Search Documents

By R. E. Muller, L. G. Martin, J. M. Stonehouse

Erratic distribution of values in free gold ore bodies presents severe problems in sorting material in large scale open pit mining. However, an intense program of modern blasting techniques and less than modern gold panning results in good sorting at Houston International's Manhattan mine. Blasting technique is important. If the sample location cannot be relocated because of blasted material movement, information acquired while drilling is useless. So short benches are critical to minimize dilution. Though not very accurate, panning allows for rapid analysis. The more accurate fire assay does not provide the needed speed. Panning can be fairly accurate and errors made are mostly on the low side. Samples of mixed and broken stockpile material are used as checks on pit procedure and to develop stockpile content in¬formation. Added tonnages discovered offset the higher labor costs of this careful sorting technique. The mine is located in central Nevada's Toquima Range in the small mining town of Manhattan, 322 km north of Las Vegas. The mine has four epithermal stockwork ore bodies that are mined in two pits. The mine problem was that conventional ore control was not separating ore from waste. Assays of 6-m blast-holes were used on 5-m centers. The blastholes were relocated by stadia survey after blasting. Holes assaying above the cutoff grade were flagged and mined as ore. This system is practical and useful in high concentration ore bodies or in evenly disseminated mineralization. But it was not practical at Manhattan because of large gold particles and small ore pocket sizes. Ore pockets were often missed when drilling a grid area for blasting. Also, large gold nuggets made assay results unreliable. The probability of a nugget being contained in an assay charge is small. So most results were low, compared to actual grades mined based on stockpile samples. When a nugget found its way into a fire assay charge, the result would be far higher than the actual grade of material represented. In addition, disturbance by blasting created problems in relocating ore. Because of these problems, the grade control program was intensified in September 1979. It successfully separated ore and waste in blocked out ore areas and located more ore in "waste" areas. Known reserves mined to date have increased up to 50% on some benches. The methods used are modern blasting techniques, detailed assaying, and traditional panning of samples collected from active mining faces. These methods allow mining flexibility, to match the variable mineral occurrence in ore bodies. The united effort of the geology and engineering departments has been important to the program's success.

Jan 12, 1980

By James M. Prudden, Jon C. Sprague

Valdez Creek Mining Co. properties consist of multiple intersecting paleo-placer channels containing appreciable quantities of coarse gold. Reverse circulation drilling, combined with geophysics, is used for both exploration and development reserve determination. Classical drill-blast-load-haul open pit mining techniques used for the 22,000 cubic yard per day production schedule required modification to compensate for arctic winter operating conditions. High wall stability problems within the glacial sediment overburden necessitated developing multiple dewatering methods and variable pit slope designs to eliminate unstable pit wall conditions. Processing mine run fluvial gravels utilized a classical winter protected screening plant-sluice box recovery system enjoying high metallurgical recoveries and zero discharge tailings disposal.

Jan 1, 1987

By H. M. Lima, P. Wathern

There are many different words to describe mine closure, including rehabilitation, reclamation, restoration and decommissioning. Closing mining operations, mainly open pit mines, has required resolution of numerous issues. Mine closure plans involve environmental-protection issues, regulatory issues and community issues. The obvious, and often most expensive of them, is the physical rehabilitation of the disturbances and the elimination of long-term commitments and maintenance. This paper outlines mine closure planning and its important component, mine-site rehabilitation. Community consultation and involvement are also referred to as an important component of the mine-closure plans, which are required to ensure satisfactory mine site rehabilitation. Considerations of socioeconomic impact of mine closure and long-term responsibilities are presented.

Jan 1, 2000

By L. W. Saperstein, MJ. Carlson

With the goal of improving the strength characteristics of pneumatically emplaced material used for localized subsidence control, the binding additives fly ash, bentonite, and portland cement were examined for their effect on the support capabilities of coal refuse. It was found that, within certain concentration ranges, all three offered some increase in the ultimate strength of the backfilling mixture. However, portland cement gave the greatest percentage increases. Selection of the appropriate backfilling mixture will allow for the most economical and efficient subsidence control when pneumatic stowing is employed.

Jan 1, 1990

By B. A. Hancock

It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rup- ture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differ- ences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding- classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective floccula- tion separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 1, 1987

By R. J. Gochin, G. D. Schena

Mineral processing options and technical innovations should be financially assessed. Indeed technical feasibility alone does not offer an adequate process selection criterion. An appraisal by the use of engineering economics principles leads to a more efficient evaluation and selection of feasible mineral processing solutions. Financial consequences of different options synthesised by profitability indices allow better decision making. Selected examples derived from real world problems are used to illustrate the potential of engineering-economics methods applied to mineral processing.

Jan 1, 1995

By A. F. Symonds

The effects of harmonic resonance between the supply impedance and power factor correction capacitors on systems with large harmonic sources, such as mine winders, are well known. The similar effects of resonance with cable capacitance are not commonly encountered and, hence, are not always considered in the design of medium-voltage networks. This article considers some of the aspects of resonance between the supply impedance and the cable capacitance and presents one successful approach to solving the problem.

Jan 1, 1998

By J. G. Groppo, B. K. Parekh

Column flotation testing was conducted on the flotation feed slurry obtained from a preparation plant located in the Southern Illinois coal basin. The column flotation tests were conducted using three different bubble generating devices: a static sparger, a gas saver and a foam jet. Each of these devices was tested with three different types of frother and various column operating variables to provide maximum combustible recovery, minimum product ash and maximum pyrite rejection. The results show that column flotation provided improved flotation performance, in terms of combustible recovery as well as ash and pyrite rejection, for each of the bubble generating devices. However, the effectiveness of each bubble generating device was dependent on the type of frother used. Alcohol frothers were most effective for use with the static sparger, somewhat less effective for the foam jet and ineffective for the gas saver. Glycol frothers were effective for all three bubble generating systems, providing high combustible recovery (>90%); low clean-coal ash (4-6% ash) and high pyrite rejection (70-80%).

Jan 1, 1994

By Y. A. Attia, D. K. Sengupta, H. A. Hamza

Increased recycling of waste paper has been emphasized in recent years in both the United States and Canada for environmental and economic reasons. Removal of ink particles from waste paper pulp is therefore necessary. One of the most promising methods for ink removal is froth flotation. This study investigated the feasibility of a simplified flotation scheme and found that about 90% to 92% ink removal can be achieved. Also, a 95% to 97% ink removal is achievable if a hydrophobic polymer is used ahead of the flotation stage. Clean paper pulp recovery was over 90%. The effects of pulping pH, flotation pH and concentrations of flotation and polymeric reagents are discussed in the paper.

Jan 1, 1995

By Wm. Randolph Reed, John A. Organiscak

Haul trucks have the potential to generate large amounts of respirable dust. This respirable dust has been shown to be a health hazard to personnel, especially if it contains a high silica content. Lack of dust sampling data from haul trucks prompted the completion of a study to quantify respirable dust concentrations. These field studies were conducted measuring instantaneous respirable dust at stationary locations from passing haul trucks at a stone quarry and a coal mine site. Fugitive dust levels from haul trucks were analyzed to characterize dust dispersion. This analysis will indicate safe following distances for haul trucks and other heavy equipment to avoid over-exposure of respirable dust from the lead haul truck.

Jan 1, 2005

By Myles P. Reilly, Randall A. Snowdon, John Temporal, O&apos

The paper describes studies made at the Transport and Road Research Laboratory, UK, of the mechanical cutting characteristics using disc cutters, of rocks with compressive strengths up to 340 MPa. These studies have been performed in both the single pass mode, where interactive breakout occurs between adjacent grooves on every pass of the tool, and the multiple pass mode, where several passes may be required to cause breakout. In addition, experiments to determine the effect on cutting performance of the hydraulic stiffness of tunnelling machines are described. The results of these tests are analysed and discussed in the context of the design of full-face tunnelling machines.

Jan 1, 1983

By Changhong Huang, Y. J. Wang

This paper describes the formulation of mine ventilation network optimization as a standard nonlinear programming problem and the solution of the problem using the generalized reduced gradient (GRG) method. In general, the GRG method is regarded as one of the most effective and efficient methods for solving large-scale nonlinear programming problems. The variables considered in the network optimization include air quantity, regulator pressure loss, and fan pressure for each branch. Each of the variables is constrained by lower and upper bounds. This facilitates proper assignments of ventilation requirements and provides a great flexibility to include various situations encountered in mine ventilation. The objective of the network optimization is to minimize the overall air power consumed by or supplied to the network; whereas the constraints are, in addition to the variable bounds, the two fundamental network laws: Kirchhoffs voltage law and Kirchhoffs current law. A computer program has been developed based on the GRG method for the network optimization. An example of network with 18 branches, 8 regulators and 3 fans is included for illustration.

Jan 1, 1993

By Louis G. Silano, Aram Grigoryan

Parsons Brinckerhoff is providing engineering services for the Atlantic Avenue Station Complex Rehabilitation and Passageway Reconstruction for New York City Transit. Project reflects current realities and challenges of underground excavation, support, and construction under operating subway tracks and platforms, and under major transportation hub, comprising three subway stations, railroad terminal station, and busy street intersection. The construction requires extensive underpinning of subway structures and operating tracks. This Paper addresses engineering challenges of IRT subway station rehabilitation and passageway reconstruction without interruption of transit operations and street traffic. Total construction cost of the Project is $ 105,000,000.

Jan 1, 2003

By Brian H. Kaye

Efficient design of grinding circuits for efficient production of ultrafine material requires rapid feedback of information concerning the fineness of material leaving the grinding device Generating this information requires efficient sampling and adequate rapid characterization of the material leaving the grinding machinery Recent developments in electrooptic inspection of dry and wet material leaving a grinding device are critically reviewed New methods for characterizing ultrafines are discussed A rapid operating automated cybernetic (intelligent) permeability device for automatic control of grinding circuits using Blaine Index and other fineness indices is described

Jan 1, 1983

By Daniel H. Stevenson

Safety and health are fundamental values at Barrick Goldstrike. An effective safety and health program protects employees, controls costs and increases productivity. Barrick Goldstrike believes that all occupational injuries and illnesses can be prevented and that safety must be the responsibility of every employee on the property. Safety and health must be thoroughly integrated with the company's efforts to maximize production at the lowest reasonable cost. The goals of safety and production are not mutually exclusive. They must work together to achieve safe production. Barrick Goldstrike began to mine the Betze deposit in 1987. From 1987 to 1992, Barrick employed a traditional safety system using safety specialists on each crew. These specialists were responsible for ensuring that the work areas were safe and that employees were properly protected and trained in safe work procedures. As the work force increased, it became apparent that this system was not the most effective method of ensuring safe production. In 1992, Barrick Goldstrike implemented a loss control program. It was modeled after the International Loss Control Institutes's (ILCI) International Mine Safety Rating System. This program was based on the philosophy that safety is a management responsibility. It can be managed in the same manner that production and cost issues are managed. Under the loss control system, safety needs are identified and evaluated. Programs with performance standards are developed and implemented and the activities and results are regularly monitored. Between 1992 and 1996, Barrick Goldstrike worked at developing and improving its safety management systems. These efforts had a positive return. The incident rates began to decline as these improved systems were implemented. Studies were undertaken in early 1996 to evaluate the effectiveness of the safety and loss control programs in reducing accidents. The studies showed a strong correlation between the implementation of the loss control programs and the resulting reduction in all accidents. Studies in the process division revealed that Barrick had experienced reductions in personal injury accidents from the projected number that could have been expected had no changes been instituted. These reductions ranged from 39% in 1993 to 59% in 1995. These reductions from the projected rates held true for all types of accidents; personal injury, property damage and Mine Safety and Health Administration (MSHA) reportable.

Jan 1, 1997

By R. A. Jankowski

Laboratory tests were conducted to evaluate the silica collection efficiency of flooded-bed scrubbers using six different filter panel designs at two operating velocities. Test results indicated that reductions in filter density negatively impacted respirable dust collection. Silica collection efficiency for the least-dense filter was as much as 33 % lower than the collection efficiency of the most-dense filter. At the low operating velocity, the least-dense filter allowed more than 40% of the respirable silica dust in the scrubber intake air to pass through the unit and back into the mine environment. Operation of the scrubber at the higher test air velocity increased silica collection efficiency regardless of the filter panel tested The density of the filter panels also impacted the quantity of air moved through the scrubber, with higher-density filters reducing scrubber airflow. For each filter, the relationship between dust-collection efficiency and air-moving capacity must be considered to determine the overall effectiveness for each mine application.

Jan 1, 2000

By Daniel R. Hack

Mine planning software companies have recently focused some resources on the development of industrial minerals packages useful in the aggregate industry, which is years behind other mining industry sectors in the use of computer-based planning techniques. This paper presents and compares characteristics of aggregate / quarrying software packages currently on the market, each product having strengths beneficial under different circumstances. To be successful, the developers must confront the limitations of their packages under a variety of situations, address the unique characteristics of the aggregate industry, and pay particular attention to the applicability of their products in real situations.

Jan 1, 2002

By D. E. Ranta, M. G. Schulz

Mining of Molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the orebody. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1992

By John B. Comer

Compelling evidence indicates that at least the plateau bauxite of northern and central Jamaica formed from volcanic ash. The predominance in plateau bauxite of zircon grains younger than the host limestones and the relative abundance of zircon grains having idiomorphic form support a direct ash-fall origin for much of the bauxite parent material. Based on revised mass balance calculations, not enough of the middle Eocene to lower Miocene host limestones have been dissolved to make an important contribution to bauxite. Likewise, the pre-middle Eocene rocks of Jamaica have made only a very small contribution to plateau bauxite; they may have made a more significant contribution to the graben bauxite of southern Jamaica.

Jan 1, 1984

By M. Kumral

The in-situ mineral characteristics of a deposit are simulated by sequential co-simulation and averaging the simulated characteristics within specified block volumes creates a three-dimensional block model. This model is then submitted to optimal open pit and production scheduling algorithms. As the market values of industrial minerals depend on the satisfaction of predetermined blending criteria rather than metal content, a Linear Programming (LP) scheme has been used to identify all blocks that can be included in the blend without violating the grade requirements. The Lerchs-Grosmann algorithm using the blocks identified by the LP program determines optimal pit limits. All blocks that lie outside the optimal pit are removed from the system and the blocks within the optimal pit are submitted to the production-scheduling algorithm. Production scheduling optimisation is done in two stages: Lagrangean parameterisation, resulting in an initial sub-optimal solution, and multi-objective simulated annealing (MOSA) improving the sub-optimal schedule further.

Jan 1, 2002