Search Documents

By G. P. Saseen, R. A. Haney

The US Mine Safety and Health Administration (MSHA) developed a model to estimate diesel particu¬late (dp) exposures in underground mines. The estimator uses in-mine measured dp concentrations or engine manufacturers' standardized emission data. Through a series of calculations, full-shift dp concentrations are estimated by applying standard engineering principles of ventilation, control technology and work cycle. This model, in the form of a computer spreadsheet, provides the mining industry with a method for estimating dp levels and determining the impact of various diesel particulate controls on occupational exposures to dp in underground mines. A detailed description of the estimator and several examples demonstrating the results are provided.

Jan 1, 2000

By M. C. Williams, T. P. Meloy

For over thirty years the Population Balance Model, PBM, has been the mainstream modeling method for comminution unit operations and comminution circuits. For commercial comminution circuits the method is based on erroneous physics and dubious numerical mathematical methods leading to non unique solutions that have little extrapolative value and faulty control strategies. In short the PBM is wrong. Given is a detailed analysis showing a number of non trivial flaws in the linear PBM. Moreover, a simpler model is presented that leads to a solution of the comminution circuit predicting the size distribution output over a variety of conditions. Because the linear PBM is firmly entrenched, an award is offered, $10,000, to any researcher that can use the linear PBM and its present numerical methods to predict the typical straight line, self similar, output of wet mills over a variety of grinding times.

Jan 1, 1992

By Jr. Wallace

This paper describes an analysis performed to determine the cool-down time of drifts in the prospective commercial nuclear waste repository in volcanic tuff at Yucca mountain, Nevada. Two emplacement methods are currently being considered at Yucca mountain. The reference configuration stores the high-level waste in short vertical boreholes, and the alternative configuration stores the waste in long horizontal bore-holes. After emplacement operations for each emplacement drift are complete, the drift will be closed off from continuous ventilation. Given time, the radioactive decay of high-level waste will increase the rock temperature around access and emplacement drifts. Air cooling may be required to re-enter these drifts. The paper discusses the analysis procedure and computer programs used to evaluate the time to cool a drift to acceptable environmental conditions 50 years after emplacement of high-level waste. Key assumptions to the analysis are presented. The results of the study show that cooling either vertical or horizontal configuration emplacement drifts is possible in a reason-able period of time.

Jan 1, 1988

By Steve Kral

"Gold rush" is usually associated the western United States - California, Nevada, and Colorado. The southeast section of the nation is known more for its rice, textiles, tobacco, indigo, and cotton. This area, though, is where it all began with gold in this country. The United States' first gold rush, in fact, is said to have started with the discovery of a 7.7-kg (17-1b) nugget in the Piedmont section of the Carolinas in 1799, some 50 years before the rush to California. The Carolina gold rush continued intermittently through 1942 when the Federal Government shut down all gold operations. Strong gold prices throughout the early part of this decade and new extractive technologies spurred a small resurgence of gold operations in South Carolina. Mind you, this is not Nevada with its flood of geologists and mining companies. Nor are there any 7.7 kg (17 lb) nuggets being discovered. But Ridgeway Mining Co., a joint venture between Kennecott Corp. and Galactic Resources, has set about mining 51 Mt (56 million st) of low-grade ore containing an estimated 43.5 t (1.4 million oz) of recoverable gold. The open pit, carbon-in-leach operation is located near the town of Ridgeway in South Carolina, about 32 km (20 miles) north of Columbia. Carolina gold North and east of Ridgeway, Piedmont Mining Co. operates the historic Haile gold mine near Kershaw, SC. And Brewer Mining Co. operates the nearby Brewer deposit. Between 1829 and 1942, South Carolina gold mines produced 10 t (318,800 oz) of gold. It all began in 1799 when Conrad Reed, son of a German immigrant farmer, found the 7.7 kg (17 lb) nugget in Little Meadow Creek, NC. His father thought the rock was worthless and used it as a doorstop, so the story goes. It took nearly three years before Conrad's father decided his doorstop was indeed gold. Gold was later discovered in the Greenville district of South Carolina. And, in 1828, Benjamin Haile discovered gold in a stream that ran through his property in Lancaster County, SC. Haile's mine became South Carolina's most famous and most productive gold mine, producing more than 7.8 t (250,000 oz). At first, miners worked the stream beds of Haile's property. Later, lode deposits were discovered on slopes alongside the creeks. They would lease 4.6 ml (50 sq ft) lots and mine as deep as 7.6 m (25 ft). During the Civil War, the Confeder-

Jan 1, 1989

By R. L. Loofbourow

In addition, dewatering is seldom complete because of aquifer irregularities and an operator's natural reluctance to start a costly study program, provision of wells, and pumping long before mining begins. In some cases, water pumped from the mine is used in treatment. This use is suggested as a way to minimize effluent effects. The true objective of water supply, however, is to provide water of satisfactory quality at the rate needed and at the least cost. Pumping to permit efficient mining isn't likely to coincide strictly with that objective during much of the mine life. The history of mining is replete with efforts, some highly ingenious, to control mine water. Methods that might be used to tackle the challenge Operators of wet mines are faced with both obvious pumping costs and some unquantified water costs. It is possible to reduce both types of costs, generally by reducing inflow to the mine area-and a surprising number of methods have been used to do this. Both the obvious and unquantified costs at a wet mine are now multiplied by: •Increasing costs of power, labor, equipment, and supplies; •Work at greater depth and, in some cases, in wetter ground; •Increasing use of hydraulic fill; and •Increasing zeal in protection of surface and groundwater quality. There are many easily overlooked ways in which mine water may add to hazards and costs (Loofbourow, 1973). As to their importance, consider these examples: •Increased maintenance of equipment, tires, roads, and ditches; •Increased difficulty in supplying proper ventilation; •Increased hazards from ice and use of electric power; • Loss of friable ore minerals and fines stuck on conveyances and in chutes; •Need to use more expensive methods and explosives; and •Decrease productivity of equipment and personnel. Expressed as cost per unit of ore produced, these unquantified costs can be high. Ideally, advanced dewatering should eliminate most of them. Advanced dewatering is a highly effective water control method, but it isn't problem free. Mines in ideal ground for advanced dewatering are most unusual. To be effective, water must be pumped at a comparatively high rate for a period longer than the life of the mine, from below mining depth. Effects on both groundwater and surface water are likely to be drastic. of increasing mine water costs are listed in the accompanying table. Ten groups of possible methods are cited. Most have been demonstrated in mining; two are known from industries other than mining.

Jan 12, 1980

By Michael Chender

Introduction Clearly, many problems confront the minerals industry today. Yet, at the same time, there is too much energy spent bemoaning the negative effects of difficult economic circumstances, low metals prices, and adverse government policies. These are factors that cannot be altered by individual mineral company reactions. In fact, as we look to the future, the only thing we can be certain of is that we will continue to be faced with uncertainty. Thus, an area that demands close scrutiny and that can significantly affect a company's performance in the future is the posture it adopts to deal with uncertainty. This paper looks at how strategies are developing to deal with this issue. It also examines some of the implications that implementing such strategies have for the role of the individual explorationist. Elements of strategy Whether mineral company strategies are based on diversifying or retrenching, on emphasizing primary production or downstream integration, there seems to be increasing agreement that in the current environment strategies must have several features. They need to be information-based - developed out of access to timely and complete data and analysis about proposed directions and competitor activity, rather than simply following a current fashion. They need to be flexible - adaptable in light of changes in the marketplace and an unpredictable industry. And they need to be cost-efficient - making the most of limited resources. Whether a company is looking for gold financing opportunities, acquiring polymetallic prospects, or doing grassroots exploration for diamonds, these three elements are increasingly essential. They not only allow the company to pursue its current goals most expeditiously, but also open it to hearing and using feedback in the most constructive way. The company can then improve or change strategy as it proceeds. And it can be best positioned to take advantage of opportunities as they arise. These elements of strategy place great emphasis on the skills of the individual. The need for critical intelligence and the reduced amount of capital available to manage are making it more obvious that exploration is a "people" business. This is in accordance with a general trend in many sectors of industrialized economies, reflecting the widely discussed shift from smokestack to information-based industries. Increasing the odds There is a direct connection between successfully implementing the approaches to strategy discussed above and encouraging and improving the quality of work of the individual explorationist. To illustrate the importance of this, some commonly quoted figures on the odds of discovery success can be used. These figures are arbitrary but illustrative. Assume that one out of 100 exploration prospects actually turns out to be a promising ore body, and that one out of 1000 becomes a mine. Based on our research, chances are the most of those

Jan 1, 1986

By Gerhardt A. Bennewitz

The mechanism shown here (Fig. 1) may not be all that it appears to be. To many of you it may look like a hopper car, a thing of mobility, in which you would ship coal, ores, limestone, or other bulk materials. It is approximately 50 feet long, 12 feet high, and can be placed on tracks which are on approximate 14 foot centers. But far too often in the past, and all too often today, this mechanism has been made to serve as an immobile storage box, with its primary role -- the transportation of products, seemingly incidental to the storage function. Our engineering training teaches us to conserve resources, despite some of the popular and misconceived philosophies being advanced these days. Those of you who work for companies with traffic departments know that they are always striving to reduce the price which is paid to move your mine products. Today, let's consider and analyze the ways in which the cost of transporting your mine products might be reduced, based on particular reference to coal. Bear in mind that in this context, cost and price are not necessarily synonymous. Until a few years ago, most coal and other bulk materials handled by railroads moved under standard tariff rules. These rules, which still exist today, provided transportation vehicles (railroad cars) for extended periods at no added price to the shipper or receiver. "Normal" free time rules would permit a car to be held for a maximum of 48 hours without charge; however, in the case of coal, there is a rule which, subject to liberal rules as to the

Jan 1, 1972

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By S. Stebbins

In 1994 Western Mine Engineering, Inc., (WME), which is now InfoMine USA, Inc., set out to build a suite of stand-alone software programs that would provide their clients the means to estimate the costs of developing and operating mineral exploitation projects. After the first program (Sherpa for Surface Mines) was completed and launched, the developer (me) left WME to form Aventurine Engineering, Inc., in order to complete the series of applications. In the years since, four programs have either been developed or upgraded and enhanced. Applications were produced that estimate the costs of underground mining, placer mining, and project site reclamation. In addition, an application specifically designed to evaluate the economics of these projects, which was based upon a program previously developed for WME by Bill Willoughby of Willoughby & Associates, was redesigned and the code updated to a MicroSoft compatible platform. All these programs follow an engineering-based approach to cost estimating. Instead of relying on rules-of-thumb and statistical averages, they calculate all of the engineering and operational parameters needed to estimate costs. The premise is that the uncertainty associated with cost estimates should lie with the data available for the resource, not the approaches used to design and estimate the associated design parameters. In other words, it is acceptable that items such as the resource grades, deposit dimensions, ore and wall rock characteristics, and mill recovery rates carry with them some uncertainty, but parameters such as loader bucket capacities, truck speeds, pump horsepowers, hoist velocities, and grinding mill diameters can be calculated (although uncertain data might be used in those calculations). No additional uncertainties should be introduced because the cost-estimating procedure relied upon statistical manipulation or anecdotal inaccuracies. To that end, the programs rely upon calculation-based approaches to selecting and sizing machinery, assigning the required workforce, and determining the extent of the consumables needed to recover mineralized material at a rate defined by the client. And while calculation-based software is not unusual, more modern approaches work toward the development, accumulation, and manipulation of data. INITIAL CONDITIONS AND PROJECT GOALS In 2016 we had five separate programs completely disconnected from one another. Each was written in VisualBasic, a language that was falling from favor. In essence, the status in 2016 was a series of stand-alone programs (Figure 1) in which results from one needed to be manually entered as input into another.

Jan 1, 2019

By V. L. Zajakowski, J. D. Gargulak

The current political climate has forced multinational cement manufacturers to consider technology that minimizes GO, emissions. Along with this environmental issue, individual manufacturing facilities are under constant pressure to increase productivity and lower costs. The use of processing or functional additions can help address these difficult demands by maximizing the extender content in blended cements. Recently, cement standards have been modified such that additions can be employed to improve quality. By using these "cement performance enhancers," the cement manufacturer can maximize extender content of cement thus optimizing plant economics, while meeting local quality standards and minimizing greenhouse gas emissions.

Jan 1, 2003

By J. Brinen, D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study copper ion adsorption, and its effect on subsequent sulfide collector adsorption, on pyrite and pyroxene minerals under flotation related conditions. Copper was found to adsorb on both of these minerals and cause enhanced sulfide collector adsorption. The distribution and depth profile of copper and collector on these mineral surfaces were obtained by using SIMS in the imaging mode. The results of this study have provided a valuable insight to understanding pyrite and gangue flotation observed frequently in operating plants.

Jan 1, 1995

By A. Jolly, A. R. Kumar, T. Novak

"Coal dust in an underground mining environment has always been a health and safety issue, especially with longwall faces. Efforts to integrate a flooded bed scrubber within a longwall shearer are underway at the University of Kentucky (UK) in order to reduce worker exposure. Small scale physical modeling, along with numerical modeling and full-scale experimentation, are engineering tools being used by the authors for simulating operating conditions underground. Recent advances in affordable 3D printers offer a means for fabricating accurate, scale models for obtaining timely insights prior to building large, expensive test setups. Comparing scale-model results with those of numerical modeling, such as computational fluid dynamics (CFD), lends guidance and confidence in a proposed design. This paper discusses the small scale physical modeling of a longwall shearer with an incorporated flooded-bed dust scrubber in its operating environment. A tracer gas was used in the model in lieu of dust to measure dust-capture efficiency. Results obtained from the physical model are presented and compared with those of CFD model. The small scale model and the CFD results demonstrate good agreement. Dust capture results show the usefulness of the approach in advance of actual design implementation. INTRODUCTION Dust generation is an undesirable, but innate, byproduct of all mining processes. It is particularly problematic in underground coal mining, where coal dust poses potential hazards from two fronts – health and safety. Coal workers’ pneumoconiosis (CWP), commonly referred to as black lung, is a chronic lung disease that results from the long-term overexposure to respirable coal dust. Although the prevalence of CWP has steadily and significantly declined over the three decades following the Federal Coal Mine Health and Safety Act of 1969, a study by the National Institute for Occupational Safety and Health (NIOSH, 2008) indicates that significant health hazards associated with respirable dust still exist within the coal mining industry. In addition to being a health hazard, coal dust can also create a potentially catastrophic safety hazard. Dust that is not captured or removed at its source is suspended and transported throughout a mine by the ventilation airstream. This float dust is subsequently deposited on all mine surfaces along its travel path. Without adequate application of rock dust to these surfaces, forces from a localized methane ignition can reintroduce settled coal dust into the airstream creating an explosive mixture. Therefore, capturing and removing coal dust at its source mitigates the probability of two major hazards that continue to plague the mining industry."

Jan 1, 2016

By G. J. Hartman

The Fort Cady in situ borate mining project involves recovery of boron from a mineral deposit located over 1400 feet below the surface. The resource recovery method is being developed using in situ mining technology employing weak acid solution injected directly into the ore body. As the acid contacts the calcium based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by use of submersible pumps. At the surface the borate values are recovered as a finely divided solid white powder after a series of chemical reactions and precipitations resulting in the production of calcium borate. The refined product is then sold under the trade name CADYCAL 100.TM All environmental permits for up to a production rate of 90,000 tons per year have been obtained. These permits required an Environmental Impact study (EIS) for federal lands and an Environmental Impact Report (EIR) for the private portion of the property. Regulatory permitting required over 5 years to obtain all the various authorizations for this project. The ore body has an average thickness of 118 feet extending over 273 acres. At a production rate of 90,000 tons per year with only a 70 percent resource recovery allowance, in place reserves are sufficient to sustain production for over one hundred years.

Jan 1, 1997

By L. Mao, R. Yoon

The thin film balance (TFB) technique was used to measure the equilibrium thicknesses of the water films formed between two oil phases. The measurements were conducted with dodecane at varying concentrations of dodecylammonium chloride, pH, and electrolyte concentration. The data obtained in the present work were used to calculate the surface forces acting between the two oil phases. The calculation was carried using the Extended-DLVO theory with the surface potentials calculated from the Gibbs adsorption isotherm. The results show that oil droplets suspended in water are hydrophobic and the hydrophobicity changes with surfactant and electrolyte concentrations.

Jan 1, 2004

By A. K. Mukhopadhyay, B. Sikdar, V. P. Arora

Introduction During the past several years, persistent concerns about an economic slowdown in India have tempered capital-expan¬sion plans. This has encouraged companies to find methods of increasing the capacity of existing production equipment. One of the more cost-effective methods of increasing produc¬tion capacity without major capital investment is to improve equipment maintenance to prevent needless machine down¬time. This can have a significant financial impact because of reduced maintenance costs and increased machine availabil¬ity. The maintenance program employs different techniques, but the analysis of the vibration behavior of machine compo¬nents to assess their condition was found to be the most accurate technique for monitoring various machine disorders. A dragline that handles overburden in open pit mines is one of the more capital-intensive pieces of production equip¬ment. It is imperative that the machine be run at its optimum capacity under the prevailing environmental conditions. Condition monitoring of the various components of the dragline through vibration analysis not only improves the machines availability but also ensures a long operation time free from sudden failure. This paper describes the application of vibration monitor¬ing and analysis techniques to assess the components of a W2000 dragline. The paper reveals that condition monitoring through vibration analysis can be as valuable in failure prevention as it is in failure analysis. Finally, the paper presents an approach to a knowledge-based expert system to the quick and correct diagnosis of mechanical faults in a dragline. Equipment A dragline is an intermittent-discharge-type excavator having a long boom at one end. Unlike other excavators, the bucket is not rigidly held by the frame structure. In favorable geomining conditions, the intensive operation of these exca¬vators is the least-expensive means of overburden removal. The basic working elements of this equipment are the hoist system, the crowd and retract system, the wing mechanism and the propel mechanism. The walking dragline is accepted as the most economical machine for stripping overburden at depths of up to 60 m (200 ft). They are electrically powered and the various motions are effected by individual drives. The Ward-Leonard system is used to provide the optimum flexibility in controlling different dc-drive motors. To mini¬mize the cost of mineral extraction, the largest such machine in India has a 24-m3 (850-cu ft) bucket with a boom length of 96 m (315 ft). Draglines are very costly, and considerable financial penal¬ties may arise from sudden stoppages due to component fail¬ures. Thus, operational reliability is of the greatest importance. Active measures are now being taken to minimize downtime by adopting condition-based maintenance techniques. Though a number of techniques come under this scheme, it has been observed that assessing the health of the dragline by measuring vibration is the best method of determining the dynamic behavior of its various rotating components to avoid any catastrophic failure. Based on criticality, the vibration-behav¬ior of the following components are studied: • motor-generator unit, • exciter unit, • hoist motor-gearbox unit, • hoist drum-gearbox unit, • drag motor-gearbox unit, • drag drum-gearbox unit and • swing motor unit The approach Increases in the vibration levels in different subsystems of the dragline were observed due to the presence of faults such as unbalance, misalignment, looseness and bad bearings. A vibration behavior study included the measurement of vibra¬tion level, trend analysis of time-domain vibration signals and vibration frequency analysis at bearing points of the components. A vibration meter, a vibration analyzer and a data collector are used. Vibration-level measurement. When the dragline was assembled and put into operation for the first time, vibration data were collected to generate baseline data for the equip¬ment (based on International Standard ISO 2372). After¬wards, the vibration levels were recorded regularly using a vibration meter. The measurements were taken at all bearing

Jan 1, 2000

By Kerry M. Masson

Perhaps the hottest item on the agendas of most state legislators this year is the state budget. The main question: Where will all the dollars come from to finance health care programs, state jobs, unemployment compensation programs, and on and on? This is especially so since people are out of work, business bankruptcies are up, sales are down, and incoming revenues from some sources have decreased or dried up. A sure bet is that state taxes will be increased in some form or another. The mining industry could face increased income taxes, property taxes, severance taxes, or even a host of new taxes (if the state does not already have them) like a gross receipts tax, investment tax, or tax on revenues made outside state borders. That's bad news for an already depressed industry, even though increased taxes may be the least of the industry's worries in the current economic climate. While reopening existing mines and developing most new mineral projects depends primarily on higher commodity prices, new taxes still could pose long term concerns for mine project development. Just how mineral tax law impacts a project is not easy to figure. It involves a complex set of calculations based on interpretations of numerous federal, state, and local tax laws that change almost annually. At best, projections of tax effects for the life of a mine are educated guesses. At the same time, projections are necessary to evaluate the economic feasibility of a mineral project. At a recent Technology Transfer Seminar, the US Bureau of Mines introduced a computer software program designed to evaluate the feasibility of a mineral project and to determine the tax effects on the project's discounted cash flow rate of return (DCFROR). The program, called MINSIM, began in 1967 as a 200-statement FORTRAN II program for evaluating a hypothetical large-scale open-pit gold mine. This single-commodity oriented program employed discrete simulation techniques and a continuous DCFROR was used to measure the effect of changes in revenues and costs. Over the past 15 years, MINSIM has developed into a program 70 to 100 times larger than the original. Basically, it will analyze costs and parameters specific to an identified deposit, then determine the DCFROR. Or by using a specified DCFROR, it will determine the primary commodity price required to attain that specified rate of return. MINSIM, which is explained in detail in this article, is available from the Division of Minerals Availability, USBM free of charge. Written in FORTRAN IV, it comes on punch cards or magnetic tape and is compatible with most major computer systems. The MINSIM Program The main objective of any freeenterprise mining venture is to make a profit. To determine profitability of a given project, alternate methods of operating and financing must be evaluated. That is the purpose of MINSIM. While there are a number of methods of evaluating the economic profitability of a mining project, MINSIM uses the Discounted Cash Flow Rate of Return (DCFROR) method as its major criterion because DCFROR considers the time value of money and gives the truest measure of profitability. One disadvantage is that the calculations are deposit oriented. In other words, MINSIM analyzes only those costs and parameters specific to the deposit. It cannot be used to evaluate the overall corporate picture. The program is designed to simultaneously handle five different commodities and a leach operation for any type of mining project. For example, analysis of a coal project would include only one commodity-coal at the mine mouth. Analysis of a copper operation might include numerous commodities-from the raw material to the refined product. Input MINSIM considers capital investment-recoverable exploration, acquisition, and development costs; depreciable capital investments such as mine plant and equipment, mill plant and equipment, and infrastructure costs; all general and commodity specific operating costs; and the cost of alternate financing methods. The program has the capacity to incorporate different types of depletion allowances, numerous commodity-dependent severance taxes, variations of property taxes, and many methods for calculating state or provincial taxes. There are even many different ways to calculate federal and national taxes. The capacity to handle tax variations is generated from an internal subroutine in the program called the "open file." The user can reconstruct, customize, or evaluate any kind of tax desired. Outputs Given this kind of capacity for numerous input parameters, MINSIM is capable of the follow¬ing major outputs:

Jan 3, 1983

By Yi Luo

Longwall coal mines are frequently located in steep mountainous areas with narrow valleys. In order to protect surrounding watersheds and residential structures, support areas are left under the valleys. However, the indirect subsidence effects to the residential structures due to the potential topography effects can be a serious problem. The present study examines a longwall mine in southern West Virginia located in an area with an average slope of about 30°, or 58%, and with an overburden depth that varies from 49 to 376 m (160 to 1,235 ft). A comprehensive investigation was carried out to assess the subsidence and topography effects, as well as other ground control issues at this site. Surface and subsurface movements and deformation were predicted and their direct effects on nearby streams and structures were assessed. The potential and indirect subsidence influences of surface topography effects were assessed. The techniques and results of this investigation are presented in this paper. It shows that the direct and indirect subsidence effects on the streams and residential structures should be insignificant. The post-mining observations agreed well with this study.

Jan 1, 2010

By J. Driscoll

After 30 years of success, Newmont Gold Company has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East Decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East underground at the rate of 700 t/d (770 stpd) for an annual production of over 100,000 ounces. Over 70 underground miners enjoy the estimated 6-year mine life at Carlin East. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By S. K. Kawatra

Although temperature is known to have a substantial effect on many processes, this parameter has been widely dismissed as insignificant for mineral comminution. For this reason, temperature effects on grinding have largely escaped notice. However, it has been observed that processing plants which are subjected to large seasonal temperature variations show a change in performance which appears to be due to changing feed temperatures. The general effect is an increase of the specific energy consumption as the temperature decreases. In autogenous mills, an increased rate of production of critical-size material has also been observed. This is due, at least in part, to changing rheological conditions in the mill, with the slurry viscosity increasing markedly at low temperatures. Mechanical changes in the rock with temperature, such as increased brittle fracture, is also responsible for a portion of the observed seasonal effect, and may account for this phenomenon being observed only in certain plants.

Jan 1, 1989

By C. DeRossett, K. F. Unrug

Sedimentary rock fractures commonly occur in the vicinity of outcrops. Mine highwalls and highway cuts provide excellent views of these near-surface joint systems. This paper explains the origin, characterization, distribution and extent of the these joint systems with reference to the lithologic composition of the rocks. The practical implications of these joint systems on the operation of a mine are described. Included are discussions of the discontinuous deformation that results from surface subsidence, the stability of mine portals and near-outcrop underground operations, and the stability of highwalls when using highwall miners and strip operations. Some design procedures are recommended to minimize the problems encountered within mining areas having intense joint systems.

Jan 1, 1996