Search Documents

By B. W. Gandrud

In the summer of 1950, Bureau of Mines engineers visited a number of coal-preparation plants in western Europe and Great Britain to obtain information on European and British coal-cleaning and froth-flotation practices. In view of the growing importance of froth flotation as a process for cleaning fine sizes of coal, it was felt that such data and information would be of value in this country, for, although froth flotation has been adopted for use in a few of our plants, it has not as yet been employed as extensively as in British and European preparation plants. Many of the important coal beds in western Europe, especially in the Ruhr Valley of Germany and in the Dutch coal-mining region of Limburg, Netherlands, are very friable, with the result that the run-of-mine product contains a large proportion of the sizes too fine to be treated successfully by any other method than froth flotation. Furthermore, the relatively high cost of producing coal from these beds has for many years made it economically feasible and desirable to treat the fines by froth flotation, especially in the coking-coal fields.

Jan 1, 1951

By Fred Garcia, William P. Diamond

As part of its mine safety and health research program, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, has been investigating the geologic and mining factors influencing methane gas emissions associated with longwall mining. A primary focus of this research has been the consequences of increasing longwall panel dimensions, particularly face width, in gassy coalbeds. Continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). Average longwall pass methane emission rates for 229-m (750-ft) wide faces were 61 % (0.072 m31sec (153 cfm)) higher at the VP-3 Mine than at the VP-1 Mine. It was predicted by regression analysis of methane emissions data from 229-m (750-ft) wide faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7%, or 0.009 m3/sec (20 cfm), to 0.144 mysec (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces to 305 m (1,000 ft) at the VP-3 Mine would increase methane emissions by as much as 13%, or 0.029 mysec (65 cfm), to 0.268 dlsec (567 cfm).

Jan 10, 1999

By Linda L. Chasko, Charles P. Lazzara, Ronald S. (deceased) Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

Jan 12, 2005

By Jon K. Ahlness

The Bureau of Mines, in cooperation with the Institute of Mineral Research of Michigan Technological University, and the Upper Great Lakes Regional Commission, conducted an investigation of electronic sorting of native copper ore from Upper Michigan. This report is based on research by the Institute of Mineral Research under contract to the Bureau. The test program evaluated the use of belt and rotary sorters on various size and grade fractions of ore. Both plant-scale sorting and lab sorting tests were run. The plant sorting objectives were to determine the sortability of different ores and the efficiency of the electronic ore sorters. High-and low-grade ores from both conglomerate and amygdaloid types were separated into four size fractions. The two larger sizes were sorted on belt sorters and the two smaller ones on rotary sorters. Copper recoveries ranged from 20.0 pct from a feed grade of 0.40 pct to 80.3 pct from a feed grade of 1.08 pct. Lab sorting tests of conglomerate ore were run to determine the efficiency of a belt sorter equipped with a second sensing coil located above the belt and to determine the sorting characteristics of larger ore size fractions than those used in the plant sorting. Copper recoveries from the combined feed sizes ranged from 47.0 pct from a feed grade of 0.13 pct to 96.8 pct from a feed grade of 4.87 pct. For all the ore types except one, it was found that the copper recovery increased with the feed size.

Jan 1, 1980

By James Rowland, Isaac Zlochower, Richard Mainiero, Michael Sapko

The National Institute for Occupational Safety and Health (NIOSH) carried out exploratory laboratoryscale studies to identify factors that may contribute to nitrogen oxides (NOx) production associated with non-ideal detonation of blasting agents. Explosive admixture with drill cuttings, loss of fuel oil in ammonium nitrate and fuel oil (ANFO) from wicking, ammonium nitrate dissolution with water, degree of explosive confinement, ANFO density, and critical diameter were identified as contributing factors to increased NOx production under the laboratory test conditions. Experiments were also conducted to examine the effectiveness of various additives in reducing the NOx production from ANFO, emulsion, and ANFO/emulsion blends. Aluminum powder, coal dust, urea, and excess fuel oil in ANFO formulations were tested and were found to reduce both the nitric oxide (NO) and nitrogen dioxide (NO2) production. Fumes measurements were obtained in the NIOSH underground closed chamber from the detonation of 4.5-kg (10 lbs) charges in schedule 80 seamless steel pipe and from detonations in light weight galvanized steel stove pipe. Some exploratory tests were also conducted with 0.8-kg (1.8 lbs) charges of pulverized ANFO initiated with 0.08-kg (0.18 lbs), 50/50 (Pentolite) boosters (in the NIOSH 12-ft (3.7-m) diameter steel sphere) to measure the degree of fumes production associated with post-detonation oxidation. Ammonium nitrate, emulsion and Pentolite boosters were also detonated in an oxygen-poor environment.

By John Redington

This paper describing the milling practice at the Coniaurum Mine is one of a series of papers on milling methods, practice, and costs prepared in cooperation with an published by the United States Bureau of Mines. The 500-ton will of the Coniaurum Mines (Ltd.) is located at approximately the center of the company's property and a little more than a mile from the town of Schumacher, Ontario. The main shaft through which all the ore is heisted is adjacent to the mill so that the ore hoisted in a 3-ton skip is dumped directly into a 15-ton bin at the crusher.

Jan 1, 1931

By A. B. Hooker, L. C. IlsLey

The greatest hazard of early mining was from explosions of methane ignited by open lights . With the advent of safety lamps and forced ventilation this hazard was greatly reduced until the application of electricity to modern mining not only multiplied the sources of gas ignition but the accompanying , machines and haulage systems increased the amount of explosive dust , through which a methane explosion is more liable to become a major mine disaster , and thus greatly furthered the need of adequate ventilation to keep down the concentrations of methane . Adequate ventilation is still the best preventive of such explosions . However , even with a well laid out and controlled ventilating system the amount of air passing through entries and rooms is liable to vary within wide limits because of open doors , falls of rock , or other accidental causes . The percentages of methane under normal conditions should therefore be kept so small that they will not be increased to explosive proportions by short interruptions in ventilation . Mine ventilation and methane detection are inseparable safety precautions . The increasing importance of ventilation necessitates more accurato determinations of the methane concentrations throughout the mines . This paper discusses in detail some of the steps in the development of methane detection and specially notes the more accurate detectors now available . One of the earliest means of detecting methane was by a candle . About 1835 , John Buddle , Sr. , a noted mining man of his period , when questioned by a Parliamentary Committee as to the safety of using candles , replied :

Jun 1, 1933

By Launa G. Mallett, Kathleen Kowalski-Trakofler, Robert H. Peters, Charles PH. D. Vaught, Peter Keating, William J. Wiehagen

On-the-job training is a common means of training or retraining workers and the practice may seem simple and straightforward. Doing it effectively however requires more thought and preparation than simply having someone follow an experienced worker around and watch what they're doing. Over the years, various techniques and practices have evolved that pass on the skills and knowledge of a trainer or coach in a manner that leads an inexperienced trainee to really absorb the information being taught. On-the-job training thus becomes less a haphazard show-and-tell and more a real transfer of information. The goal of this document is to describe how to develop or manage an on-the-job training program so that information is passed on from trainer/coach to trainee efficiently and effectively. By efficient is meant the best use of time and resources of all those involved in the training process, and by effective is meant that the trainee truly learns the skills and internalizes the knowledge needed to perform the job well. The first part of the document discusses topics to think about when developing a formal on- the-job training program. A structure based on coaching is suggested. Then a workshop designed to prepare trainers as coaches is described. Workshop materials include an instructor’s guide and trainee workbook. These materials can be used to train coaches and to assist trainees as they go through the learning process. Content related to specific jobs can be added to these materials to create targeted on-the job-training manuals. Structuring a formal on-the-job training program It is likely that some form of on-the-job training (OJT) is being conducted at your workplace. The formality of that training can range from a structured program to an informal “follow Joe around” method. If your program is completely unstructured, it may not be meeting current training needs. Worse, it may perpetuate bad habits and create “trained” employees who are not given the same information or evaluated to the same standards. Wiehagen et al. comment that, “Success in using unplanned OJT is usually dependent on the luck of the draw, that is, whether the informal trainer is competent at the task he or she is teaching, is motivated to teach, can organize the job into logical components, and knows something about good practices in teaching and evaluating” (2002, p. 27). It is only through planning a structured OJT program that consistency can be created and maintained. At the least, all trainees who have successfully completed such a program can be expected to perform at an established level—they will know what they must do to be successful.

Jan 7, 2005

By V. A. Nieberlein

Problems of design involving the high-temperature characteristics of materials of construction have focused attention on tungsten, the metal with the highest melting point. To study the properties of this metal a method was needed to produce tungsten of high purity easily and consistently. The Bureau of Mines has made tungsten metal in massive form on a laboratory scale by hydrogen reduction of tungsten hexafluoride (WF6). Metal made in this manner had a purity of 99.99 percent or better, with reference to all detectable impurities, including gases. The process tolerated a wide variation in operating conditions, and the results with respect to total impurities as low as 0.01 percent were reproducible.

Jan 1, 1959

By H. A. Tucker

This Bureau of Mines investigation was conducted to determine the appropriate quantities of rare-earth methals (REM) in the form of silicides to add to an alloy steel for the purpose of increasing toughness and ductility. The work was conducted in a vacuum induction furnace with the rare-earth additions required to deoxidize and desulfurize a simulated basic oxygen furnace (BOF) vacuum-degassed steel initially containing 0.013 to 0.016 percent sulfur. The product proved to be as good or better than the best basic electric furnace steel of the same composition made by the steel industry. Twenty-three experimental heats of 5 Ni-Cr-Mo-V steel were made, cast into 50-1b ingots, and hot-worked in a press and a rolling mill to ½ inch plates which were then heat-treated to 130/150 ksi4 yield strength. Impact and tension tests showed that the addition of 0.025 to 0.100 percent, or ½ to 2 lb per ton, respectively, of rare-earth metals when compounded with silicon were appropriate for increasing toughness and ductility. These quantities resulted in retained cerium contents between 0.014 to 0.025 percent, and increased the Charpy V-notch energy absorption and the percent reduction of area significantly as compared with base heats at the same sulfur content levels. All the test heats, including those with additions of REH of as much as 4 lb/ton, had greater Charpy V-notch energy absorption values than the base composition could have developed at the starting sulfur range of 0.013-0.016 wt pct.

Jan 1, 1968

By R. E. Morgan, J. F. Barkley

"INTRODUCTION In city smoke-abatement work it is customary to require approval of the sizing of fuel-burning equipment. This is to insure that, with reasonable attention, the equipment can be operated essentially smokelessly, having such features as ample furnace volume and air supply. To answer the many inquiries that come to the Bureau of Mines as to what dimensions are acceptable and standard, the requirements of a number of smoke-abatement ordinances have been tabulated.CONCLUSIONSStudy of these tabulations shows that even after many years of fuel-burning practice and experience there is no common standard. Variations in the requirements for the same type of equipment under the same conditions of operation are great. This causes considerable difference in installation costs. Over-all costs being affected, the competitive positions of different types of fuel-burning equipment are also affected. It is apparent that there is a lack of information as to proper dimensions that is commonly accepted as authoritative.DISCUSSIONTable 1 gives the minimum furnace-setting heights required by various cities for mechanical underfeed stokers installed under H.R.T. boilers. Figure 1 shows a typical installation. The dimension given for each case is the distance from the dead plate of the stoker to bottom of boiler shell, unless otherwise noted. As shown in the table, different cities use different size-classification systems; it is not possible to make complete, exact, direct comparisons. Table la gives a comparison for various cities, showing the approximate percentage difference in H.R.T. furnace-setting heights required from those recommended by the Stoker Manufacturers' Association arbitrarily chosen to serve as a basis of comparison. The percentages are approxi¬mate because they were calculated as if all heights as given were measured from the dead plate of the stoker. In two cases a lower height is permitted, in a number of cases the height may be the same, and in a number of cases the height must be greater. The percentage increase goes to 100 in one case. Lack of uniformity is quite evident."

Mar 1, 1950

By G. S. McCaa

Rock-dusting is an. effective means of preventing coal-dust from propagating an explosion in a coal mine, but it will not prevent gas from igniting-explosively and with much attendant damage locally. Ventilation must therefore be effective at all times, regardless of the employment of other explosion-prevention methods, if gas explosions are to be avoided. This paper describes a gas explosion which occurred in as bituminous mine that was well rock-dusted at the point of ignition and which exemplifies the value of rock-dusting, the necessity of maintaining effective ventilation, and the need of permissible rock-dusting machines receiving power from a permissible locomotive. Description of Explosion The mine in which this explosion occurred is developed on a panel system in a practically level seam; the panel entries are driven in pairs, and the air current intakes on the right entry and returns on the left entry. Near the mouth of the intake a door is placed to control the ventilation; board stoppings are placed in crosscuts, except the second from the face, in which a brattice cloth curtain is hung, the last crosscut is left open and line brattices conduct the air current from the last crosscut to the faces. In No. 7 entry the last cross-cut was 152 feet from the face, the line brattice being within 38 feet of this face, and the second crosscut was 250 feet outby the face of the back entry or return. Seven days prior to the explosion the intake and return entries were rock-dusted to within 38 feet of the face, and as the entry had advanced during the week, the rock-dusting was to be extended.

Jan 1, 1929

In connection with tin strategic minerals investigations of the Bureau of Mines and the Geological Survey under authority of the Strategic Materials Act (Public 117, 76th Cong., 1st sess.) a study is being made of tin deposits in the United States in an effort to improve the situation with respect to domestic supplies. These studies include sampling and exploration of some of the larger deposits with the objective of establishing emergency reserves, if possible to do so. Two exploration projects have been completed, and the over-all results obtained are set forth in this progress report. RESOURCES Tin was first discovered on this continent in 100 in the Temescal Mountains of what is now southern California. In the ensuing century, occurrences of tin have been reported in no less than 17 States and Alaska. Although most of these are of scientific interest only, tin-bearing veins and placers in California, Alabama, North and South Carolina, Virginia, South Dakota, Wyoming, Texas, New Mexico, and Alaska have been extensively explored, and largo sums of money have been expended in recurring attempts to exploit them.

Jan 1, 1941

The results of a Feasibility and Design Study of Surface Impregnation Equipment to be used for Chemical Stabilization of Coal Mine Structures are described in this report. The study was sponsored by the United States Department of the Interior, Bureau of Mines, under Contract H0210055. This program was undertaken as an essential part of the Bureau of Mines Chemical Ground Stabilization Program. The responsible prime contractor was The Eimco Tunneling and Mining Machinery Division of the Envirotech Corporation. The Rocketdyne Division of the North American Rockwell Corporation performed part of the feasibility study and design and testing of the metering and feed system as a subcontractor to Eimco.

Jan 1, 1972

By Edward D. Thimons

The Bureau of Mines conducted in-mine tests to determine correction factors applicable to low-velocity airflows (below 150 fpm) measured by the smoke cloud, vane anemometer, and oil of wintergreen tracer gas techniques 0 The average correction factors found for these methods of measurement were lower than those reported in the literature for use with higher velocity measurements. All tests measured airflows with controlled average velocities ranging from 50 to 100 fpm. Correction factors averaged about 0.75 for readings taken by the centerline smoke cloud method, remotely controlled and stickheld center" line anemometer, and split traverse stick-held anemometer. For hand-held centerline anemometer and oil of wintergreen tracer gas readings, correction factors averaged about 0.67. Since special anemometers are needed to measure airflows in this low-velocity range, and since proper calibration of these anemometers is difficult and expensive, the use of anemometers for low-velocity measurement is imprac-tical. On the other hand, smoke and oil of wintergreen give results as con-sistent as those obtained with specially calibrated, low-velocity anemometers. Furthermore, they are easy to use and inexpensive.

Jan 1, 1979

By John M. Dower, Ralph W. Plummer, Terrence J. Stobbe, Hyunwook Kim

"The relationship between exposure to coal mine dust and the development of various respiratory diseases is well recognized. The cause of these diseases however. Is still uncertain. To study this cause-effect relationship, It Is necessary to characterize the coal mine dust In terms of the quantity of dust present and mineral content of the dust. Dust samples were collected using a Portable Continuous Aerosol Monitor (PCAM) and 4-stage cassette Impactors at various locations in an upper Freeport seam coal mine In West Virginia. The samples were analyzed using an X-ray microdiffraction film technique and energy dispersive scanning electron microscopy. This paper presents the results of the first phase of this characterization work which Includes determining the size distribution of the dust and the mineral content of the size intervals.IntroductionDiseases associated with dusts in coal mine environments continue to afflict miners in today's modem mines. These diseases still persist because, as Olishifski points out an employee rarely experiences exposures to a single environmental stress but rather to an Intricate Interplay of multiple stresses.(1) In the case of coal mining the multiple stresses are varying sizes of dust particles originating from coal imbedded minerals. Immediate roof strata bottom strata. Incombustible rock and the coal itself. The site of this Intricate Interplay Is the miner's lungs and the resulting diseases are a function of the composite dust exposures.The proper study of coal mine dust toxicity requires that the dusts used replicate existing coal and mineral dust compositions in their relevant size fractions. The purpose of this project is to develop the size and mineral content data necessary to support this ongoing toxicological effort.Existing coal mining standards and regulations also address total and respirable dust exposures. These dust terms refer to both the quality and quantity of the dust segment in the mine atmosphere. Dust quality addresses its coal and mineral content. whereas dust quantity Is described by mass per unit volume (mg/m3) The comprehensive characterization of coal mine dust exposures will enable revision of these standards and regulations to address the specific minerals and size fractions found to be toxic to human lung tissue."

Mar 1, 1989

By W. T. Millar

Graphite in the Suffern deposits near Hillburn, N. Y., consists of flakes ranging in size from fines to one-half inch in diameter. The Bureau of Mines investigated the Suffern deposits in the spring of 1943. Gneiss outcrops were examined, and five trenches excavated and sampled. The graphite is not confined to any definite zone but occurs in small, local pockets. Eleven samples were collected and combined for laboratory tests. Tests by the Bureau of Mines indicate that the graphite ore can be beneficiated by stage crushing, "skin flotation" of coarse flakes, and wet flotation of minus 10-mesh flakes. Over 90, percent of the graphite was recovered.

Jan 1, 1949

By L. C. IlsLey

Coal mining is more widely distributed throughout the United States than is generally known, as 30 States are credited with having coal mines. In 1919 twenty-three of these States each produced at least a million tons of bituminous coal, and all the States produced about 560,000,000 tons. In addition, Pennsylvania produced about 85,000,000 tons of anthracite. Twenty-eight States have regulations prepared by commissions or have enacted laws governing the operation of coal mines. Pennsyl¬vania has separate codes for the anthracite and bituminous fields. The codes may be classified as follows: Twelve distinctly coal¬mining codes; eight codes that are essentially coal mining, but also apply to other mines; five codes that are subdivided, referring partly to coal mines and partly to other mines; and four codes that are essentially metal mining, but apply in part or in whole to coal mining. The first State to have a coal-mining law was Pennsylvania, which enacted a law, for Schuylkill County only, in 1869. The first State to enact a coal-mining law governing all the coal mines in the State was Illinois in 1872, followed by Ohio in 1873. Pennsylvania in 1879 enacted a law for anthracite mines only, but did not enact similar laws for bituminous mines until 1577. At least 10 other States enacted coal-mining laws between the years 1870 and 1890. Before 1890 electricity was little used in coal-ruining operations and therefore practically no provisions governing the installation, inspection, or maintenance of electrical equipment were made in any of the laws enacted up to 1890. In the law of Colorado, approved April 8, 1885, there is a reference to the use of telephones, probably the first reference to electrical equipment of any kind in a State-mining code. Most of the mining codes have been changed from their original form by amendment or by complete revision. In some of the early changes a casual reference is made to the use of electricity or to the handling of electrical equipment. In 1911 Pennsylvania added

Jan 1, 1920

By J. Roger Loebenstein

Demand for arsenic trioxide exceeded supply in 1978 and 1979, and the major domestic and foreign producers allocated available supplies to customers. Major demand has been from the cotton-growing and wood-preserving industries. Ample supplies of arsenic metal produced in the United States and Sweden were available in 1978 and 1979. Major demand for metal was from the automobile battery industry in Japan, Europe, and the United States. Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA), promulgated the final standard on the occupational exposure to inorganic arsenic, effective August 1, 1978.2 The need for the standard was a result of OSHA's conclusion that inorganic arsenic is a human carcinogen. The purpose of the standard was to minimize the incidence of lung cancer among workers exposed to inorganic arsenic. The maximum exposure to arsenic was lowered from the previous ceiling of 500 micrograms per cubic meter of air to 10 micrograms per cubic meter over an 8-hour time period. OSHA had originally recommended a ceiling limit of 4 micrograms per cubic meter in January 1975. Provisions of the new standard require exposed employees to wear respirators and undergo continuous medical monitoring. Other provisions establish regulated areas limited to authorized employees and require the construction of special lunch-room and worker hygiene facilities and the posting of signs and labels warning of the presence of arsenic. The new arsenic standard will have a significant economic impact on copper, zinc, gold, and lead smelters as well as consumers of arsenic trioxide. A number of copper companies have joined together to contest the standard in court. However, measures to comply with the standard have been initiated by ASARCO Incorporated at its Tacoma, Wash. plant.

Jan 1, 1980

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a mini-computer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns an echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display discs, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 10, 1980