Search Documents

By N. Djordjevic

The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice - not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape.

Jan 1, 1997

By Garrett R. Hyde, Aleksandar Stojsic

Introduction Economic pressures in the international marketplace have spurred advances in almost every facet of flotation. New developments have occurred in flotation chemicals, flotation machines, and in the application of automated process control technology to grinding and flotation. Many of these advances are the results of concerted efforts to apply the knowledge obtained from basic flotation research over the past 15 to 20 years, to develop industrial technology for the more efficient separation of sulfide minerals in real ores. Mining company executives and equipment manufacturers are being called on to make decisions for incorporating some of this technology into present operations. This discussion is limited to two developments now at the stage of being engineered into industrial scale operations. They are control of the electrochemical environment or redox potential of the slurry, and control of bubble size in column flotation. Potential economic impacts are noted. Froth flotation Froth flotation makes use of differences in the surface properties of finely ground minerals to obtain separation. If the mineral surface is water repellent, the mineral particle will stick at the air-water interface of a bubble and float. If a mineral surface is not naturally water repellent, a chemical collector is added to the slurry to make it so. The collector must adsorb on, and make water repellent only the mineral to be recovered, not the gangue minerals. To achieve this degree of selective adsorption, chemical modifiers may have to be added to the slurry. Modifiers include pH regulators, activators, and depressants. Electrochemical control One of the most significant developments in recent years in the area of mineral processing technology is the recognition that collector adsorption of sulfide minerals is an electrochemical process. Consequently, flotation of these minerals depends on the electrochemical or redox potential of the system. Many of the modifiers used to control various flotation processes are actually potential controlling reagents. For example, the role of well known depressants, such as cyanide, sodium hydrosulfide, and sulfur dioxide, is essentially to

Jan 7, 1987

By James P. Sabogal

A control and monitoring system is being developed by Betz Laboratories for the heap leach process in gold recovery. Called Betz 14000GL, the system is designed to improve gold leaching and provide savings in chemical consumption by controlling and monitoring key parameters in the heap leach gold recovery circuit. The system uses information from on-line sensors to control antiscalant chemical addition, pH and cyanide levels. The proprietary graphics and report features of the computer system allows the user to monitor and critically evaluate the performance of the process.

Jan 1, 1998

By D. L. Slyter

Coeur d'Alene Mines Corporation's Thunder Mountain project in Valley County, Idaho, is one of the most remote active mining operations in the US. High altitude, heavy snows, and proximity to wilderness complicate operations in this environmentally sensitive area. Mining is conducted by conventional open pit techniques while processing utilizes on-off heap leaching and Merrill-Crowe zinc precipitation. The project is one of a few similar operations which detoxify the leached ore prior to its removal from the leach pads. Both leaching and neutralizing ( detoxifying) circuits are closed and independent loops. After leaching, alkaline chlorine solutions destroy residual cyanide in the heaps. Calcium hypochlorite solution for the cyanide destruction is prepared by injecting chlorine gas into milk of lime solution.

Jan 1, 1998

By David J. Collins

The emergence of activated charcoal adsorption as the most popular recovery method for precious metals, has led to numerous innovations aimed at increasing the efficiency of the process. This article describes a change in traditional charcoal transfer methods which will aid in reducing charcoal attrition losses. Studies have shown that significant charcoal attrition takes place during transfer, be it when using airlifts or centrifugal pumps. Tests conducted at Pinson Mines indicated a 4 to 8% loss to the minus 20 mesh fraction of charcoal after three (3) hours of pumping charcoal. Tests conducted while the author was at Jerritt Canyon indicated that charcoal transfer was a major contributor to charcoal losses; a decrease in the amount of coarse charcoal (plus 12 mesh) and an increase in the amount of finer charcoal (minus 16 plus 20 mesh) was noted as charcoal was moved to the head of the adsorption circuit.

Jan 1, 1998

By Ronald O. Harma

Iron ore pellets made from concentrates produced from low grade iron ores are the primary iron bearing feedstock for iron making in North American blast furnaces. Steelmakers are demanding increasingly higher quality to provide for improved blast furnace productivity, efficiency, product quality and environmental compliance. Unfortunately, this higher quality iron ore product must be produced from the vast deposits of low grade iron ores that are becoming increasingly poorer in quality with regard to mineral liberation and ease of concentration. Since some of these low grade iron ores require grinding to as fine as 90% -500 mesh (25 microns) for liberation and since more of the silicious gangue and other minor undesirable constituents must be removed to provide the higher quality, we have come to depend on flotation to do the added work. Flotation technology and other preflotation unit operations must improve to meet these increasing demands. In many cases, flotation equipment, reagents and circuit operating performance have improved little during the last two to three decades. Mechanical flotation cells have grown from 14 cubic meters (500 cubic feet) to over 84 cubic meters (3000 cubic feet) to help reduce capital and operating costs; however, flotation metallurgical performance has not improved, Column flotation has only recently shown promise in improving metallurgical performance for iron ore rougher flotation. Previous column flotation success was mainly in scavenger and cleaner flotation steps for treating minerals other than iron ore. Although some new flotation chemicals have been developed for removal of silica and other minor constituents under widely varying mineralogical scenarios, recovery of iron mineral has not improved. The operation and control of flotation circuits have become more challenging because of the increasing workload on flotation. Better sensing, process control and operation of flotation circuits are essential as we go forward. Iron ore upgrading by flotation can be classified into either anionic or cationic methods. Anionic flotation of either iron oxide or silicious gangue is accomplished by collector type, pH control and selective chemical activation . Similarly, cationic flotation of silica or iron oxides is accomplished by collector type, activation and/or pH control. Removal of other minor constituents is achieved by using specialty chemicals under controlled conditions for preflotation, co-flotation or post flotation steps. Generally, anionic flotation is used for floating cleanly liberating crystalline oxidized iron ores such as hematite, specularite and martite. Earthy and hydrated oxides such as hematite and geothite can be upgraded with either anionic or cationic collectors after controlled dispersion of slimes or prior removal of slimes. Anionic flotation of silicious waste can be achieved by calcium activation of silica. For magnetic iron ores small amounts of locked silica particles (middlings) can be removed by cationic silica flotation, which is the only method in commercial use in North America today. Historically the efficiency of these iron ore flotation processes has been restricted by the loss of fine iron particles (minus 500 mesh) to the tailings product. New technology is required to overcome this loss and improve overall flotation performance. Development of technology for more selective separation of silica and other minor undesirable constituents from iron ore will provide both quality and cost benefits to the iron and steel producers. Development of future iron ore production in North America will face stiffer technical challenges. These new and undeveloped iron ore deposits are largely oxidized (non-magnetic) and by nature contain more slimes and other undesirable constituents. Unless other new technology evolves, flotation will be the major treatment process required to upgrade these difficult low grade iron ores.

Jan 1, 1993

By Victor F. Hollister

Introduction Trends of successful discovery technology and psychology emerge from a thoughtful study of various companies' exploration programs. These subjective patterns can be generalized into groups of factors for discussion. Here, for convenience, factors that influence exploration success are separated into management and geologic concerns. Most successful discoveries have a demonstrably favorable management combined with a technically competent geologic input. Both are required. But the management input is decisive. Management factors include the correct definition of management's role; cost of exploration; time needed for exploration; commodity selection; and the fostering of autonomy, creativity, and confidence in the geology department. Geologic factors include imaginative technical competence (field as well as academic), correct development and use of empirical exploration or prospecting models, and dedication. Success comes to those entities that are properly managed and have technological competence. A management team that directs a company's business has been compared to a dynasty. The dynasty lays out policy and follows up with appropriate action. In that management's power is pervasive, the term is appropriate. Management's role is, however, more important. Many examples can be cited where the geologic input was impeccable. But management somehow snatched defeat from the jaws of victory, and the exploration success was turned to a third party's profit. Management Factors Management's role can be broadly generalized to four parts. These are to identify the commodities it seeks, define its part in the exploration process, develop a functioning exploration department, and have the desire to succeed. It must have confidence in its geologists and delegate to them the authority and responsibility they need to operate successfully. Head office management cannot do the thinking for a field staff thousands of kilometers away. There is no substitute for confidence and delegation of authority. Successes came to those who had the freedom to act. Motivation is a management requisite. Management's role is to prevent destructive, internecine political battles within the corporate structure. Most large US mining corporations have well known histories of political strife that have damaged their exploration efforts. Management's role must, above all, include the desire to succeed. There are cases where management has been confronted with a commercial exploration success, but their reaction is to request additional study or exploration. Perhaps the problem of bringing a commercial find into production is beyond their capabilities. But a bona fide discovery sent back for additional work commonly is lost due to that management. The cost of exploration is a factor that management must accept. A variety of studies made during the past 40 years shows the cost per discovery to be $25 million, $38 million, $200 million, or even $290 million. These figures are derived by dividing the total exploration expenditure by the number of discoveries. However, successful management dynasties have a much lower cost per discovery during their management regime. Asarco, from 1948 through 1963, had one of the lowest cost discovery rates in the world. Duval Corp., from 1948 through 1968, had comparably low discovery costs. Placer Development, from 1955, was equally successful. Western Mining in Australia has had one of the longest lived dynasties associated with exploration success. Time is vital in exploration success. Most successful exploration case histories stress sufficient time in project exploration so that the target is well tested. A large target cannot always be adequately evaluated by a few holes (strat or concept testing). Serendipity helps in exploring large targets, but it best operates in a lengthy program. Numerous case histories include pleasant surprises. But these came mostly after the 10th hole. Commodity markets are important factors governing exploration success. Management's decision to explore for a specific commodity can doom its effort if that product suffers from severe oversupply. Unquestionably, progressive copper price increases from 1948 through 1968 helped convert marginal porphyry copper discoveries

Jan 8, 1985

By Bryan A. Bartley

High intensity, autogenous grinding has been developed in the hard rock, quarry industry and is finding wide application in mineral processing. The autogenous vertical shaft impactor is described and action within the machine is illustrated. This machine is compared with the cascade mill, in the three characteristics of impact, inter-particle rubbing and nipping, of which impact is the most important. There is a seven fold increase in impact level over that of the cascade mill. The autogenous impactor has characteristics of crushing and grinding, preferential crushing, abrasion resistance and drying. These are illustrated by examples of industrial applications, where the machine is now used and range from abrasives, such as Carborundum to phosphate rock.

Jan 1, 1998

By Peter Zhang, Daniel Su, Bo Kim, Berk Tulu

This paper summarizes significant findings from the ongoing NIOSH Gas Well Stability research over the past decade; in particular, the important ground control engineering considerations. Longwall-induced surface and subsurface deformations may induce gas well casing deformations and stresses, depending on a few parameters such as overburden depth, overburden geology, topographic relief, strata dip, gas well setback distance, and a gas well casing cementing alternative. Overburden depth to the mining seam is one of the most influential factors; shallow overburden depth induces large horizontal displacement and resulting casing deformation and stress, while deep overburden depth induces large longwall-induced vertical pressure. Overburden geology is another important factor affecting the longwall- induced casing deformations and stresses; the large contrast of bending stiffness at the soft-to-hard rock interfaces tends to induce large casing deformations and stresses. Large surface topographic relief and the presence of soft-to-hard rock interfaces below the stream valley bottoms may shift longwall-induced subsurface gas well casing deformations closer to the surface, thus having less impact on underground. mining operations. Strata dip magnifies longwall-induced deformations by 20% per degree of strata dip for down dip longwall excavations. The gas well setback distance is also a critical geometric parameter; the effect of longwall-induced deformation decreases exponentially as the setback distance increases. Longwall-induced casing deformation and stress will be mitigated or totally uncoupled for uncemented production casing.

Jun 25, 2024

By G. M. Wali Ullah, Micah Nehring, MEHMET KIZIL, PETER KNIGHTS

In operations that use the sublevel stoping mining method, production scheduling takes into account factors — including ore reserve envelopes, ore grade averages, equipment capacity, feed controls to the mill, and geotechnical restrictions — across the scheduling horizon. Mathematical programming is one of the most effective methods for enhancing the decision-making process in regard to the most viable production schedule in light of a given set of limitations. The majority of research on sublevel stope mining focuses primarily on a single objective of optimization, which is to maximize the net present value (NPV). Environmental, social and governance (ESG) considerations are becoming more prevalent in the mining industry. This includes aspects relating to deforestation, land disturbances, gas emissions, community relations and water usage, among many others. Institutional and other kinds of investors are becoming more interested in the work that resource companies do regarding their ESG obligations. This review article identifies the gap in the existing literature and proposes to simultaneously optimize the production schedule around three objectives. Two of these relate directly to ESG aspects

Jul 1, 2024

By Larry Lynott

This paper summarizes the benefits ofusing an in-situ analyzer in a sampling and valuation program. The tests and studies cited quantify the problems associated with current conventional sampling techniques and contrast conventionally-obtained results with those obtained through in-situ analysis. Data are presented to show the improved precision in valuation resulting from the in-situ method. Greater precision in estimating the mineral content of unmined ground becomes increasingly important as mines strive for optimum exploitation of their deposits. As the following analysis shows, the variable distribution of minerals within a deposit, along with the difficulty and the cost of high density sampling limits the precision which is currently possible in practice. An inherent problem exists in the conventional method of sampling. The erratic values of ore grade necessitate the collection oflarge numbers of samples for statistically accurate valuation and ore reserve estimation. Owing to the cost of manpower, current sampling techniques do not allow for the collection of sufficiently large numbers of samples. The most common method of sampFng in current practice is chip sampling, although bulk sampling is sometimes used. The intent of sampling is to obtain an estimate of the value of blocks of ground prior to mining. This information is used to plan the rate and sequence of mining, yet the sampling intervals which are possible in practice cause these block estimations to be ubject to considerable uncertainty. This inevitably leads to mcorrect mining decisions which may be vy costly.

Jan 1, 1998

By M. G. Skowroski, G. G. Eichholz, J. P. Ambrose

Introduction It has long been known that there are extensive deposits of phosphate-bearing deposits in the Coastal Plain of Georgia in many locations that are similar to those being mined commercially in central Florida. A major drilling program was conducted in 1966-67 by the Georgia Geological Survey (GGS). The economic potential of some of the material uncovered was evaluated at that time by a team at Georgia Institute of Technology led by Dr. J.E. Husted. There were some promising results. Since then, there has been little commercial interest in pursuing this matter, though the potential for development remains. In the long term, Georgia's phosphorite deposits could be a major source of income to the state if they were commercially processed. Phosphorite deposits contain significant levels of uranium and thorium. Uranium concentrations in Florida phosphate aggregates have been found to be 120 to 140 ppm. The presence of high concentrations of uranium means that there is a small but finite concentration of radium, which subsequently leads to radon gas emanation. It is the radon emanation and its progeny that may pose the largest health problem in many types of mining. Surface mining operations can possibly elevate the radon and radon daughter concentration in the vicinity. There is always some public concern whether any increase in the radon concentration in the atmosphere by mining (surface mining in the phosphorite case) could elevate the risk of cancer in the nearby population. At the present time, a great deal of attention has been devoted to the possible health effects of radon and its decay products in the inhaled air in mines and inside buildings built on mill tailings or uranium-bearing rock (Gesell and Lowder, 1980). Several evaluations have been published on the potential health effects of the Florida phosphate operations (Guimond and Windham, 1975; Roessler et al., 1980; Travis et al., 1979) and for buildings incorporating phosphate slag aggregates (Kahn, Eichholz, and Clarke, 1983; Roessler, Roessler, and Bolch, 1983). They all indicate that such potential effects are small, but tangible, compared with other radiation effects, for instance in the nuclear industry (Cohen, 1981). In view of the current concern, especially by the US Environmental Protection Agency (EPA), with the radiological consequences of large-scale mining of uranium-bearing phosphate rock (Guimond and Windham, 1975), it was decided to assess the potential radiological consequences if the Georgia deposits were developed. This paper presents an attempt to estimate the magnitude of any radon-based health effects that might arise from future mining operations in selected areas of the Georgia coastal region. To do this, a calculational model was developed that took into account the mining operations themselves, the atmospheric dispersion of the radon released, and the radon daughter concentrations in nearby towns. The model was applied to both extremes. The first application was a hypothetical mining operation in Echols County. Echols County is very sparsely populated and, unless living very close to the site, a person would probably experience little radiation exposure, if any. The model tries to prove this point. The second application was at a site near Savannah, Georgia. Both sites contain economically feasible phosphorite deposits and were not entirely hypothetical in that sense. Site selection In the course of the South Georgia Minerals Program (Furcron, 1967), an extensive series of drill core samples had been collected from various mineral occurrences in the coastal plain. It was found that the cores from the previous drilling program (Furcron, 1967), though carefully preserved, were not readily accessible. But the GGS reports did contain gamma logs of all the holes surveyed. With the cooperation of Dr. Neal Shapiro of the Survey, some core samples were selected and assayed, and used to calibrate the gamma log data. Samples from locations known to have detectable radioactivity were screened and counted. Their measured uranium content was used to calibrate the gamma log profiles for those same holes as obtained by the GGS. On this basis, two of the higher-level sites were selected and the calibration was used to obtain integrated uranium concentrations over the length of the borehole. It is customary to describe radon and radon-daughter concentrations in "working levels" (WL), where one WL represents a concentration of radon daughters capable of releasing 130 000 MeV of alpha particles, equivalent to 100 pCi of radon in equilibrium with its daughters per liter of air. A representative concentration is 0.15 WL, below which radon levels are widely considered to be negligible. For the mine sites selected, the surface area and rock volume were determined to estimate their radon content. Working-level values were then estimated for the assumed radon release from the crushed ore and the exposed surfaces of the mine pit. According to Kisielewski (1980), 93.4% of all radon released from open-pit operations is released from the ore zone; thus, the calculations assumed that those surface areas were the main sources.

Jan 1, 1987

By O. A. Bascur

The problem of setting the proper control objectives and/or having several objectives to be met in the implementation of grinding control strategies can be resolved. The design and implementation of a distributed control system for safe operation of a grinding circuit while maximizing profit is presented. An optimal recovery/throughput target for a desired grind is accomplished by advanced control strategies at the DCS level. A mill load constraint control technique provides stable operation with a substantial increase in throughput, while the desired grind index is maintained by an inferential grind control technique without using a particle size analyzer. The integration of crushing/grinding and flotation in the overall design was the key to the success of the project. This synergistic effect was obtained by implementing a computer -plant management system in the concentrator. The overall philosophy of keeping the implementation simple but not simpler was used.

Jan 1, 1989

By James R. Arnold

Over the past few years several commercial wetting agents and drying aids have been tested in the lab and in the plant at Gold Fields Mining's operations at Mesquite and Ortiz. The major goal was to increase recovery with these surfactants by improving the permeability of the pad and increasing the rate of penetration through the rock.

Jan 1, 1988

By Roy M. Fleming, Christine B. New

The federal standard for limiting exposures to miners from radon daughters was reduced from 12 working level months (WLM) per year to 4 WLM per year in 1971. However, even at that time some researchers were concerned that the new limit would eventually be shown to result in an excess risk for lung cancer mortality in miners. The National Institute for Occupational Safety and Health (NIOSH) is now engaged in a comprehensive review of this topic. As the lead agency in this project, NIOSH has developed a work plan and established a work group to implement this plan. The procedure and specific considerations are outlined in the work plan for developing a comprehensive ionizing radiation standard recommendation for all miners, underground and surface. Such a recommendation will not only include estimates of health risks at various levels of exposure, but also appropriate recommendations for medical monitoring, sampling and analytical methods, sampling strategies, posting, engineering controls, personal protective equipment and recordkeeping. The work group has twenty-four members. Eleven members are NIOSH personnel representing six divisions of the Institute. The remaining thirteen members represent other federal agencies, specifically the Bureau of Mines of the Department of the Interior, the Mine Safety and Health Administration and the Occupational Safety and Health Administration of the Department of Labor, the Office of Radiation Protection of the Environmental Protection Agency, and the Bureau of Radiological Health of the Food and Drug Administration, Department of Health and Human Services. Several factors contributed to the decision to initiate this project. First, the efficacy of the current standard was considered. An initial study group was formed in the spring of 1980 by NIOSH to identify and evaluate articles that contained information on lung cancer mortality risks at and below the present permissible exposure limit. The conclusion drawn from their evaluation was that a two-fold excess risk of lung cancer mortality at and below 120 cumulative working level months (CWLM) of exposure to radon daughters is evident. This composite indication from selected studies was of sufficient magnitude to justify further evaluation. The study group, however, recognized that other studies and information must also be considered in a quantitative risk assessment which would form the basis for recommending an acceptable and feasible permissible exposure limit. A second factor in the decision to pursue further evaluation was the gaps in the current standard that had previously been identified by the Mine Safety and Health Administration (MSHA). These included lack of medical monitoring of underground miners and absence of regulations for surface miners. The seriousness of the health hazard relative to other hazards in mining was also considered. Along with exposures to silica and asbestos fibers, radiation was judged to be one of the major health hazards in mining, These combined factors constituted the justification to develop criteria and recommendations for improved mandatory health standards. The development process begins with a survey and review of the available world-wide information on the topic, including data and information developed by NIOSH. The end product of this review is to be a document that will contain an evaluation of the collected information and support for any recommendations that are made. To develop this document, the present work group has been divided into five task groups with the following emphases: Health Effects, Medical Aspects, Monitoring, Environmental Exposures, and Engineering Controls and Work Practices. The Health Effects task group is to evaluate the evidence from epidemiologic and animal studies of adverse health effects associated with all forms of ionizing radiation encountered in mining and milling operations. The "weight-of-evidence" of the results of all relevant and useful studies will be summarized, with the reasons for emphasizing the cited studies. The critical cells or tissues and the factors that should be considered in estimating the dose to these areas from various types of radiation will be identified. An evaluation will be made of the possible impacts of smoking and exposure to diesel exhaust on the determination of health effects related to radiation. The implications of biologically redundant dose in terms of the time between tumor initiation and death will also be analyzed. The Medical Aspects task group is to review the generally-accepted and the state-of-the-art medical technology for the detection of adverse health effects from ionizing radiation exposure. An evaluation will be made of the accuracy of urine and fecal analysis, wholebody counting, chromosome analysis and nose blows, as well as their usefulness for early detection of adverse health effects. Early detection is of little utility to the affected individual unless subsequent medical care can improve the prognosis. Recommendations for screening tests will be made after carefully considering the accuracy of the diagnostic procedures and the usefulness of early detection. Required recordkeeping and transfer rights will also be addressed. The Monitoring task group is to consider the state-of-the-art technology for the monitoring of occupational radiation exposures. Instrumentation, sampling strategies and analytical procedures will be reviewed for both personal and area sampling. The implications of the associated levels of confidence for non-compliance decisions will be evaluated. The discussion will also include an evaluation of the feasibility of replacing present monitoring systems with recent technology and the impact that a possible lower permissible exposure limit would have on monitoring requirements. The Environmental Exposure task group is to investigate the field procedures and mathematical methodologies which have been used to quantitate exposure levels to the various kinds of ionizing radiation. The magnitude and direction of the possible biases in past exposure assessments will be estimated. Specific attention will be given to the controversies concerning the quantification of the biological dose equivalent and the feasibility of recommending standards for mixed radiation exposures which use "rem" as the unit of measurement. The Engineering Controls and Work Practices task group will analyze the advantages and limitations of

Jan 1, 1981

By A. Ghalambor

The objective of this investigation was to determine the sensitivity of three selected input parameters in the operational control of continuous bottom-fed thickeners used for the treatment of coal refuse slurries. The three variable parameters were "Feed Flow Rate," "Feed pH," and "Feed Solids Concentration." These three input parameters were studied under three polymeric conditions which were cationic polymer, anionic polymer, and a combination of cationic-anionic polymer. For each polymeric condition, two mathematical models were developed: one for overflow response, the other for underflow response. The combination polymers produced the best desired quality of overflow and underflow. For this polymeric condition, changes in the feed solids concentration was the most sensitive factor in the maintenance of the overflow quality, and the feed pH was the most sensitive factor for the maintenance of the underflow quality. The mathematical models generated a set of plots which would allow an operator to control and/or adjust any of the three variables to achieve optimum conditions.

Jan 1, 1989

By B. J. Arnold

Over 600 million tons of coal are handled annually for use by the country's coal-fired power plants. Coal is transported in various ways. overland conveyors. Railcars, trucks, and barges. It can travel short distances or thousands of miles, picking up moisture, freezing, or drying. When the coal is received at the power plant, environmental problems with fugitive dust and further handling problems can arise.

Jan 1, 1989

By D. D. Lauriski

The Mining Division of Utah Power and Light Company is located in the coal fields of southeastern Utah -main office in Huntington, Utah. The Division will produce 6.5 million tons of low sulfur steam coal in 1988, making UP&L the largest underground mining operation west of the Mississippi. Coal is mined from three underground mines utilizing continuous miner and longwall mining methods. All coal produced by the Mining Division is utilized at UP&L's two largest steam-electric power plants, the Hunter and Huntington plants with a combined capability of 1,995,000 Kw. At UP&L we believe that to achieve success a company must have clearly defined goals which are understood, communicated and shared at each level of operation. We have also found from experience that a safe operation is generally an efficient and productive operation. As a Division, we have established a goal to achieve the safest, most efficient operation in the country. This is an ambitious goal. To achieve such a goal requires real commitment and a safety/training program capable of achieving needed results. The following is an overview of the program we have established at UP&L which has enabled us to reduce our accident frequency rate from over 40 in 1980 to 8.00 at present, as illustrated in Figure 1.

Jan 1, 1989

By Duk-Won Park

Since geologic anomalies are one of the governing factors of instability of underground openings, it is extremely important to know in advance the locations and extent of these anomalies such as faults and weak zones. At an underground coal mine in the Black Warrior Basin, core drilling was conducted to find a fault in an area where they were planning to locate longwall panels and possibly a shaft. Core logging did not provide sufficient information to delineate the exact location, strike, and dip of the fault. However, a high resolution reflection seismic study successfully solved this problem. This experience proved the seismic exploration technique could be used for premining coal exploration by reducing drilling costs and providing more accurate and detailed information about geologic anomalies.

Jan 1, 1988

Research has determined that ground control interaction problems in mining over a previously mined seam occur primarily in the tension zone created at the edge of the subsidence trough, and in areas above lower seam remnant pillars. Based on empirical and analytical studies, planning options for improving conditions on the upper seam have been developed to optimize extraction while minimizing the negative effects of seam interactions. These options include prediction of potential upper seam damage, guidelines for minimizing inevitable negative interaction effects, and recommended opening and pillar sizes, shape, and orientations, as well as design and planning procedures.

Jan 1, 1988