Search Documents

By T. Stauffer, B. McGunegle, A. Adu-Acheampong

The Fairmount Minerals, Inc., Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 15-inch-diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially-available, high-volume/low-pressure fans combined with a systematic layout of control structures. The recommended re-design was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2007

By Rosa Malena Fernandes Lima, Kerollan da Silva Ramos, Joyce de Assis Silva, Geriane Macedo Rocha

This study evaluated the effects of collector type amide-amine compared with those of conventional etheramine acetate (both cationic collectors) on the surface properties of quartz and hematite. An examination of certain properties of the reagents indicated that the new collector amide-amine has CMC (critical micelle concentration) and pKa values (100 mg/L and 8.2, respectively) significantly lower than those of etheramine (800 mg/L and 9.4, respectively). Microflotation tests showed that the recoveries of quartz with amide-amine in all the concentrations tested were higher than those with etheramine. This is attributed to its lower CMC and pKa values. The selectivity window between quartz and hematite flotation using amideamine was higher at pH 10.5 (approximately 80% for 5 mg/L). Therefore, the use of starch is not necessary in siliceous itabirite flotation by amide–amine collector. Zeta potential measurements and infrared spectra reveal that the adsorption of amide-amine collector on quartz surface occurs mainly by electrostatic attraction. Considering the better collectability of amide-amine for quartz flotation and lower adsorption affinity for hematite surface than etheramine, the amide-amine is a promising collector to be used in reversal iron ore flotation.

Jul 30, 2021

By F. Habashi

Siberia, a vast country rich in mineral resources and a large number of different ethnic groups. To the east of Lake Baikal is Buryatia with capital Ulan Ude. The Buryat are closely related to the Mongolians. Ulan Ude is connected to Ulaan Baatar (Ulan Bator) the capital of Mongolia by train – a 26 hours trip. Getting a visa to Russia is not a simple case. Visits to metallurgical research laboratories, Lake Baikal, and historical museums are enriching experience.

Jan 1, 2006

By Jon Pocock, Ashma Singh

The traditional approach for the beneficiation of South African siliceous sedimentary phosphate ores has been reverse cationic flotation. The robustness of this approach, however, has been a concern due to its sensitivity to parameters such as slimes content, headgrade ( P2O5 and SiO2 content), reagent dosages and conditioning times. The phosphate mineralisation for the ore body under investigation is predominantly carbonate fluorapatite composed of mainly quartz and apatite and minor amounts of chlorite, ilmenite and carbonates. Beneficiation of low grade sedimentary ores containing calcareous impurities, such as calcite and/or dolomite in addition to siliceous gangue, is required to meet the increasing demand; therefore, much research has been carried out to find an alternative technique to beneficiate this material. This paper investigates traditional flotation approaches versus the currently adopted ‘Crago Process’. Comparative results are presented in terms of upgrade potential for the production of concentrate rock for downstream applications. The novelty of the ‘Crago Process’ lies in its double stage approach, i.e. direct fatty acid flotation followed by reverse cationic amine flotation. The Crago process was able to achieve higher upgrades reporting at 32.1% P2O5 compared to conventional cationic flotation only achieving grades of 18.5% P2O5. Furthermore, the recovery gain was 3%.

May 13, 2023

By Jacob Carr, Christopher C. Jobes, Chenming Zhou, LaTasha R. Swanson, Jennica Bellanca, Jingcheng Li

Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM— the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered.

By Jacob Carr, Christopher C. Jobes, Chenming Zhou, LaTasha R. Swanson, Jennica Bellanca, Jingcheng Li

Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM— the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered.

By S. Que

Local community acceptance is a key aspect of planning and managing mining projects, whether through sustainability assessment and reporting or corporate social responsibility programs. However, there has been very little research to understand the determinants of community acceptance. This paper seeks to identify key mine characteristics and demographic factors that influence individual acceptance of mining projects. Six demographic factors and 16 mine characteristics were selected based on literature review. Four of the six demographics factors were confirmed to be significantly (p < 0.05) correlated with people?s attitude of the importance of the mine characteristics. All sixteen mine characteristics are identified as important factors. The most important mining factors are Job opportunities, water shortage or pollution, air pollution and land pollution. Both the mining and control groups have same opinion of 12 mining characteristics and differ on four (infrastructure improvement, labor shortage for other businesses, noise pollution, and mine life). During design and management of mines, this data can be used as a reference. This result will facilitate better choice experiment (survey) design for discrete choice modeling. Such discrete choice models can provide a viable framework for data-driven community engagement and sustainable mine management.

Feb 23, 2014

By Omar A. Muhtadi

6.1 INTRODUCTION The three most critical factors in successful heap leaching operations are: • The methods employed to pretreat ore (i.e, crushing and agglomeration); • Placement of ore on the leach pad (heap building techniques); and • Wetting of the ore with cyanide (solution application techniques). Improper execution of any of these initial steps may result in a substantial sacrifice of total metal extraction or, in the worst case, in project failure. Ore preparation in terms of crushing and agglomeration was discussed in Chapter 5; this chapter therefore focuses on commonly employed techniques for heap construction and solution application. The main objective of heap construction is to obtain the most homogeneous heap possible. "Channeling" of leachate in heaps with preferential seepage paths leads to preferential leachate distribution and uneven/incomplete extraction. The two main contributing causes of channeling are inadequate attention to heap construction and uneven solution application. These pitfall s can best be avoided through a knowledge of the various techniques available and the applicability and success of these techniques with various ore types and site conditions. The remainder of this chapter provides a discussion on these two subjects. 6.2 HEAP BUILDING TECHNIQUES Successful heap building techniques vary with the type of ore and, since no two orebodies are exactly alike, some slight modifications are usually necessary for each specific project. However, it is possible to generalize in terms of the appropriate techniques to be used with ores having similar characteristics. This section discusses the three most commonly used methods of heap construction and provides some guidelines with regard to ore types, construction constraints, and lift height parameters for each of the three. 6.2.1 Run-of-Mine Dumping and Dozing The run-of-mine method of heap building can only be used with ore of a highly silicious nature (i.e., ore which will not generate a large amount of

Jan 1, 1988

By M. Kung, D. Schwegler-Berry, V. Castranova, D. Lewis, H. Abrons

Pulmonary responses to coal mine dust exposure were investigated by analysis of bronchoalveolar lavage specimens from non-smoking coal miners (n-12, mean age-43 ± 2 years, mean underground exposure-17 ± 2 years) and from non-smoking normal volunteers (n-18, mean age-43 ± 2 years). Spirometric and diffusion capacity indices were monitored as part of a physical exam. Lavage was performed in a subsegment of the right middle lobe by instillation of 200 ml of warmed saline solution in 50 ml aliquots and recovery by gentle suction. Specimens were centrifuged at 500g for 5 minutes at 2°C. Total and differential cell counts were recorded. Secretion of oxidants measured by chemiluminescence, surface morphology (spreading and ruffling), and lymphocyte parameters were determined. Lavage fluid was analyzed for the presence and quantity of acute phase reactants and immunoglobulins. Pulmonary function measurements as well as recovered lavage volume, total lavagable cells, and differential cell counts were similar in both miners and controls. Both resting and phorbol myristate acetate-stimulated chemiluminescence were also similar in miners and controls. In contrast, particle-stimulated chemiluminescence was significantly decreased in the alveolar macrophages from the miners (48% of control values). Morphometric analysis of scanning electron micrographs indicate that phagocyte surface spreading was similar in miners and controls. However, surface ruffling was 127% greater in the miners compared to controls. Lymphocyte subpopulations were similar in miners and controls. Protein analysis of the lavage fluid revealed lower total protein content in the lavage fluid of miners. However, the concentration of albumin, IgG, and IgA were similar in miners and controls. We conclude that most indices were normal in underground miners working under the current dust standard of 2 mg/m3. The decrease in particlestimulated chemiluminescence and the increase in surface ruffling in miners may suggest the beginnings of particle overload and activation of the macrophages. In addition, a decrease in total protein was noted in lavage fluid from miners.

Jan 1, 1991

By N. E. Norman

A great deal of effort has been put forth in recent years to arrive at accurate projections of the demands for tunnels in this decade. In reviewing the statistics presented by various study groups, it appears that during the decade from 1960-69, there were some 1,335 miles of rock and soft ground construction tunnels excavated throughout the world. These statistics indicate 645 miles of rock tunnel and 689 miles of soft ground tunnel were excavated during the last decade. This is expected to increase to 3,000 miles in the 1970&apos;s according to projections made by various authorities in the field of construction tunneling. I point out the above statistics to emphasize two main points: (1) The demands for tunneling in this decade alone are staggering. (2) There is a fairly even distribution in the amount of rock tunneling and soft ground tunneling being excavated. Unfortunately, available statistics do not answer many important questions about tunneling which are of great importance to the contractor and to boring machine designers. For example, how many of the projects completed in the past decade involved both soft ground and rock tunneling? How many projects involved tunneling in conditions where both rock and soft ground were contacted at the same face. While the answers to these questions remain unanswered, I am sure most of you can think of numerous examples of projects where mixed face conditions are prevalent. Many of you are probably familiar with the Austin Crosstown Interceptor which was bid last month in Austin, Texas. Here is a project involving 57,000 feet of tunnel where limestones and clay shales are expected to be traversed. Another project, the Tonner Tunnels No. 1 and No. 2, near Los Angeles, involve some 22,000 feet of tunnel where mixed soil and rock conditions are expected. A large majority of the projected tunnels for this decade are to

Jan 1, 1997

By Jiawang Hao, Qinglong Zhang, Liang Han, Chuhan Wang, Shenfang Chen, Lan Qiao

The surface collapse and surrounding rock failure caused by goaf instability are the mining disasters that cannot be ignored. It is of great value to evaluate the stability of goaf accurately and treat it economically for the mine safety and the maintenance of ecological environment. However, in previous studies based on numerical simulation methods, the spatial complexity and the irregularity of actual goaf were not considered. Therefore, based on the internal space data of goaf obtained by high-precision laser detector, the goaf stability was comprehensively analyzed through Plaxis software and two-stage fuzzy judgment theory in this study. To effectively improve the goaf stability, the optimal backfill parameters for the goaf treatment were obtained by a series of mechanical tests. The research results provide some good references for the stability evaluation and the treatment of underground goaf.

Sep 26, 2023

By G. W. McMahon

Following the Sago Mine accident, the U.S. Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 0.3-m (1-ft) resolution map of the mine to produce a 3-dimensional (3 D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3 D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jul 1, 2010

By Charles T. Ford

In 1971, Bituminous Coal Research, Inc~ established a program to provide the coal industry with the necessary information and technical capability to investigate and evaluate potential problems concerning trace elements in coal and coal-related materials. The initial efforts at BCR in developing or adapting analytical procedures for the precise determination of trace elements in the parts per million to parts per billion range were detailed in a report titled "The Development of Analytical Methods for Determining Trace Elements in Coal and Coal-related Products." A subsequent reports contained descriptions of reliable analytical methods refined by BCR for determining mercury in coal and coal ash and also in coal mine water. his paper reports initial progress in applying recently-acquired trace-element analytical capabilities to solving potential coal industry problems. In this case, the effect of a coal-cleaning process on the distribution and removal of potentially harmful trace elements in coal was evaluated. Coal cleaning offers the possibility of controlling potentially harmful emissions resulting from combustion of large tonnages of coal by removing the pollutants prior to combustion.

Jan 1, 1977

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

As a result of the rise in global demand for pure copper, there is urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as an effective and efficient leachant for the dissolution of chalcopyrite. This work reports different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from Wase Local Government Area, Plateau State, Nigeria, and assayed as 11.30 wt% of Cu. At the optimum leaching conditions (0.4 mol/L NH3-( NH4)2SO4 leachant concentration; 75 °C reaction temperature; 45 μm particle size), the extent of chalcopyrite ore dissolution reached 87.4% within 120 min. The dissolution rate was affirmed to conform to the diffusion control mechanism with the activation energy, Ea, of 38.84 kJ/mol and a reaction order of 0.661 for the leachant concentration being established. The leaching mechanism was affirmed by characterizing the raw ore and the leached product by XRD and SEM-EDS analysis. Ascertaining optimal leaching conditions for copper using alkaline leachant is advantageous from the environment and economic points of view.

Jan 6, 2023

By Hiroshi Soda, Atsumi Ohno, Hiroyuki Yamazaki, Alexander McLean

INTRODUCTION The method of heat removal during a casting process strongly influences the crystal morphology of the cast product and hence the metallurgical and mechanical properties of the solidified materials. In this paper, the Ohno Continuous Casting Process (OCC) is described in terms of the casting conditions and the type of structure observed in the cast product. Significant improvements are observed in workability, fatigue strength and corrosion resistance of castings produced by the OCC method, Ohno (1988). Applications of this technique to low melting point nonferrous metals and alloys are discussed. The feasibility of the application of this technology to high melting point materials is outlined. THE OCC PROCESS The OCC process involves delivering liquid metal into a heated mold, the temperature of which is held just above the solidification temperature of the metal to be cast. This is the key point which differentiates the OCC process from the conventional continuous casting method. A schematic illustration of the OCC process is shown in Figure 1. The Formation of a Single Crystal When the mold is heated above the solidification temperature of the metal to be cast, nucleation on the mold surface is prevented and solidification takes place only at the mold exit. The heat is extracted through the product being cast by a cooling device located near the mold outlet. Crystals are formed only at the tip of the dummy bar at the start of casting, and as the dummy bar travels away with a progressively increasing speed from the mold, the position of the solid liquid interface will align with the mold exit, producing a unidirectionally

Jan 1, 1990

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

By J. B. Hadaway

The current limit to power transmission for grinding mills through one mill pinion is approximately 7,500kW. Above this power rating either twin pinion arrangements or Gearless drives are required. The SMTP concept was developed to overcome this limitation by using two pinions with a single large drive motor. The SMTP mill drive offers major advantages in capital cost and greatly simplifies plant layouts, while using an innovative adaptation of industry-proven single helical gearing. Through the use of a single motor, provision of variable speed drive is greatly simplified. The SMTP can also be used for significant power upgrades on existing mills.

Jan 1, 2001

By Kwame Awuah-Ofei, Sisi Que, Shaochun Yuan, Yumin Wang, Ziwei Ding

This research sought to facilitate improved stakeholder analysis in mining by providing further insights into the preferences of local community members using discrete choice theory. While recent research has demonstrated the usefulness of discrete choice theory in mining stakeholder analysis, no previous work has examined which discrete choice model (DCM) is most suitable. This paper provides a research note on a case study in a mining community that was performed to compare three DCMs. After a thorough examination of the benefits and deficiencies of all models, this study concludes that the conditional logit model stratified by questions is the most useful DCM for mining stakeholder analysis. The recommendation is based on the usefulness and accuracy (ability to match the survey data) of this model.

Jul 25, 2022

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT The pervasiveness of high-fidelity video games raises expectations of quality, detail, and lighting in virtual reality (VR) applications. However, high-quality models of mining equipment and environments are often not readily available, and developers may not be familiar with the latest techniques, such as physically based rendering (PBR). Because a consistent aesthetic is critical for maintaining immersion and controlling visual stimuli in research as well as in training, researchers at the National Institute for Occupational Safety and Health (NIOSH) created an asset development workflow. This paper details this workflow, including precision modeling and PBR techniques as well as a rigorous review process. It also describes lessons learned in the creation of photorealistic VR assets. BACKGROUND Virtual reality (VR) describes the simulated experience generated by an assemblage of hardware and software that are used to immerse the user. Over many years VR developers targeted the development of virtual environments (VE) toward various purposes: entertainment, the treatment of phobias [1], rehabilitation [2], and training [3]. A large part of the VE development includes digital assets, where digital assets refer to the non-programmed elements including 3D models, audio, and user interface. Because vision provides nearly 10Mbps of data [4] and accounts for the majority of all sensory input combined [5], a focused effort on asset appearance in VEs is warranted. Furthermore, research has shown that higher-resolution imagery increases search performance and training transfer, necessitating high-fidelity assets [6, 7]. In addition to being visually appealing, it is important that the assets and environment are also dimensionally accurate and consistent in order to elicit appropriate responses from the end users as they interact with and among these items [8, 9]. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed VEs and digital assets under several research projects over the course of the last two decades [10, 11, 12, 13]. This work has provided researchers with a strong knowledge base for digital asset development. However, the assets themselves have had limited reuse value. Due to the extended timeframes and limited scope of these projects, the previously developed assets are not consistent in visual quality and dimensional accuracy. Moving forward, researchers wanted to minimize future development time and use of resources as well as adopt new asset development tools and game engine technology. Therefore, the aim of this paper is to document a new asset development workflow including geometry, materials, UV layout, and shader implementation combined with review steps in order to produce high-fidelity simulation assets that are accurate with consistent characteristics, using repeatable methodologies that are well documented.

Jan 1, 2019

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2013 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration for the year 2013: 1) budgetary statistics expressed in U.S. nominal dollars provided by SNL Metals & Mining (SNL) of Halifax, NS, Canada (formerly Metals Economics Group (MEG); 2) regional and site-specific exploration activities that took place in 2013 as compiled by the USGS; and 3) regional events that affected exploration activities, including economic, social and political conditions, that were derived from published sources and unpublished discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources are used to develop commodity and regional compilations, reported statistics may vary depending on the source and type of data that are being reported. The SNL data summarize planned company budgets for worldwide exploration activities in 2013 for 20 nonfuel mineral commodities based on surveys returned by companies primarily focused on precious metals (gold, platinum-group metals and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (coal, iron ore, phosphate and potash), and specialty commodities (diamond, lithium, niobium, rare-earth elements, tantalum and uranium). Information on uranium exploration activities was included in the MEG overview for the first time in 2007. MEG included data on the commodities lithium, niobium, phosphate, potash, rare-earth elements and tantalum for the first time in 2010 because of the increased topical significance of these commodities. Since 1999, companies with exploration budgets of $100,000 and greater were included in the MEG and SNL compilations. SNL budget estimates exclude aluminum, coal, and oil and gas. Budget estimates for iron ore have been compiled since 2011 but reported separately. The post-1999 budget surveys by MEG and SNL cover at least 90 percent of world?s reported nonferrous, nonfuel mineral exploration budgets; the 2013 survey is reported by SNL to cover an estimated 95 percent of these budgets. The 5 percent that is not covered is accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities.