Search Documents

By Brain W. Lawrence

Sublevel stoping generally is a large-scale open stoping method. It sometimes is referred to as long-hole or blasthole stoping. This method usually is applied to strong ore bodies that require minimal support and are surrounded by strong country rock. The ore body should be fairly regular in shape and well-defined. The dip of the footwall normally should be sufficient to allow broken ore to gravitate freely, although the method has been adapted successfully to mine some of the flatter ore bodies. Sublevel stoping is not dependent on the width of the ore body. Widths of less than 6 m (20 ft), however, make the utilization of long-hole drilling techniques more difficult. The main criteria for sublevel open stoping are competent ore and stable host rock, regular ore boundaries, and a footwall dip that exceeds the angle of repose of broken ore. Basically, the method entails providing access to the ore body at various subintervals between the main haul- age levels in order to drill and blast the intervening ore. Stope drilling is carried out from drilling drifts on the sublevels, and the ore is blasted in slices towards an open face, which generally is vertical on the downholes and may be inclined towards the open face for the up holes. The blasted ore gravitates to the bottom of the stope and is collqcted through drawpoints. Fig. 1 illustrates a typical sublevel stoping mine. The method requires extensive ore body development with relatively high capital expenditures. How- ever, much of the development is in ore, and production costs are comparatively low. Productivity rates are in the 13.6 to 27.2 t (15 to 30 st)/manshift range. The drilling, blasting, and loading operations are performed independently, and equipment utilization is high. Large outputs can be obtained with few units and limited personnel. Dilution with waste rock may occur if ore boundaries are irregular or if caving occurs, but 100% of the ore within the stope usually is recovered. Pillar recovery sometimes is a problem. It is at this point that most of the waste dilution occurs. At the time data was gathered for this report (1973), the sublevel open stoping method was used by more than 21% of the metallic ore mines in the US (9 out of 42 mines producing 1088 + t/day (1200 + stpd) and provided more than 12% of the total metallic ore production from these mines. DEVELOPMENT Access to a sublevel open stope mine is gained by a slope or shaft that is normally sunk in the footwall of the ore zone, away from any possible effects from blasting or other production operations in the stoping process. Main level interval is selected and usually varies from 45.7 to 121.9 m (150 to 400 ft), depending on the vertical extent of the ore body, the number of drawpoints required to maintain output, and the eventual stope height. The main haulage drifts are located at the bottom of the stope horizon, either directly in ore or in the footwall, with access crosscuts at intervals. Raises are driven up through the ore to connect to the level above and provide access and ventilation to the sublevel drilling drifts, which are driven horizontally in the ore for the length of the stope. Depending on the drawpoint system to be used, the stope is either undercut by a raise-and-cone system, from a scram or slusher drift, or simply provided with a drilling drift from which access is made at intervals to the main haulage level. A raise driven either at the end or in the middle of the stope (if stope access is from both ends) provides a start for opening up a vertical slot across the stope to establish a free or open face for long-hole drilling and blasting. Sublevel stoping has proved to be a relatively safe and economical system.

Jan 1, 1982

By Kenneth R. Dickson, I. Michael Gowring

This paper describes the underground work associated with the North Fork Stanislaus River Hydroelectric Development currently being constructed by Sierra Constructors for the Calaveras County Water District in California under a turnkey contract. Sierra Constructors is a joint venture of the Guy F. Atkinson Construction Company (sponsor) of South San Francisco, and the Harrison Western Corporation of Denver. Notable features of this project include the exceptionally high performance achieved by the 5.5m diameter Robbins tunneling machine and the 675m deep shaft pilot hole which was successfully realigned using oilfield directional drilling techniques. Other features include 3.7m and 4.3m diameter machine-excavated tunnels and various conventionally excavated tunnels constructed over a wide geographical area and diverse climatic conditions.

Jan 1, 1987

By D. Lelinski, X. Nie, J. D. Miller, J. Hupka, K. Bukka

A preliminary characterization of soil components contaminated at a low level (7 nanocuries per gram) with toxic/radioactive metals has been carried out. Most radioactivity and metals content were present in the minus 100 mesh (<150 µm) size fractions. None of the size fractions examined qualified for uncontrolled disposal at dump sites, thus all material would have to be moved to discharge-controlled landfills. The metal content of the sample was below the limits for economical recovery, therefore eventual processing would be dictated by environmental concerns.

Jan 1, 1992

By N. D. Cristescu

An analysis of the interaction between a creeping rock and a yieldable lining is presented. The following cases are considered: an elastic lining, a lining made of circular shaft rings that may slide at their joints, a lining made of circular reinforced concrete panels with wooden compressible strips inserted between the longitudinal joints and a yieldable support that has a compressible broken-rock stratum between the support and plane rock. By formulating a mathematical model for the rock-lining interaction, one can optimize the sequence of excavation-lining application. To keep costs to a minimum, one can also choose the most appropriate lining for the corresponding rheological properties of the rock.

Jan 1, 1997

By Y. Q. Zhang, Y. Luo, S. S. Peng

Burrier pillars in underground coal mines could eventually be subjected to a water head due to the build-up of mine water in the old workings. The water head could not only act ns a force to destabilize the pillar, but it could also cause seepage flow through the pillar and its surrounding strata. Excessive seepage flow could induce piping failure that, ill turn, could accelerate the mechanical failure process of the barrier pillars. In this paper, a finite element simulation approach was employed in the evaluation of the barrier pillars. Both the stress distribution and the seepage flow pattern in and around a barrier pillar have been simulated numerically. The effects of ground stress on rock permeability to water seepage has been taken into consideration in these simulations,

Jan 1, 2002

By W. S. Versluis, G. W. R. Kuzyk

Atomic Energy of Canada, Ltd. (AECL) is constructing an Underground Research Laboratory (URL), a major component of-the Canadian Nuclear Fuel Waste Management Program. In July 1988. AECL and the US Department of Energy commenced a cooperative research program that included extending the URL shaft by 190 m (623 ft) to the 443-m (1,453 ft) depth. The shaft extension, 4.6-m- diam (15-ft-diam), was excavated by full-face blasting using a burn cut. A Galloway stage accommodated the research activities and the sinking contractor&apos;s requirements. Blast designs incorporated controlled blasting techniques to minimize blast-induced damage on the shaft walls. The full-face method has been very effective, with 3.5-m (11.5-ft) rounds being advanced.

Jan 1, 1990

By S. Nickson, M. Grenon

Oriented borehole data provide the means to characterize a rock mass. In this paper, the geomechanical caving potential of a hard rock mine project is investigated. In particular, the influence of random joints to the resulting block size distributions is addressed. The implications of this approach in preliminary investigations on the choice of mining methods are discussed with reference to one site.

Jan 1, 2003

By Neville G. W. Cook, John Kemeny

Utilizing the principles of elastic-brittle fracture mechanics, stress-displacement relationships are derived for an elastic solid containing a slip plane consisting of various configurations of collinear arrays of cracks. These models take into account the heterogeneous nature of slip planes as observed in the lab and in the field, and are relevant to the behavior of rock containing faults, joints, bedding planes, and fractures. All of our models exhibit slip weakening behavior, and show regimes of both stable (aseismic) and unstable (seismic) deformation. For given configurations of cracks and applied boundary conditions, our results show explicit ly the energy released through unstable crack growth. For instance, it is found that two equal length cracks growing together release more seismic energy than, say, a large crack growing into a small crack. Also, by allowing cracks to coalesce, our models show multiple stick-slip events without crack healing or other geochemical means.

Jan 1, 1986

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By O. Alvarez-Campos

Two porphyry copper orebodies, the North and Central MM orebodies, have been found through regional and structural geologic works, about 5 Km south of Chuquicamata, under a gravel bed of approximately 100 m and in the west side of the West Fissure. The mineralization is emplaced in a coarse granodioritic porphyry, predominantly with sericitic alteration. In the North MM ore-body, with 200 million metric tons of 1.0% Cu, the mineralization is mainly chalcopyrite, bornite, digenite and molibdenite. In the central MM orebody, with 700 million metric tons of 1.3% Cu, there are large veins of enargite, chalcocite and bornite, the last one increasing in depth, separated by chalcopyrite and pyrite zones; in these veins there are interesting gold and silver values. Both orebodies have an upper enrichment of chalcocite and covellite, with pyrite envelope. According with these characteristics, the MM orebodies could he the upper part, with sericitic alteration, of the Chuquicamata porphyry copper system, displaced by the West Fissure system movements, but we couldn&apos;t eliminate the possibility that MM can be a new orebody, different of Chuquicamata.

Jan 1, 1993

By J. F. Able, F. Djahanguiri

The US Bureau of Mines conducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1998

By Michael L. Nave

Mining belt conveyor elements are becoming larger and more expensive. Conveyor reliability requirements are rising. Conveyor condition monitoring can aid maintenance, reliability, and risk management in conveyor system operation. This paper examines the application of condition monitoring in coal mining belt conveyor systems. Types and form factors of condition sensors are described. Example costs are included. Suggestions for OEM developments are examined. Application problems are discussed. Two simple cost case studies are presented.

Jan 1, 2000

By Robert A. Haney, Richard T. Stoltz

In July, 1988, the Mine Safety and Health Administration (MSHA) Advisory Committee on Standards and Regulations for Diesel-Powered Equipment in Underground Coal Mines recommended that the Secretary of Labor set in motion a mechanism whereby a diesel particulate standard can be set. Prerequisite to establishing a standard would be the development and evaluation of instrumentation to measure diesel particulate. In response, the Mine Safety and Health Administration, Dust Division, has been evaluating instrumentation that can be used to determine diesel particulate levels in underground mines. This instrumentation employs the principle of impaction to separate particles by size, thereby, separating the diesel and nondiesel particulate. Separation of the particulate by size was chosen because diesel particulate is generally less than 1.0 micrometer in size. No other methods have been developed to successfully distinguish between the coal and diesel particulate. MSHA developed an impactor that is inexpensive and compatible with existing pumps and filter holders. The instrumentation evaluation has primarily focused on the repeatability and performance of several personal dust samplers. The samplers tested include the Sierra-Andersen Model 298 personal impactor and MSHA developed personal impactor. The MSHA impactor is inexpensive and compatible with the existing pumps and filter holders. In addition to evaluating the precision and performance of these instruments, tests have been conducted to determine background levels of submicron particulate in nondieselized coal mines and to measure the submicron particulate content in dieselized coal mines. Tests were conducted in coal mines where diesel equipment was used only in outby areas and also in coal mines where diesel equipment was used for face haulage. This paper describes the results of the tests and provides a description of the instrument at ion used to conduct the tests.

Jan 1, 1989

By K. S. E. Forssberg, M. I. Hallin

In many cases, the reuse of process water in flotation plants is desirable both for plant operating reasons and for environmental protection. The main advantages are better housekeeping of fresh water and process chemicals together with the reduction of polluting species to the environment. There are however a number of problems involved in the use of recycled process water. The main problem is that recycling sometimes has a deterious effect on the process and can occur months after the start of water recycling. The Division of Mineral Processing of Luleå University of Technology has been conducting experiments on recycling of process water at various sulphide plants in Sweden for over ten years. The experiments have been carried out in pilot- and full industial scale, in collaboration with the mining companies operating the plants. Until 1988 investigations were carried out in four different sulphide plants. The objectives of the experiments were: first to document differences in the composition of the process water during recycling; secondly to investigate any changes in the pulp chemistry of the flotation circuits wich may be due to the influence of recycled water; and lastly to establish critical levels, if any. of the parameters measured. While conducting experiments of this kind several things have to be kept in mind. Normally, recycling is done by using tailings pond water as process water. This means that time effects are important, because of the time lag between water input in the tailings pond and the reclaim of that water back to the plant. As will be shown, the

Jan 1, 1989

By W. D. Monaghan, A. J. Kwitowski, A. L. Brautigam

Teleoperation is a technology that can provide significant health and safety improvements in mining operations by locating machine operators hundreds of meters away from the face area. The US Bureau of Mines recently developed a teleoperation system for continuous mining and haulage equipment. This system features near real-time closed-loop control. A prototype system was developed and demonstrated. This system could be used in thin-seam applications down to 36 in (914 mm). Provided are details of the teleoperation system, the results of testing and the expected applications of this technology.

Jan 1, 1996

Bismuth, "the green metal," has become an important substitute for lead. The uranium industry was never really dead, anti-nuclear activists just wanted the world to think it was. And diamonds are fast becoming a miner&apos;s best friend. These commodities and others were discussed in May 1997 at the 47th Annual Minerals Processing Division meeting, held at the Broadmoor resort in Colorado Springs, CO. The meeting was put on by the SME Colorado subsection and was attended by about 115 people. In addition to the above three commodities, attendees learned more about the state of the copper industry, as well as lead and zinc and gold and silver. The program also included discussions of molybdenum, platinum and project financing. The following is a summary of some of the presentations.

Jan 1, 1997

By M. J. Laurila

Utilizing data compiled from a drilling program and bulk samples taken from a coal reserve, flowsheet performance for a coal preparation plant can be calculated using a desktop computer. Sets of equations defining material balances involving coal preparation plant unit operations are employed to depict plant performance. Techniques are discussed for interpolating washability data and extrapolating size distributions and other critical data to expand on oftentimes limited sets of quality data to a useable data base from which projections can be made. Simulation of flowsheets can be done for a number of different conditions and configurations while still remaining in a limited working memory capacity of 32,000 bytes. Presented within this paper are several pertinent examples.

Jan 1, 1982

By Kang-Hyun Lee, In-Mo Lee, Byung-Kyu Kim, Parkm Jinho, Seoung-Won Lee

"In this study, the TBM Resistivity Prediction (TRP) system is developed for predicting the location, thickness, permittivity ratio and electrical conductivity of anomalous zones ahead of tunnel face using the measured resistivity of the ground. The applicability of the developed system was verified by performing field tests at a construction site in which an EPB-shield TBM is used for tunnelling work. In the first field test, it was found that the rock around the tunnel face had the same resistivity and permittivity with the rock ahead of the tunnel face indicating no anomaly ahead of the tunnel face. In the second test, a stronger zone 5-m thick was predicted ahead of the tunnel face based on lower permittivity than that of the rock around the tunnel face. The ground condition assessed by the newly developed TRP system matched well with that either predicted from geophysical exploration or directly obtained from drilling boreholes or from daily observed muck conditions. INTRODUCTION During tunneling work, the emergence of unpredicted zones of relatively weaker or stronger ground can lead to delays in construction work or an increase of construction cost. Predicting anomalous zones ahead of tunnel face in advance can thus prevent time and economic loss. For these reasons, various methods to predict the ground condition ahead of the tunnel face have been studied and developed. Prediction methods using various kinds of equipment include tunnel seismic prediction, ground penetrating radar, electromagnetic surveys based on electronic antennas, and electrical resistivity surveys conducted by analyzing electric currents in the ground ahead of the tunnel face (Ryu et al. 2008). However, most of the prediction methods are only applicable to conventional tunneling job sites, which feature free access to the tunnel face. In mechanized tunneling projects, accessibility to the tunnel face is very limited because the tunnel face is occupied by the TBM."

Jan 1, 2016

By M. E. Kuchta

Research is currently being conducted at the Colorado School of Mines in the use of high-pressure water for scaling down loose rocks in underground mine openings. In addition to improved miner safety, the adhesion strength of shotcrete applied to rock surfaces treated with high-pressure water is also increased significantly, resulting in improved overall support capabilities of the shotcrete layer. Test results show an increase in adhesion strength by a factor of four on a concrete test wall cleaned with water at 21 MPa (3,000 psi) as compared to a surface cleaned at 0.7 MPa (100 psi).

Jan 1, 2003

Stratabound uranium deposits consist generally of two comingled geologic and statistical populations. Barren zones, usually having radiometric assays too low for recording on digitized logs, comprise a large portion of a mineralized stratum. In between are mineralized zones; where the grades are distributed essentially lognormally. Estimation of open-pit ore reserves requires the prediction of the tonnages of selective mining units (the smallest mined volume which may be segregated as ore or waste) and their grades within panels of convenient size for open pit planning and economic analysis. The proportionate tonnage of mineralized selective mining units within each panel can be predicted by kriging an an indicator function assigned to each composite (1 if mineralized, 0 if barren). Next, using logarithms of mineralized assays, the conditional lognormal distribution of grades of mineralized selective mining units can be found. Using this distribution and the krigedestimate of the probability a selective mining unit is mineralized, the grade and tonnage of selective- mining units above any cutoff can be predicted. A case study illustrating this two- step procedure is presented for the Imouraren uranium deposit located in the Republic of Niger. Using cross validation, the estimation procedures were checked and were shown to be adequately accurate for mine planning purposes.

Jan 1, 1979