Search Documents

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009

By Rong Lu, Hao Wu, Bing Dai, Guoyan Zhao, Li Cheng, Weizhang Liang

Affected by the disturbance of blasting activities, deformation instability and rock dynamic disasters are prone to occur in deep hard rock roadways. Thus, it is particularly necessary to understand the failure behavior of rocks and roadways under dynamic loads. In this study, a series of impact loading tests were carried out on sandstone samples with and without a circular cavity by a modified split Hopkinson pressure bar (SHPB) test system. The mechanical properties and energy evolution of the samples were systematically investigated, and the effect of cavity size was analyzed. The results showed that the presence of the cavity in the samples weakens the dynamic compressive strength by more than 10%, and the peak strain and brittleness are also reduced to varying degrees. Under dynamic loading, spalling cracks occur first on the roof and floor of the cavity, and then different numbers of shear cracks are formed on the sample diagonals. The eventual shear failure mode is the result of the connection of the shear cracks and the cavity. As the cavity radius increases, the dissipated energy density and fractal dimension both grow accordingly, leading to smaller and smaller rock fragments. The dynamic failure behavior of the circular cavity can be well explained based on the dynamic stress distribution law. Overall, this study can provide a reference for the study of the mechanism of rock burst in deep roadways.

Feb 18, 2021

In 2002 the authors updated the MFire model developed by the US Bureau of Mines. MineFire, developed by Mine Ventilation Services, Inc. (MVS), uses the MFire model to perform mine fire simulations on typical mine ventilation networks. The MineFire program is capable of producing visual schematics and other analysis tools for input and output of the MFire model. The MFire model, however, was limited to 500 branches and 10 fans. This paper discusses the newly modified MFire model that is now capable of modeling over 5000 branches and over 400 fans among other expansions and improvements. Given the long history and proven track record of MFire, the expansion did not modify the core calculation methods or results. This paper focuses on a general discussion of the MFire program and issues encountered in expansion of the algorithm. An example large network with simulation results is discussed.

Jan 1, 2011

By Viktor Lishchuk, Olof Martinsson, Tobias E. Bauer, Elena Haller

Freely accessible and non-confidential real-life geological data sets from mineral deposits are desirable for the wide range of applications in research and education. However, publicly available statistical data are limited in their number and quality—they contain reduced information about geological, geophysical, geotechnical, chemical, mineralogical, and other relevant properties of deposits. This makes such data insufficient for scientific purposes. However, the amount of geological knowledge obtained for a variety of deposits in the past allows the construction of an idealized synthetic ore body model using analytical approach. Such a model could be used for education purposes and testing basic scientific theories, e.g., visualization of deposit structure; teaching sampling strategies; testing new algorithms for mine planning; or comparing geostatistical modeling methods. This paper presents an analytical approach to simulate volcanic massive sulfide (VMS) deposits and shows how synthetic deposit model can be constructed and further used for studying sampling with drilling and simulating folding and faulting.

Jan 14, 2021

By Wedam Nyaaba, Samuel Frimpong, Bruno Ayaga Kansake, Irene Akalanyaba Ateng

Haul truck capacities have increased due to their economies of scale in large-scale surface mines. These high-capacity trucks impose dynamic loads on haul roads. A previous study estimated the dynamic forces imposed by ultra-large trucks on haul roads to be more than three times the static load. These dynamic forces exacerbate haul road stresses and deformation. Current haul road response models are 2D and use static truckloads for low-capacity trucks. No models capture the ultra-large truck dynamic effects on haul road structural response. This study uses 3D finite element (FE) modeling to compute the haul road response to ultra-large truck dynamic loading. The dynamic forces were modeled using multibody dynamics (MBD) in MSC.ADAMS. These forces were used in an FE model developed, verified, and validated in ABAQUS, to simulate the response of the haul road to the dynamic truck forces. The road was modeled using an elastoplastic Mohr-Coulomb model. The results showed that road deformation decreases with increasing layer modulus and increases with increasing payload. Increasing the base modulus from 100 MPa to 450 MPa reduced the maximum deformation from 258 mm to 62 mm. When the subbase elastic modulus increased from 100 MPa to 500 MPa, the maximum deformation decreased from 160 mm to 84 mm. Increasing the payload from 0 to 120% of the rated load increased the maximum wearing surface deformation from 131 mm to 216 mm. This study forms a basis for designing structurally competent haul roads for improving haulage efficiency and truck and operator health.

Jan 7, 2023

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade by the late 1990s, longwall mine output accounted for 40% of all underground output in the U.S. and today longwall mines account for approximately 50% of coal produced underground in the United states. A 51% increase in average shift production rates has occurred over the last 15 years. this increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust presents an ongoing challenge for coal mine operators the National Institute for Occupational safety and Health (NIOSH) conducted a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify the dust levels generated by major sources on the longwall section and to identify different control technologies in use today substantial reductions in dust levels were realized at sampling locations on the face when compared with ongwall surveys conducted in the 1990s results from the underground dust surveys and current longwall dust control technology and operating practices will be discussed. Mining Engineering, 2011, Vol. 63, No. 9, pp. 74-80. Official publication of the society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By C. J. Roos

Ground-engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these "consumable" items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corp. to predict the consumption of excavator teeth at a particular mine site. This paper presents the results of the Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2010

By Wern-Ping Nick Chen

Durability risks for underground facilities can be underestimated during design phase as compared to well-known geological risks. However, unclear durability requirements can result in construction schedule delay and change orders. Unlike bridges or buildings, a unified underground durability code or standard does not exist. This paper will provide a durability approach for underground facilities, including degradation modes, mitigations, and compliance measures during construction. In addition, this paper will address how to clearly specify durability requirements in a contract document to reduce disputes during construction and discuss key durability tests that are time consuming and will impact construction schedule if not timely planned.

Jun 23, 2024

By Richard J. Stoehr

In his time on earth, man has mined about 93.3 kt (3 billion oz) of gold. About one-half of this has been produced in the past 35 years. Roughly one-third of this gold is held as reserve in Central Banks. One-third held is in personal reserves. And one-third is held as jewelry or other fabricated products. The world per capita availability of mined gold is increasing. There are many forces shaping gold's future. Gold currently has a favorable exchange ratio. This is encouraging many new gold mining developments. Production is increasing and new recovery techniques are surfacing. The use of gold in the financial markets is increasing in some unique ways. And gold is again fulfilling its role as a universal money, making its future predictable. Gold Today Man is currently mining gold at the rate of about 1.4 kt/a (44 million oz per year). This adds about 1.5% of newly mined gold to the total supply each year. This production plays a small role in the pricing mechanisms since much of the 93.3 kt (3 billion oz) mined is available to the market in some form. The 31.1 kt (1 billion oz) held by central and international banking

Jan 11, 1984

By Xiaohong He, Qing Yu, Kaixiang Zhang, Rui Guo, Minghua Lin, Haoyu Miao

With the increasing depth of coal mining, the coal mine shaft traverses’ strata conditions become more and more complex. Shafts are often located in deep thick strata with unstable aquifers, and coal mining requires short-term rapid drainage of aquifers; the additional stress caused by aquifer water drainage is the direct cause of the shaft-lining failure. Over the years, many experts have conducted research on the shaft-lining damage caused by the consolidation and subsidence of the soil layer induced by the long-term drainage of the aquifer. On this basis, this paper conducts an in-depth study of the dynamic change of the pore water pressure of the aquifer in the short-term drainage and its influence on the response of shaft-lining strain and surface subsidence. The result shows that the Mandel effect of pore water pressure around the shaft-lining is obvious at the beginning of drainage, and the pore water pressure suddenly increases; the increase is independent of the drainage rate, which leads to the sudden increase of the shaft-lining strain value unrelated to the drainage rate. The result also shows that with the gradual dissipation of pore water pressure, the increase of shaft-lining strain is positively related to the drainage rate and negatively related to the drainage distance, and the variation trend of horizontal strain is greater than that of vertical strain, which appoints the main cause of shaft-lining damage.

Mar 16, 2023

By J. H. van Laar, C. S. L. Schutte, M. Le Roux

Highly energy-intensive systems prone to wastage are significant causes of unnecessary energy losses in industry. Deep-level mine chilled water reticulation systems fall within this category of inefficient energy-intensive systems. Some techniques (measured baselining, zero-waste baselining, leak detection, and control valves) exist to identify and reduce wastage in mine water reticulation systems. However, these techniques have not been compared, which begs the question of which is more accurate. A need, therefore, exists to compare these methods to determine the effectiveness of each. This study investigates each method and applies them to a case study mine, providing a platform for comparison. These methods identified wastage ranging between 2 and 20 l/s (3–30% of water consumption). The comparative effectiveness of the methods from best to worst was found to be zero-waste baselining, leak detection, control valves, then measure baselining. This study proposes an application procedure combining the considered methods to identify and eliminate wastage on deep-level mine systems more efficiently.

Jan 31, 2024

By Faruk Oksuz

The owners of large infrastructure projects are challenged on how to implement sound engineering and construction contracting strategies that address their prime expectations: a quality job, on time and within budget. With the increasing number of large engineering and construction projects worldwide, owners continue to search for alternative contracting strategies to address their risk, quality, sustainability (operability and performance), schedule, and budget concerns. Coupled with the shortage of resources, delays, political pressures, and other obstacles in procurement and negotiation processes, engineers and contractors are also looking for creative ways to optimize contract packaging strategies for efficient and successful project delivery. This paper compiles an array of decision making criteria and suggests a balanced evaluation, ranking and selection strategy in procurement of both engineering and construction services for large tunneling and other infrastructure projects. A number of owners? general preferences and viewpoints are discussed on large tunnel programs encompassing water and wastewater conveyance systems, pump stations and treatment facility upgrades. Contract packaging strategies and project phasing and segmenting alternatives for preliminary engineering, final design, construction management, and actual construction of facilities are featured for several large water and wastewater infrastructure projects. While the selection (and the relevant selection process and criteria) and performance of service providers, whether for engineering or construction, have profound effects on the outcome of any given project, this paper only examines strategies for con-tract packaging. More specifically, the authors evaluated case studies and developed a range of recommendations for packaging of large water and wastewater infrastructure projects with multiple components.

Jan 1, 2008

By Tim Neil, O&apos

Large is the applicable adjective here. The largest hydraulic shovel in the world, the largest copper mine in the world, the largest copper producing company in the world. The O&K RH 300 hydraulic excavator has been put into service to move overburden and mine ore at the Chuquicamata open pit mine of the Chilean state copper mining company, Corporation Nacional de Corbre de Chile (Codelco). A large shovel: Equipped with a 26-m3 (34-yd') rock shovel, the RH 300 is able to fill a 170-t (187-st) truck in three passes with cycle times of 30 seconds. A large mine: At present, the Chuquicamata pit is 4 km (2.5 miles) long, 2 km (1.2 miles) wide, and 520 m (1700 ft) deep from rim to bottom bench. The current 450 kt/d (496,000 stpd) of material mined will increase to 600 kt/d (661,000 stpd) when the expanded production rate is reached in 1989. (Chuqui Expansion details, p. 20). A large mining company: Codelco's total output from its two open pit and three underground copper mines is more than 1.1 Mt/a (1.2 million stpy) of copper. This makes Codelco by far the largest copper producer in the world. It accounts for about 15% of the Western World's copper requirements. Chuquicamata is located in the hot and arid Atacama desert of northern Chile. The mine is located 240 km (150 miles) northeast of the port city of Antofagasta. Mine elevation is 2700 m (8850 ft). Chuquicamata's known reserves of oxide and sulfide ores amount to more than 450 Mt (496 million st) of contained copper. There are also reserves of more then 1.4 Mt (1.5 million st) of contained molybdenum. Originally, Chuquicamata was a rail pit. The shovels loaded rail cars hauled by locis on tracks along the benches. During the 1970s, the rail transport was replaced by truck haulage. Crushing and conveying rock waste in the pit is the latest step in the continuing evolution of more productive and economical methods of materials movement. In 1990, the in-pit crushing plant will be in operation. The waste will be mainly transported out of the pit on belt conveyors rather than trucks. The system will incorporate a 9.6-kt/h (10,600-stph) semi-portable crushing station, a 14-km (8.7-mile) conveyor using 1.8 m (6 ft) wide heavy duty belts, and a tripper-spreader to stack the waste dumps. Since Chuqui went into production in 1915, more than 2.5 Gt (2.8 billion st) of material has been excavated. This includes nearly 1.7 Gt (1.9 billion st) of ore from which some 16.4 Mt (18 million st) of copper has been recovered. The Chuquicamata porphyry type ore body is an altered and fractured intrusive granodiorite or quartz-monzonite porphyry that carries the mineralization. The action of ground water on primary sulfide minerals in geo¬logic time has created oxide ores and a zone of secondary enrich¬ment. The oxides occur above the sulfide zone and are also mixed with the upper parts of the latter. At Chuquicamata, the current grade of 1.5% copper is expected to decline to about 1% by 1995. To maintain metal production at cur¬rent levels, it will be necessary to increase ore production rates by about 50%, as mentioned, to 153

Jan 1, 1988

By Jonisha P. Pollard, F. Nasarwanji, Lydia M. Kocher

This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1000 full-time employees, which is nearly double the rate of the next highest affected body part, the back.

Feb 24, 2022

By D. H. De Jager

Fluorapatite is an important constituent of the greater part of the basic and ultra-basic rock members of the Complex. The evidence for and role of primary magmatic processes in the development of concentric zones of dunite, pyroxenite, syenite and carbonatite and its consequent bearing on the distribution of apatite are discussed. The presence of at least two generations of each of the latter three rock types indicates the cyclical nature of magmatic activity. Pegmatitic-metasomatic phases corresponding to the major magmatic cycles resulted in emplacement of pegmatoidal assemblages. The abundance of apatite in the pegmatoid can be traced to the composition of its parent magma and its cooling history. Approximately 2.5 million tonnes of phosphate concentrate are produced annually from ores containing from 10 percent to 25 percent apatite.

Jan 1, 1978

By Rongjie Kong, Shiwei Wang, Dongjiao Gui

Metal cations have significant effects on the flotation of coal and minerals. In this study, the effects of monovalent cations ( Na+ and K+) on the flotation of low-rank coal (LRC) were investigated using flotation and particle–bubble attachment experiments and through X-ray photoelectron spectroscopy (XPS) and molecular dynamics simulations. Oleic acid (OA), methyl linoleate (ML), hexadecyltrimethylammonium chloride (CTAC), ricinoleic acid (RA), and kerosene were used as flotation collectors. The flotation experiments revealed that the flotation yields of LRC improved when OA, ML, RA, CTAC, and kerosene were used in pure deionized water. However, flotation was suppressed for these collectors in the presence of K+ and Na+ ions. In contrast, when using CTAC, the flotation yield increased in the presence of these ions. Specifically, the flotation yield increased from 41.24 to 87.03% when 2.0 kg/t CTAC was used in 10 mmol/L NaCl solution. Particle–bubble adhesion experiments and XPS revealed that the hydrophilic groups of CTAC were adsorbed on the LRC surfaces by electrostatic forces, whereas the oxygen-containing functional groups of OA, ML, and RA formed hydrogen bonds with the LRC surface in pure water. Finally, the simulating result revealed that the hydrophobic ends of the OA, ML, and RA collectors hinder the flotation of LRC by adsorbing monovalent cations, whereas the adsorption of monovalent cations on the hydrophobic end of the cationic surfactant (CTAC) promotes flotation via strong electrostatic interactions.

Jan 31, 2024

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

By C. L. Kosmoski

In recent years, coal mining safety has attained national attention due to several highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with 42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year (National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture,? and can be defined as the characteristics of the work environment (such as the norms, rules, and common understandings) that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to present the aggregated results from those five safety culture assessments conducted at underground coal mines. Additionally, some general recommendations for areas where coal mines might focus their attention as part of their attempts to improve safety culture are offered.

Feb 23, 2014

By Peter J. King

Demand for both lead and zinc to the year 2000 will be characterised by modest to nil growth in mature economies, with positive 3 to 4 per cent annual growth rates in developing nations. Asia and China will feature significantly in this growth. Overall lead demand is expected to grow about 1 per cent a year, with industry becoming more dependent on the fortunes of the automotive industry as the lead-acid battery will be the only major end use to expand. Zinc will become more dependent on its main use, galvanising, as the automotive and construction industries move to high levels of dependence on corrosion prevention. Strong growth in zinc consumption in S.E. Asia, China and India is likely to feature widespread development of the continuous steel strip mini-galvanising line technology. Thank you Mr. Chairman for inviting me to this Conference. As an Australian I am honoured to be here to offer some thoughts about future trends in metal consumption -- with particular reference to the role of countries in my own neighbourhood, the developing Asian nations, including China. It is customary for a member of the producer fraternity to speak to the topic of future development. This is no doubt due to the fact that our companies are so often engaged in endeavours to determine the future prospects of the metals as essential background to massive investment decisions relating to the development of new mines and smelters. This is sometimes also applied in relation to the more painful decision of closures of aging operations. In this paper I have drawn upon recent studies by AM&S into the future of lead and zinc. While this work has been thorough and skillful, we are nonetheless left with uncertainty on a number of counts. Firstly. predictions in the past in our industry have not been all that credible. Need I remind a U.S. audience for instance of the Paley ' investigation setup by President Truman in 1950 to study U.S. copper requirements for 25 years in the future. Asarco's Simon Strauss gave those of us daring to forecast long term commodity trends a salutary reminder that the Paley Commission with all the expertise at its disposal missed the mark in its copper predictions by a very wide margin indeed. Additionally, it is difficult to take comfort from longer term economic forecasts. Too many important economic issues remain unresolved suggesting considerable caution. These include the threat of growing protectionism; low economic growth rates with stubborn unemployment levels; and levels of government expenditure at near saturation as a percentage of GDP, to name a few. However, on a more optimistic note. we can look to China, where there appears to be momentum in its economic growth; oil, where stable oil prices to the mid 1990's will contribute to inflation control; and the fact that LDC debt, while still a major issue, is declining in importance and priority. In the short time allocated to us. I wish to deal succinctly with the lead and zinc raw materials supply picture, which is one I do not believe will hold too many surprises for this audience. Following the review of raw materials supply, we will turn our attention to the changes in the pattern of demand towards the year 2000. emphasising the Asian position. In this context. I would like to focus on the theme of the changes in OECD consumption levels relative to those of the emerging nations. One area we will be paying special attention to is China.

Jan 1, 1986

By Rameshwar Sah, Somasekhar Pitchika, Akhil Singh, Seenivasan Rajiah, C. B. Dayanand, G. Balachandran

In the sintering of iron ores, the partial substitution of anthracite coal for coke breeze has been considered to be an effective way of reducing emissions and improvement in sintering properties. In the present study, the combustion characteristics of the anthracite coal and coke breeze were investigated and its influence on product sinter quality and sinter flue gases is being monitored. Pot trials are carried out with different coke breeze ratios, 0%, 40%, 50%, 60%, and 100%. It is found that as the percentage of anthracite coal is increased from 0 to 100%, the sintering time decreased from 24 to 20 min, and the productivity increased from 2.25 to 2.60 t/h/m2. Up to 60% anthracite coal substitution Tumbler index (+ 6.3 mm%), Product yield (+ 5 mm%), and fines generation (− 5 mm%) is found 62.29%, 85.17%, and 15.33%; moreover, hematite ( Fe2O3), magnetite ( Fe3O4), calcium ferrite phases ( CaFe2O4, CaFe3O5), and Silico ferrite of calcium and aluminum (SFCA) are major mineral phases found during microstructural analysis of product sinter. Keywords Sintering · Anthracite coal · Combustion rate · Productivity

Jun 2, 2022