Search Documents

By R. V. Ramani, J. Qin

During the mining process, the in-situ material is broken into different size ranges, from very large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable dust is associated with health and safety of the miners. The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined. The amount of respirable dust airborne is on the average only 0.016% of the respirable dust generated. On the average, 61% of the total airborne dust measured is in the respirable size range. The amount of respirable airborne is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (=0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of the airborne propensity of respirable dusts in mine atmospheres.

Jan 1, 1989

By Ronald J. Doll

The selection and matching of the conveyor drive components (Figure 1) determine the initial cost, long term costs, and how well the drive performance is matched to a project's long term production goals. This paper will cover the specification criteria and considerations that should be included in a conveyor drive specification. It will also review the practical aspects of the specification's intent and the solicitation of alternatives.

Jan 1, 1998

By Jim Jonas

The Berkeley pit-lake was sampled during two seasons, fall 1997 and spring 1998, from the surface to the bottom. Various parameters were measured to determine what effect the seasons had on the water column. It was determined that a seasonal turnover did occur between the fall and the spring sampling; however, the depth of mixing due to turnover could not be established. Trends were observed which suggested that microbial activity was altering the iron speciation at depth, and subsequently masking the extent of mixing. Various trace metals were removed from the surface water by either co-precipitation with schwertmannite or adsorption.

Jan 1, 2000

By Paul J. A. Lever

The mine environment is dynamic and operating conditions change continually and are difficult to predict. New equipment, variable geological conditions, modified layouts, and different equipment operators make monitoring and control system difficult to apply without continual software maintenance. The paper reports on algorithms that were developed, encoded with Knowledge Craft Tools, and tested on underground coal mine data to adapt to the dynamic environment. The system receives data from sensors in near real time and then identifies patterns in the data. Using a set of mode features the data is automatically checked to determine the present operating mode. When the operating mode changes from the previous shifts, the system automatically learns the new mode characteristics and uses that mode context for further data analysis. The concepts presented in this paper are applicable to a wide variety of mining scenarios, not just underground coal mining.

Jan 1, 1992

By Y. Ye, J. D. Miller

Certain bituminous coals are known to contain appreciable quantities of natural fossil or subfossil resin. Such resinous coals are found in the western US, particularly the Wasatch Plateau coalfield of UT. Some of the seams in this field contain an average of 5% resin. This fossil resin has been recovered by gravity and/or flotation processes since 1929. Resin concentrates thus produced are of low quality and are usually refined by solvent extraction. The purified resins are of commercial importance in the adhesive, coating, rubber. and ink industries, etc. An improved flotation technique has been developed which involves ozone conditioning to selectively float resin from high-volatile bituminous coal. With this flotation process, a concentrate product which contains 95%

Jan 1, 1990

By R. H. Grau

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. The research has demonstrated that the ventilation of large-opening mines improves significantly by including ventilation requirements in the mine planning process and implementing some practical techniques during mining. Planning the location of long pillars to reduce the number of crosscuts between intake airways and return airways, positioning auxiliary fans in their proper locations, and establishing ventilation stoppings with minimal leakage all significantly improve the ventilation of large-opening mines. Mine operators that adopt these techniques in the mine ventilation plan will reduce mineworkers? exposure to airborne contaminants.

Jan 1, 2008

By Frank F. Aplan, Edward C. Dowling, Richard R. Klimpel

Several series of time-instantaneous samples were taken on a cell-by-cell basis in the flotation circuits of the Pinto Valley, AZ copper concentrator. These samples were used to calculate mass flow rates throughout the circuit using standard, deterministic metallurgical formulae and also a variety of more statistically oriented techniques. Because of the magnitude of the errors associated with the individual cell samples, the standard metallurgical formulae are not sufficient. Consequently, it is necessary to utilize some type of statistical technique capable of distributing the individual cell sample errors in such a way so as to provide a physically useful mass balance for the entire circuit. This paper explores the use of linear and least squares programming as one technique to providing credible mass balance calculations. For linear programming this was done by distributing the error using two different criteria involving specific linear programming formulations: least absolute sum minimization (which assumes an underlying double exponential distribution error structure) and minimax (which minimizes the maximum absolute deviation and assumes an underlying rectangular distribution error structure). These results were then compared to the more standard formulation of minimization of the sum of least squares which assumes an underlying normal distribution error structure. The least absolute sum approach was particularly attractive due to its simplicity of use and the ease in which repetitive calculations can be done with no user intervention.

Jan 1, 1990

By Amri Priambodo, Ian Leslie, Valérie Laflèche, Agustina Ratnaningrum, Robin Paine, Andrianus Sinaga, Willem de Beer

Freeport Indonesia consists of surface, civil and underground mining areas exposed to numerous geotechnical risks and hazards. PTFI uses various monitoring systems (Micro-Seismic, Firefly Light System, Mira Geoscience machine learning, etc.) to effectively manage these risks. The significant volumes of data from these sensors must be integrated into actionable information to provide the expected risk management. This occurs at the GeoEngineering Integrated Monitoring Centre (GIMC), a centralized department within the GeoEngineering Division, tasked with the responsibility to manage all geotechnical monitoring systems. The main hazard the GIMC is responsible for managing in real time is mine seismicity within the underground mining areas and the potential impacts on safe operations. Seismic system engineers achieve this objective through 24 hours a day and seven days a week operations of the GIMC, providing a centralized point of communication, alerts, evacuations and control during seismic events and emergencies. This paper will describe how the GIMC achieves its goal using reliable procedures and strategies based on detailed Triggered Action Response Plan (TARP), concise communications, novel technologies (FireFly Lighting System), and proven seismic re-entry programs to manage risk within the underground mining operations. The integration of geotechnical monitoring and reporting into a centralized group has improved the effectiveness and management of seismic risks and hazards at PT Freeport Indonesia (PTFI) mining operations.

Apr 26, 2022

By J. Patrick Powers

In tunneling through water-bearing formations, the expense of controlling the water can have a major impact on overall project cost. The author has seen the cost of an eight-foot, finished sewer tunnel rise from under $500 per foot to over $1,000 when a water problem, anticipated as modest, became severe. There is need for greater professionalism in the approach to groundwater control. The days of the forked stick should be behind us. The basic technology exists. Its application is not yet widespread. This paper discusses predrainage; that is, the lowering of water in advance of tunnel excavation. Both free air and compressed air tunnels are considered. Examples from recent tunnel projects are described. SPECIAL NATURE OF TUNNEL DEWATERING Tunneling is unlike other excavations below the water table in a number of significant ways. The tunnel excavation is always on the critical path; if production slows or stops, there is no other work for the heading crews, no other work to carry the cost of service crews and job overhead. The dewatering commitment must be made well in advance. Construction of wells, and pumping down take time. After the heading reaches a trouble area, time is not available

Jan 1, 1997

By D. Antonov

The physical and mechanical properties of coal play a important role in the planing and design of coal mines. However, due to the complexity conditions in situ and the influence of unknown factors, it is hard for people to evaluate the physical and mechanical properties of coal directly. In this research, uniaxial compressive stress was used to change the attribute of coal samples, and the ultrasonic measure technique was used to evaluate the physical and mechanical properties of coal. The results of laboratory test showed that there was a strong relation between uniaxial stress and velocity of ultrasonic wave. Sensitivity analysis with numerical simulation was used to define the relation between the physical-mechanical parameters of coal and ultrasonoc wave. With the dynamic analysis module of FLAC, three elastic and plastic models were built to model the coal samples. The modeling parameters were changed pro rata, and the correlation of coal and ultrasonic wave properties were summarized and presented. The result from this research will be base for further analysis of caving behavior of coal.

Jan 1, 2010

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a longwall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases, employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1987

By Ravi Shah, Augusto Lucarelli, Daniele Peila

"In mechanized tunneling the annular gap between the segmental lining and the surrounding soil caused by tunnel driving, must be backfilled almost instantaneously with an adequate grouting mortar. The objective of this research is to perform a fully three dimensional modeled parametric study using FLAC 3D and evaluate the effects of backfill grouting on the tunneling performance. The research focuses on comparisons between different injection materials and state-of-the-art Bi-Component grout and their effects on the settlements on the surface. The research consists of testing a regular situation of tunnel excavation using a shielded machine with face under pressure. The tunnel dimensions and the soil properties are selected as close as possible to the reality and based on Turin Metro case. 1 INTRODUCTION Excavation of tunnels in urban areas can induce ground movements, which have negative effects on existing structures. In such scenarios, shield tunneling has become a well-accepted construction method in various ground conditions. It is characterized by relatively complex interactions between the soil, the tunnel boring machine (TBM) itself, the tunnel lining and the tail void grout. The problem to control the settlement depends on the face pressure, ground properties and back filling procedure and material of the tail void. The face pressure acts against the front to guarantee the face stability. In case of EPB TBMs the stability of the tunnel face is ensured through the excavated soil itself, which is conditioned and is maintained in compressed state within the excavation chamber. When excavating with TBMs a tail void is created between ground and the lining (Fig.1) after the TBM excavation and ring assembly that must be backfilled instantaneously by injecting the backfill material through the TBM’s tail shield. The process is of primary importance as it reduces the surface settlements and creates an immediate link between the ground and lining, sealing against ground water and leakage, reducing the differential movements between segments and providing long-term stability. The most used backfilling materials are: Inert mixtures that do not contain cement instead sometimes they are replaced by fly ash or other substitutes. A typical design of an inert mortar consists of sand, fly ash, bentonite and water. Pea gravel, which is constituted of granular materials with grain size ranging from 8 to 12 mm. This mixture is highly recommended for tunnels being constructed in rock mass with little deformation rates.Cement mortar is composed of cement, water, aggregates and sometimes bentonite. Cement controls the principle mechanical property of the mix, which can reach high values of 15-20 MPa in 28 days. The aggregates contribute towards the shear strength and reduce the pumpablity of the mix (Thewes and Budach, 2009). The reduced active systems have a cement content of 50-100 kg/m3, whereas the active system the binder component derives full hydration with cement content of over 200 kg/m3 ."

Jan 1, 2016

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the US Bureau of Mines has developed a PC-based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1995

By Donald P. Richards, William M. Greenslade, Daniel E. Albers

INTRODUCTION The application of oil field technology to large diameter hole drilling is beginning to offer a cost effective alternative to conventional shaft sinking methods. The drilling of ventilation and small production shafts are, of course, not new. The major constraint to the drilling of large diameter production shafts has been the inability to drill holes large enough and straight enough to install and operate relatively high volume hoisting equipment. This paper discusses recent advancements in drilling technology as applied specifically to large diameter holes for use in the mining industry. The paper emphasizes the geotechnical and hydrologic considerations in assessing site conditions and their application to drilled shaft technology. The authors worked together on a recent feasibility study for a 6 m (20 ft.) diameter 975 m (3,200 ft.) drilled shaft in New Mexico. Their individual experience in drilling and geotechnical investigations related to shaft sinking is world wide. DRILLING TECHNOLOGY Large diameter hole drilling has been a natural evolvement of oil well rotary drilling techniques. Most problems that were encountered in the rotary drilling of large diameter holes have been

Jan 1, 1981

By E. R. Braer, C. J. Bise

The trend in underground room-and-pillar coal mining is to employ remote-controlled, continuous-mining machines and extended cuts to depths of 12 m (40 ft) or more. This system of coal extraction, adopted by more than 435 mines, can create additional worker safety hazards. To address the ground-control-related safety hazards, a combination of statistical analysis and numerical modeling was used. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the coal mine roof rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling was completed to predict roof displacements during extended-cut mining. This paper describes the results of these studies and their impacts on the safety of extended-cut mining.

Jan 1, 2000

By James M. Reichman

Waterjet assist of mechanical cutters has been demonstrated in a variety of laboratory studies as well as on field equipment. As this technique becomes more widely accepted, it will be necessary to develop methods of minimizing the horsepower and water requirements. In machines such as roadheaders, continuous miners, and longwall shearers, the use of waterjet assist can be optimized through the development of phasing valves. Phasing valves will allow only the cutters in contact with the rock to be assisted. Since only 30 - 40% of the cutters are in contact with the rock, the saving power is significant. Flow Industries has developed a phasing system for use on roadheading machines. This system allows the operator extensive control of the angle of assist as well as the quadrant being assisted. This system could be greatly simplified for production machines and adapted for use in continuous miners and longwall machines.

Jan 1, 1985

By M. K. McCarter

INTRODUCTION Mining activity and basic geometry of open pit mines represent major obstacles in geotechnical mapping. Mining creates a constantly changing topographic base which may require corresponding updates of field sheets before mapping can proceed. The rapid pace of mining operations may also threaten removal of important geologic and engineering features before adequate base maps and surveyed control can be established. Maintaining such control during the mapping process is yet another complication. In addition, basic geometry yields nearly vertical outcrops. Access required for direct observation and measurement, essential to conventional plane table or Brunton techniques, may be impossible on such surfaces. Also, nearly vertical surfaces appear fore- shortened in plan view. This reduction in area provides little room for recording geotechnical detail. The difficulties encountered in open pit mapping can be substantially reduced by utilizing a modified form of plane table photogrammetry. This technique employs photographs taken from the ground as the base upon which details are recorded. The information is later transferred to plan maps using the plane table principal of location by intersection (Davis and Foote, 1953). Any change in topography can be accommodated by simply taking additional photographs. Proper spatial representation in plan view can be determined later when updated maps and surveyed control are available. In addition, horizontal photographs from the ground portray vertical surfaces as they are normally viewed thus providing maximum area for recording details. Any detail which can be identified on the photograph can be located correctly even though the actual feature is physically inaccessible. The technique presented in this paper was developed by the author for special applications at Kennecott's Bingham operation in 1970. The procedure was rapidly adopted for general use and has proven to be a practical tool for detailed investigation of potentially unstable areas (Zavodni and McCarter, 1976) and routine geological mapping (Richardson, 1975). Major advantages, other than those mentioned above, include: The speed and accuracy are greater than for conventional plane table or Brunton methods. The photo- graph represents a view from a station at some distance from the area being mapped. This vantage point allows evaluation of possible continuity of structures from one level to another which may not be evident at close range. The photographic base provides a permanent record of the topography at the time

Jan 1, 1977

By J. DeYoung

Weak demand for metals and consequent low metal prices resulted in continuation of the depressed state of US mineral exploration activity through 1983. Data collected by Resources for the Future Inc. and The Pennsylvania State University for a cooperative study on mineral exploration activity indicate that US exploration in 1983 fell by as much as 25% from 1982 levels. Precious metals remained the focus of most exploration efforts, as gold and silver prices remained attractive compared to base metals. Reports of 1983 domestic exploration and development activities in several industry journals indicates that about 85% to 90% of those projects were directed primarily at gold and silver. Gold exploration included work by several companies on Carlin- type disseminated gold deposits in Nevada, geological prospecting and drilling in the Wenatchee Gold Belt in Washington, and interest in lode and placer gold properties in California, especially by several small Canadian firms. Precious metals exploration projects were also reported in Alaska, Arizona, Colorado, Montana, New Mexico, Oregon, South Dakota, and Utah. There was also tome precious metal exploration activity in the eastern US. Development continued at the Ropes gold mine near Ishpeming, MI, and companies explored historic gold-producing areas in the Southeast. Some exploration for nonprecious metals took place last year. Stratabound copper-silver deposits were examined in western Montana, and US Borax continued exploring molybdenum resources in the Misty Fjords area in Alaska. Work on these projects during 1983 may have been stimulated by time limits on the availability of certain federal lands for exploration more than by projected improvements in metal markets. During 1983, several papers were published on mineral exploration strategies and the future of US exploration. David Watson of Raymond Kaiser Engineers, in a paper presented at the 1983 AMC Mining Convention, forecast increased exploration activity for gold and silver because of world economic conditions. He added that antimony, manganese, chromium, graphite, mercury, tantalum, tin, and barite are also likely targets based on their limited domestic reserve availability. He cited concern over reported subsidized mineral production by foreign producers and US regulatory and land-planning policies as retarding mineral exploration activity. Douglas Cook of Freeport Exploration Co., at the same meeting, presented a paper that showed that a 1950-75 period of vigorous exploration has been followed by a period where acquisition has replaced exploration as the predominant means of acquiring new mineral properties. At a December IIASA conference on "The Economics of Mineral Exploration," in Vienna, Austria, A. Rose and R. Eggert of The Pennsylvania State University pointed out that recent exploration decisions tend to rely more on evaluating production costs and comparing them with existing deposits, rather than on return of

Jan 5, 1984

By Daniel McConvey

Who is the Investor? -Mainly institutional, including resource funds, other mutual funds and pension funds. -Some hedge funds. -Retail investors. -How important is the reserve disclosure to these investors? -Do these investors know the difference between a reserve and a resource?

Jan 1, 2003

By Ishwar G. Mulani

In conveyor design, the first step is capacity and the second step is belt width and speed. The third step is decision on 'ff," where distinction arises between DIN/ISO and CEMA for calculating resistances. Then again, both the methods are virtually similar. This topic helps in understanding Dm design style and its comparison to CEMA. This topic is from the book Engineering Science and Application Design for Belt Conveyor wherein the issue has been analysed in detail. It presents a workable calculation model to calculate the value off in design office, based on conveyor parameters. CEMA uses Kx, Ky and 0.01 5 instead off. Thus, f is a sum effect of Kx, Ky and 0.015. Hence, knowledge on f is also applicable to Kx and Ky. This helps to understand their relationship.

Jan 1, 2004