Search Documents

By Robert G. Moorhead

Fine-coal screening can be one of the most critical operations in a modern coal-cleaning plant. The yield and quality of clean coal produced in fine-coal circuits is controlled as much by how efficiently 0.15 mm (100 mesh) particles are sized as on the performance traits of the fine-coal cleaning device itself. In addition, the increased interest in effective fine-coal sizing operations indicates that many operators have also discovered its importance in affecting the quality and yield of clean coal produced in fine-coal circuits. This paper describes the three most prevalently used fine-coal screening technologies and discusses their sizing mechanism, performance, and application.

Jan 1, 1988

By Naj Aziz

Both bolt profile shape and spacing (rib spacing) have been found to influence the bonding capacity of the grouted rock bolt. The bolt surface profile configuration has greater importance to rock bolting in strata reinforcement in mining than the steel rebar used in civil engineering construction. This is because a rock bolt in mining usually is subjected to greater dynamic loading than the steel rebar in civil engineering construction. The increased bonding capacity of a bolt is important when supported ground is either heavily fractured, faulted or the supported ground is of soft formation, typically that of coal measure rocks. Past laboratory studies have identified the bolt profile spacing as of significant relevance to bolt resin rock bonding increase, however, no attempt has been made to determine the optimum spacing between the bolt profiles spacing. Accordingly, a series of laboratory tests were carried out on 22 mm core diameter bolts, commonly used in Australian mines, installed in cylindrical steel sleeve. The study was carried out using both push and pull testing methods. The push test was carried out in 150 mm long sleeves while the pull testing was conducted in 115 mm long sleeves. Profile spacing tested include, 12.5, 25.0, 37.5, and 50 mm lengths. Additional studies undertaken include modelling the profile of the load-displacement data of pull testing. Bolts with a profile spacing of 37.5 mm were found to provide optimum load bearing capacity as compared to other tested profile spacings.

Jan 1, 2009

By G. Milojcic

The opencast lignite mines in the Rhinel and Di strict/Germany are equipped with the continuously operating bucket-wheel excavator - conveyor - spreader system. High productivity requires large capital expenditure on main mine equipment as a precondition for efficient mining. In operation, the technology employed leads to a particular cost pattern which is quite different from that of other industries. Labour, auxiliary equipment and mobile vehicles are the most important cost factors which can be controlled by the management. In this respect information processing computer systems are used for systematical and interpretable representation of operational tasks and jobs both in planning and work preparation and in recording the operational data describing the work result and the use of resources. Another aim of the project is to relieve the middle management of major part of its administrative routine work. Job-related work planning and data recording open up various possibilities of analyzing the operational procedures. This analysis shows, for example, what auxiliary machines are particularly suitable for specific tasks, and working groups can be organized so as to take account of the different skills of individual employees for the sake of an optimal work product. Computerized information processing provides the decision makers with topical information related to their respective responsibilities. The mining department of the Hambach opencast mine is the first user of the PERMAD system. Due to the favorable evaluation it has been decided to introduce PERMAD in three other mines in the course of 1992/93.

Jan 1, 1992

By Y. K. Yen

The most serious problem for on-line coarse particle size measurement from a conveyor belt by image analysis is the overlap phenomenon that occurs between adjacent particles. A methodology is developed and described in this paper to estimate the sieve size distribution from the overlapped projected particle images as might be obtained from a conveyor belt. Two aspects of the overlap problem have been taken into consideration. First, several image processing algorithms were studied to find the most suitable technique to separate the projected overlapped particle images for narrow sized particles. These image segmentation algorithms include two-dimensional thresholding, edge detection and Watershed discrimination techniques. The other aspect of the overlap problem is related to the determination of the general kernel function for the partial particle images obtained from the projection of the overlapped particle bed. In this regard, a computer simulation technique was applied to mimic the overlapped particle bed for narrow sized particles, then the general kernel functions of the partial particle images were determined.

Jan 1, 1994

By Graham A. Mathieson

A detailed breakdown of capital and operating costs is an essential element in the planning and evaluation of any mining project. The OPCOST System was developed by Golder Associates to provide mining engineers with the facility to synthesize detailed cost estimates for all aspects of an operating or potential open pit mine. The system can also be applied to underground mines equally as well. Such estimates can be prepared at a variety of levels depending on the detail required by the project. The OPCOST System is a suite of computer programs linked through a common hierarchical data base. It simulates the thought and reasoning processes within the quantity takeoff and cost estimation phases of a mining project. The system was developed as a mining cost engineering tool on the basis that it would have to satisfy a variety of purposes, namely:

Jan 1, 1982

By R. Perlo

"INTRODUCTION Peoples’ and operators’ safety in construction are tightly linked to the engineering choices, as much as the necessity of reducing time and costs of realization. Therefore, it is of paramount importance to address them properly from the earliest stage of the design, identifying the risks connected to the work and the variability of such during the different phases of the project. Risk is often measured as the expected value of an undesirable outcome. Regarding to occupational safety and health, the risk is the likelihood that a person may be harmed of suffers adverse health effects if exposed to a hazard. This combines the probabilities of various possible events and the assessment of the corresponding harm into a single value. However, the actual occurrences are often more complex than a single binary possibility case. In a real case scenario, with several possible accidents, the total risk is the sum of the risks for each different accident, provided that the outcomes are comparable. The semi-automatic tunnel support system along with its erector machine proved to be a solution with improved structural performance, able to reduce the time and yet to deliver an enhanced, quality-aware and safer working environment for the operators. The implementation of the system provides the engineers, the contractors and the owners with an effective alternative option shortlisted in 2015 for the ITA Award for the Safety Innovation of the Year. In a market industry driven by safety and time constrains the efficiency shall be the ultimate goal, in order to provide solutions able to negotiate with the most challenging ground conditions. In this paper, the authors describe the recent developments on regard of this whole new tunnel support system, including design approach and presenting related case histories OFFSETTING THE RISKS Considering the above factors, from the manufacturers’ point of view, an effective way to limit the construction risks is to focus on the material and technological characteristics, their application and the risks related to them including any residual risks. Finally addressing the construction needs also involves time and cost-effective solutions. The path to follow is an integrated approach where the efficient management of the risk is supported by a flexible, user-friendly, and time effective product that is able to provide a safe, reliable and viable solution to address the construction requirements. Therefore, in a market sector driven by safety and time constraints, the efficiency is a key goal, in order to avoid redundancy and yet to deliver a safe working environment able to meet the construction schedule. The safety of all the parties involved is given by stable working conditions, either for the workers, or the operators and eventually the public. Therefore, the solutions provided should ‘strengthen’ the overall condition and such “to limit or to reduce the deformations within acceptable designed limits and to prevent [the tunnel] to collapse” [1: Clause 207.1.4]."

Jan 1, 2018

By A. S. Trimble, J. C. Hower

The petrographic composition of sized coal produced through the progressive grinding of a Central Appalachian high-volatile bituminous coal blend was analyzed for multiple sets either by removing fine, -200-mesh, coal after each test iteration or by retaining the fine coal in progressive test fractions. With prolonged grinding, coarser fractions tend to become depleted in vitrinite and vitrinite-rich microl ithotypes, leading to progressively harder-to-grind coal remaining in the oversize, +200-mesh, fractions. The latter trend is shown both by the maceral and microlithotype composition of the coal and by the increased slope and fractal dimension of size frequency distribution, implying an increase in hardness and resistance to grinding of the oversize coal.

Jan 1, 2000

By George J. Bujtor, Anthony K. Scott, Haddon F. King

In 1982, the result of a 3-year study was published as "A Guide to the Understanding of Ore Reserve Estimation". The principal conclusions were that computation formed only part, and perhaps not the most important part, of an estimate and that the estimate should recognize that geological, mining engineering and metallurgical judgements formed an essential part of the eventual result. Subsequent expectation/realization studies of several mines have produced case histories which form the principal basis of the paper. These imply that geology is even a larger factor than thought earlier.

Jan 1, 1992

By J. S. Y. Wang, R. C. Trautz

To evaluate the potential for water seeping into an underground opening, a 9-m- (30-ft-) long drift was constructed in the unsaturated fractured tuff at Yucca Mountain. Forty seepage tests were performed by releasing finite volumes of water at a constant rate into short test intervals located in boreholes positioned above the drift. The seepage threshold flux, defined as the liquid-release flux at and below which water will not drip into the opening, was determined for 10 test intervals. The seepage data, observations and model results indicate that a seepage threshold exists because a capillary barrier diverts water around the opening.

Jan 1, 2002

By W. C. Patrick

Introduction The availability of a thorough, simple-to-use roof fall classification system is desirable for several reasons. First, such a system would expedite the reporting of falls for the purposes of estimating material removal costs, analyzing damage levels, and complying with federal regulations to report falls in certain areas of the mine. Second, the classification system would allow the mining engineer to record falls routinely with little time and effort expended. This would encourage him to make observations concerning what type of roof support would work best in a given situation. Third, and probably most important, an adequate roof fall classification system is the first step toward developing a means of predicting the occurrence and extent of future falls. It was with these three reasons in mind that the following classification system was developed. The type of classification chosen reflects the background of the developer and the intended purposes of the system. Hylbert has proposed a geologic-based classification which groups falls as to structural and compositional origin. The need for similar systems is noted by Cox and by Ferm and Melton. Each of these researchers is confronted with a situation requiring a relationship between local geology and roof fall occurrence. Such a relationship would allow the prediction of the relative frequency of falls from a knowledge of local geologic features. The current research is aimed at fulfilling somewhat different requirements, as noted above. Fall geometry has been chosen as the basis of the classification system so fall type can be reported independent of local geological, environmental, and tectonic conditions. This approach parallels that used in the common slope failure classification with groups failures relatively independent of

Jan 1, 1977

By J. M. Dean, R. L. Grayson, R. D. Begley, G. L. Winn

Evidence has accumulated indicating that cultural change toward safer workplace behaviors is beginning to occur systematically in the coal industry. Through a range of programmatic mining company successes, enforcement and litigative actions, economic responses to competition and integrated efforts by federal and state agencies, a broader participation of safety and training professionals is being achieved to address prioritized workplace problems at mines. Small steps in workplace-related improvements have been realized already, but the trends in industry safety statistics, coupled with focused programmatic initiatives, indicate that more definitive and systematic steps are occurring to improve safe behavior in the workplace routinely.

Jan 1, 1998

By Martin P. Corriveau

It is not news to anyone in the mining industry that federal action in the prevention and abatement of air pollution has seriously affected the industry both directly and indirectly. It is the purpose of this paper to review how the development of federal action is directly affecting the coal mining industry's number one customer, the fossil-fuel-fired steam generating power plants and, consequently, the industry itself indirectly. In essence, Public Law 84-159 of 1955 as amended by the Clean Air Act of 1963 and its revisions in 1967 and 1970 progressively tightened federal coordination and management of air pollution control programs throughout these United States. The Environ- mental Protection Agency (E.P.A.) set up to direct the programs was charged to establish National Air Quality Standards, Standards of Performance for New Stationary Sources, and National Emission Standards for Hazardous Air Pollutants.

Jan 1, 1973

By H. Zhu, A. G. Journel

Qualitative and interpretive information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging, and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system provides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data. A case study using a large reference database is presented; the indicator conditioned estimates have a smaller conditional bias and a smaller error variance than the ordinary kriging estimates. The results also showed that the indicator conditioned estimator is more efficient for selection in mining.

Jan 1, 1990

By J. M. Mutmansky

The objective of this study was to produce coal dusts for laboratory research that are similar to mine airborne dusts in chemical, mineral, and physical characteristics. In this investigation, dusts produced in laboratory comminution equipment were compared with continuous-miner-generated dust for similarity in physical characteristics. Mining-generated dust (MGD) and bulk coal samples were first collected from an underground mining operation. The bulk samples were then processed in the laboratory for size reduction in various comminution devices. These laboratory-generated dust (LGD) samples were subjected to size and microscopic analyses. Physical properties of the dust particles were studied on a scanning electron microscope (SEM). A numerical shape coordinate system (SCS) was also developed and applied to 300 particles from each sample. Statistical analysis was then performed on the collected data and characteristics of the MGD and LGD samples were compared.

Jan 1, 1995

By Lynn B. Hales, Randy Ynchausti, Jeffrey D. Mckay

Many consider rougher flotation control to be more of an art than a science. Some have even thought it impossible to make process control decisions and changes without human interaction. Controlling flotation bank pulp levels to maintain consistent pulling rates in the face of changing feed slurry flow rates, varying mineral types, and inconsistent reagent additions can be daunting. However, an advanced supervisory control strategy was installed on the plant floor to control an industrial rougher flotation circuit with little or no operator interaction. Plant staff monitored the flotation circuit under supervisory control and reported benefits of up to 4% improvement in copper recovery above that achieved with an older supervisory control strategy. To accomplish this work, a novel use of instrumentation to solve a flotation bank pulp level control problem was employed, a new implementation approach was used to correct some flaws in the older approach, and careful attention was paid to a few key process control principles. This paper discusses important aspects of these activities.

Jan 1, 2000

By Deepak Malhotra

The first step in the development of a gold deposit is the detailed mineralogical examination of the ore types, major and minor mineral constituents and their association. It is extremely difficult and expensive mineralogically to characterize the occurrence and association of gold with other minerals for low-grade refractory ores (less than 0.1 troy oz/t Au). Even if a mineralogist can identify a gold-associated particle or two, one wonders how representative they are of the deposit. What alterative does a metallurgist have for characterization of gold-bearing ores? Diagnostic leach procedures, consisting of a series of sequential leaches, can provide the metallurgist/mineralogist with reasonably good Indication of the deportation of gold in the various mineral matrices. This information con help the metallurgist concentrate on the most promising process options In the Initial stages of the project development process.

Jan 1, 1993

By A. M. Al Taweel, S. M. El Mofty, T. A. Hassan, M. R. Moharam, A. M. Ramadan

The axial mixing characteristics of a pilot-scale flotation column were investigated with the objective of identifying means to mitigate the extent of axial mixing that adversely affects its grade/recovery performance. A wide range of design and operating conditions was investigated and the experimental results, obtained using the dynamic response method, were analyzed using three axial mixing models. The dynamic response of the column can best be described using the axial dispersion model. The results obtained suggest that the value of the axial dispersion coefficient, EL. can be signi6cantly reduced by judicial selection of hydrodynamic conditions and/or the use of column inserts that suppress the onset of hydrodynamic instabilities inherent to the operation of conventional flotation columns. Up to 40% reduction in the value of EL was thus obtained by using spargers that produce more uniform bubble sizes, while up to 30% reductions were obtained by controlling the residual frother concentration.

Jan 1, 1995

By Joseph Moses Botbol

The disposition of world mineral resources is such that a vital need exists for both the most efficient development of existing resources and the rapid disclosure of as-yet undiscovered resources. The technological developments described in this report are directed primarily toward the acceleration and increased efficiency of mineral-resource exploration program. In the past decade the use of computers in the mineral industry has grown exponentially. Most computer applications in mineral exploration are designed to be implemented either before or after data collection. Few, if any, computer applications are designed to be used during the collection of data. One major reason for the lack of development of computer applications in this area is that comunications links do not exist between computing systems and the remote areas that host mineral-deposit exploration programs.

Jan 1, 1975

By K. Biswas, H. C. Lee, S. J. Jung

Ore passes are circular openings excavated in rock for in-mine gravity-transportation of ore. It is a very important component of the overall load-haul system of an underground mine. The function of an ore pass is two-fold: first, gravity-transportation of ore from the extraction level to the haulage level and second, the loading operation at the haulage level utilizing the gate assembly. In reality, like any other system component, an ore pass breaks down either due to a hang-up within the ore pass or due to a failure in the gate structure. The failure of the gate assembly may be attributed to a greater extent to the impact load as experienced by the components of a gate structure as a result of the direct impacts of the rock fragments and to a lesser extent to the static or 'dead weight' loads of the accumulated materials in the ore pass. This paper uses simulations in Working Model® as an aid to investigate the effect of both the impact and static loading on the gate assembly and on the inner-walls of the ore pass. The paper also investigates the impact of ore pass inclination and the presence or absence of dogleg on the static and impact loading of the same.

Jan 1, 2002

By Enrique Farjeat P.

Mexico City's growth has encourage development of underworks to meet drainage and transport requirements. Deep Drainage System has been constructed through a complex tunnel network, 108 km in total, varying from 30 to 12 m in depth and 6.24 or 4.00 m in diameter. Wide range of stability conditions presented in soils has forced the use of several tunnelling methods, going from the manual procedure by the use of pneumatic tools, to slurry shields, or open face shields, with the aid of or without compressed air. For transport, subway tunnels have been excavated in very compact silty sands, 9.15 and 9.51 m in diameter, with the use of open shields one of which was designed by Mexican engineers as a prototype machine. This paper tries to describe evolution of tunnelling methods used in Mexico City during last 20 years.

Jan 1, 1991