Search Documents

By B. van Beek, J. H. Zietsman, A. Lexmond, N. J. Andrew

"In platinum group metals (PGMs) smelting, the slag-to-matte ratios are very high (approximately 4:1 to 9:1). The slag temperature therefore has a strong influence on matte temperature, which is a continual concern due to the low matte melting temperature and its resultant high superheat. Maintaining a stable slag temperature is therefore a critical safety and operational issue. This project aims to improve the understanding of the slag bath temperature drivers so that a more effective slag bath temperature control strategy can be implemented.With the aim of developing a multiphysics model of the furnace, extensive data analysis was performed to develop an in-depth understanding of the process before the start of modelling work. In this work, the effect of fluctuating furnace feed composition on slag temperature was examined. The results are based on equilibrium calculations using FactSage, implemented with ChemApp.A method was developed, using an equilibrium calculation at 25°C, to convert the available chemical assays to approximate mineralogical assays in order to determine the feed enthalpies. Actual 2013 furnace feed data was used and the average specific energy requirement to produce slag and matte at 1600°C was calculated to be 671 kWh/t concentrate. The furnace energy input was then kept constant, and it was found that the slag temperature varies significantly as a function of the feed composition. These results were compared to actual slag temperatures measured on site. It was found that close management of the furnace energy balance is important for maintaining a stable slag temperature."

Jan 1, 2014

By D. Wines

"Slope stability analyses have traditionally been undertaken in two dimensions assuming plane strain conditions. Although three-dimensional analysis techniques are widely available and used routinely for open pits, two-dimensional analyses are still more common due to the relative ease of model construction and the relatively rapid simulation times.Two-dimensional analyses will often produce different results to three-dimensional analyses for the same slope. It is generally thought that two-dimensional analyses will produce more conservative results. The main reason for the differences is the ability of three-dimensional analyses to account for the three-dimensional nature of the various model inputs, including the slope geometry, the distribution of soil and rock mass domains, the orientation of geological structures with respect to the excavation face, the orientation of the in situ stresses, and the distribution of pore pressure. In some cases, for a long, straight slope in basic geological conditions, two-dimensional analyses can provide a reasonable representation of the problem. However, in many cases, the inability of a two-dimensional analysis to represent the true three-dimensional nature of the problem will lead to unrealistic analysis results.This paper discusses the reasons, as detailed above, for the differences in two-dimensional and three-dimensional analysis results. Work by others is summarized, and additional numerical analyses are performed to provide an improved understanding of the effects of slope geometry, structural orientations, and in situ stresses on predicted stability. Case studies are presented for both stable and unstable slopes, and the behaviour of these slopes is related to the three-dimensional nature of the slope geometry and geology.The previous work, the new analyses performed here, and the case studies show that it is often important to provide a realistic representation of the slope in three dimensions in order to obtain reasonable stability analysis results. This is particularly true for hard rock environments where structurally controlled failure mechanisms are most likely. The paper also highlights the fact that back-analysed properties obtained from one analysis technique are not necessarily applicable to forward analyses using another technique."

Jan 1, 2016

By C G. Robinson, B. K. Loveday, J. C. Paynter

"A method of optimizing the design of a processing plant has been developed which minimizes capital and operating costs for average stripping ratios and ore characteristics. Models were developed to describe the operating characteristics and costs involved in various operations such as up-grading, leaching and solid-liquid separation.The options available in up-grading policy and the relation between the cut-off grade and the costs incurred subsequently in the treatment of the ore formed the basis of the optimization. To arrive at an optimum plant configuration and a set of operating parameters, the interrelation between grinding size, leaching temperature, leaching time, and various plant recycle options was investigated."

Jan 1, 2014

By C. Kelley

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings as fine as 75 microns and coarser have been used. In dry screening operations these same urethane screen surfaces have been relegated to only the coarser separation ranging from 1.0 mm and larger. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies, which allow an end user to consider urethane screen surfaces for dry screening operations where separations as fine as 75 microns are required. These technologies allow an end user to realize the inherent advantages of urethane in wear resistance while also realizing the benefits that a high open area urethane screen surface can bring. These benefits include non-blinding characteristics and feed capacities, which rival that of traditional stainless-steel woven wire mesh screen surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines in conjunction with which they are used. There will also be a presentation of several case studies of commercial installations where these technologies are utilized. These case studies are from the mineral sands industry; therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints, which must be taken into account when considering urethane screen surfaces such as temperature and chemical attack. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By K. Cole, D. Mesa, P. Brito-Parada, M. R. van Heerden

Turbulence in mechanical flotation cells, achieved via an impeller, plays a key role in keeping particles in suspension, dispersing air bubbles, and promoting particle-bubble collision. However, studying the hydrodynamics of a flotation cell is not a simple task, due to the complex nature of flotation systems which are opaque, turbulent, multiphase and polydisperse in terms of particle and bubble sizes. In this paper we study the impact of impeller design modifications on the hydrodynamics of a continuously overflowing bench-scale flotation tank. To this end, two different impeller designs, with and without a stator, were assessed using Positron Emission Particle Tracking (PEPT). This allowed the authors to determine, for the first time, the effect of an impeller design on the behaviour of both hydrophobic and hydrophilic particle tracers. It was experimentally observed that the use of a stator modifies the hydrodynamics within the flotation cell, distorting the lower mixing loop that is characteristic of axial impellers. The role of the stator in dissipating turbulence results in reduced particle velocities outside of the impeller-stator region. These results have important implications for flotation cell design and are discussed in the context of the impact that different designs have on particle movement, flotation hydrodynamics and, ultimately, flotation performance. The data set generated is also extremely valuable for modelling and validation purposes. Keywords: Flotation, flotation tank, impeller design, rotor, stator, PEPT, hydrodynamics

Jan 1, 2020

By G. Drennan, A. Cameron

"South African mining operations depend on the skilled professionals produced through the tertiary education sector. In geoscience courses at the University of the Witwatersrand, which lead into the mining sector, there has been a significant increase in student intake over the past 15 years. This increase has been characterized by a radical shift in demography: in classes where white male students once formed the majority, black female students are now in the majority. This demographic shift appears closely linked to policies addressing issues of social justice and transformation in post-apartheid South Africa. We document this change and consider the role played by employment equity legislation (as in the Mining Charter) and corporate social investment strategies in the mining industry, notably through bursaries offered to black female students. We also look at the changing needs of the industry, where the critical need for managerial skills, not just technical knowledge, is highlighted through data from surveys of past students and industry managers. Our findings indicate the need for a curriculum adjustment to meet these changing requirements, as well as more rigorous selection criteria for bursars than simply gender, race, and appropriate matric results. IntroductionThe South African economy has historically been linked to mining and the exploitation of mineral resources. South African mining operations are dependent on the professional labour that is produced through the tertiary education sector, with critical thinking, teamwork, and the art of negotiation having been identified as the crucial skills required for this industry (Sideropoulos, 2014). Over the past three decades the South African system of education has gone through a period of dysfunction that it is struggling to rectify (Maphai, 2014). This has impacted on the levels of academic preparedness of students applying for places in higher education. Concurrently, government and university policies have widened access to higher education in response to the need to address issues of social injustice and transformation related to South Africa’s history of apartheid. As a result, the number of students admitted to universities has increased dramatically. In the School of Geosciences at the University of the Witwatersrand (Wits), the increase in student numbers has been accompanied by a significant change in demographics: classrooms which in the past were dominated by white males have given way to classrooms in which black females are often in the majority. This demographic shift is related to legislation such as the Mineral and Petroleum Resources Development Act and the Broadbased Socio-Economic Empowerment Charter, developed to reshape the socio-economic and equity frameworks of the country (Botha and Cronje, 2015). Requirements aimed at transformation in terms of management, skills development, and employment equity, together with corporate social investment (CSI) requirements, have resulted in bursaries being made available to attract students from designated groups, which in turn has increased the number of black students, and notably black female students, taking courses in geosciences. However, due to the economic downturn, instability in the mining industry has recently resulted in the downsizing of some mines, with international investors pulling out of South Africa. This instability resulted in devastating strikes across all sectors of the mining industry (Stewart, 2013) and in Marikana, an important platinum mining area, the strike culminated in a deadly shoot-out between miners and police. The resulting tensions spilled over into the gold mining sector, resulting in further strike action, shaft closures, and retrenchments. These challenges have implications not only for the mining industry in South Africa, but for the tertiary education providers whose graduates would have been absorbed into the mine-related workforce."

Jan 1, 2017

By A. Ndibalema

Blasting is one of the primary functions in any mining operation. Despite the fact that it generally constitutes between 30% to 40% of the mining cost, blasting also affects the cost-effectiveness of down steam activities such as load and haul, safety, tyre life for haul trucks, crushing and milling. Over the past three decades, significant progress has been made in the development of new technology in an attempt to reduce costs and increase efficiencies and productivities of blasting activities. Mine to mill project concepts have paved the way for such developments. Other advancements have included sophisticated computer modelling technologies for blast design and performance analysis. There are many factors that affect the cost of blasting. These can be divided into two categories; controllable and uncontrollable. The latter includes costs related to depreciation, exchange rates and government legislation with the former category including contractor versus owner blasting costs, efficiency and productivity issues and product quality. Controllable factors have one common denominator which can determine their outcome; direct site management influence. Excavator digging rates and final floor conditions give a good measure of blasting performance, and alternatively cost effectiveness. This paper is aimed at benchmarking against a blast optimisation database, understanding the relationship between costs and identifying opportunities for improvement. Understanding the cost drivers allowed a typical cost model to be developed for the current mining operation at Geita and this was used to drive continuous improvement with emphasis on closing the information loop.

Jan 1, 2008

By John Taylor

?Introduction to Black Mountain ?Historical metal accounting practice ?Metal accounting audit ?Feed measurement ?Sample precision ?Concentrate measurment ?Current metal accounting practice ?Further refinements to the metal accounting practice

Jan 1, 2005

By P. T. Slatter

The role of viscometers for rheological characterization in the hydraulic transport of solids is discussed, and rheological models and phenomena pertinent to the hydraulic transport of backfill material are reviewed. The two main branches of viscometry (rotational and tube) for the measurement of mining slimes rheology are compared. The effects of solids concentration, particle size and chemical additives and the practical application of rheology in backfill system design are presented.

Jan 1, 1988

By A. Montini

The problems encountered in the design of control systems for milling cir- cuits when the model of the system and the model parameters are uncertain are discussed. Considering these uncertainty factors has led to the development of a technique that gives a quantitative assessment of real system stability, reveals the trade-offs between performance and stability and helps the designer in deciding what level of model complexity to use in the controller design. Furthermore, it allows for on- or off-line optimization of the milling circuit performance as it provides the base for the design of a controller which is stable over the plant operating range.

Jan 1, 1987

By J. H. Zietsman, W. J. Leipoldt

"To be able to responsibly develop a multiphysics model of the steel belt sintering (SBS) process used to sinter chromite fines, it is important to have a comprehensive understanding of the process. This understanding was gained through a site visit, observation of the process in operation, and interaction with the operators. Material characterization will also reveal much about the process that is not yet fully understood. A well-defined and representative mass and energy balance will also give valuable insight into the process. The plan for the multiphysics model aims to combine a computational fluid dynamics (CFD) model with a discrete element method (DEM) model.To obtain a more accurate mass and energy balance representation of the SBS process, it was decided to develop a dynamic distributed parameter model of the mass and energy balance. This model will be used to gain better understanding of the SBS process so that a more complicated multiphysics model can be developed later. The reason for this is because the SBS process is very dynamic, with a large temperature distribution throughout the length of the process. In its current state, the mass and energy balance model is capable of handling solid and gas material packages and exchanging heat between these packages where they are mixed, and is able to model the heating of the gas by burning CO gas. The next step in the development of the model will involve enabling it to handle evaporatoin of liquid water, burning of solid carbon in the pellets, reduction of iron oxide in the pellets with the CO gas formed from carbon combustion, and then oxidation of the reduced iron in the oxygen-rich cooling zones."

Jan 1, 2014

By M. D. Raganya

The Kriel Colliery is an Anglo Coal mine which is contracted with Eskom to produce No. 4 seam for Kriel power station. The mine previously found it uneconomical to mine No. 5 seam due to the low qualities and tonnages of the seam, both at the opencast and underground sections. An area has been encountered for the first time at Kriel Colliery opencast pit 5, where the tonnage and qualities of No. 5 seam warrant further investigation. The primary reason for the investi¬gation of No. 5 seam by Kriel Colliery is because of the advantage of the high selling price (R450/t) that the market is currently prepared to pay for the No. 5 seam. The aim of this project is to mine No. 5 seam economically without interrupting No. 4 seam mining operations. The problem is that the equipments that are currently being used at the mine belong to Eskom and are dedicated to mining No. 4 seam only, not No. 5 seam. Through geology investigation, it is found that the whole No. 5 seam (No. 5 seam upper and lower) has an average thickness of 1.8 m. It also contains a parting of carbonaceous shale which divides the seam into two parts. No. 5 seam upper contains less tonnage compared to No. 5 seam lower. The calorific value and ash content of No. 5 seam lower is far better than No. 5 seam upper, but would still require washing the coal. This makes No. 5 seam lower the preferred seam to mine because it meets the requirements of the customer which is Highveld Steel. It is a coincidence that the area containing No. 5 seam under investigation encounters high overburden problems. The problem of drilling to No. 4 seam was going to be encountered because the thickness of the overburden ranges from 35 to 39 m. The Gardner Denver at the mine can drill blastholes only to a depth of 34.5 m, meaning the full overburden will not be drilled at once. This means the mining of No. 5 seam will do favours for Eskom because the overburden thickness will be minimized. This then led to an agreement between Anglo Coal and Eskom to mine No. 5 seam because both companies benefit from the project. In order to identify a suitable mining method for No. 5 seam lower, literature studies took place. It is found that San Juan mine from the USA has similar geological features to Kriel Colliery's No. 5 seam. Through comparisons, it is found that truck and shovel mining would suit the geology of Kriel Colliery's No. 5 seam since San Juan mine is using it. The sequence of mining No. 5 seam lower allows for a clearance of two cuts between the truck and shovel operation and the dragline. The mining sequence of No. 5 and 4 seam will be in the order of top soil removal; soft overburden pre-stripping; pre-strip drilling; pre-strip hard overburden; No. 5 seam lower coaling; interburden drilling and blasting; interburden stripping and No. 4 seam coaling. Financial evaluation of the project shows that a contractor will charge Kriel Colliery (Anglo Coal) approximately R 102.2 million to mine No. 5 seam successfully. The sales of No. 5 seam lower will provide a profit of R99.4 million at a yield of 70% from the washing plant. The project is beneficial to both Eskom and Anglo Coal because Eskom will have eliminated the problem of pre-stripping and Anglo Coal will generate additional profit. Through investigation and analyses of the project, it is proven to be viable and should take place. This is after looking at the advantages that the project has for Anglo Coal and Eskom. Keywords No. 5 seam, truck and shovel mining, Kriel Colliery, No. 5 seam mining at Kriel Colliery opencast, Anglo Coal and Eskom, No. 5 seam upper and lower, top soil removal, soft overburden pre-stripping, pre-strip drilling, pre-strip hard overburden, No. 5 seam lower coaling, interburden drilling and blasting, interburden stripping, No. 4 seam coaling.

Jan 1, 2011

By E. Dermietzel

The fundamental ideas of Computer Aided Lignite Mining (CALM) with respect to hardware and software used at Rheinbraun are explained and outlined in detail. The computers used in the main data processing department and in the different departments in the mines are described. Special emphasis is laid upon the network connecting the computers at different places for data-exchange. Concerning technical applications, the main facilities of CALM are deposit and pit modelling, complex geomechanic computations and mass calculations, data recording from the production process in the pits and refining plants, and detailed information and planning systems for water management and mining equipment. Concerning administrative applications, the main facilities of the software are the accounting system with cost controlling and planning, the materials management system with stock control, forward planning and computer supported order procesing, a system for the administration of property within and surrounding the mines, and systems for personnel administration and payroll. The various software systems developed for these application and the influence of data processing technique, such as data base management and the interconnection of data processing systems, are demonstrated.

Jan 1, 1987

Copper cyanide is a common component of cyanide-treatable precious metal ores. The copper concentration in production heaps can be predicted from laboratory column tests, but the exact correlation is not necessarily intuitive. Generally, heap leach operators like to keep copper concentrations in solution below 300?500 ppm and may note problems with gold recovery and cyanide consumption when copper concentrations exceed this amount. There are several methods of copper removal from cyanide solutions including ion exchange; direct electrowinning; acidification, volatilization, and recovery (AVR); and sulphide precipitation such as the sulphidization, acidification, recycling, and thickening (SART) process. SART involves acidification with addition of soluble sulphide, separation of the resulting copper sulphide precipitate, and addition of lime to re-establish alkalinity prior to returning the solution to the leaching process, recovering both copper and cyanide as valuable products. In principle SART is very simple. Yet some SART plants that have been built may have been unnecessarily complex. This paper explores the basics of SART and makes the case for a simple plant design as applied to the heap leaching circuit.

Jan 1, 2012

By S. L. Miller

The development of a pilot gold geostatistical ore reserve system proved that geostatistical methods worked well for the routine production of annual ore reserves on gold mines of the Gold Fields of South Africa (GFSA) group, and that the techniques could also be practically implemented, understood and accepted by Survey Department personnel. Many side benefits of the pilot system became apparent, and a variety of useful management information was provided by manipulating the data values that were already captured. It was decided that it was a priority computing project to develop a standard production system (GORS) for routine use by all the GFSA gold mines. Experience with the pilot system enabled detailed functional specifications for GORS to be laid down. These, together with group computing policy determined the terms of reference and constraints for the GORS development. System design could not be finalized until new and appropriate mainframe database software and graphics workstation equipment and software had been found. With these in place the basic system was structured to take best ad- vantage of the interactive features of the workstation, the number-crunching power of the mainframe and the flexibility offered by a relational database and associated 4GL tools. Application sub-systems were developed for data capture, statistical applications, geostatistical calculations, contour plotting and graphical queries. GORS is being introduced to the mines in a phased manner with suitable documentation, training and support structures to enable it to be routinely and effectively used on a day-to-day basis by all group gold mines.

Jan 1, 1987

By J. Petersen, T. Moyo

Waste Printed Circuit Boards (PCBs) are a metals-rich fraction of electronic waste (e-waste) streams, and globally it has been demonstrated that they can be recycled gainfully to recover the metals. Reported successful cases of PCB recycling are carried out in large volumes, using high-level technology and high capital investment smelter house operations. This presents entry barriers for recyclers in developing economies where capital may not be accessible, and the waste volumes are not sufficient to warrant large scale operations. Hydrometallurgical processes have the potential to provide an option for the scalable processing of smaller volumes of PCBs and can be set up at relatively lower capital costs. However, to date, the hydrometallurgical treatment options available rely on precursor communition and classification processes that also require high capital and energy costs. This paper presents an overview of the work done under the Minerals to Metals signature theme towards understanding e-waste recycling processes and developing pre-processing and characterisation of PCBs in order to unlock potential for local end processing in developing economies, using South Africa as a case study. The structure of PCBs is reviewed, and the current size reduction techniques and the subsequent leaching processes are discussed. Keywords: Printed circuit boards (PCBs), PCB structure, pre-treatment, liberation, ammoniacal leaching

Jan 1, 2020

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions. Keywords value driver trees, production constraints, throughput analysis, capacity analysis, TOC (Theory of Constraints), activity interdependencies, unit cost reduction.

Oct 1, 2013

By T. Copland

"The decreasing availability of resources amenable to surface operations has led to increasing numbers of underground mines, with trends indicating this will continue into the future. As a result, there is a need for additional optimization processes and techniques for underground mines, with many analogous methods having already been developed for surface mining. Current methods for design and optimization of stope boundary selection and scheduling mainly involve heuristic methods which focus on a single lever. Individual optimality may be approached, but globally optimal results can be obtained only by an integrated, rigorous approach. In this paper we review previous methodologies for stope boundary selection and medium- to long-term scheduling and highlight the need for an integrated approach. Previous integrated approaches are reviewed and an improved modelling system proposed for shorter solution times and greater applicability to mining situations. Randomly generated data-sets for gold-copper mineralization are used to investigate the model performance, describing solution time as a function of data complexity.IntroductionThe increasing need for mineral resources is driving an increase in underground mines. Lower grade mineralization with larger amounts of overburden is becoming economically viable due to technological advances; however, the software and tools available for strategic underground mine planning are not well developed. Advances in the methods used to determine underground layouts and scheduling must occur to ensure underground mining is as optimized as open pit operations, as underground mining involves many more technical restrictions.The process of determining stope boundaries and scheduling is an example of an aspect of underground mining amenable to optimization (Topal and Sens, 2010). The current industry standard for medium- and long-term planning for sublevel stoping (SLS) is to exclusively determine stope outlines and then determine an appropriate sequence and schedule accordingly. This process violates the concept of optimality as integrating the constraints imposed by pre-determining stope outlines does not allow for considerations in scheduling to influence boundary planning (Ataee-Pour, 2005). An integrated planning process that combines both stope outlines and scheduling would approach the optimal solution and hence generate more value for operations. This investigation specifically deals with the underground sublevel stoping (SLS). Other underground mining methods such as block caving, sublevel caving, and room and pillar mining have unique characteristics and therefore require specific stope boundary/production scheduling considerations."

Jan 1, 2016

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By J. A. Maritz

Since the dawn of mining, pillars have been used as primary support to ensure stable workings. Early designs were based on trial and error, after which more scientific means developed over time. A vast amount of progress has been made, especially in soft-rock room-and-pillar design methodologies, from which hard-rock design theories developed with minor changes to constant parameter values. The commonly used Hedley and Grant method for hard rock and Salamon and Munro methodology for soft rock draw on the tributary area associated with the pillar, the width-toheight ratio of the pillar, and a back-analysed strength reduction factor. In these methods, only the vertical stress, or stress normal to the pillar influences the load applied to the pillar. This investigation considers the possible influence of shear stresses on pillars in a room-and-pillar layout in single reef planes and multi-reef environments, based on elastic numerical modelling methods. The possible shear stress poses a safety and financial risk to the design process, whereby an undersized pillar would lead to unstable working conditions, whereas oversized pillars could lead to an under-utilized ore resource.

Jan 1, 2014