Search Documents

By E. H. Ahrens

This paper deals with the responsibilities of an operating geologists and the relationship of operations to exploration. It should be of interest to those soon to enter the profession, those new to pining geology and as a review to more experienced geologists. Subjects discussed include detailed geologic mapping, sampling, core logging, assaying, selection of proper map scale, posting geological and assay data, section preparation, identification of ore controls, delineation of development drill targets and geologic hazards, models and the very important topic of salesmanship. Methods and ideas, proven valid in vein, pyrometasomatic replacement and porphyry copper deposits are presented. Hopefully, these will smooth the path for new members of our profession.

Jan 1, 1992

By Y. K. Yen, J. D. Miller, C. L. Lin

Particle size segregation is a common phenomenon in many particulate processes and has many undesirable effects. The size segregation which occurs on a belt conveyor causes a serious problem for on-line particle size measurement using image-based techniques. Whether particle size distributions measured from the top layer of the belt are representative of the total particle population is largely dependent on the degree of size segregation. Therefore, it is important to understand the nature of such size segregation in order to make appropriate corrections for on-line particle size analysis. Monte Carlo simulation has been used to provide segregation information on particles with simple geometry and the results can help to determine important factors in experiments with irregularly shaped particles. It is expected that the relationship between the particle size distribution of the top layer and that of the entire particle population on a belt conveyor can be formulated as a model based function.

Jan 1, 1997

By T. T. Chen, J. L. Jambor, J. E. Dutrizac

A reconnaissance study of the neutralization potential of 30 diverse minerals, 28 of which are silicates and aluminosilicates, has shown that most of these minerals contribute minimally to the neutralization potential (NP) in standard static tests. Feldspars in particular give low NP values and would not be expected to attenuate the acidity to any significant extent in acid rock drainage settings. The BET-determined surface areas of the minerals vary considerably, and the large surface areas of some of the pulverized samples have clearly affected the NP values even though the standard static-test protocol was used for the preparation of the samples. The low NP values of most silicates and aluminosilicates are in general agreement with the laboratory-determined slow dissolution rates for these minerals. The results suggest that, in the prediction of whether rocks will be acid-producing, the most realistic measure is that of the carbonate content. In mine wastes from metalliferous ore deposits, the contribution to the NP by the non-carbonate gangue assemblage is unlikely to be more than a token amount until well after the establishment of an acid rock drainage situation.

Jan 1, 2000

By J. E. Rourke, O&apos

This paper describes the use of index testing to obtain rock properties that are useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include: point load; Schmidt hammer hardness; abrasion hardness; and total hardness. The first two index properties correlate to uniaxial compressive strength (UCS) and Young's modulus. Discussions are given on empirical, normalized relationships of UCS to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The hardness property indices correlate to construction performance parameters and some relevant experience is cited. Examples of data are presented from an index testing program carried out primarily on siltstone, sandstone and limestone rock core samples retrieved from depths up to 1005 m (3300 ft) in a borehole drilled in the Paradox Basin of eastern Utah. The borehole coring was done for a nuclear waste repository site investigation.

Jan 1, 1990

By Jianping Sheng, Francis Otuonye

The potential for methane and coal dust explosions in underground coal mining operations has increased in recent years with the introduction of fast coal-cutting machines. Dust explosions usually follow accidental ignition of a methane pocket. The dynamics of the explosion may be strong enough to pick up and disperse coal dust deposited on mine surfaces and ignite the mixture. A self-sustaining dust explosion can then develop and propagate at large distances. Ignition of dusts can result in a fire, and this may also lead to a dust explosion if the burning dust becomes airborne. Entrainment of dust and the resulting dust concentration in the gas stream are some factors which determine the features of the subsequent explosion and flame propagation. A model of coal dust transport in the gas stream due to the initial explosion is presented. In this model, equations for the conservation of mass, momentum and energy are coupled with the convective-diffusive model of dust transport. The system of equations is solved numerically to obtain dust concentration, convective velocity and gas pressure profiles.

Jan 1, 1989

By Betty L. Gibbs

What does the information age mean to mining companies? The perception of greatly increased access to information is based on modern communications through ‘smart’ fax machines and computer networks. Computer media allow us to `talk' to the President or to a sister in Australia. If we need data to help put together a mining permit, we can find that data somewhere on computer media. The vast amount of easily accessible information quickly overwhelms us. To avoid `information burnout,' we must learn to target searches and be able to discriminate between dross and information that is useful to our goals. If you watch commercial TV, you have learned to screen out most product commercials. A similar screening process must be applied to computerized information sources. You may need to sort through a lot of irrelevant information before finding the pearls you are looking for. ‘Smart’ fax machines can send information with no direct human intervention. MINES FaxBac, for example, from the US Bureau of Mines instructs you to enter four-digit numbers to have particular reports sent directly to your fax machine. Software vendors use a similar system to supply information about their products. You select an item by number, and the related brochure is faxed to your machine. To compete, the industry must maintain access to as many information sources as possible. The availability of computers and software for almost every conceivable application allows us to accomplish work faster than we ever thought possible, even as recently as 10 years ago. Most mining companies have become aware that doing geology, reserves, mine planning and other technical tasks completely by hand is much too slow. The world moves faster, drilling happens faster, mining happens faster, all related activities happen faster. We no longer have the manpower or time to keep all maps. calculations and records up to date.

Jan 1, 1994

By James E. Gingrich

The new Track Etch* technique for uranium exploration has been utilized in several survey programs conducted during the last few years. The results from these programs have been very encouraging, and new uranium ore bodies have been discovered by using this new technique. The Track Etch method is being used in several exploration programs in various locations around the world. The Track Etch exploration technique utilizes small pieces of special radiation-sensitive plastic film to detect the presence of radon gas which is released by uranium ore bodies. Because of the selectivity and sensitivity of the technique, ore bodies not normally detected with other surface or airborne monitoring methods are found. Since no large equipment or special training of personnel is needed, the Track Etch technique is easily used in field operations. The basis for the Track Etch method, its application in field exploration programs, and the results obtained to date in locating uranium ore bodies is discussed.

Jan 1, 1974

By Rolf Christiansson, Daniel Johansson, Urban Åkeson, Henrik Ittner, Mats Olsson

"This paper presents two recent studies on the extent of blast damage after excavation in crystalline rock. The Swedish Transport Administration and the Swedish Nuclear Fuel and Waste Management Company (SKB) are both under regulations to limit excavation damage during construction of tunnels. SKB is also required to limit the Excavation Damage Zone (EDZ), as this could be a potential flow path for radionuclides in the planned repository for spent nuclear fuel. Presented in this paper are investigations of blast damage from three tunnel sites, a road tunnel, an experimental tunnel in Äspö Hard Rock Laboratory and an underground subway depot. As expected the fractures resulting from the bottom charge are both longer and more frequent then those mapped in the column charge. The results show that the requirement to limit blast damage according to Swedish regulations was fulfilled for the column charge at the three studied sites.1 INTRODUCTION The Swedish Transport Administration (TRV) and The Swedish Nuclear Fuel and Waste Management Company (SKB) have both recently completed studies related the extent of blast damage from modern explosives after excavation. SKB studies focused on blast damage from pumpable emulsion explosives for underground construction (Ittner and Bouvin 2015) and hydraulic connectivity in the EDZ (Ericsson et al. 2015). TRV had a broader focus with different types of explosives including blasting for both road cuts and tunnelling with pumpable emulsion explosives. Investigations by means of geophysics were also conducted (Olsson et al. 2015). High demands on perimeter control and excavation damage is usually required for underground constructions with a long operation time, such as public tunnels for transport or underground repositories for nuclear waste. This paper presents the findings of recent Swedish studies and aims to discuss the topic in a broader context."

Jan 1, 2016

By G. Heiken

On the Earth's Moon, obvious hazards to humans and machines are created by extreme temperature fluctuations, low gravity, and the virtual absence of any atmosphere. The most important other environmental factor is ionizing radiation. Less obvious environmental hazards that must be considered before establishing a manned presence on the lunar surface are the hazards from micrometeoroid bombardment, the nuisance of electro-statically-charged lunar dust, and an alien visual environment without familiar clues. Before man can establish lunar bases and lunar mining operations, and continue the exploration of that planet, we must develop a means of mitigating these hazards.

Jan 1, 1991

By Manuel Bernales, Aldo Leon, Alexandra Carlier, Bern Klein, Andre Xavier

Mining companies and governments at both the local and national levels recognize that Participatory Environmental Monitoring and Surveillance Committees (PEMSC) are necessary mechanisms for meaningful engagement at the community level. In many cases, PEMSCs are established as volunteer initiatives by mining companies or by the mining communities themselves. In Peru however, they can also be recommended by the government as way to address social conflict. Most PEMSCs are launched while a mine is in operation and have the objective of monitoring both water quality and quantity. Many established committees are currently evolving and adopting a more comprehensive approach, as well as expanding their initial scope from a river or micro-basin focus and watchdog agenda, to a broader regional integrated resources management view. This paper examines the origins of Participatory Environmental Monitoring and Surveillance Committees in Peru. It also discusses the typology of these committees, and the scope of their work. Furthermore, it looks at the challenges faced by these committees, as well as existing opportunities for mining companies, governments, and civil society. Finally, this study presents a governance model that could contribute to the long-term existence of these committees. This discussion is further informed by the results of a national workshop that took place in October 2016 in Peru, in which over 200 representatives from 22 monitoring committees, government and mining companies participated.

Jan 1, 2017

By A. R. Przybylek

A fluid bed dryer has been designed for a nonconventional application to upgrade the value of fine anthracite culm and silt recovered from culm banks and anthracite tailings pond beds. This material can be seen as large spoil piles scattered throughout the anthracite coal regions of Eastern Pennsylvania. Engineering of the system commenced in December of 1986 and at this writing start-up is scheduled for late October or early November of 1987. This paper will focus on generalities concerned With system design and operation, and qualify the differences from conventional fluid bed coal drying systems.

Jan 1, 1988

By Janine L. Beazley, James H. Kyle

The effects of pH, pH modifier (lime or caustic soda) and cyanide on the pulp rheology of a number of ore types ranging from highly siliceous to highly kaolinitic has been investigated. All experiments were performed in fresh water at solids concentrations of 25 and 45% solids and in the pH range 6 to 11. The kaolinitic ores exhibited greater changes in rheology with pH and calcium ion concentration than did the siliceous ores.

Jan 1, 1989

By Ralph A. MacMillan

Electronic systems introduced for haulage equipment in recent years probably exceed what mine management is prepared to use. Haulpak trucks alone are equipped with General Electric's Statex III drive system controls, Detroit Diesel's DDEC, Cummins' Centry engine management system and the Haulpak Management System (HMS). The future holds promising developments of even more sophisticated electronics that will lead to unmanned truck operation and control. Trolley-assist will finally come into its own due to the importance of environmental issues, as well as the high potential for increased productivity with dramatically lowerfuel consumption. All of these high technology systems do not mean much unless they add value to mining operations. Some of the benefits that can be expected from these systems are reviewed. In the near future, haul truck control and monitoring systems will be fully linked by telemetry to a mine's dispatch system, as well as to its maintenance management information system. The manufacturer and distributor can also be kept in the communications loop, so that they can better serve customer needs. Portable computers will allow technicians to talk to machine systems to quickly locate a problem, look up service information, check what parts are required and electronically order them.

Jan 1, 1994

By L. Arbore

Introduction Mine operators are interested in energy conversation in two ways. With our finite sources of energy, we are concerned for future generations. In addition, as mine operators, we want to minimize energy costs. Moving material represents a substantial amount of the energy used in mining operations. Wheeled vehicles are used extensively to move materials. And they derive all their energy from fuel. Energy is also required to overcome the vehicle's inertia, and internal and external frictional forces. Included in the vehicle's frictional forces is its suspension. Tires are an important part of this suspension. What influence do tires have on the overall fuel consumption of the vehicle? Does tire construction affect this influence? As far back as 1896, it was apparent that tires were a factor in fuel consumption. A test was devised in France using a coal-fueled steam-driven auto. The test measured whether there was any fuel savings with the new pneumatic tires rather than of the then commonly used solid tires. The result was a 28% savings in water and a 29% savings in coal on pneumatic tires. Today, the pneumatic tire is accepted, but there are differences in present constructions. Tire Construction: Bias vs Radial There are basically two types of tire construction, bias and radial. Bias tires have been around for about 60 years. Radial tires are more recent. They were developed to improve a tire's ability to withstand higher speeds and loads, as well as to improve tire life and vehicle handling. Another advantage of the radial tire is its lower rolling resistance. This characteristic results in lower fuel use by a vehicle. This has been demonstrated with passenger cars and over-the-road trucks. It is now being demonstrated with earthmoving equipment. A basic description of both types of tire construction should now be reviewed: The casing of a bias-ply tire is made up of crisscrossed textile plies or layers. The cords of these plies run on a bias, from bead to bead. The cords of each ply run on an angle relative to the cords of the adjacent plies. As the tire rolls and deflects, the angle between the cords changes, like the blades on scissors (Fig. 1). The cords of one ply pull one way, and the adjacent ply pulls another, straining each other. This movement generates heat. Since the same layers of cords wrap around under the tread, they

Jan 9, 1984

By Michel David

Once a mineralized body has been delineated, drilled and estimated from surface samples, it often happens that before the final go-no-go decision is taken, an underground sampling program is decided, very often via a ramp which hopefully will be later used to extract the ore. The cost of such a program can be close to a million dollars. On other occasions, when a property changes hands and is reexamined maybe 20 years after the original drilling program, a "check sampling" program is carefully, designed to make "sure" that the old assays are "correct". One may fear poor sampling practice in old days, or deliberate highgrading by promoters. Again one may be talking of resampling cost which may be in the six-figures range. Other similar situations include the drilling of a few large diameter holes to ascertain the validity of a majority of small diameter drill holes, or auger drilling, or back-rimming. In uranium checking radiometric information is also a problem related to the above ones.

Jan 1, 1979

By Jack Parker

Pillar design ought to be a matter of matching pillar strength against pillar loading conditions to come up with dimensions that will cause the pillar to behave as required - to stand forever, or for a limited time, or to fail in a controlled manner. But something has gone wrong in recent years, seriously wrong. Pillar design practices have departed from reality. The laboratory and computer have taken the place of the mind. If the mind is put to work and such pillar design practices are examined critically, it becomes obvious that they deal with conditions that do not exist in a real mine. Time, effort and money are wasted, and the end results are incorrect and misleading. These questionable pillar design practices have been passed on from generation to generation over the past 30 or 40 years. The hope here is that we can return to reality as soon as the questionable practices are generally recognized. We could then go back into the mines and define how pillars really work, and mining safety, efficiencies and costs should improve. Let us take a close look at current textbook design practices and compare them to real-life conditions. Common sense might then prevail. (At this time, we will consider only mine pillar design, but similar scrutiny should be applied to design criteria for width of openings, floor conditions and roof support systems.)

Jan 1, 1993

By Raj K. Singhal

This paper is a report on a task force study dealing with many facets of computerization. The primary mandate of the task force was to examine the software and hardware currently available for application relating to reserve estimation, mine planning, economic evaluation, equipment selection, production scheduling and composite mine simulation and to evaluate how adequately the software fulfills the user needs in surface mining of oil sands and coal. To meet its objectives the task force consulted extensively with the users, developers and suppliers of hardware and software. The paper outlines the approach taken by the task force to fulfill its mandate, summarizes its findings and presents some pointers which might be useful to others considering this type of evaluation.

Jan 1, 1986

By K. N. Han, M. C. Fuerstenau

Challenges in five major areas of hydrometallurgy are presented and discussed. These are: leaching low-grade oxide and sulfide ores; oxidative leaching of sulfide concentrates; processing refractory ores; bacterial leaching and processing: and secondary metal recovery.

Jan 1, 1989

By Toyohisa Fujita, Mitsuo Mamiya, W. Tai Yen, Hiroki Kogita

Green algae taken from an acidic mine drainage and blue-green algae taken from an alkaline hot spring stream were collected and tested for their ability to recover or remove dilute metal ions. Experimental results demonstrated that unwashed blue-green algae and washed green algae effectively adsorbed base metals ions and eluted them at pH 1. It was also found that washed and dried algae adsorbed precious metal ions more effectively than unwashed algae. For example, the washed and dried blue-green algae was capable of adsorbing 0.31 kg of gold per kg of algae. The gold from tetrachloroaurate solution which was adsorbed on washed blue- green algae was found to change to a metallic state following initial metal binding. In the case of a dilute gold complex solution leached with thiourea, only a small amount of gold could be captured by algae. Further experiments were conducted on components of the algae, such as alginic acid, agar, cellulose and chitin and mixtures of these components, in order to determine their contribution to metal adsorption characteristics. However, a mixture of these two components demonstrated both good adsorption and desorption characteristics indicating an interaction between the individual components.

Jan 1, 1995

By G. Reed Marchant

In 1967 the US Congress passed the "Clean Air Act." This act was amended in 1970. As a result it soon became obvious that American industries were going to have to make significant changes in their methods of operation to be able to comply with quickly developing federal regulations. One of the first regulations developed was on sulfur dioxide. For this reason, the nonferrous smelting industry was immediately affected by these new regulations. This is true because the smelting process produces sulfur dioxide as a natural product of combustion when the sulfur-bearing ore is oxidized to purify the metal. The federal government's approach for setting standards included public hearings at which government, industry, and private citizens were allowed to make comments. For this reason, it was apparent to Kennecott's Metal Mining Div. that it was desirable to make a maximum effort in working with the agency to see that correct input was provided at the hearings to assist the government in setting fair and realistic standards. It was also obvious that more complete monitoring would be required. It soon became apparent that the efforts required input from many levels of the corporation from the chief executive to the plant operators. In order to accomplish both the administrative and the technical needs, an organization was needed that could respond quickly to these needs, obtain information from diverse sources, and bring it to focus in an organized approach to the problem.

Jan 1, 1979