Search Documents

By E. L. Litchfield

This report of work by the Federal Bureau of Mines has two primary objectives: A survey of the present status and usefulness of the minimum ignition-energy concept, and the presentation of recent data that are believed to bear on the safety problem associated with the ignition of combustible gases by electric discharges. The minimum ignition-energy concept has widespread applicability, especially to safety. The primary obstacle in making theoretical calculations of the requisite ignition energy is the lack of data on chemical kinetics and flame hydrodynamics. The new data on electrical ignition are representative of the great increase in knowledge that can be achieved by proper utilization of geometrical and electrical characteristics associated with the ignition source. CONCEPT OF MINIMUM IGNITION ENERGY The basic concept of a minimum ignition energy (the minimum amount of energy required to cause ignition) follows quite naturally from general physical principles and from the stability (lack of chemical reaction) of the gaseous mixture under the initial conditions. It also follows that if, as a first condition, lossless, instantaneous, and spatially localized energy can be injected and, as a second condition, the relaxation time for conversion of this type of energy to the type required for the reaction is short compared to some characteristic time scale of the ignition phenomenon, the energy requirements will be essentially independent of the type of energy source. Even if condition one cannot be fulfilled, it is sometimes possible to estimate the energy content of the gas required for ignition, and under these circumstances, condition one is fulfilled in effect. There are several instances where results can be interpreted for circumstances that effectively satisfy conditions one and two; these will be discussed later.

Jan 1, 1960

[ ]

Jan 1, 2011

By James L. Hendrix

A study was made of the United States Bureau of Mines' chlorine-oxygen leaching process for complex sulfide concentrates. The investigation sought to determine the kinetic order and IT mechanisms involved in the reactions betweens sphalerite, and galena with chlorine. The influence of copper on the extraction rates was also studied. It has been shown the rates of reaction of chlorine in aqueous solutions with sphalerite and galena are both zero order at 373K with the rate limiting step being the chemical reaction. Addition of cupric chloride increased the extractions of both lead and zinc.

Jan 1, 1980

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964

By G. S. Scott, G. W. Jones

"INTRODUCTION In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, a. control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration.Many of the anthracite fires have been active for years and have progressed considerable distances free their original source.Some of the fires are in inaccessible territory, and it is often impossible to determine with any degree of accuracy their exact location or even the veins of coal that are afire, especially when the fire is in the upper strata and when it is impossible to go underground because of flooded conditions or the presence of an irrespirable atmosphere.In such cases, the only means by which the trend of a fire may be ascertained (as a result of any fire-fighting methods that may have been employed) are the sampling, exanination, and interpretation of the gaseous products coming from the fire area. The most important information desired is to know whether the temperature in the heated area is increasing or decreasing and to determine whether a fire that has been sealed is cooling down to normal mine temperatures or is maintaining its heat or is increasing in intensity due to infiltration of outside air.Interpretation of the analyses of gaseous products from refuse banks on the surface also should be of value in combating such fires. Refuse bank fires, with the additional danger of starting an underground fire through ignition of the outcrop, are by no means unknown in the anthracite coal region, and the causes of such fires are not always apparent. In a few cases the causes have been strongly suggestive of spontaneous origin."

Jun 1, 1938

By R. D. Leitch

Beside many other damaging effects of acid mine drainage, corrosion of pipe lines and pumps frequently adds much to mine operating costs. Not only is it often necessary to install special and relatively costly acid-resistant materials, but even these may require frequent replacements. It is not unusual for ordinary steel pipe to last only a few days in some highly acid waters, while other common materials, though more resistant, frequently last only a few weeks. In the spring of 1935, local PWA authorities offered to assign a number of persons to various problems under the direction of regular employees of the Bureau of Mines. It was believed that at least some simple tests on as many different kinds of acid-resistant pipes as could readily be obtained might produce interesting and valuable information for the mining industry. This paper describes the tests and some results that have since been noted.

Jan 1, 1938

By C. Melvin Lepper

A solid-state amplifier for the bridge circuit of an atomic-absorption mercury detector is presented and described. Operational advantages over previously used circuitry include improved time and temperature stability, increased measurement accuracy, and simplified setup, calibration, and operation.

Jan 1, 1972

By L. G. Marsh

The manufacture of lubricating oils from wax-bearing crude petroleums involves the removal and recovery of the paraffin wax contained in the lubricating distillates. During this process several intermediate products are formed, among them the mixture of waxes and oils known to the refiners as "foots oil." Because of its complex character, foots oil is little understood, and therefore methods of handling it in refineries are often inefficient. The Bureau of Mines is studying the manufacture of lubricating oils, and during the work has investigated the redistillation of foots oil. This report gives in brief the results of the investigation, and recommendations based upon it.

Jan 1, 1926

By Norwood B. Melcher

This report describes preliminary experiments by the Federal Bureau of Mines on the practicability of adding raw pellets of taconite concentrate to blast furnace feeds. The usual industrial practice is to harden the pellets by heating before they are charged to the furnace. The Bureau research demonstrated that raw pellets could be successfully smelted in an experimental furnace with no significant change in coke consumption and only a moderate increase in dust losses. The dust loss was 43 pounds per ton of metal for an all-pellet charge, compared with 7 pounds per ton for an all-sinter charge. Raw taconite pellets undergo only slight degradation during charging to the furnace if 1 percent bentonite is used as a binder. INTRODUCTION Fines and concentrates must be consolidated or agglomerated into larger masses before they can be smelted in a commercial blast furnace. Such agglomeration is usually done by sintering, pelletizing, nodulizing, or briquetting. Sintering has been the more common practice, but with the advent of taconite concentrates pelletizing is increasing in importance.

Jan 1, 1960

By Robert L. Marovelli

The thermal conductivities of six rocks were measured by the transient line source method over the temperature range of -850 to 1,500° F. Close-fitting ceramic probes were used in 0.065-inch-diameter holes drilled through 5-to 6-inch-thick rock specimens. Taconite, granite, quartzite, and basalt were used in the tests. The method yields absolute data and is applicable to both laboratory and in situ measurements.

Jan 1, 1965

By W. O. Philbrook

Reduced-scale models have long been used in hydrodynamics, aerodynamics, and heat transfer for studying fundamental flow relations or the performance of prototype designs under prescribed conditions. The pilot plant is a common tool of chemical engineering for investigating process variables and as an integral step in developing a new process. The metallurgical industry was rather slow to recognize the applicability of these techniques to some of its established and rather complex processes, but there has been a rapidly increasing number of applications of the principles of modeling in process metallurgy since World War II. Not only have pilot-scale operations been employed for developing methods of extracting metals that have recently achieved commercial importance, as well as new processes for some of the commoner metals, but models have also been used for engineering studies aimed at better understanding of the controlling, variables of time-honored conventional processes, It appears that the principles of similitude have become accepted as a useful tool, when properly applied, in metallurgy as in other fields of engineering. Much of the work of the Pyrometallurgical Laboratory, Region V, involves study of high-temperature smelting and refining processes for ferrous and related metals in pilot-scale equipment, such as the experimental blast furnace, converter, open-hearth, arc furnace, and rotary kiln. It was appropriate for the work of this laboratory that guiding principles for designing apparatus and interpreting results should be set down and that a bibliography of related work should be available for reference. A summary of the principles of model study and a brief review of some of the more noteworthy general papers have been published elsewhere.3/ Also, the Bureau of mines plans to publish a report of investigations describing its experimental work in this field. The bibliography is presented here as a service to others who may have use for it.

Jan 1, 1958

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency in low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas. The results have been summarized in terms of maximum communication range expected per seam and noise condition. Scatter gain is further explored as a simple measure of energy coupled to conductors.

Jan 6, 1978

By Robert D. Schmidt

This Bureau of Mines report describes the development and application of a computer model for simulating the hydrological activity associated with in situ leaching. The model is intended to provide uranium resource developers with a description of the flow behavior of leachants and ground water during the development, production, and restoration phases of a leaching operation involving an arbitrary pattern of injection and recovery wells. Different aquifer environments are modeled, using a closed-form solution to the partial differential equation that describes three-dimensional changes in piezometric head as a result of pumping from leachant injection and recovery wells. The computer program can model a maximum of, 50 arbitarily located wells. Numerical techniques involving difference quotients and Taylor expansions about time points are used to derive time, velocity, areal sweep, and fluid volume parameters associated with leaching hydraulics. These parameters are output by the program in graphic and tabular formats. Other numeric methods insure that the program running time is minimized without significantly affect-ing the accuracy of results.

Jan 1, 1980

By Aarne Visnapuu

Experimental modifications have been made by the Bureau of Mines on standard pneumatic rock drills to reduce the noise of the air exhaust, drill steel resonance noise, and noise radiated by the drill body. A close-fitting case and muffler around the drill body, consisting of a metallic honeycomb skeleton filled with viscoelastic absorber on the inside and a durable outer shell, provide both exhaust and drill body noise muffling and absorption. Drill steel resonance noise is reduced by a constrained-layer treatment consisting of a tubular metal cover bonded to the ouside of the rod by a viscoelastic filler. Damping alloy components have been developed to reduce metallic resonance noise. Combined, these modifications have reduced the drilling noise level in granite from 115 dbA to 97 dbA. Data are presented on the individual and combined effects of these modifications on drilling noise and performance.

Jan 1, 1975

By F. W. Wood

Ingots of zirconium and other highly reactive metals such as titanium and hafnium produced by the consumable-electrode arc-melting process require conditioning before forging or rolling. A nondestructive, arc-conditioning technique has been developed as a substitute for lathe conditioning. The technique employs en electric arc under an inert atmosphere to fuse surface metal on the sidewalls of ingots without seriously affecting the general quality of the ingots. Advantages of the practice are Increased yields, lower accumulation of inferior scrap, and actual cost savings. The work cited in this report was done on zirconium. INTRODUCTION The consumable-electrode arc-melting process as practiced at the Bureau of Mines3 4/ has proved to be a technique for producing sound, homogeneous, commercial-size ingots of zirconium and its alloys. Ingots produced by this process, however, have as a characteristic a layer of partly fused metal on the sidewall to a depth of 3/16 to 3/8 inch. To prevent extension of surface imperfections during forging, the ingots are ordinarily conditioned by removing defective material in a lathe. If the metal were less reactive or the requirements less severe, the machine chips could be recycled and remelted. However, zirconium, being so oxygen sensitive, is contaminated by merely being machined despite extensive cooling of the tool bit. Further, being contaminated with oxygen, the chip metal upon remelting is 10 to 25 Brinell-hardnese numbers harder than the ingot from which it was machined. For this reason, the ingot specifications for naval reactor use have prohibited remelting machine chips, except as required for starting pads. Again, were zirconium less costly or less in demand this ever-increasing pile could be burned to oxide and recycled through the Kroll sponge process. Economics do not favor this, as melting feed stock has an estimated increase In value over oxide of about $8.80 per pound of contained zirconium. The efforts of the Bureau to solve the problem have been directed along two lines: To reduce the contamination of the machine chips produced and to reduce the quantity of the chips produced. This paper presents the technique developed to reduce the quantity of chips produced by arc-conditioning the remelted ingot.

Jan 1, 1955

[ ]

Jan 1, 2011

By H. H. Fields, Stephen Krickovic, M. G. Zabetakis, Albert Sainato

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot -deep vertical borehole. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the corresponding values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

By Edward L. McHugh

Mineral resources in the Silver Creek study area of the Nez Perce National Forest. Idaho, were investigated during the summer Of 1989. The study area includes the 36,100-acre Silver Creek-Pilot Knob RARE II area (No. 1-849) on the north side of the South Fork Clearwater River, about 11 miles west of Elk City, 10. Mines in and near the study area in the Tenmile and Newsome mining districts produced about 100.000 02 of gold, mostly from placers. Gold production had an historic value estimated at 52 million, equivalent to nearly $40 million at today's prices. Lode mines produced about 19,000 oz of gold, along with smaller amounts of silver, copper, lead, and zinc. Of 34 mines and prospects examined, ten lode properties are considered to be significant by virtue of their past development or production and the presence of possibly ore-grade mineralization. There are no identified mineral resources in the study area; however, samples that contained gold and anomalous arsenic delineate a three-mile-long area from the Sentinel mine, north to the Blue Quartz prospect where exploration might disclose resources. One mining company is conducting geophysical studies and drilling within the delineated area. In addition, six placer sites may contain enough gold to be of possible interest for future exploration and development.

Jan 1, 1991

By John P. Gooch

The Bureau of Mines wrote a computer program which calculates the saturation curves and condensation characteristics of gaseous mixtures consisting of binary organic vapor and air. The program employs an algorithm which assumes an equilibrium mechanism for condensation, and the degree of fractionation obtained is predicted on the basis of relative volatility. The program incorporates a feature which allows the user to examine the fractionation resulting from condensation as a function of the size of the temperature increments over which condensation is assumed to occur. If a single. temperature interval between the dewpoint of the mixture and the outlet temperature of the condenser is assumed for the calculation, the results obtained will be those resulting from a single equilibrium condensation. If the condensation is assumed to occur over a number of temperature increments, the results obtained will approach those predicted by the Rayleigh equation as the magnitude of the temperature increments approaches zero. The results from calculations performed on vapor mixtures from organic heavy liquid solutions used in beneficiating potash and brucite ores are presented. The liquids are solutions of dibromomethane in trichloroethylene or perchloroethylene. The results show the degree of liquid recovery which is possible by cooling mixtures of organic vapor in air. Compositions of the vapor range from 10 to 95 percent air, and assumed condenser exit temperatures range from 110° to 50° F.

Jan 1, 1971

By T. N. McVay

The Bureau of Mines has developed a field test for detecting the presence of columbium in a variety of minerals containing the clement. The test consists of fusing the mineral or rock powder with potassium pyrosulfate in a porcelain crucible, digesting the melt with hot dilute hydrochloric acid to release the columbium oxide (Cb205), and subsequently reducing the columbium oxide to a lower oxide by adding tin, which gives a blue color to the contents of the crucible. The method will detect 1 percent of contained columbium oxide (Cb205) in a mineral sample provided no tungsten is present. If a mineral containing appreciable titanium is test,-!d in the same manner, the solution in the crucible becomes violet. In the presence of columbium, titanium at first causes a violet coloration of the solution, which after a few minutes is masked by the stronger blue of the reduced columbium oxide. Although tantalum oxide (Ta205) does not interfere with the columbium test, tungsten gives a blue color that is indistinguishable from the color obtained with columbium. A simple method is available to detect the presence of columbium in the absence of tungsten, but when the presence of tungsten is suspected, the sample must be subjected to somewhat more elaborate chemical tests to determine the presence or absence of columbium. Although these latter tests can be made in the field, several steps are involved that arc best performed in the laboratory with simple equipment.

Jan 1, 1962