely occurrence of Miocene paleo-beach deposits is generated and the coincidence of thin Quaternary cover and potential paleo-beach deposits define targets for detailed exploration. The defined targets are traversed with GPR to identify paleo-beach structures which are then used to define a drilling program. This methodology located a paleo-barrier island at the Vorslunde location with more than 10% ilmenite in the sand. During the drilling process, the TiO2 and heavy mineral contents of the sand were logged every meter with a portable XRF unit (XMET) and subsequently calibrated more accurately by comparison to bulk XRF and CCSEM analyses for selected samples. The bulk XRF data also provided more complete compositional information. Insitu determination of geology, heavy mineral abundance, and corroboration of the XRF logging was done using wire line logs, a combination of spectral gamma and induction conductivity logs. Detailed characteristics (abundance, grain size, shape) and chemical composition of minerals was determined by the GEUS CCSEM methodology (Frei et al, this vol.). The average weight percent TiO2 for all Ti-minerals is 62%, 60% excluding rutile. That elevated TiO2 content (>> ilmenite stoichiometric value, ca. 50 %) indicates that ilmenite experienced an iron-leaching environment. The source of the sand deposit was investigated by dating contained zircon. The results show that the likely sources of zircon are in southern Norway and southwestern Sweden with common zircon ages of ca 1100 Ma. and 1500 Ma.

Jan 1, 2005

By Clinton Birch

The multiple-criteria decision analysis is a technique that helps to find an optimal solution by evaluating conflicting criteria. In this study, an approach to perform multiple-criteria decision analysis for cut-off grade optimization, which considers the diverse stakeholder groups prevalent in the mining industry, is presented. The optimization model developed in this approach links the resource block model to the financial model, enabling the process to either maximize profit, net present value, revenue to the State, or extend the mine's life. To identify the optimal cut-off grade in each case, the Excel Solver function is utilized. Although it has limitations, the Solver function can still be modified to handle models with thousands of block values for determining input variables based on the target value. Following stakeholder engagement and dialogue, a single weighted average cut-off grade can then be determined. This approach is demonstrated for nine South African Witwatersrand gold mines.

Jun 25, 2023

By H. J. Sutherland

This paper reviews the results of the subsidence research prop ram at Sandia National Laboratories. The manuscript highlights the following: the application of empirical methods (profile functions) to the subsidence above longwall panels in the U.S.; the use of the "rubble model" to describe the behavior of broken strata as it distends when it falls to the Mine floor (or top of the rubble pile) and then is subsequently compacted as it is loaded by overlying elements of strata; and, the application of physical modeling techniques (centrifuge simulations) and numerical techniques to study the failure mechanisms in highly structured stratigraphy. The capabilities of the latter two are illustrated ')y comparing their predictions to the results of a field case that has complicated stratigraphy.

Jan 1, 1982

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of underground and surface operations. The East Ertsberg skarn system (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production from the third lift deep ore zone (DOZ), has reached 80 kt/d (88,000 stpd) during 2010, with this rate sustained through 2015. The orebody was proven below the existing caving level, with the next vertical block called the deep mill level zone (DMLZ).

Jan 1, 2010

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By Frank Agyemang, Zainab Nasrullah, Richard LaDouceur, Mehran Saddat

To sustain the circular economy, defence applications, and other renewable technologies, recycling rare earth elements (REEs) and other critical elements from their secondary resources is important. This cause has resulted in rigorous research and development for viable extraction and separation of REEs. Previously, Sm-Co recycling has been done with technologies, which fall under the categories of pyrometallurgy, physical separation, and hydrometallurgy. All these methods have limitations associated with energy, cost, and environment. Reportedly, the chemical leaching technology has successfully recovered and separated Sm-Co. Still, it has limitations associated with slow mass transfer and leaching kinetics, and there is a need to intensify the process to make it time efficient. This approach has also adversely impacted the environment by an extensive use of toxic, corrosive, non-selective, and expensive reagents. In this research study, chemical leaching of Sm-Co was performed using this new class of solvents, Deep Eutectic Solvents (DESs), which fall under the category of ion metallurgy. Four different DESs were used, proven to be green, non-toxic, biodegradable, cheap, and selective for cobalt over samarium by 82% leaching conversion. To improve the slow mass transfer and leaching time, this new technology of resonant vibratory mixing (RVM) was also tested. RVM intensifies mixing by establishing near instantaneous, low energy mixing conditions through resonance. It has been shown to improve the adsorption kinetics and was tested for the leaching kinetics. Four combinations of DESs were prepared, which are made up of two quaternary salts: Choline Chloride and Tetra Butyl Ammonium Chloride, and three organic compounds: Oxalic Acid, Urea, and Ethylene Glycol. These combinations were used for chemical leaching of Sm-Co with leaching factors of time, temperature, and type of DESs. After leaching, the samples were tested with and without resonant vibratory mixing with conditions of time, intensity (%), and type of DESs. Samples were analysed with Induced Coupled Plasma - Optical Spectroscopy (ICP - OES). Future work will involve a life-cycle assessment to assess the RVM technology with other conventional mixers, and an extensive study of DES properties to improve selective leaching.

Feb 1, 2025

By R. E. Thill

An ultrasonic, pulse-immersion apparatus and method are described for determining the effects of moisture on the dynamic elastic properties of rock. The method provides an alternative approach for assessing the moisture sensitivity of rocks. Ultrasonic wave velocities are continuously monitored in immersed rock samples as a function of water absorption and time up to saturation. Moisture effects on compressional wave velocity vary as a function of the type of rock and the time and amount of water absorption. Regression analyses are used to curve-fit plots of the data and to derive empirical expressions for compressional wave velocity as a function of water content for different categories of rock. Results indicate that compressional wave velocity can be used to predict both the moisture content and its effect on strength and deformational properties of rock. These results have potential for detecting or monitoring bad roof conditions in situations where the mine rock exhibits strength degradation with moisture absorption.

Jan 1, 1986

By Nick Salisbury, Alan Howard, Scott Tunison

INTRODUCTION Geotechnical investigations for tunneling projects typically use vertical test borings and, to a lesser extent, angled borings. Horizontal drilling applications were often limited to specialty testing programs and to perform probe drilling from a tunnel boring machine (TBM) as part of production tunneling. The former often involved cumbersome setups with skid rigs and cribbing in a pilot tunnel or shaft. The latter usually was limited to generic probing for rock quality and ground water conditions with no sampling. Neither yielded continuous core at production rates suitable for design and construction planning. Conventional vertical investigations still make sense in many instances, particularly for tunnels planned beneath urban settings where truck access is convenient and where the tunnel horizon is not readily accessible via a portal or shaft. However, equipment is presently available to conduct horizontal geotechnicall investigations at reasonable production rates and cost. Advantages include continuously sampling the tunneling horizon and minimizing “access drilling” to get the zone of interest at the underground construction horizon. Horizontal boring lengths of up to approximately 800 m are considered feasible and those in the range of 150 to300 m are now routine. These capabilities make horizontal borings an attractive option to consider when looking at deep tunnels beneath ridges, especially where access is limited. Fewer drilling staging sites can also mean reduced environmental impacts when investigating tunnels proposed beneath sensitive lands such as public wilderness areas. Investment in early construction packages to develop portals for investigation access and, possibly in excavating test shafts for the same purpose should even be considered. Potential benefits in the form of achieving improved overall project costs using horizontal borings exist because of the significant additional data collected in the tunnel horizon. For this reason they should be considered during the routine cost-benefit analyses generally conducted for planning geotechnical investigations for tunneling. The authors also believe that collection of such data will reduce Geotechnical Baseline Report (GBR) conservatism and lead to lower potential for

Jan 1, 2005

By Santosh Kumar Ray, DEBASHISH MISHRA, Niroj Kumar Mohalik, SOMU MANDAL, Jai Krishna Pandey, Asfar Mobin Khan

Coal is a low-cost and high-calorific-value fuel. The coal mining industry worldwide has been suffering from severe accidents due to coal dust explosion hazards since its inception. Statistically, it was observed that 12,489 fatalities had occurred in 104 reported mining accidents from coal dust explosions during 1900–2020. There are numerous methods for detection, prevention, and control of coal dust explosions in mines. The underground mining environment is unpredictable and has an array of variables. These undulating factors make it difficult to prevent or control the coal dust explosion hazard. However, coal mining is done aggressively throughout the world, especially in developing countries as coal is a major source of thermal energy used in power plants contributing to about 38% (IEA, (2019), World Energy Outlook, IEA, Paris https:// www. iea. org/ repor ts/ world- energy- outlo ok- 2019.) of world electricity. Worldwide, coal dust explosibility studies are carried out in experimental mines, laboratories, and simulations. The complexity, lack of proper infrastructure, and unavailability of laboratory equipment sometimes make it difficult to study coal dust explosibility. The authors have discussed in detail and proposed that the CFD modelling can be a viable option for studying and evaluating coal dust explosibility.

Jun 29, 2022

By Steve Klein

The Transbay Downtown Extension (DTX) in San Francisco involves the construction of a large-span tunnel with a width ranging from 43 to over 60 feet. The tunnel will be excavated using the New Austrian Tunneling Method (NATM), also known as the Sequential Excavation Method (SEM), in highly fractured and sheared rock. This paper discusses the FLAC (Fast Lagrangian Analysis of Continua) analyses that were completed for conceptual design of the tunnel support system and to develop surface settlement estimates for the evaluation of measures to protect existing buildings located above the tunnel from damage.

Jan 1, 2008

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

By Changjiang Li, Jun Yang, Qiang Fu, Xu Chang, Xing Wu, Yubing Gao

With the development of underground mining, the deformation of roadway floor has increasingly become a major constraint on the safe and efficient production of coal mines. To address the floor deformation that was caused by massive stress concentration in roadway, an innovative method based on deep-hole directional tensile blasting technology is put forward. By taking No.122108 working face in Caojiatan Coal Mine as engineering background and analyzing the mechanism of deformation, a numerical simulation and field test are carried out to verify the effect on deformation control of this technology. It is found that the deep-hole directional tensile blasting technology can actively control the fracture position of the roof in the gob area and cut off the stress transmission path, so as to relieve the stress in the roadway. And since different blasting parameters have different impacts on the stress relief effect, a numerical simulation is implemented and it is found that the stress relief effect is the best when blasting depth is set to be 32 m and the blasting angle be 60°. By applying the optimal blasting parameters to the field engineering test, it can be seen that the deep-hole directional tensile blasting technology could effectively reduce maximum stress value and stress field range of the both sides of the roadway, and make the stress field far away from the roadway, thus effectively controlling the deformation of the roadway floor. The deep-hole directional tensile blasting technology can effectively solve the problem of roadway floor deformation and can be safely applied to engineering sites.

Jun 13, 2023

By William S. Alldredge

The Washington Metropolitan Area Transit Authority(WMATA) officially came into existence in February 1967 after the District of Columbia, Maryland, and Virginia joined in a com¬pact pursuant to Federal creative legislation signed the previous November to build a regional rapid rail transit system called METRO (1). The parent organization was the National Capital Transportation Agency (NCTA), a Federal agency, subject to Federal statutes and regulations. Soon after the completion of the transition from NCTA to the new "non-Federal" status of the Authority, the Board of Directors of the Authority formally adopted procurement policies and procedures (2). These are specific statements concerning competition by formal advertising for bids or by solicitation of proposals for negotiation, contracting authority, approval of awards, awards of contract modifications, and processing of claims and disputes. These policies and procedures are silent as to Federal procurement statutes and regulations. But because of the Authority's origin, the sensitive nature of the compact among the several sovereign jurisdictions, Federal financing of two-thirds of the costs, and the resultant surveillance by the General Accounting Office over staff operations, the Authority's procurement practices follow closely Federal regulations adapted to WMATA's needs. This is an important point and is the foundation of contractual relations between the Authority as the owner and its construction contractors. Various constraints and flexibilities of this arrangement with respect to excavation and tunneling contracts will be pointed out in the ensuing discussions.

Jan 1, 1974

By Pan Gao, Songyang Yin, Zhibiao Guo, Jinglin You, Yuhui Li

Under the geological conditions of the interaction of upper goafs and lower working face in deep mining, coal seam mining causes a large stress concentration, which may lead to large deformation of the surrounding rock and rock burst risk. The research reported herein is aimed to utilize the FLAC3D software to establish a three-dimensional numerical model and analyze the law of the surrounding rock stress evolution during coal mining under complex geological conditions. The simulation results reveal that the peak abutment stress reaches its maximum value at 20–30 m in front of the working face, about 1.8–4.3 times the original rock stress, and the peak stress is larger in the stable mining stage. Along the dip of the working face, the peak stress occurs about 8–10 m away from the roadway side. The upper barrier coal pillar and the interval coal pillar in order exhibit stress concentration areas of 142 m and 88 m. According to the law of the deflection stress distribution of the surrounding rock in the presence of various widths of the coal pillar, a 10-m coal pillar between the roadway and the adjacent goaf could enhance the stability of the roadway. For the stress concentration area, drilling holes with a depth of 20–25 m are utilized to reduce the pressure, and anti-impact supports are installed in the middle of the roadway. Due to the varying stresses of the rocks around the roadway, partition prevention and control countermeasures are capable of efficiently preventing the instability of the surrounding rock.

Mar 22, 2023