Search Documents

By L. C. Ilaley

The Buresa. ot Mines at its Pittsburgh Station conducted tests aa earl7 a.a 1911 looking into the satety of miniature electric bulba. The first teata were maie with bulbs euch as were being sold with the partly developed lamps then on the market. 'l'he.sa aarly teats demonstrated the da.nger of using minia.tu:re bulbs in explosive mine atmospheres unless the current that enet gized the glow!ng filament was in aome minner inter.N.ptecl if the glass surrounding the filanant should be broken.

Jun 1, 1922

By Julie Mitchell, Robert King, Len Eros

The Bureau of Mines has studied the Deserado Mine computerized monitoring and control system, located in Rangely, Colorado, to acquire knowledge about the overall costs and benefits of mine monitoring systems. The Deserado system is a complex system monitoring environmental parameters, electrical power, and operation of all mine equipment, and controlling the entire conveyor haul age system. This paper discusses the evaluation of the Deserado monitoring system from initial design through system installation and operation. It also examines the costs, benefits, and performance of the monitoring system.

By M. K. Larson, J. K. Whyatt, R. B. Langston, J. C. Johnson, H. Kirsten, T. M. Brady

An experiment is described in which hollow inclusion cells (HICells) were used to measure stress in a jointed rock mass during drift development at the Stillwater Mine, Nye, MT, USA. Two HICells were installed in the footwall approximately two drift widths ahead of the face. One HICell was over cored and then immediately tested in a biaxial chamber. The other HICell was left in place and monitored as the drift was excavated in three advances, each one-half the width of the drift. Strains were recorded hourly by a datalogger. Results show that there was little stress change during the first and second drift advances, but that a large stress change occurred after the third advance. The measurements also showed that the in situ principal stress directions lined up with regional geologic structures. Stress changes during face advance were likely caused by deformation along localized joint sets and inelastic deformation near the face.

By Stephen L. Tillim

Tubular Handles can negatively affect the contents of the carpal tunnel. Years of injuries from grasping handles for tools and machines can cause carpal tunnel syndrome, tendonitis and wrist joint injuries. The can cause inability to use a hand and resulted in the longer absences from work than injuries from falls, accidents or fires.1 Cylindrical, tubular and rectangular handles are rolled flat structures. They place the hand on a rolled flat surface where the ends of the middle and ring fingers overlap the index and small fingers. They are pulled along a series of lines that contact the end joint of the index finger, the middle bones of the middle and ring fingers and the end bone of the small finger. Cylinders are pulled diagonally in the hand toward the carpal tunnel (CT) area. Gripping in this manner tenses asymmetric muscle groups in the forearm. Handles could work better if they do not place pressure on the CT and conform to the natural function or neutral hand position where the hand rests or dangles at the side of the body, the finger tips form a diagonal, the palm and fingers form a cup, the thumb rests between the index and middle fingers and the wrist is mildly extended. However, handles designed for the neutral position are pulled by diagonally oriented fingers into the valley between the thenar and hypothenar muscles where they can compress the median nerve and tendons exiting the CT. Seven principles for handles that do not place pressure on the carpal tunnel and employ optimal hand position are presented. First, handles should align the ends of the fingers parallel to the horizontal crease and not diagonally. Second, handles should extend from the cupped fingers to meet the muscles at the base of the thumb on the radial side of the hand and extend further on the other or ulnar side to meet a portion of the small muscles. Third, handles should have a recess on the proximal side to prevent contacting or placing pressure on the carpal tunnel. Fourth, handle design should be based on hand measurements in a position of function. Fifth, handles should come in sizes. Sixth, handles should be placed on tools to maintain the wrist and elbow in neutral position. The seventh is handles should support the maximum area of the hand and absorb, but not direct, vibration to the carpal tunnel. These principles led to prototypes and patents for handles for gripping, pinching and squeezing2,3,4 . The poster will illustrate and explain the principles Bonsil handles. Research, with existing tools, is needed to substantiate claims made for the Bonsil handle.

Jan 6, 2006

Homans [1950] offered a working definition of group that is useful for this research: "We mean by a group a number of persons who communicate with one another often over a span of time, and who are few enough so that each person is able to communicate with all the others, not at secondhand, through other people, but face-to-face." This chapter begins with a discussion of the group concept in reference to the hypothesized escape groups mentioned earlier. It then moves to an examination of analysis techniques used by the authors. Finally, the subjects themselves are profiled according to their demographic characteristics. The Nature of Groups Warriner [1956] took a realist approach to understanding groups: "(1) the group is just as real as the person, but (2) both are abstract, analytical units, not concrete entities, and (3) the group is understandable and explicable solely in terms of distinctly social processes and factors, not by reference to individual psychology." Warriner's realist position merely holds that "group" occupies a different domain in which it is no more or less concrete than "person." At this group level the unit of analysis will be those relations that indicate social rather than individual behavior. It is possible to investigate these group properties empirically-if a researcher avoids confusing conceptual entities with concrete ones. Most people seem to accept that group attributes must somehow be inferred, but think personal attributes will be directly manifested, requiring little or no interpretation [Snizek 1979]. In other words, nobody would equate physical components of an underground working section with the actual work group, yet social scientists (as well as laypeople) very often confuse real individuals with notions of the person. In actuality, neither groups nor persons are directly disclosed to the senses; both are inferred by experience and observation. One can "see" a group just as clearly as one can "see" a person, given the proper perspective from which to do so. It is necessary, in developing this perspective, to begin with a sound definition of the thing being examined. Besides communication, or more generally, social interaction, Homans [1950] included three other components of group makeup. "Sentiment" is characterized as the feelings people tend to form about one another when they interact often. These feelings include not only friendliness and dislike, but attitudes such as approval or disapproval. A "norm" is an idea, held in common by group members, that specifies how people ought to behave in given circumstances. In lay terms, norms are simply those informal rules individuals abide by in order to get along together in social situations. Finally, "activity" refers to those things persons do with others. In work groups, as an example, many of the activities are cooperative and goal-directed.

Jan 1, 2000

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 44,015 employees worked in underground mining locations in 2003, corresponding to 44,778 full-time equivalent (FTE) workers. • Ninety percent of underground employees (n = 39,735) were mine operator employees. • Contractors comprised 10% of all underground mining employees (n = 4,280) and comprised only 5.8% of all underground FTEs. • The majority of underground employees worked for coal operators (73.0%; n = 32,130).

Feb 1, 2005

By James C. Cawley

A summary is presented of existing leaky feeder communications systems currently in operation in North America. Background information pertaining to previous use of leaky feeder technology is discussed along with the survey methodology. A review of some pertinent facts concerning propagation in tunnels and specific reference to mine tunnel propagation is presented. A summary of the characteristics of each mine visited is presented in tabular form, and methods of procurement and maintenance are discussed. The role of user training in efficient system use is presented. Seven sites representing eight mines are included in the survey. Economic and technical topics are considered.

By Charles L. Kimbell

This study is intended to serve three roles. First, it represents a global overview and summary to supplement and complement the five regional companion volumes of the 1991 edition of the Minerals Yearbook International Review. In this regard, it also extends previous time series under this title that appeared as the introductory chapter to the international volume of the Minerals Yearbook from the inception of that volume in 1963 until it was subdivided into separate regional volumes in 1989. The basic statistical presentations herein generally contain data through and including that for 1991, although in a few instances the most recent statistics are those for earlier years because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting the world's mineral industry that have occurred between the end of 1991 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

By Gerrit V. R. Goodman, Fred N. Kissell, Charles D. Taylor

In This Chapter [Methane emission peaks Exhaust line curtain or duct The spray fan system Dust scrubbers with blowing ventilation Dust scrubbers with exhaust ventilation The ventilation of abnormally gassy faces Methane detection at continuous miner faces Ventilation and methane detection at bolter faces and Reducing frictional ignitions] This chapter gives guidelines for preventing methane gas explosions at continuous miner sections in coal mines, both at continuous miners and at roof bolters. The need to control peak methane emissions is particularly stressed. Emphasis is also placed on ventilation principles, monitoring for gas, and reducing frictional ignitions. METHANE EMISSION PEAKS Methane emission from the coal at continuous miner faces varies considerably. Plotted on a chart, methane emissions consist of a series of peaks and valleys corresponding to the cutting cycle of the mining machine, with the methane concentration spiking as the machine cuts into the coal (Figure 3–1) [Kissell et al. 1974]. These methane peaks can be substantial. For this reason, efforts to safely dilute the methane must focus on the level of the [ ]

Jan 6, 2006

By Edward D. Thimons, Jay F. Colinet

Underground coal mining operations in the United States continue to increase productivity as mining equipment and practices are improved. Unfortunately, increased production also results in the potential for increased respirable dust generation and worker exposure. In response, US operations are applying basic controls at elevated levels and looking to emerging technologies in an effort to better control respirable dust levels. Ventilating air and water sprays remain the basis of dust control strategies for both longwall and continuous mining operations, and the level of application for these controls continues to increase. In addition, new technologies are emerging that have the potential to further reduce dust levels. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research into methods to optimize existing control technologies and evaluate emerging control technologies. This paper will summarize control technologies routinely being used in underground coal mine operations, as well as provide a review of new controls that are being pursued.

By R. V. Ramani, V. T. Burgos, J. A. McClay

The systems contributing to the cost analysis, and the flow of data input and output related to these systems, are brought into focus in Figure 6. The various sub-systems of the Master Design Simulator provide the raw operating data basic to the cost model which, operating independently, accumulates the raw input, assigns costs to this data by standard or modified costing procedures, manipulates the costs into standard formats and outputs the data for managerial evaluation. Cost Modeling Direct costing methods are not complex in the sense that elemen¬tary arithmetic is employed using the same basic relations for each cost category. The basic cost model relations described above are illustrated in Figure 7. The greatest difficulty encountered in the transition from a dy¬namic systems simulation model to a costing model is the time frame of the input and output data. Dynamic simulation models utilize a small time increment, on the order of seconds or fractions of seconds, to analyze system operations and interactions. On the other hand, for cost computation and reporting, the smallest relevant time unit is the shift, with reporting periods expanding to days, weeks, months, and years. Complications arise in the accumulation of data for the various report periods due to the use of the Gregorian calendar by modern so¬ciety. The potential for simulation for the life of the mine, possibly in excess of 50 years, increases the complexity of the costing process

Jan 1, 1975

Jul 1, 2003

By M. Brnich, L. Mallett, C. Vaught, K. Kowalski

This paper discusses the data collected during an emergency evacuation training exercise at an underground mine in the United States. The focus of this paper is on the human reaction to smoke and the use of personal protective equipment. Specific issues related to the human stress response during an emergency will be discussed.

By Elaine T. Cullen

Educating the public about the role of mining and minerals can be a challenge. While it sometimes seems that little is being done to counteract negative publicity, there are many exciting things happening across the country that are helping meet this challenge. This paper will discuss existing minerals education activities and will provide tips for developing successful programs for a variety of groups, from students to industry to minerals educators themselves. The paper will also include an overview of the 9th annual National Minerals Education Conference held in July 2000 in Spokane, WA.

Reduce the dust exposure of workers in large processing buildings at mineral processing operations, using a total mill ventilation system.

Jan 1, 1994

By D. Harrington

"The fire boss in coal mining and the shift boss in metal mining, though held responsible to a large extent for safety of underground employees and of the mine, are, it seems to me, not always vested with sufficient authority nor given compensation commensurate with their duties. The metal-mine shift boss, although his position as regards his relations between employer and employee, is frequently an unenviable one, has as a rule much more authority than the fire boss and is not expected to perform the menial tasks required of the latter by many coal-mining companies.In most coal-mining States the coal-mine foreman and the fire boss are re¬quired to possess a certificate of competency obtained by passing an examination. The foreman is legally responsible for the safety of the miners, as in most instances the superintendent is not required to pass an examination. Although the foreman is held legally responsible for the safety of the miners, the law does not, in general, compel the superintendent or other higher officials to delegate sufficient authority to the foreman to enable him to put his wishes or judgment into effect; and this condition has tended in many instances towards perpetuation of unsafe conditions.The fire boss is held legally responsible for conditions in his ""beat"", but he is generally given only such authority as the mine foreman sees fit to delegate, frequently very little, Moreover, the fire boss is generally required to cover his ""beat"" within two hours before the entrance of the underground workers. Only too often his territory is so great that in order to reach all the working faces and chalk the required date at the face, he must travel at a rapid walk or even run. When such haste is necessary to cover the required ground, it is manifestly im¬possible for the fire boss to make a careful inspection or examination of the roof, timbering, wiring, gas, etc., at each place, and doubtless in his hurry many unsafe conditions escape his notice."

Sep 1, 1920

By R. D. Leitch

In the course of another investigation4 during 1926 and 1927, samples of water collected from a few abandoned coal mines indicated that their drainage was usually lower in acidity than water from active mines in the same locality. In order to determine whether this condition might have a bearing on the advisability of sealing abandoned mines, a number of such mines were visited, samples of drainage were collected, and as much information as possible was obtained from officials of the mining companies and older residents of the district. The results of this work are the basis of the present report. ACKNOWLEDGMENTS The authors are indebted to E. W. Robertson, F. F. Spowart, J. H. Nagle, and W. D. Adams of the Northwest Mining & Exchange Co.; E. M. Fasset, Fred Lane, Wm. Humphreys, and Dr. T. A. Hutchison of Brockway, Pa.; C. W. Faulk of the Shawmut Mining Co.; James Hau of Kersey, Pa., and do others for information received; and to Dr, R. R. Sayers of the Bureau of Mines, under whose direction the work was conducted.

Jan 1, 1928

By J. Whyatt

A package of bench design programs is being publicly released by the National Institute for Occupational Safety and Health (NIOSH). These programs are designed to provide a probabilistic estimate of the likelihood that various widths of catch bench will be retained. Program modules address the mechanisms of plane, plane step path, and wedge failure. Results are drawn from statistical and geostatistical descriptions of fracture characteristics and other input parameters, and reported as the statistical chance that a given width of catch bench will survive, that is, that a catch bench will remain wide enough to catch rolling and sliding material and prevent such material from posing hazards to miners operating below. The capabilities and application of this software are demonstrated through a case example. Comparing bench width estimates obtained using geologic data with actual widths is a key step in verifying that a program is appropriate for particular site conditions and that proper statistical descriptions of fracture parameters for that site have been developed. Such verification efforts improve confidence, and hence usefulness, of this method for designing future slope benches. Development and release of these programs appears particularly timely given recent progress in photoanalysis methods, which promise to greatly reduce the cost of collecting fracture data.

Jan 1, 2004

New Continuous Personal Dust Monitors (CPDM) submitted to NIOSH for approval to sample coal mine dust must accurately measure respirable coal mine dust in mine environments. There are two steps in the process which may be done in any order. The manufacturer is required to submit the results of a comparative underground coal mine dust sampling study, where the candidate CPDM is compared to an approved coal mine dust sampling device (currently the Coal Mine Dust Personal Sampling Unit (CMDPSU)). This testing shall follow the guidelines outlined below and shall demonstrate through weighted regression analysis that the mean coefficient of variation with bias correction is equal to or less than 12.8%. The other step involves laboratory testing to determine the electronic and environmental stability. This testing must be conducted by a private, commercial, academic or other laboratory approved by NIOSH.

Jan 1, 2009

By J. D. Noll

The Mine Safety and Health Administration (MSHA) has promulgated rules to limit the exposure of metal/nonmetal underground miners to diesel particulate matter (DPM). These rules have resulted in many types of control tech­nologies being implemented including diesel particulate filters (DPF). The passive type DPF is the most desirable because it requires little maintenance and it regenerates while the vehicle is operating. One problem with passive DPFs is that many vehicles cannot develop the sustained exhaust temperatures needed to initiate DPF regeneration, and thus it is required that the DPF be catalyzed to decrease the temperature needed for regeneration. In some past studies, such catalyzed filters have been shown to cause an increase in the nitrogen dioxide concentrations in the exhaust, resulting in a potential health hazard. In this study, a lightly catalyzed DPF along with a fuel-born catalyst were employed to help reduce the DPM emissions from a 980F loader used for cleanup in a stone mine. After 30 days of use, the filter continued to regenerate successfully at the exhaust temperatures generated by this loader, substantially reduced DPM concentrations emitted in the exhaust, and did not cause a measurable increase in nitrogen dioxide levels that could be attributed to the device.

Jan 1, 2009