Search Documents

By T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground-water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is obviously a more realistic simulation of the problem, but the former method is significantly easier to use, Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.15 to 0.60. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1992

By N. Damiano, J. Noll, C. Zhou, J. DuCarme

"Preventing machine-related injuries is one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable were characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which cause little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects. INTRODUCTION An average of 250 injuries occur every year during operation of Continuous mining machines (CMMs), and 43 miners have been killed by striking or pinning accidents involving CMMs in the U.S. from 1984 to 2015 (Mine Safety and Health Administration, 2015). In addition, there have been 10 fatal accidents involving mobile haulage equipped with trailing cables from 2000 to 2015 (Noll et al., 2017). In response to these fatalities and injuries the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 requiring the use of a proximity detection system (PDS) on all CMMs except full-face machines and proposed a regulation in 2016 which would require a PDS on other mobile underground equipment. Current PDSs approved for underground use are magnetic-field based. The PDS contains machine-mounted magnetic field generators that create fields around the machine. The other part of the PDS is a miner-wearable component (MWC) that reads the flux density of the generators. These systems use the magnetic field strength readings from the MWC to determine whether a miner is at a safe distance from the machine. A stable magnetic field is essential for the accuracy of the system."

Jan 1, 2018

By Panlop Huttagosol

The use of computer models to design ultimate pit limit of an open pit mine during its feasibility study has become an emphasized procedure in mining. It is a normal practice in open pit mine design to generate the most profitable final pit limit. The limitations of designing this optimal pit limit have been the requirement of significant computing efforts as well as the use of complicated operations research techniques. In an attempt to describe a computer method that has an easy conceptualization and is able to provide a precise and desirable solution, a new technique is developed. The ultimate pit limit problem is formulated as a large scale transportation problem. The formulation is based on the use of a three dimensional block model to represent an ore body and surrounding materials. The solution technique is developed through solving the dual system of the formulated problem by using the adapted simplex algorithm of linear programming. The implementation on given case studies demonstrates that the new method is capable of providing an optimum pit value. The computing effort required by the algorithm is still the main constraint in solving a large scale problem. The technique provides open pit mine planners with an alternative tool in using a commercial linear programming software which is capable of solving a general transportation problem. The selected software must be able to handle a large scale problem, and it needs an additional effort td formulate the problem and transform a result into the ultimate pit limit solution.

Jan 1, 1992

By S. Davis

It has been accepted almost as dogma that sampling contributes most of the error to fluctuations in gold fire assays. Differences in assay results on pulp material from the same sample interval are frequently regarded as evidence of the presence of the so called "nugget effect" or relatively coarse gold particles. It is true that if coarse gold particles are present they contribute to substantial sampling fluctuations, but while the process of sampling is probably the major source, the analytical process cannot -be completely ignored as a possible contributor to erratic assay results. In order to maintain a stable assay process, the analytic part of the system must be kept in control as well as the sampling and preparation part. One way of monitoring the performance of the analytic system is to systematically assay standard material whose sampling characteristics are carefully controlled. Gold assay standards are not prepared nor can they be prepared to account for both sampling and analytical errors. It is not possible to send coarse material to a lab for preparation (which includes both the processes of comminution and splitting) followed by fire assay, to make inferences only about the fire assay process. Because most gold ores are very heterogeneous, sampling errors would in most cases completely mask the contribution of the analytical errors. Assay standard material is prepared only to assess the accuracy and variability in the fire assay process.

Jan 1, 1995

By Erik A. Munroe, Nelia W. Dunbar, Virginia T. McLemore

In New Mexico, there are at least 100,000 abandoned mine waste rock piles with widely ranging geochemical and mineralogical compositions. A geochemical and mineralogical study was implemented for five waste rock piles, some which contained sulfides, in the Hillsborn Mining District. Chemical and physical characteristics of mineral grains and their secondary mineral oxidation rinds were examined with the electron microprobe. Pyrite and chalcopyrite appear to be the most reactive to oxidizing conditions. Clays, iron oxide, iron hydroxide, iron sulfate, and primary texture rinds exist in the waste rock piles analyzed.

Jan 1, 2000

By Oren Tranbarger

The ability to sense or detect the coal/non-coal interface during mining can provide numerous advantages for improving net coal recovery and quality, for increasing productivity, and for mining coal which would otherwise be ignored. This is particularly true when considering multiple, pitching, and thin coal seams. This paper discusses the application of coal interface sensing and examines several potential coal interface sensing techniques with respect to state-of- the-art, design, performance, and cost criteria. Four interface boundaries are considered: the roof, the floor, the rib, and the forward region.

Jan 1, 1982

By William Laird

In the process of mining coal today, our greatest asset, the coal miner, is faced with the indirect and direct consequence of underground mining operations. The indirect considerations may be the rank of the coal seam, the amount of overburden, geological factors, seam permeability and cracks. The introduction of newer, bigger and faster coal-producing face equipment having the capability to cut or rip through the bedding planes, cleats and micropores of the coal seam brings about rapid liberation of gas accompanied by greater concentrations of coal dust, has exerted a direct consideration and greater demand upon mine ventilation systems and dust control. The purpose of mine ventilation is to provide sufficient pure air to the miners working underground and to dilute, render harmless, and carry away all the dangerous and noxious gases. The mining operations which create coal dust are cod cutting, drilling, blasting, loading, hauling, dumping and movement of face equipment. The created fine dust causes the propagation of explosions. When quantities of coal dust with no methane present are raked in a sufficiently dense cloud in the presence of a source of ignition, an explosion is possible.

Jan 1, 1980

By D. H. Davidson

The basic principal in the ISL process involves the recovery of metal values by moving fluids through rock instead of moving rock. The process combines surface and sub-surface operations, with the economic performance controlled by four major factors; rates of fluid injection and production from wells; the rate of mineral solubilization; the volume of rock swept by the fluid; and the volume of solution processed through the system. This paper discusses various technical and economic parameters affecting these four factors and how they impact project costs.

Jan 1, 1985

By Andy B. Wallace

Veins in the Pyramid district of northwestern Nevada occur along steep fractures in Oligocene and Miocene quartz latite tuffs. The vein mineralization is zoned from a central enargite-pyrite zone outward through a complex polymetallic intermediate zone and an outer zone of galena and pyrite. Wall rock alteration includes advanced argillic and sericitic envelopes along veins superimposed on district-wide propylitization. The ore distribution and alteration patterns were probably produced by an increase in pH, a decrease in sulfur fugacity, along with cooling of the migrating hydrothermal fluid.

Jan 1, 1978

By Andreas Eberhorn

The evaluation criteria for cost comparison of the Gearless Drive, also called Ringmotor or wrap-around motor, as variable-speed drive with a Twin Drive System using synchronous motors are reviewed. Both mechanical and electrical components of the drive system are considered. The evaluation criteria are described and for the cost comparison the applicable method is demonstrated. The cost comparison is based on a medium and large sized mill system. Each drive package will display cost details with regard to capital cost, maintenance, power losses, overall efficiency, overhead and loss of production. As conclusion the benefits and disadvantages of the two drive/mill packages will be presented together with a payback diagram.

Jan 1, 1996

By R. D. Irvine

Enhanced concern for protection of the environment and attendant actions by environmental regulatory authorities in support of this concern are influencing to varying degrees the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms. In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States.

Jan 1, 1995

By Jamal Rostami, Jürgen Schmitt, Rohola Hasanpour

"Double Shield TBMs can be used in fast track projects for accelerated completion where there is limited information available on ground conditions and there are possibilities of encountering weak ground and shear zones. As such, the shielded TBMs are the primary choice of the machines in long tunnels, but face the possibility of entrapment in squeezing ground, which entails long delays and major risks. This paper examines the possibility of using ground improvement methods to increase ground strength, and thus, increase the capability of the machines to cope with squeezing ground conditions. In this study, 3D finite difference simulation of a shielded TBM in squeezing ground was performed to estimate the operational parameters including required thrust to get a machine out of an entrapment. This analysis was also used to evaluate the possibility of preventing machine jamming by the implementation of pre-excavation ground improvement to increase the strength of the ground. INTRODUCTION In order to face adverse tunneling conditions especially using a shielded TBM in squeezing ground, new shield designs, with extra thrust and torque, step shield geometry with reduced shield diameter from front to the back, and conical shape shields have been used. In addition, many of the new machines have the capability to implement ground improvement at distances up to 50 m ahead of the face in order to reinforce the ground and further increase in their chances to cope with squeezing ground conditions. While these features have been added to the machine, there has not been a thorough evaluation of their impact on improving the chances to avoid machine jamming in weak rocks at high depth, which is conducive to rapid convergence of the ground."

Jan 1, 2016

By G. M. L. Robinson

Mineral Processing Wastes, as defined by the Environmental Protection Agency (EPA), has determined that most of the mine wastes will be regulated pursuant to subtitle D (Solid Waste Regulations) of the Solid Waste Disposal Act while specific mine waste categories will be regulated within the framework of the Toxic Substance Control Act. Though EPA's determination currently relieves the industry of the regulatory constraints mandated by the Resource Conservation and Recovery Act (Hazardous Waste Regulations) Subtitle C regulatory framework; the industry is not granted immunity from historical or current environmental regulations related to listed or characteristically hazardous or solid wastes. Because of the current regulatory trends and the need to implement cost effective remediation alternatives; advanced currently available on-site remediation technologies are available to minimize, reduce, contain or prevent environmental impacts related to mining and processing activities. In light of industry technical needs, an overview of the research and commercially available remediation technologies will be discussed and a brief discussion of the strengths and weakness of each technology will be presented. Technologies to be discussed includes stabilization, solidification, soil wash, soil flush, thermal distillation, pump and treat, metal extraction, centrifuges, filter presses, bioremediation, and incineration.

Jan 1, 1992

By Lawrence A. Roe

This paper describes research and development efforts leading to a wet process for the beneficiation of Western talc ores in which the values are primarily present as soft, platy talc mineral. The mineralogy of the ore, as it relates to the logic of utilizing an uncomplicated, attrition-scrubbing sedimentation process is described. Bench-scale laboratory testwork and a pilot-plant test program are described. The pilot-plant program included production of several tons of products. The thickened talc slurries were very difficult to dewater prior to the drying step. Dewatering difficulties were overcome by use of a high-speed centrifuge. The centrifuge cake was dried either by tray, flash or spray drying. The successful use of one high-grade talc product as titanium dioxide extender in paper is discussed. The talc product has extremely low abrasion values, an important characteristic for minerals used in paper manufacture. It is concluded that this wet process for soft talc ores is capable of producing high-purity talc products for paint, paper, cosmetics and other industrial uses re-quiring very pure soft talc.

Jan 1, 1972

By Gary Bennethum, L. Courtland Lee

INTRODUCTION For any identified mineral resource to qualify as a minable reserve, it must contain legally and economically extractable mineral at the time of determination. As competition for land has increased, the legal complexities have more than kept pace, frequently becoming the most important determinant in mineral exploration and development projects. Rarely will developers of a project avoid having to obtain numerous federal, state, and/or local permits while acquiring the necessary legal permission to begin mining. Each site must be selected carefully, not only for economic feasibility, but also for legal feasibility. Although it is impossible to present site-specific solutions for all potential underground developments, certain generalizations may be applied to specific land categories, particularly federally owned land. Such federally owned land includes more than 33% of the land area of the United States and many of the areas potentially attractive for future development. State and local restrictions affect a large portion of the nonfederal land, and those restrictions are equally important even though their diversity and current status require more regional study than can be provided herein (the list of references include sources of additional information). Each potential mining site requires a title search of the land status to determine the land ownership and the conditions affecting development. In addition, appropriate data concerning the mineralogic and economic potentials of an area must be collected. As listed in Table 1, many sources of public information are avail- able to aid potential developers. Fig. 1 illustrates a typical federal master title plat. HISTORICAL PERSPECTIVE The settlement of the United States reflects a fascinating history of public-land laws and subsequent mineral-disposal laws. Most of the statutes of the eighteenth and nineteenth centuries sought to dispose of land for the purpose of generating revenue to the federal government. The underlying need for general revenue contributed directly to numerous and often conflicting land policies. More recently, diverse federal programs such as environmental legislation have transcended the need for revenue in forming the framework that determines who has power over mineral developments and where those developments can take place. In 1812, the General Land Office was established under the Treasury Dept. At that time, English common law prevailed, entitling the owner of the surface to whatever was contained within the surface boundaries from the surface to the center of the earth. Unless a distinct title separated the mineral estate, it was included in the surface-land ownership. However, gold and silver were the property of the crown and were controlled by sovereign prerogative. Early state legislation on the subject of mines and minerals may be classified as legislation providing for the sale of state lands with a reservation of the minerals and legislation recognizing or asserting the sovereign prerogative for precious metals. In 1781, a Pennsylvania statute reserved 20% of all gold and silver ore for the use of the commonwealth. Thomas Jefferson suggested that a portion of all gold and silver be retained by the federal government. These early rules affecting land in the eastern states, now privately held, have been re- pealed, declared obsolete, or largely ignored. Federal legislation prior to 1848 and affecting mining may be classified as legislation reserving the minerals to the United States and legislation authorizing the disposition of reserved minerals by sale, lease, or grant. With many modifications, these basic policies remain in effect at the present time. A 1796 act provided for the sale of the Northwest Territory and for the establishment of the present system of rectangular survey for public lands. The Lake Superior copper region was the scene of "wild and baseless excitement in 1837" when the attorney general concluded that the president had the power to lease lands in Wisconsin; this opinion soon was overturned by another attorney general. By 1846, Congress had passed legislation authorizing the president to sell reserved lead mines "as soon as practicable" since the system of granting Leases had proved to be unprofitable to both the government and the lessees, many of whom refused to pay the rent. The general practice of early federal Legislation was to make a distinction between mineral lands and other lands, deal with them separately, and generally withhold mineral lands from disposal except through special legislation dealing with particular land. In 1848, following the treaty of Guadalupe Hidalgo, a vast land area was ceded to the United States by Mexico. This area included the present states of California, Nevada, and Utah, as well as portions of Arizona. Colorado, New Mexico, and Wyoming. This abolished the Mexican laws and customs relating to mining and preceded the adoption of the miners' own rules and customs. The adoption of those rules and customs followed a hard-fought battle between western congressmen and the eastern establishment. The western congressmen advocated adopting local customs through a location patent system, while the eastern establishment, particularly in Ohio and Indiana, favored an all- leasing system to pay off Civil War debts. The first mining law was passed in 1869 as an amendment to an act granting right-of-way to ditch land owners, and it was followed by the 1872 Mining Law. Precedent was established for the first categories of protected lands in the opening words of this act, which included the phrase "all unreserved" lands. Reserved lands subsequently defined included military and Indian reservations and were excluded from location since they were determined to be reserved lands. However, the overriding purpose of the mining laws was to settle the western lands and generate revenues for the federal

Jan 1, 1982

By V. H. Forsythe

Mr. Chairman, members of SME, and guests It is indeed a pleasure to have the opportunity to appear before this group. The topic of this paper is, "Current Trends in Related Industries and Their Influence on Electric Shovel Design and Size". Before getting into the major items, it is well to point out that this text will deal with loading shovels primarily, since their application is almost universal in major open pit mining operations throughout the world. Related industries influence our design in many ways. For the sake of simplicity, these industries will be broken down into two major categories. The first category to be discussed will include industries that will indirectly influence design and size, while the second category will include industries whose products can directly be incorporated by the engineer in the design of shovels.

Jan 1, 1964

By A. G. Naguib

In essence, any magnetic separator operates on the basis of imparting a preferential magnetic force on particles of higher magnetic susceptibility which are to be separated from particles of lower magnetic susceptibility. A certain amount of directional deviation to the particles takes place thus allowing for collecting each category of particles separately. The forces in action on particles in a wet magnetic separator of the established designs can be analyzed in a simple manner as shown in Figure 1.

Jan 1, 1972

By Frank Palkovits

All technologies move through a cycle from infancy to maturity. Thickened tailings have moved into the young adulthood phase of its development. Many mining companies like the idea of reducing their water-taking and water disposal issues. This limits the risks associated with traditional surface water-covered tailings facilities and the reduced dilution possible through underground disposal of thickened or paste tailings. Just as home theater systems advertised as ?plug and play? are rarely quite that straightforward, implementing and improving a thickened-tailings system has its challenges. However, the technology has also developed in recent years so it is more accessible. Some success factors have emerged because of the new technologies. Is thickened tailings the right solution? The first step in success with thickened tailings should be whether it is, in fact, the right solution for a particular mine. And, if so, what type of thickening is best. The answer depends on several factors, including: ? Grain size: The grain size that is optimal for maximizing mill recovery is some-times not suitable for thickening. Other mineralogical factors, such as mica content, may also influence whether the tailings are suitable. ? Water issues: Available water does not always have the purity necessary for the process. Another issue to consider is that if water is in short supply, as is increasingly often the case, thickening may be a way to reduce the need to both take and dispose of water.

Jan 1, 2008

By Harold D. Palmer

The marine geologist and coastal engineer have at their disposal a wide variety of geophysical tools with which to investi¬gate sea floor topography and structure. Such devices include towed magnetometers, shipboard gravimeters and a variety of acoustical systems for recording the relief of the sea floor and buried structural features. The versatility of this latter group of systems lends itself to a variety of applications essential to those projects where excava¬tion of the sea floor is required. This paper describes the use of several acoustic devices and their Limitations and presents a case history in which a rapid survey from a small vessel provided detailed information critical to the planning stage of a specific coastal project. In this discussion, shallow water is defined as depths less than 150 feet. At present, this limit includes the maximum depth of economic dredging and most other offshore activities. To be sure, the maximum depth at which routine useful work can be accomplished is rapidly increasing, but the majority of current marine activities are located in water depths here defined as shallow.

Jan 1, 1968

By N. Rowlands

The importance of mineralogical and chemical characterization of fine particles in the fields of mineral and metallurgical processing is discussed. Emphasis is placed on electron beam analysis techniques including electron diffraction and energy dispersive analysis with special reference to the scanning trans- mission electron microscope. The correct choice of instrument depending upon particle size, composition and nature of sample is stressed and the analytica1 capabilities of different types of instruments are evaluated. Recent applications of electron beam equipment to processing problems are presented and the paper concludes with a review of new developments in the fields of surface analysis and micro-diffraction.

Jan 1, 1985