Search Documents

By J. R. Woolsey, B. G. Noakes

A prototype remote placer drill (RPD) has been designed and successfully tested in the offshore gold district of Nome, AK. The RPD system is unique in its design and in the cooperative support that was provided during its development by industry, academia and government. The RPD was conceived as a low-cost, rapid drill sampling system for the reconnaissance of marine precious metal placer deposits. The drill functions as a counter- f lush system. It incorporates a dual wall casing and a rotating percussion bit driven by way of a drill rod through the central eductor casing by a heavy duty pneumatic rock drill. The cost of drill sampling in the exploration of marine precious metal placers has traditionally been high due to the technical difficulties imposed by the environment and the remoteness of the sampling target. The objective was to reduce capital and operating costs of a drilling program through the development of a portable system incorporating drill compoments having a high power-weight ratio that could be deployed from work vessels of opportunity. A principal design requirement was to operate the system remotely from the sea floor with only flexible connections to the surface. This includes cable for deployment and retrieval and hoses for air supply and sample recovery, thus making the drill system semi-independent of the vessel's sea-induced motion. The prototype RPD underwent full operational test off Nome, AK in late summer 1988. It was deployed from the landing door of a modified LCT vessel, and rigged for a single pass of 5 m (16.5 ft). More than 50 holes were drilled in a wide variety of bottom materials typical of the off shore Nome submerged beach placers. The prototype RPD proved to be an overall success, recovering representative samples throughout the section in all but the heavy boulder ground. Compared with a conventional drill system on board that was assigned to a production drilling system, the RPD was capable of reliably sampling moderate ground less than 6 m (20 ft) in thickness, using a smaller crew and operating in higher sea conditions.

Jan 1, 1991

By Michael T. Ballard

The key to productive computer usage is system software integration with full compatibility among individual components. The majority of software developers in our industry are still in the process of perfecting individual components. As a result, exchange and validation of data between disciplines becomes an arduous process. We at Morrison Knudsen Engineers, Inc. (MKE) have integrated an entire system, allowing exploration, geology, modeling, mine planning, and operation modules to work as a single, complete system with direct exchange and validation of data. The importance of integration to both developers and users of today's mining soft- ware is becoming increasingly apparent as we, an industry, move toward growth and enhancement of the technology of ore reserve acquisition, evaluation, and management. It is also important to understand the present state of integration and where it is leading US. Not long ago, another industry passed through the same stages we are now setting up for the mining industry. The stereo industry began with a few individual components, the record player, tape recorder, and radio. People were able to play records, listen to the radio and record conversations and music only through microphones on their tape recorders. Soon, one enterprising individual discovered he could tape sound directly from the radio or record player by capturing audio output from the speaker wires. Interfaces and patch cords were developed, providing a means to transfer audio information between components with not only little loss of sound quality, but also the elimination of back- ground noise. The industry took another step forward with the introduction of "integrated" stereo, where the components were packaged in one cabinet with shared resources. This reduced overall cost which paved the way for better quality. Today's stereos are now so well integrated that many of the components share data and resources from the same manufacturer, designed to work together for almost perfect data transfer between any of the components. The result is better sound, convenience, and reduced cost. This is the ultimate goal for integration. Any system development passes through these same steps on the road to total interaction. Initially, the components are designed, tested, and marketed individually, often by separate companies. As the users become familiar with the components, the need arises for an automatic interface between the components. This is necessary to cut down on error during data transfer and to eliminate the redundant work required to enter results from one component into the next component in the system. As a result, interfaces must then be developed to aid in this data transfer. After data transfer is accomplished, the next step is resource sharing. Resource sharing is careful design and engineering by either cooperative, individual manufacturers or one firm taking on the task to produce a single package product. Design and resource sharing leads to lower overall cost, while still providing component capability with options to grow as the user grows. The mining software industry has been working to develop some very high quality component software and has indeed accomplished this task in every aspect of the mining industry. However, realizing the importance of integration, some companies with limited individual resources have started working together to interface their individual components. Other firms have undertaken the project of developing complete, integrated systems.

Jan 1, 1987

By Kenneth N. Han

The authors investigate the use of froth flotation to remove carbonaceous material from Carlin gold ore. They also study the effect of type and concentration of various oils as flotation collectors and of sodium silicate as the dispersion agent on the overall recovery of carbonaceous material. And they examine other variables affecting froth flotation efficiency, including particle size, pH of the solution and temperature. Han and Chen also investigate the effect of reduction and oxidation of carbonaceous material on froth flotation efficiency. This investigation showed that aromatic type oil was the most effective collector. And the authors also found that oxidized carbonaceous material was difficult to float unless the oxidized portion was subject to reduction before flotation.

Jan 1, 1990

By Stephen Navin, Pablo Ferradas, Carlos Silvestri, Alexander Markov, Jon Kaneshiro

In the high Andes of Peru, two tunnels are being constructed totaling nine kilometers in length at an elevation of over 4,500 meters. The tunnels convey freezing and crystal-clear waters from rainfalls, streams, and lakes for the consumption of Lima. The drill and blast 3-meter wide by 4-meter high tunnels are being driven from both ends through folded and sheared volcanic tuff, andesite, agglomerate,and limestone, where groundwater inflow is high. This paper describes the design geological and groundwater inflow investigations and construction.

Jan 1, 1999

By K. D. Allen, M. J. Blattman

The problem of measuring the amount of rock removed during a given time interval is faced by most mining operations. Many methods have been developed with varying degrees of success, dependent upon the mining method and the availability of usable data. The Rosebud Mine has been in production for nearly two years, employing several techniques to estimate monthly production from underground production stopes. The use of three-dimensional solids generated from survey data has greatly improved the reliability and confidence of monthly production reports. The authors will summarize the methodology currently being utilized at Rosebud.

Jan 1, 1999

By F. Wendling, G. M. Peixoto, J. A. M. Cano

A brief introduction is made on the existence of sulfides in the top gas of the Midrex Shaft Furnace, giving consideration to the operation of the furnace and the liberation of sulfur, as well as its consequential effects on the reduction process. The text shows a study of sulfur distribution in the pellet, emphasizing the importance of this distribution in relation to the liberation of sulfur during the reduction. A study was made to determine the sulfur compounds that exist in the pellets, showing ways of controlling the sulfur distribution and reducing its liberation during reduction.

Jan 1, 1991

By Terence H. Fisher

The use of more productive mining equipment, the tendency to longer development and the advent of new mining methods have introduced new challenges to the ventilation practitioner in Western Australia. These new and more productive mining methods have presented specific ventilation problems, that if not properly addressed, present additional hazards to miners. Factors influencing the increased hazards are larger diesel units, the use of series ventilation systems and an increasing incidences of long (single entry) development and production headings where miners could be trapped in a fire emergency. This paper discusses these new ventilation safety challenges, how they have been and are being addressed, and the legislation changes that take cognisance of technological developments.

Jan 1, 1995

By F. J. Susko

The US Bureau of Mines is using Fourier-transform infrared (FT-IR) analysis to investigate the bonding mechanisrn that occurs during the dewatering of clay slurries. High-molecular-weight polymers are used as flocculating agents in these processes. This investigation presents the results of an FT-!R study of calcium-exchanged montmorillonite treated with polyacrylamide (PAM) and polyethylene oxide (PEO). Both thin film and attenuated total reflectance (ATR) spectroscopic techniques were employed to study this clay polymer system. Results suggest PAM is adsorbed to the clay via the nitrogen atom of the polymer. A waterbridge is involved in the bonding between the clay at d PEO. Evidence also suggests that PEO may be adsorbed directly onto the surface of the clay.

Jan 1, 1991

By C. L. Barron, M. L. Smith, K. A. Prisbrey

SAG mill throughput is often a bottleneck to increasing plant productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility, which is also related to the rock fragmentation that is achieved by blasting. The relationship between the size distribution and fragility of the feed and the mill's product and the critical size in a SAG mill is examined.

Jan 1, 1994

By J. R. England, W. J. Taylor

The Sudbury Basin is the scene of the mining operations of the Ontario Division of the International Nickel Company of Canada, Limited. Around the rim of the geological formation and within thirty miles of the City of Sudbury are located twelve operating mines and one open pit operated by the Company. The City, with a metropolitan population of some 100,000 lies 240 miles Northwest of Toronto. In addition, there is one mine in Northwestern Ontario, at Shebandowan, 700 miles Northwest of Sudbury. In 1973 these mines produced 16.5 million short tons of ore of which 14.9 million tons were from underground and the balance from open pit operations. Mining methods include blasthole, sublevel caving, induced caving, shrinkage, cut-and-fill and undercut-and-fill. Raise boring commenced at Inco in 1964 and is now applied at all mines in the Sudbury District (Figure 1). [ ]

Jan 1, 1974

By R. Mohr

Storm water runoff from mine facilities such as haul roads, waste disposal sites and ore bodies have become recognized as the primary facilities associated with non-point source drainage. Depending on the ore body, facility design and geographical setting, nonpoint source drainage can cause pollution impacts to local surface and ground water resources. Non-point source impacts from surface mine drainage have become an important regulatory issue for the mining industry. Implementing non-point source drainage control plans that prevent impacts to water resources can be accomplished cost-effectively with moderate labor requirements. Design considerations for plan development must incorporate parameters including contributing drainage area size, slope, flow velocity, vegetation characteristics and soil scour velocities. The success of non-point source drainage and erosion stabilization planning is based on implementing control measures that dissect drainage patterns, reduce flow velocities and disperse runoff towards sediment control sites. Interim and long-range drainage control measures should begin during exploration activities. Regulatory legislation addressing non-point source pollution sources was enacted as amendments to the Clean Water Act (CWA) in February 1987. The legislation required states to initiate non-point source pollution control programs.

Jan 1, 1991

By David M. Miller, Pramod C. Thakur, Larry D. Taylor

The most common technique used to suppress respirable coal dust in air is that of spraying with fine water particles. The water droplets are typically much larger than respirable dust particles and they collect dust particles mainly by interception. Dust collection efficiencies can be improved by reducing the droplet size and in- creasing the droplet velocity. This is typically done by reducing the surface tension of water and increasing the water pressure. Dust collection efficiency can be further improved by in- creasing the electrical attraction between the water and dust particles through electrostatic charging. A technique developed by Conoco accomplishes both surface tension reduction and electrostatic charging by discharging weak solutions of surfactants in water at high pressures, 13.8 to 27.6 MPa (2000 to 4000 psi) in an intrinsically safe manner. The paper de- scribes the process and presents related dust suppression data.

Jan 1, 1986

By R. P. King, M. K. McCarter, K. S. Free

Mine plans typically consider the profits and costs associated with extracting and processing minerals into marketable products. Interrelationships between mine and mill costs are often overlooked during the process of mine plan optimization. A simple and quick method for predicting milling costs for a given block would improve the planning process, especially if the procedure could be incorporated as part of routine ore grade analysis of drill core or cuttings. Incorporating milling costs as part of the mine planning process could improve overall optimization of the mine/mill combination. A method developed by the Utah Comminution Center (UCC) at the University of Utah provides a possible answer to the need for quick and reliable grinding cost estimation (King et al., 1996). Using results from single-particle impact tests, a work index, called the Utah Load Cell Work Index (ULCWI), is calculated. The potential for routine use of the new method is explored by comparing ULCWI values with corresponding Bond Work Index (BWI) values for eight mineral materials (Free, 2000).

Jan 1, 2004

By J. A. Herbst, A. E. Oblad, Y. C. Lo

The major cost in comminution is energy consumption, which can be as high as 50% of the operating cost. Improvements in plant operations have resulted in up to a 15% reduction in energy usage (kw-hr/t). These improvements have been made through the optimization of grinding efficiency and the use of expert model-based control systems. Optimization involves the determination of the levels of the critical-operating conditions that result in the most efficient breakage of ore in the mill. These optimal levels are identified through plant/laboratory test work and through computer simulation using advanced process models. Model-based expert control achieves the maximum performance from the grinding circuit by identifying the characteristics of the ore in the mill with an optimal on-line estimator. Using this information, the control system dynamically determines the operating point that will yield the optimal performance. Two industrial applications of grinding-circuit optimization and model-based control are presented to demonstrate the power of this new technology.

Jan 1, 1997

By Eugene F. Casey

As indicated on the official conference program, this presentation in not a formal one, but a synopsis of the activities of a newly created Sub-committee of the Research Council on Underground Construction, which involves itself with small diameter tunnels. Because there is a dire need to develop a system of excavating small horizontal openings at shallow depths without interrupting traffic, it was hoped that a more progress report could be reported at this time. Because of ecological and environmental considerations, laws are being passed which mandate that all utilities be placed underground. In urban areas the excavation of trenches in which these utilities are placed has been done by disrupting the normal flow of traffic, thereby creating complete chaos. In addition, it always seems that the Companies involved have no coordination, since one company completes its installation and another one begins. Certainly, utility tunnels can be driven at greater depths to house main feeder and trunk lines, but there still remains the problem of installing distribution lines for house services. The definition of a "mini" tunnel, is a tunnel whose excavated size is approximately 48 in. or less. The objectives of the Committee are to "stimulate the development of systems and equipment to build tunnels in these size ranges which will reduce costs, time and surface disruption from current systems."

Jan 1, 1974

By David J. Herzog

There are two steps in evaluating potential mine waste impacts on ground and surface waters. Characterize the mine waste (characterization methodologies) and assess potential impacts (assessment strategies). One or both may be required for mine permitting, operation and closure. The first step is to characterize the waste. Determine if it has the potential to release chemical constituents or acid rock drainage to the environment. If no potential exists for release to the environment, the evaluation process is complete. A monitoring plan is then established. If the potential exists for release of chemical constituents or acid rock drainage to the environment, a strategy to evaluate potential impacts must be implemented. Strategies discussed here to evaluate potential impacts were developed during investigations at precious metal and base metal mines in Nevada. Water resources in Nevada consist mostly of ground water. So the strategies discussed focus on potential impacts to ground water. However, several of these strategies also apply to assessing potential impacts to surface water. Implementing these strategies has helped determine the potential for impact and has been successful in permitting mine expansion as well as allowing continued operation and obtaining mine closure at several mine sites in Nevada. These strategies were carried out in accordance with Nevada Division of Environmental Protection (NDEP) regulations and through the National Environmental Policy Act (NEPA)

Jan 1, 1995

By Maynard Stenberg

Judging from the progress made in August 1989, drilling and raise boring of a 400-m (1312-ft) pilot hole at the Elura mine of Pasminco Ltd. in Southeastern Australia, an observer would never guess that the project had been delayed nearly a year. Moreover, two pilot holes had been abandoned in previous attempts. The challenge was to drill a 93-mm (3.66-in.) H size exploration hole between Elura's 400- and 800-m (1312and 2624-ft) levels. The hole needed to be kept within a 300-mm-diam (12-in.diam) target cylinder over the 400 m (1312 ft) distance. The deviation restriction of the initial core hole was necessary to precision ream a pilot hole to 330 mm (13 in.) and then raise bore a 6-m-diam (20-ft-diam) shaft, planned as the primary men and materials access between the two levels. Core was not really necessary to gain an accurate geological picture of the steeply dipping formation. Rather, the core barrel was used because it tended to drill a straighter hole. Using rock bits in the steeply dipping formation would have simply aggravated the problem of deviation. The core barrel and diamond bit optimized the probability of a straighter hole. However, on the first two attempts to drill the pilot hole, the bit was out of the 300-mm (12-in.) target cylinder within the first 50 to 60 m (164 to 197 ft), and the holes were abandoned.

Jan 1, 1990

By R. E. Weeks, D. J. Millenacker

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time- frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The US Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1987

By Y. J. Wang

Along with the inexpensive availability of computing hardware, a proliferation of powerful personal computers is being realized throughout the mining industry. People from every arena within the industry are designing, developing, and/or applying mining specific software, which is increasing at a rapid rate. In this section applications (or potential applications) that are being made in the analysis and design of mine systems are discussed, including the design of compressed air networks, the simulation of hoisting operations, analysis of longwall face maintenance, and a summary of computer and software applications for analysis and design of coal operations. In "Computer Aided Design of Mine Compressed Air Networks" the authors describe software, called CompAir, and the underlying theoretical and mathematical foundations of it that can be used to make accurate, cost-effective designs of compressed air systems for mines. It includes algorithms for network analysis and the optimization of pipe diameters. The techniques embodied in the software replace traditional rule-of-thumb approximations which have been used in the past and avoid the operating problems that often result from using average, steady-state parameter values, estimated for ideal operating conditions. CompAir, coded in Turbo Pascal for personal computer use, bases calculations on compressible fluid theory, which gives more accurate results than incompressible fluid theory whenever high flow rates or long line distances are involved. The net- work and pipe diameter analysis is formulated as a nonlinear programming problem. The solution technique requires a trial and error approach that iteratively applies the unconstrained optimal pipe diameter algorithm to successive solutions of the constrained network problem until the diameters become "fixed." The authors conclude by recommending the use of a mine-wide monitoring system to improve cost control and provide a better understanding of flow regimes in compressed air networks.

Jan 1, 1989

By Y. C. Kim, W. L. Meyer, W. Cai

Although the first published optimum pit limit design algorithm by Lerchs-Grossmann dates back to 1965, the majority of the open-pit mines in the US has not as yet adopted such a rigorous optimization algorithm. Instead, the floating cone approach initially developed by Kennecott Copper in 1961 is still used today for various reasons. However, shortcomings with the floating cone algorithm, particularly for precious metal deposits with erratic mineral distributions, have provided a renewed interest in optimizing algorithms. This paper compares the performance of the floating cone algorithm with the rigorous optimization algorithm of the Lerchs-Grossman's graph theory and the newly developed maximum network flow algorithm by Hanson (1986). The maximum flow algorithm is a modified version of the logic as initially advocated by Johnson in 1968. Comparisons are made for three different deposits in terms of the total profits generated and the computation times involved. The results of the comparison show that both algorithms produced higher total profitability pits than the floating cone in all three deposits, although the increase in profits never exceeded 1 % of the base design obtained using the floating cone. Between the graph theory and maximum flow, graph theory produced consistently higher profits. The current version of maximum flow, however, cannot be modified to produce the optimum pit. Nevertheless, the authors prefer the maximum flow over the graph theory, simply because it is easy to program as well as to explain.

Jan 1, 1987