Search Documents

By A. Spearing

According to a 2000 NIOSH report, about 100 million rock anchors are installed annually in coal mines in the USA. Most coal mines have conditions that are conducive to corrosion of the rock anchor and ancillaries (such as plates), yet the effect of this on the performance of the anchors has not been adequately researched and its effects are not understood or quantified in the USA. There is considerable research into corrosion in civil engineering applications on surface and underground but the corrosion of coal mine rock anchors is not necessarily the same because: ? In underground civil structures, water ingress is usually stopped as part of the construction process. ? Many rock bolts in mines are only partially resin grouted leaving part of the reinforcing member exposed to corrosive conditions. All cable bolts in coal mines are only partially resin grouted. ? Even when mine bolts are fully grouted, shrinkage cracks occur and the rock stresses can change due to adjacent mining that can cause the resin column around the bolt to fracture further under external shear or tensile stresses. Most coal mines therefore have ideal conditions for bolt corrosion.

Jan 1, 2010

By James A. Pappas, Francis L. Fong, Tracy K. Lundin

The impact of environmental regulations on the quality of tunnel groundwater discharges is examined in this paper. Tunnel contractors usually depend on specialty contractors or outside consultants to deal with this issue without carefully examining their activities to minimize the production of contaminants. This approach may not be adequate given increasingly more restrictive environmental requirements. This paper surveys the general practice of the tunneling industry and attempts to identify sources of contaminants which may affect the total suspended solids, oil and grease content, and pH of the discharges. Strategies for treating the discharges are included. Field data and observations from several tunneling projects are also presented.

Jan 1, 1995

By L. K. Lepley

A marine sonic sub-bottom profiling system and a hovercraft were used in an engineering geophysics survey of the tailings being deposited at the Mercur gold mine. Detailed density sections with vertical resolution of one meter were desired for computations of strength, permeability and potential self-compaction. The logistical problems of conducting a geophysical survey and in collection of geotechnical soil samples from an active tailing impoundment was solved by using the amphibious hovercraft for towing and transport on the impoundment. The "chirp" sonic system produced continuous, real-time geophysical cross-sections with vertical resolution of ten centimeters showing possible trapped gas. The hovercraft provided a platform over water, ice, slurry, and solid beach for collection of geotechnical information and physical samples.

Jan 1, 1994

By S. K. Kawatra, T. C. Eisele

A horizontal-baffle arrangement has been developed to prevent excessive axial mixing in flotation columns. These baffles have been shown in previous work to improve the grade/recovery performance of both a laboratory-scale column and a pilot-scale column (Kawatra and Eisele. 1993). In this paper, results are given for continuous on-line operation of the pilot-scale baffled column in a commercial coal- cleaning plant. These results show its ability to operate for extended periods without plugging, to produce a consistent-quality product even while the feed quality was fluctuating, and to remove much of the pyritic sulfur from the coal.

Jan 1, 1995

By Zhang You-di

A comprehensive model has been set up for surface mine long range planning. It is a system simulation model based on the oriented graph theory. Via this model, a series of mining results such as mineral and waste volume, mineral quality, mining intensity, material haulage distances, dumping area parameters and mining coat for different mining alternatives, can be derived and optimized. This model has been applied to 37 mining alternatives in several surface coal mines and proved mathematically correct and results reliable.

Jan 1, 1986

By Jiang Shuguang, Zhang Huicheng, Wang Xingshen

Based on the experience about determination of properties of the main fan in mine shaft, this paper relates at length how to reasonablly select test system, test methods and test instruments, how to appraise the reliability of determination results, and how to effectively control the adjusted air etc. The merits and demerits of the two methods of determining air with Nine- Anemometer and Pitot meter are compared.

Jan 1, 1991

By Fu Lizhu, Qiu Tingsheng

An application of water-system magnetizing technology for the mineral processing and hydrometallurgy is introduced in this paper. The water-system magnetizing technique flotation and cyanidation leaching test of vein-ore of gold-bearing and conventional technique flotation and cyanidation leaching of gold-bearing vein-ore was carried out. The best condition of water-system magnetizing was determined by orthogonal test. The results have shown that the water-system magnetizing technology may increase the efficiency of flotation and cyanidation leaching for gold. The industry-scale test results also show that it can increase flotation recovery by 1-3% and leaching extraction by 3-5% of a gold-bearing vein- ore. The interaction of magnetizing water-system with minerals was carried out and initially investigated.

Jan 1, 1995

By J. S. Lewis

Beneficiation and physical and chemical processing of non-terrestrial materials will borrow strongly from terrestrial experience but will also involve the necessity of handling literally unEarthly feedstocks, reagents and environmental conditions. The present state of scientific and engineering understanding of the processing of non-terrestrial minerals, gases and hydrocarbons is reviewed, with the production of rocket propellants, life-support fluids, structural metals and refractories as the goal.

Jan 1, 1994

By I. G. Ediz, D. W. Dixon, W. M. Fidler

In this paper a new method for the arresting of tunnel explosions is presented. In the proposed technique, the on coming explosion is detected by a pressure sensitive device by a pre-determined rise in static pressure. The sensor then triggers a mechanism which causes the explosion door to be closed in a specially constructed concrete barrier zone. The doors are of a special construction and consist of perforated steel plates that allow part of the blast wave to be transmitted but do not allow the passage of the flame. A number of design parameters have been identified, including: the likely amplitudes of the transmitted/reflected pressure waves that would govern the explosion door pressure loading; thickness of the perforated steel packages; perforation dimensions; heat transfer across the door and other factors.

Jan 1, 1995

By Ernest K. Yanful, Paul H. Simms

The lysimeter is a useful tool for evaluating the performance of mine waste covers or liners. A major problem with its application is the possibility for preferential flow into or away from the lysimeter, if the lysimeter soil is finer or coarser than the barrier soil or sub-base soil. Analysis of a field lysimeter using a two-dimensional unsaturated-saturated liquid flow model suggested that preferential flow would occur and little or no water would be collected; however, in the field, the lysimeters collected significant amounts of water. A similar discrepancy was found between the observed and predicted water balance of a simple laboratory test simulating the lysimeter design. Vapour flow and partial flow, two phenomena not generally simulated in conventional flow models, are possible explanations for the difference between field and laboratory observations.

Jan 1, 2000

By M. Canty

This paper presents results from pilot-scale and field testing of an innovative technology that uses sulfate-reducing bacteria (SRB) to treat and control acid mine drainage (AMD). Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides. The bicarbonate produced serves to help neutralize the drainage. Pilot-scale metal-removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium and 96% for copper. However, the iron and arsenic removals were not as effective as the aforementioned metals. This was largely attributed to high levels of iron and arsenic that contaminating the organic substrate. There was evidence that both adsorption and sulfate reduction were occurring within the reactors. The SRB field demonstration involved using the flooded subsurface mine workings of the Lilly/Orphan Boy Mine near Elliston, MT, as an "in situ biological reactor." In the mine, high removal efficiencies were observed for aluminum, cadmium, copper and zinc (70% to near 100%) during the four years of monitoring. However, for reasons similar to the pilot scale testing, low removal efficiencies were observed for arsenic and iron. Sulfate reduction was evident by measured decreases in sulfate and the detection of soluble sulfide within the mine water.

Jan 1, 2000

By B. Bringhurst, J. J. McClelland

A filter consisting of a synthetic fibrous material has been determined to be a viable alternative to the wire mesh panels currently used in irrigated filter dust collection systems. An extensive laboratory investigation of the material showed that it removed a higher percentage of both respirable coal and quartz dust from the air entering a collector than did the flat and pleated wire mesh panel designs. This improvement in dust collection efficiency reduced the amount of coal and quartz dust discharged from the collector exhaust by approximately 44%. Since continued exposure to excessive levels (>5%) of respirable quartz dust presents a severe health hazard, this alternative filter medium could be of use to those mines required to comply with more stringent dust standards due to quartz.

Jan 1, 1992

By Fabiola Espinoza Carmona, Elena Chiriotti, Edoardo Misano

"INTRODUCTION Ganntas Tunnel is part of the modernization project of the railway between Alger and Oran, in Algeria. In order to double and rectify the existing line between El Affroun and Khémis Miliana, the alignment foresees the excavation of a 7 km-long twin tunnel. The excavation works started in June 2011 with the contractor CCECC, under the supervision of SYSTRA. Excavation is driven in conventional method by hydraulic hammer simultaneously on 8 different faces since excavation was started also from a junction window towards the middle of the tunnel. The minimum longitudinal distance to be respected between two contiguous tunnel faces has been set to 30 m. The tunnel cross-section is a 70 m² oval shaped profile, temporary support consists of shotcrete, bolts and steel ribs. A 30 to 50 cm thick cast in situ concrete final lining has been provided as well. When the tunnel reached a fault zone in soft clayey marls extreme squeezing occurred, works were stopped and re-profiling operations were carried out along more than 100 m. To date, works proceed at slow rate since high convergences are still monitored and completion of works is not expected before December 2016.GEOLOGY The project is located within the Tellian Atlas mountain area, including in particular the Djebel Ganntas massif in between Mitidja and Chleff plains. Djebel Ganntas is characterized by an extensive massif aligned in East-West direction with smooth slopes made of soft clays that emerge in multiple cliffs and ravines. On the top of it, along the edge, a more recent sandstone formation is found. The existing data on the geology did not allow to establish an accurate geological model at tender stage. In-situ investigations allowed at design stage to identify a Quaternary alluvial cover of clays and gravel, followed by a Miocene stratum divided in a sandy top layer and a lower clayey layer. From a structural point of view, geological maps suggest a north direction dip of layers, but the in situ surveys showed that layers were highly folded. The lack of information at tender stage on the structure of the geological series should have triggered an extensive investigation campaign at detailed design stage which did not take place causing serious consequences on costs and time at construction stage."

Jan 1, 2016

By Juan L. Yarmuch, Hyam Rubinstein

Open-pit mine planning is a key process in the definition of mineral reserves and their efficient removal. Ore in open-pit mines is extracted bymining sequential pits called pushbacks. Pushbacks need to satisfy complex geometrical constraints to ensure the efficient usage of equipment. To date, no algorithms that both account for those constraints and maximizeNPV, are commercially available. Therefore, pushback design is done by engineers relying on their expertise to incorporate practical features intothe output of commercial tools. In this article, we present a new algorithm that produces close to optimal practical pushbacks and we illustrate its performance in real mines.

Jun 25, 2023

By C. R. Zegarra

Extraction of manganese, gold, and silver from a low-grade manganiferous-silver ore was investigated by thiourea leaching followed by standard cyanidation. The levels of reagent concentrations in this investigation were 0.0 -1.0 M thiourea and 0.0 -1.0 M sulfuric acid. Temperature and agitation speed were maintained at Z5 °c and 300 rpm, respectively. The dissolution of gold, and silver was shown to be dependent mainly on sulfuric acid and thiourea concentrations. In general, 50.0 % Ag, 98.0 % Au, and 75 % Mn were recovered from a Mn-Ag ore by thiourea leaching. Overall silver extraction of 98.0 % was obtained by cyanidation after thiourea leaching. Thiourea leaching of sodium bisulfite leach residues was also studied, and the total extraction of gold and silver were 97 % and 40 %, respectively. Finally, a two-stage thiourea leach was also investigated.

Jan 1, 1988

By G. T. Adel

The growing interest in column flotation has created a need for a fundamental scale-up procedure which is capable of meeting the necessary design and control criteria for industrial columns. Unfortunately, most of the avail able scale-up procedures deal with column diameter only and not overall column volume. Current work focuses on the effect of bubble size distribution and air hold-up on the scale- up of column volume. A series of pressure transducers has been used to measure air hold-up along the length of a bench-scale column. These measurements have been used to validate a mathematical model of the air phase. In addition to scale-up, the model appears to have the potential for use in control of air hold-up and bubble size.

Jan 1, 1990

By S. K. Mukherjee, M. M. Singh, N. I. Jayaramn

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years, there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper recommends guidelines for water spray systems to control dust in underground mining operations. These guidelines suggest type, number, location, and orientation of nozzles; desirable operating water pressure; and associated filtration system.

Jan 1, 1987

By Alex Harrison, Steve Kasper

Various countries around the world have testing and manufacturing standards in place for steel cord belting. These standards are very comprehensive in what they allow the end user to specify, however, their practical significance in terms of belt life is more difficult to quantify. Such testing standards will be briefly reviewed in this paper in relation to the implication for end user expectancy. Since there is no US standard of manufacture, the end user is left with writing their own specifications. In addition, such standards do not address the effect on belt life of manufacturing faults, such as cord plane buckles, or lateral cord movement. Some new technology used to test steel cord belting will be described as an aid to both manufacturer and end user. Specific end user related issues addressed on this paper are: Tracking and belt quality Cord plane irregularities and performance Cord size and belt life Cord fatigue and testing

Jan 1, 1993

By Abdullah Arik

The resource classification methodologies have always been a topic of research and debate. There are both traditional and Geostatistical methods used in practice. Because of the uniqueness of each ore deposit, it seems almost impossible to have a single industry-accepted norm for resource classification. Therefore, some practitioners have adapted the methodologies to suit the deposits they are working on, but many simply use the methods they are comfortable with. Another reason for the existence of varying classification methodologies is the lack of an easy and established way to measure the confidence in the estimates. Therefore, their classification becomes a subject of debate. In this paper, a new approach is offered to classify the resources using a "Resource Classification Index." The approach using this index takes into account the local variation, the spatial data configuration around the block being estimated, as well as the traditional distance measures. A case study for a gold deposit is presented to demonstrate how this new index can be used to classify the resources. The results from this approach are compared to those from two popular classification methodologies.

Jan 1, 2002

By A. A. Odunaike, E. G. Okafor, M. H. Mokwe

Microscopic Studies were performed on ore samples from the Muro banded iron ore deposit in Nigeria and the Marampa iron ore deposit in Sierra Leone. Ore characteristics that affect processing of both ores were compared with a view toward assisting mineral processing engineers in choosing the most suitable methods for upgrading the ore. The Nigerian ore contains 30% to 37% (by weight) Fe and the Sierra Leonean ore contains 34% to 51% (by weight) Fe. Hematite is the main iron mineral in both ores. The Sierra Leonean ore is relatively coarse grained (typically around 250 µm) and can be upgraded by conventional gravitational methods. In contrast, the Nigerian iron ore is fine grained and must be ground to -74 µm to liberate the hematite for recovery by flotation. Both ores contain high percentages of phosphorus and sulfur, which are above the required specifications for direct reduction and blast-furnace practice. These deleterious elements can be rejected by grinding and flotation.

Jan 1, 1999