Search Documents

By Jack Bradbury

The open stope room and pillar method of mining is used throughout Ozark Lead Company's underground mine located at Sweetwater, Missouri. This method of mining produces an approximate overall ore extraction of 80%. Pillar recovery, on a limited and experimental basis, was started in January of 1979 to determine the maximum size underground opening that could be mined safely. Monitoring the roof and surrounding pillars for potential failure during this pillar recovery process was accomplished by utilizing a simple rod extensometer to measure roof sag. Boreholes 7.5cm in diameter were drilled 3.5m into the roof to spot any separations or cracks that might have propagated between the bedded layers of rock. Underground openings 85m in length by 46m in width have been mined successfully without roof or surrounding pillar failure. Continued measurements to establish long term results will be necessary.

Jan 1, 1981

By P. Venkatasubramanian

The selection of a mining method for a mineral deposit is a complex decision problem. Human judgment, based on experience with mineral deposits and geologic conditions, remains the single most important input of the decision-making technique. If the use of artificial intelligence, in particular the developments in expert systems, is taken to its logical conclusion, the experience of the domain experts could be incorporated into a decision-support expert system. A knowledge-based decision support system for mining method selection for ore deposits has been designed whereby the domain knowledge is represented as production rules and organized in a semantic tree representation. This model is written in the PROLOG language. While the verification difficulties of expert systems models are recognized, an example of the model's decision on the mining method for a given ore body is presented and shown to be consistent with the decision made by human experts. In addition, plans, for further verification of the model are delineated.

Jan 1, 1992

By D. W. Rierson

Svedala has a ported kiln process, designed specifically for the direct reduction of pelletized or natural lump iron ores. The process is called ACCAR. This ported kiln technology has been coupled with Svedala's GRATE-KILN System, for iron ore pelletizing, into the GRATE-CAR System for the reduction of fine grained ore concentrates through the steps of agglomeration, induration and reduction in a single production line. Additional applications of the GRATE-CAR System include: the recovery, agglomeration and reduction of steelmill waste oxide fines and the use of minus 6mm size natural lump ores to produce a highly metallized pellet agglomerate. Svedala conducts tests to confirm certain operating parameters through process simulations of the GRATE-CAR process. These tests are conducted at Svedala's Process Research and Test Center, Oak Creek, Wisconsin. Svedala also assesses issues of process variables, heat transfer, equipment sizing, retention time and endothermic demand associated with iron ore reduction using natural gas or coal as the reductant. The purpose of this paper is to present the GRATE-CAR processing concepts, the commercial production line and the testing procedures associated with investigating potential raw materials.

Jan 1, 1997

By M. J. Zdunczyk

Located approximately 50 miles northeast of Knoxville, Tennessee, Short Mountain Silica mines the Clinch Formation, an orthoquarzite, for silica sand. In 1980, a Knoxville resident and area contractor visualized mining Short Mountain for silica sand. Because APG Industries, the main market for the glass sand product, was only 48 kilometers from the site, many silica sand companies became interested in the property. In 1986, J.D. Nicewonder began to develop the site, and in May of 1988, APG Industries received the first sand shipment.

Jan 1, 1992

By Allan E. Koski

Michigan is the second largest iron ore producing state in the United States. The Empire Mine, celebrating its 30th anniversary in 1994, is the largest iron ore mine in the state. The Empire Iron Mining Partnership is an iron ore mining, concentrating and pelletizing facility managed by The Cleveland-Cliffs Iron Co., a subsidiary of Cleveland-Cliffs Inc. The Empire Mine is located near Palmer, MI on the Marquette Iron Range in Michigan's Upper Peninsula. The partnership includes Inland Steel Co., LTV Steel Co., Wheeling-Pittsburgh Steel Corp. and Cleveland-Cliffs. Mine construction began in 1960. The first pellets were produced in late 1963. Successive expansions in 1967, 1974 and 1979 resulted in Empire reaching a present annual capacity of 8.1 Mt (8 million long tons) of pellets. In late 1993, a milestone was reached with the production of Empire's 152-Mt (150-millionth long ton) of iron ore pellets.

Jan 1, 1994

Compared to alternative ways of dealing with coal fines, oil agglomeration has always been a commercial bridesmaid and never yet a bride. Yet interest is high in the process, as shown by a number of pilot plants in operation that are funded by industry as well as government. In the past in the US, alternative ways to handle coal finer than 100 to 200 mesh included flotation, or no treatment except dewatering, or discarding the fines as waste. There are now a number of factors that tilt the economics more toward fine coal recovery. Today, the cost of mining a ton of underground coal runs from $22-30, and discarding even 10% as unrecovered fine coal is a real economic loss. A number of attempts (notably by EPRI) have been made to quantify the effect of coal cleaning on utility boiler operations. Transportation and ash handling costs, frequency of unscheduled outages, fouling and slagging problems, and boiler tube erosion are all lowered by cleaning coal. The advantage of coal cleaning on these parameters has been shown, but the dollar amount varies with many assumptions and is difficult to pin down. The message to a utility, however, has not been lost and the trend toward cleaner steam coal is accelerating. This may lead to fewer installations that only wash the coarse coal, and add back the unwashed fine coal until a maximum contractual ash limit is reached. And, as the proportion of coal fines continues to increase by continuous and longwall mining, it may become impossible to clean the coal sufficiently without cleaning the fines. Flotation and oil agglomeration are the only processes that presently deal directly with cleaning the very finest coal fractions. Flotation has proven its effectiveness in cleaning blackwater and in separating fine coal from mineral matter. It has the achievable potential for far greater pyrite rejection than is now obtained in commercial preparation plants. While flotation will continue to be the predominant method for fine coal cleaning, there are conditions and opportunities where oil agglomeration can be a

Jan 8, 1980

By John T. Bartlett

With more stringent environmental and economic constraints being placed on mining operations, it has become necessary to optimize each process to minimize energy and raw material consumption and reduce waste discharge. In most cases, detailed process analysis is required to detect inefficiencies and provide alternative solutions for process improvement. HETSIM, a microcomputer process modeling and simulation system, is routinely used to analyze communition, hydrometallurgical, pyrometallurgical, and coal preparation processes. The process modeling techniques used in METSIM, including process control simulation, will be presented and illustrated using actual plant processes.

Jan 1, 1987

By E. E. Jones

The lignites of Arkansas, Louisiana and Texas are typically described as muitiseam deposits which contain quantities of day and sand in thin lenses or in admixture with the fuel itself. These materials are often included in the run-of-mine fuel and can have very adverse effects in the end use. Since May of 1982 the Dow Chemical Co. has operated a pilot plant for the beneficiation of lignites. This facility has successfully removed sand, clays and petrified wood from the lignite producing a fuel comparable to or better than the selectively harvested run-of-mine materials. The design, operation and results from this plant were presented by J. H. Everitt at the 1984 Coal Technology Conference.

Jan 1, 1986

By Edgar T. Gregory

A quiet revolution has taken place in the conveyor belt industry, Man-made materials, improved production facilities, better splicing techniques and emphasis on repair and maintenance have all contributed substantially to lowering material handling costs for the mining industry, It wasn't too many years ago that the rubber industry had only cotton for a belt carcass and tree grown rubber for the protective cover. Then came the development of monofilament rayon. This material had desirable elongation and elastic properties and was the first synthetic fiber to be used in place of cotton. But wet strength and other limitations restricted its use, and the conveyor belt industry turned to nylon. Initially, nylon was considered suitable only for the cross threads or filler threads of a belt carcass. Then technical advancements in heat setting and fabric weave created a major change in belt construction. As a result of these advances the industry was able to take advantage of the full tension strength of nylon cord. Another breakthrough in the use of synthetics was the tremendous increase in adhesion resulting from a chemical bond, rather than the limited physical bond available with cotton. But the advantages of nylon had a more Car-reaching effect, We were able to design a two-ply nylon belt that did the work of a four- or five-ply cotton or rayon belt. A six-ply nylon belt now replaces a twelve-ply cotton elevator belt. Arid nylon resists moisture, acid and mildew, It also has excellent resistance to impact and can be produced with controlled elongation and elastic properties that work to great advantage in reduced-ply belt constructions.

Jan 1, 1971

By Robert S. Saunders

Cast iron tubbing for two centuries was the only practical watertight shaft lining for deep waterbearing formations. However, since World War II composite welded steel and concrete lining has gained favor and today is often preferred. While tubbing may not be applicable in all cases, a good argument can still be made for this time-honored method. Watertight linings are complex structures designed to withstand both hydrostatic fluid pressure, non-uniform loading created by ground forces, and vertical bending caused by subsidence. Resulting stresses in the lining can be high. To date linings have been designed that withstand hydrostatic pressures as high as 1,500 psi. Watertight linings must be robust, constructed of the highest quality materials, and manufactured and installed with precision. Therefore, such linings are expensive. Today's ductile cast iron tubbing is greatly superior to gray iron formerly used for tubbing, and is stronger, and more resistant to corrosion than welded steel lining. Tubbing, unlike steel linings, can be installed in wet conditions and used to control water inflow and stabilize unconsolidated ground as the shaft is deepened. Steel lining requires absolutely dry conditions for welding, which often necessitates expensive ground freezing and a primary lining.

Jan 1, 1985

By Mark C. Holton

The mining industry has recently been. - experiencing a difficult period. Escalating costs, lower grades and deeper level mining, are a few of .the reasons' why interactive graphics or CADD (computer aided design and draughting) systems are increasingly being used. CADD systems which support powerful and flexible mining applications have great potential for making all forms of mining more efficient and effective. There are many application programs which address almost every aspect of mining. Most of these programs originated to satisfy a particular need. Graphics and other features were added until they, reached a point where they were commercially viable as a mining package. Because of their evolution these packages, lack many CADD-type features. Today there are powerful personal computers (PC's) and engineering workstations running the best CADD systems available. These systems, support hundreds of applications in almost every discipline. Mining was until recently not well supported by interactive graphics vendors because of the highly variable nature of mining and the lack of common standards. Users of CADD systems have experienced the benefits of CADD and come to expect similar features from graphic mining packages. Several developers of mining packagers have either attempted to include some CADD features or make their packages compatible with one or other CADD system. Mining can benefit greatly From a combination of interactive graphics (or CADD) and the right mining application software.

Jan 1, 1989

By Liam Findlay

Optimizing a production schedule with semi-mobile in-pit crushing & conveyance (IPCC) requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout, and truck fleet investment decisions. An integrated stochastic optimization framework is proposed to produce long-term schedules for mining complexes using multiple semi-mobile IPCC systems. The optimizer selects the crusher locations and designs the conveyor routes from anywhere in the mines. The stochastic framework considers simulated multi-element orebody realizations and manages associated risk. A hybrid metaheuristic based on simulated annealing and evolutionary algorithm is implemented for the optimization. The method is demonstrated using an iron ore mining complex.

Jun 25, 2023

By James S. Redpath

INTRODUCTION Background Early in 1972 our firm was asked by Cominco, managers of Arvik Mines Limited, to carry out an underground exploration programme referred to as the "Polaris Project" on a zinc-lead deposit in Canada's High Arctic. We had carried out numerous projects in the far north but this was to be the first long decline driven in perma-frost. Despite the short notice it was possible to meet the quickly approaching summer shipping deadline. We were able to do this by drawing heavily on our own and Cominco's background in Arctic operations. The project was an excellent example of owner-contractor co-operation and this spirit was responsible for the success of the project. Unusual Aspects There were a number of unusual aspects of the Polaris Project which are discussed in this paper. The extremely remote location, the short shipping season, and the fact that the work was carried out in permanently frozen ground, when combined with the lack of handy fresh water and a very severe climate, make it unique in many respects. Despite these handicaps, a record was set during the driving of the exploration decline.

Jan 1, 1974

By J. Bartrum, A. Bowler, G. Butcher

The purpose of this paper is to outline the design, specification, and operation of the 8.5-m- diam (28-ft-diam) SAG mill commissioned at Kidston Gold Mines during January 1985. Amenability of Kidston ore to SAG milling, coupled with substantial cost advantages, led to the specification of this mill, equipped with variable speed drive to overcome the large variation in ore hardness. Operation of the mill is effected via a number of automatic control loops. Problems experienced with automatic control plus other electrical and mechanical failures have led to design changes and the formulation of future operating strategies.

Jan 1, 1987

By Half Zantop

While the Andean belt of Chile contains porphyry copper deposits of considerable economic importance, only one major and several minor deposits of this type have been discovered in neighboring Argentina. There are no obvious geologic reasons for the country's apparent paucity of important porphyry copper deposits. Instead, a lack of exploration because of poor accessibility and past inadequate mining legislation may partly account for this situation. Western Argentina has porphyry copper prospects ranging in age from late Paleozoic to Pliocene. Many of these prospects have host rock and alteration characteristics that are very similar to those of large Chilean deposits. The economic potential of many of these prospects has not been tested adequately by geoehemical, geophysical, or chilling programs. A recently enacted mining promotion law and updated mining code removes some past exploration obstacles in Argentina, and makes in-depth exploration and evaluation of' the county's porphyry copper potential attractive.

Jan 2, 1981

By S. Chander

The mechanism of oxidation of sulfur in pyrite is a function of the rate and driving force for oxidation. New evidence is presented in this article to show that at moderate potentials, a sulfur-rich hydrophobic layer is formed. Under ordinary conditions, the sulfur layer is covered with a layer of iron oxides, hydroxides, sulfate or oxy-sulfide ions. Under these conditions, pyrite is hydrophilic. In the presence of iron-chelating agents or iron sequestering ions, iron layer might not form. Under these conditions, sulfur-layer is exposed and pyritic might become hydrophobic. Stronger oxidizing conditions decompose the sulfur-layer, thereby making the surface hydrophilic.

Jan 1, 1992

By Robert C. Freas

Dravo Lime Company has opened a new 290m (940 ft.) deep lime-stone mine near Maysville, Kentucky. As the mine was opened there were many unknowns as to the stress relationships within the rock, and their influence, if any, on the selected mining method. Therefore, a system of overlay geologic and structural maps, borehold extenso-meter measurements, and oriented photography was developed for the purposes of monitoring the internal structural relationships of the rock mass. This paper presents a description of the methods used, the observations made, and the conclusions and recommendations made as a result of the initial monitoring program.

Jan 1, 1977

By Stephen H. E. Phillips, Michael J. Beus

A pneumatic impact breaker is used to fragment the rock at the shaft bottom, replacing the drill and blast cycle. A backhoe-type mucker removes the broken rock. The operators are in protective cabs below the bottom work deck in the shaft. Preliminary testing has been accomplished at underground and surface test sites in Arizona. Seven, approximately 6.4 m deep by 7.3 m-diameter (21 ft by 24 ft) test holes, (a total of 45 m (148 ft)), were recently excavated in various rock types, including jointed and massive quartz monzonite and rhyolite. An average advance rate of .4 m/hr (1.24 ft/hr) has been achieved. This includes breaking and mucking the rock. Further data is being sought from an in-shaft demonstration.

Jan 1, 1981

By Reno M. Tonsi, Bill Raley

Supervisory Control and Data Acquisition (SCADA) systems are important tools in providing more efficient and profitable operations for the mining industry. This paper touches on the different types of equipment used in SCADA applications and discusses the benefits obtained in using Programmable Logic Controllers in this application.

Jan 1, 1989

By T. Wisdom, D. Romo, G. Seale, R. Jansen

Thickening remains relatively misunderstood since it is typically near the end of the process and not directly involved in metal recovery. When operating well, thickeners are ignored and left to run independently, the ‘out of sight, out of mind’ phenomena. However, when operating poorly, there is a lack of basic understanding and remedial actions to solve issues are reactionary rather than proactively addressing shortcomings. This series of papers breaks down in sequential order the stepped phases required to gain an appreciation and thorough understanding of the science behind thickeners, and key thickener components, and basic troubleshooting skills. This second paper starts with identifying the different approaches to thickener test work including static and dynamic settling tests followed by high-rate versus paste thickening. Complimentary to test work, the mechanisms surrounding coagulation and flocculation are presented and explained. The basic mechanisms for coagulation and flocculation are discussed to support the different test work approaches and provide the reader with the basic background.

Mar 2, 2022