Search Documents

Reduce longwall intake contamination by controlling respirable dust generated by the stage loader. Approach Install a water-powered scrubber on the stage loader immediately outby the crusher. Dusty air from the crusher is drawn through the scrubber and a clean air discharge is delivered into the primary face airflow. How It Works The contamination of intake air is a significant dust control problem often overlooked on many longwall faces. This dust source contributes to the full shift dust exposure of all face personnel, and thus can significantly affect compliance with Federal regulations. Several sources contribute to contamination; however, dust generated by the stage loader crusher is the single largest source. The breaking action of the crusher generates a tremendous quantity of dust, which mixes with the primary ventilation airstream and is carried down the entire length of the longwall face. The installation of a water-powered scrubber (see diagram) has proven effective in controlling crusher-generated dust. The scrubber is mounted immediately outby the crusher. A duct is placed over the scrubber intake and attached to a flanged opening over the crusher discharge. In

Jan 1, 1982

By Jeffrey Johnson, Thomas Brady, Radford Langston, Mary MacLaughlin, Hendrik Kirsten

The magnitudes and directions of in situ stresses affect the stability of mine openings, as well as the type and amount of ground support needed to maintain a safe working environment for miners. Using hollow inclusion stress cells, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health obtained two in situ stress measurements from the face of two footwall lateral drifts at the Stillwater Mine near Nye, MT. The first measurement, obtained in 1997, was collected under the valley beneath the Stillwater River. The second measurement was obtained in 2002 under the main frontal massif of the Bear tooth Mountains in the western sector of the mine. Although few data are available, the major principal stress under the valley has been recorded as nearly horizontal in a north-south direction perpendicular to the ore body, while beneath the mountains, stress runs east-west parallel to the ore body. This paper documents the measurements, describes the in situ stress state, and discusses a finite-difference analysis of the biaxial test.

Provide a rapid, reliable means of warning underground miners of a fire or other emergency. Approach An ultalow-frequency electromagnetic signaling system was designed, breadboarded, and tested at various under around mines. How It Works Current fire warning systems for underground mines, such as stench, audible alarms, and messengers, arc slow, unreliable, and seldom achieve total mine coverage. An ultralow-frequency electromagnetic fire warning alarm system with true through-the-earth signaling capabilities was developed to solve these problems. The system was originally designed for high-back room-and-pillar mines where stench systems are unusable due to the low velocity of mine air flow. However, the system has an application to all underground mines.

Jan 1, 1988

To quickly and reliably assess the stability (safety) of saturated and unsaturated tailings pond embankments. Approach Determine embankment geometry and soil properties, then use that data to obtain the safety factor of the embankment directly from one of a series of factor-of-safety charts.

Jan 1, 1982

Determine the effectiveness of remining operations in reducing contaminant load (acidity, iron, and sulfate) of discharges emanating from abandoned surface and underground coal mines. Background Until the implementation of remining initiatives, most States had regulations that held the operator remining an abandoned site responsible for preexisting acid mine drainage (AMD) discharges. For example, if a mining. company wanted to remine an area hydrologically connected to an existing AMD discharge, the company became responsible, as soon as the site was activated, for treating that discharge to meet effluent standards. If the mining operation improved the quality of the discharge, but the discharge failed to meet effluent standards, the company was held accountable for perpetual treatment. Because of this regulation, most mine operators avoided abandoned sites with minable coal reserves and AMD discharges. However, changes in remining legislation allow coal companies to be released from treatment liability as long as the post-remining pollution load does not exceed the pre-remining level. If remining can improve water quality through improved mining and abatement techniques, abandoned mine land (AML) areas that previously were liabilities could become

Jan 1, 1994

By J. Brad Seymour, Mark K. Larson, Richard L. Rains, Douglas R. Tesarik

For several years, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) have been using geotechnical instruments in underground mines to study ground control problems and develop means of reducing accidents and fatalities caused by ground falls. This paper describes many of the different types of instruments, sensors, and data acquisition equipment that have been used for these studies; briefly explains the advantages and disadvantages of various sensor technologies; provides practical recommendations regarding the use of specific instruments and data acquisition systems; and outlines a general approach to the design and implementation of a successful instrumentation plan. A wide variety of instruments are commercially available for measuring deformation, strain, stress, and/or load. If used correctly, these instruments can provide important quantitative information regarding the mining-induced behavior of the host rock, the performance of ground support systems, and the safety and stability of underground workings. Data collected from these instruments can warn mine staff of impending ground control failures or hazardous working conditions, as well as provide valuable information for the design of ground support systems and the configuration and sequencing of mining excavations. We hope that the practical information presented in this paper will encourage a more widespread use of geotechnical instruments in underground mines and lead to reliable measurements that aid the engineering decisions affecting the safety of miners.

Jan 10, 2000

Measure tattling in cemented backfill when installation of bore-hole extensometers is not feasible. Problem To evaluate the amount of load that backfill carries during pillar recovery, information about how much the backfill settles after placement is often required. However, the composition of some backfills makes them difficult to drill and the installation of borehole extensometers almost impossible. Approach Bureau researchers have developed a vertical fill extensometer that can be cast in place as a stope is being filled. It consists of a baseplate, sections of steel pipe enclosed in loosely coupled polyvinyl chloride (PVC) pipe, and a top anchor assembly that contains a displacement transducer (fig. 1).

Jan 1, 1990

Develop a 22-ton capacity temporary mine roof support light enough to be easily lifted and transported manually from one place to another. Approach Several potential approaches were investigated in developing a new temporary support. An all-hydraulic, high-strength aluminum design was chosen as the best. The support was designed, fabricated, and tested in several mines. The first units, built for 6- to 8-foot seam heights, have a load- bearing capacity of 22 tons, and weigh only 55 pounds. How It Works The lightweight hydraulic support is designed for use in any temporary support situation in place of wood posts or steel mechanical or hydraulic supports. This includes use prior to roof bolting in room and pillar mining and in longwall development sections, use as head and tailgate supports for a longwall, and use as turn posts and breaker posts in retreat mining operations. The supports feature a release valve for quick manual extension to roof level, a lanyard

Jan 1, 1983

Determine the dust reduction capabilities of various bag valves available to the minerals processing industry. The Problem Many different types of ground mineral products are packaged into 50-and 100-lb paper bags. Although bag technology is continually improving, dust contamination from bags still remains a significant problem for workers. The greatest source of dust is the bag filling valve. Ideally, the bag filling valve should close after it fills the bag with the ground mineral product. However, the valve usually fails to close properly since some mineral product gets trapped inside the valve during filling and ejection. As a result, when the bag has been filled and falls from the fill station, a rooster-tail of product is discharged from the bag valve. As the bag hits the conveyor belt, additional product discharges from the bag valve. The dust from these sources contaminates the air inspired by the workers filling the bags as well as the work area. Dust also clings to the outside of the bag, contaminating the pallet loading station. Because the various commercial bag valves are composed of different materials, a dust analysis was performed on five of these valves to determine their dust reduction capabilities. The five valves analyzed were: standard paper, polyethylene, extended polyethylene, double trap, and foam.

Jan 1, 1986

Design a high-production coal mining machine with inherent low dust generation and low frictional ignition potential. Approach Constant depth linear cutting (CDLC) provides a longterm solution to excessive dust generation from shearers and continuous mining machines through new design of the rotary drum culling system. Problems with rotary drum systems, which must be eliminated to control the dust generation at the source, include the effect of a con¬stantly varying depth of cut using fixed bit spacing, secondary fragmentation of already broken coal and, frictional heating of bits and entrainment of dust by fanning action due to high drum rotational speed, Each bit on a rotary drum enters the coal face at zero depth of cut, goes to some maximum depth at the horizontal centerline during sump, and exits at zero depth.

Jan 1, 1989

By Liming Yuan

In order to reduce fire hazards caused by spontaneous combustion in longwall gob areas, a computational fluid dynamics (CFD) study is being conducted by National Institute for Occupational Safety and Health (NIOSH) to simulate the spontaneous heating of coal in longwall gob areas. A CFD model was first developed to model the spontaneous heating process in a two longwall panel district using a bleeder ventilation system with a stationary longwall face. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory-scale spontaneous combustion studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. CFD simulations were then conducted to model the spontaneous heating in longwall gob area with a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated. The effect of gob permeability on the spontaneous heating was also investigated.

Jan 1, 2009

By J. G. Walters

The method for predicting coke strength developed at Steinkohlenberg-bauverein, Germany, in which experimental parameters are readily determined by small-scale laboratory tests, was found to be applicable to cokes produced from industrially used blends of American coals. Predicted 1-inch ASTM tumbler indices for four industrial blends were found to be in excellent agreement with the experimentally determined values. The laboratory determined prediction parameters include the proximate analysis of the coal the size consist of the coal, and Ruhr dilatometer test data.

Jan 1, 1971

By H. J. Sloman

"INTRODUCTION Industry, including coal mining, has come to realize that to prevent accidents the human element must be given more consideration than was customary in the past. In formulating safety rules and regulations and in the enactment of laws governing mining, too often enforcement is emphasized rather than the means of gaining willing compliance.' The purpose of this paper is to call attention to the human side of accident prevention, and the approach to this important and much-discussed subject will deviate somewhat from the usual discussions.The human being is a complex mechanism, both physically and mentally. It is difficult to establish a common denominator for the actions of humans, except in general. In establishing mining laws, rules, regulations, and standards, the ultimate objective should be to gain the best possible response of workmen, so that optimum results in accident prevention may be obtained. The complexity of human beings is apparent when the many ways 1n which they differ are considered. Some of these differences are manifested in emotional and phlegmatic types, degrees of intellect or native intelligence; and in hopes, desires, aspirations, and philosophies of life. How much simpler ac¬cident prevention would be if the response to laws, rules, regulations, or standards were equivalent to the definite movements of puppets responding to pulls on strings. Each time, the strings are pulled in exactly the same way, the puppets will respond in exactly the same manner. Human beings, although having many similar characteristics, do not respond uniformly to identical ""string-pulling""; therefore, much study is necessary before the desired re¬sponses can be obtained. To achieve the ultimate in accident prevention, it must be ""worked at"" constantly. Regardless of the adequacy of safety laws, rules, regulations, or standards, good accident records will not ""roll in"" if dude consideration is not given to the personal traits of those most likely to be involved in accidents."

May 1, 1948

Minimize airborne respirable quartz dust produced by continous mining machines. Approach Install a shovel-mounted underboom water spray system on the off-curtain side of the mining machine. Dusty air containing quartz is momentarily trapped under the boom, where it is captured by fine spray mist. The remaining dust cloud is directed immediately behind the curtain before it can migrate back to the machine operator's location. How It Works Previous studies have shown that most of the dust generated by continous mining machines occurs under the boon as the cutter head shears down. The primary source of respirable quartz dust on many continous mining operations is cutting or trimming roof rock immediately prior to shearing. This results in very high concentration , of

Jan 1, 1989

By Robert L. Crosby

The Bureau of Mines investigated the substitution of cement copper powder for commercial copper powder in an Fe-7 pct Cu-l pct C powder metallurgy alloy. Copper powders from six different commercial cementation operations were separately upgraded by screening and hydrogen reduction. They were then mixed with commercial iron and graphite powders to form the Fe-7 pct Cu-l pct C alloy. Various chemical and physical properties were determined on the upgraded cement copper and the alloy powders. Mechanical, physical, and chemical properties were determined on green and sintered specimens made from the alloy powders. Mean tensile and bending strength of sintered specimens were significantly lower than the means from specimens made from commercial metal powders. The lower strengths are apparently related to poor sinterability.

Jan 1, 1970

SCOPE AND APPLICATION The rules cover the installation and use of electrical equipment in coal mines.- For generating stations, substations, lines, and equip¬ment aboveground, reference is made to existing rules covering such locations, viz, the National Electrical Code and the National Electrical Safety Code and any existing State or municipal regulations. The purpose of the rules is to set forth methods for safe electrical installation. In preparing the rules five basic measures for safe¬guarding the use of electricity in mines have been followed, viz 1. Remove the contributory causes of accidents or danger. 2. Remove from the vicinity of electrical apparatus all elements susceptible to the influence of electricity. 3. Keep the electric current where it belongs, if possible; if not, limit the area of its activity by protective devices. 4. Use a. large factor of safety in the selection, installation, and in¬ spection of equipment. 5. Have full control of the operation of electrically driven machines. Each rule that is given is proposed as necessary or helpful to the accomplishment of one or more of these measures. DEFINITIONS OF TERMS USED Alive.-See definition of " live." Approved.-The term " approved " means accepted as suitable by a competent committee, board, or organization designated by those adopting the rules. Authorized person.-The term " authorized person " means a per¬son appointed or permitted by the official designated by the State mining laws as the one in charge of the operation of the mine to carry out certain duties incident to the generation, transformation, and distribution or use of electric energy in the mine, such person be-

Jan 1, 1926

Minimize drilling time in roof bolting. Approach The Bureau of Mines conducted a survey of 34 roof bolting machines used in underground coal mines. Results of the survey indicated that drilling time, bit cost, and respirable dust concentrations and be reduced by using the appropriate bits for drilling, To evaluate bits currently used and to find optimum cutting parameters needed to minimize drilling time, the Bureau tested two bits commonly used in most underground mines on both wet and dry systems. These are the dusthog* and shank type. The dusthog has dust ports in the bit body to remove cuttings. With shank bits, holes in the drill steel do this. Cost of each type is roughly equal. Bolters with dry vacuum systems were tested in the laboratory first. The lab tests were verified by underground tests in several mines. Bolters with low-pressure wet drilling systems were also tested under-ground. Tests concentrated on the effect of rpm, water and airflow rates, heating, wear, bit design and bit type. Lab Results -Dry Drilling Holes were drilled during the laboratory tests using a production model bolter drilling 45-inch-deep holes into mixtures of lime stone and sandstone aggregate. All tests started with new shank and dusthog type bits at 225 and 450 rpm. Thrust was about 6,000 lbs in all tests. Each bit was tested at two airflows, 15 and 25 cfm, airflows which are typical on operating roof bolter bits. Eleven styles of bits were evaluated. On the average, dusthog bits drilled 25% faster than shank types and were always cooler after drilling. The effect of RPM was tested with 5 different bit types. When bit rpm was increased from 300 to 400, drilling rates doubled. With used, well-worn bits drilling time and final bit temperature were more than doubled.

Jan 1, 1986

Simplify the spraying of sealants onto coal mine roofs. Approach A nonclogging system in which dry-fed sealant is mixed with water down-stream of the spray nozzle, has been developed and tested. How It Works The two-channel nozzle of this spray discharges two separate flows, a mixture of air and dry sealant from a central cylinder, and an encircling spray of water from a concentrically mounted water ring (a ring-shaped manifold). Downstream of the nozzle, the water mixes with the air and sealant to form a wet sealant spray that adheres to mine surfaces with very little rebound. (See photograph.) Extensively modified commercial spray machines are used to feed the sealant to the spray nozzle smoothly, without raising dust. Plugging of the nozzle is practically eliminated by two self-cleaning design features of the nozzle. These are the air gap and the tapered bore of the cylinder, (See drawing.)

Jan 1, 1979

By Richard J. Mainiero, Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small-scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single-hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

By C. A. Komar

Hardness, tensile strength, and impact toughness of dry and brine-saturated sandstone specimens were measured at ambient, cryogenic, and elevated temperatures as a measure of the relative stability of reservoir rocks for subsurface disposal of liquid wastes. Hardness measurements were inconclusive. Tensile strength and impact toughness were significantly higher at -320° F than at ambient temperature, but were relatively unaffected at 700° F. Impact toughness was reduced by subjecting the specimens to three cycles of rapid temperature changes (thermal shock) over a 1,000° F range. Tensile strength of brine-saturated sandstone was less than that of dry sandstone. Based on results of the tests, reservoir sandstone likely would be stable if exposed to extreme temperatures of liquid wastes, although rapid changes in waste temperatures should be avoided.

Jan 1, 1971