Search Documents

NIOSH recommends that exposures to respirable coal mine dust be limited to 1 mg/m3 as a TWA concentration for up to 10 hr/day during a 40-hr workweek, measured according to current MSHA methods (see Section 5.1 and Appendix J). NIOSH recommends that sampling be conducted with a device that operates in accordance with the NIOSH accuracy criteria [Busch 1977; Busch and Taylor 198 11 and the international definition of respirable dust [ACGIH 1994; CEN 1993; IS01993; Soderholm 1991a,b; 1989].* The REL represents the upper limit of exposure for each worker during each work shift. For single, full-shift samples used to determine noncompliance, NIOSH recommends that MSHA make no upward adjustment of the REL to account for measurement uncertainties [NIOSH 1994c] (see also Section 5.6.2). NIOSH further recommends that all reasonable efforts be made to reduce exposures to respirable coal mine dust below the REL through the use of engineering controls and work practices.

Jan 1, 1997

Improve the effectiveness of face ventilation systems in coal mines by minimizing leakage around line and check curtains. Approach In-mine surveys were conducted to determine current curtain construction techniques, their effectiveness and associated costs. In addition, performance characteristics of extensible curtains were evaluated. A total of 77 conventional curtains in 10 mines was examined for 12 important characteristics. Extensible curtains were erected in a full-scale model and examined for operational difficulties, effects of leakage, and air pressure. Survey Results The underground mine study identified four categories of face brattice construction ranging from simple to complex: 1. Simple suspension of the curtain from roof bolts with the bottom edge lying on floor. 2. Spadding of the curtain to the roof on about 12-inch centers and stabilization of the bottom edge with wood or rock. 3. Use of vertical props and spads with a base board for support on the bottom. 4. Use of vertical props with caps and bottom boards plus horizontal brattice support boards.

Jan 1, 1984

By Suzann C. Ambrosio

Crude petroleum, the only commercially exploited mineral resource in Cameroon, continued to dominate developments in the mineral industry sector. International mining concerns have expressed interest in developing Cameroon's bauxite and iron and steel potentials. Domestically, the mineral industry focused on production of fertilisers for agricultural development, infrastructure construction, and hydrocarbon development, through the nearly self-sufficient production of fertilizer materials, cement, and crude oil. The mineral sector contributed 5.6% to the estimated 1981 gross domestic product (GDP) of $6.5 billion.2 Petroleum exports accounted for approximately 4.5% of the 1981 GDP and exceeded coffee and cocoa exports for the second consecutive year. The trade gap widened during the fiscal year ending on July 80, 1981, owing to a 21% increase in exports and a 25% increase in imports. Offsetting these balance-of-payments difficulties, typical of developing countries' early economic stages, were increases in foreign exchange reserves to $71 trillion by May 1983.

Jan 1, 1983

By Charles L. Kimbell

Available statistics on 1989 worldwide consumption of selected nonfuel minerals shown in table 5 show increases for 11 of 14 listed nonfuel mineral commodities with 1 unchanged from the 1988 level, a departure from the pattern of the past 2 years, in which each of the listed commodities registered gains. The 1989 results, however, were better than those for 1986 when only seven listed nonfuel mineral commodities recorded gains with one un- changed from 1985. Consumption of the two ferrous metal raw materials listed advanced as functions of increased output of pig iron and crude steel. The increase in iron ore consumption exceeded the increase in iron ore output, suggesting a slight drawdown of world iron ore inventories. The estimated in- crease in iron and steel scrap consumption was slightly greater than the minuscule increase in world steel production, but it is believed that there was little change in the ratio of iron ore to scrap in steel plant feed on a global basis.

Jan 1, 1992

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983

By D. H. Chambers

Digestion studies were undertaken to develop a method for the rapid dissolution of high-temperature ferroalloy scrap. Laboratory tests showed: (1) dissolution of alloy scrap with ferric ion as the leaching agent was a moderately rapid method of digestion; (2) the dissolution process can be considered as a typical reaction of a metal with chlorine gas, although evidence was obtained to show dissolution as a two-step process, one step as the reduction of ferric ion by the soluble alloy constituents and the other as the oxidation of ferrous ion with chlorine gas; and (3) the attack of ferric ion on the alloy was a function of alloy composition, ferric to ferrous ion ratio, and area of contact between leach solution and alloy. The exceedingly complex nature of alloy compositions and dissolution products generally precluded satisfactory analytical determinations. Results of moderate accuracy were obtained using complex modifications of standard analytical and spectrographic techniques.

Jan 1, 1968

Provide respiratory protection for escape in a toxic or oxygen-deficient atmosphere with a device small and light enough to be belt-worn. Approach Combine a 10-minute, belt-worn respirator with a stored, larger, long-duration (60-minute) attachment that can be plugged into the 10-minute unit without removing the mouthpiece. How It Works The 10-minute device will be carried by the miner at all times, and the 60-minute canister or attachment will be stored near the miner. In the event of a disaster, the 10-minute device would be donned immediately. The miner would then proceed to the stored 60-minute unit and plug it into the 10-minute unit. For the 10-minute unit, a breathing circuit was developed in which air is passed through the KO2 bed twice per respiration. The 60-minute canister differs from the 10-minute unit in that air is drawn only once through the chemical bed per respira-

Jan 1, 1981

By Ben A. Kornhauser

Petroleum production was the principal component of the mineral industry, followed by cement production and some salt output. The French Central Fund for Economics Cooperation loaned $9.15 million2 to the Communauté Electrique du Benin (CEB), which served Benin and Togo, toward financing the construction of a dam on the Mono River at Nangbeto, Togo. The dam was to supply hydroelectric power to reduce the energy dependence of the two countries and to irrigate crops. Nine other international financial organizations, including the International Bank for Reconstruction and Development (World Bank). the African Development Bank, the Arab Bank for African Economic Development, and the French Aid and Cooperation Fund, contributed to the estimated $140 million cost of the dam. The CEB also was to contribute to the financing. Contracts amounting to $60 million already had been awarded to West German and Canadian firms. The dam was expected to be completed in 1987.

Jan 1, 1986

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1962. Injury experience is measured by the number of injuries sustained per million man-hours of exposure in each industry. No attempt has been made to combine these data and present rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in volume III of the Minerals Yearbook. COAL The injury-frequency rate for the coal-mining industry of the United States increased less than 2 percent, according to reports received by the Bureau of Mines. The number of fatal and nonfatal injuries per million man-hours in 1962 was 45.86, based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1963

Lower costs associated with hands-on training in donning and using a CSE ,self-contained self-rescuer (SCSR). Background In June 1987, the Mine Safety and Heath Administration (MSHA) issued an Emergency Temporary Standard (ETS) requiring that all persons entering underground coal mines must be given bands-on SCSR training. The ETS will shortly be replaced by a new standard requiring this hands-on training. Bureau of Mines research has shown that the most effective means of delivering this training is to have the trainee go through a six-step training procedure while in a kneeling position. Once the miner has looped the neckstrap over his or her head, he or she completes the donning sequence in this order: 1) activate oxygen; 2) insert mouthpiece; 3) put on nose clips; 4) put on goggles; 5) adjust neck and waist straps; and 6) replace miner's cap and prepare to move out. This procedure is repeated until the miner demonstrates that he or she is proficient at the task.

Jan 1, 1988

By M. M. Tilman

The Bureau of Mines investigated the precipitation strengthening of lead¬-base alloys containing 0.5 through 4 weight-percent combined Cd plus Sb. The Cd and Sb were alloyed in a 1-to-1 atomic ratio which maintained compositions along the quasi-binary section Pb-CdSb. Tensile properties, creep rates, and stress-rupture values were obtained on alloys in the aged condition. The highest tensile strength was observed in an alloy of Pb-3 CdSb, After aging for 6 months at 90°±3° F, this alloy had a mean tensile strength of 8,950 psi with 15-percent elongation. An aged alloy of Pb-1 CdSb exhibited a steady state creep rate of 1.2 X 10-3 percent per day at a stress of 500 psi and a temperature of 90°±3° F. Times to rupture at stresses up to 4,000 psi and at a temperature of 90°±3° F were obtained for some compositions.

Jan 1, 1970

By Nancy S. Raymon

The Bureau of Mines investigated the effect of controlled additions of selected metal oxides, as well as the adjustment of the calcia-to-silica ratio on the high-temperature strength of refractory-grade periclase. Increases in the hot flexural strength of some periclase materials in the range of threefold to fourfold were obtained with additions of Zr02 and by adjustment of the CaO:Si02 ratio to the 2.5 to 3.0 level. Results show that for each periclase refractory raw material, there exists a combination of level of Zr02 addition and an adjustment to the CaO:Si02 ratio that optimizes the hot flexural strength of each of these materials. Data also indicate that the improved hot strengths can be attributed to the high-temperature secondary phases formed between the different levels of periclase impurities and the additives, resulting in improved intergranular high-temperature bond strength.

Jan 1, 1982

Reduce the dust exposure to the operator of a longwall shearer with a novel foam spray system. Approach Discharge foam through the nozzles of a shearer drum so that foam and coal are better mixed. How It Works Bureau of Mines research showed that two very important principles for successful application of foam are: (1) moisture distribution and (2) degree of mixing. Foam can distribute a given quantity of moisture much more evenly over a large surface area. Successful Bureau tests of foam for dust control always involve a high degree of mixing between the foam and the material, Mixing, permits a greater distribution of foam throughout the mined product. The most suitable location of foam application would be at the point where the dust is generated, before the dust becomes airborne. Foam nozzles located in the cutter drum (pick face foaming or ejecting foam through scroll sprays) will suppress dust close to its source.

Jan 1, 1989

By George S. Koch

A statistical analysis of silver assay data from rotary-drill-hole cut-tings and diamond-drill-hole cores from the Round Mountain prospect, Custer County, Colo., demonstrates several useful methods for estimating grades and tonnages of ore from the drilling of wide-spaced holes in disseminated deposits of precious metals. A new method of are appraisal is introduced which estimates grade and tonnage of are by calculating convex hulls (smallest convex polygons) for sample points with assay values above specified cutoff grades. Analyses of variance compare the consistency of data from rotary-and diamond-drill holes, from rotary-drill holes sampled at 2-and 4-foot intervals, from two methods of sample preparation, and from atomic-absorption and fire assaying. Evidently, data from the two types of drill holes, from holes sampled at the two intervals, and from different methods of preparation are in agreement. Atomic-absorption silver values are consistently lower than fire-assay silver values.

Jan 1, 1971

By H. E. Powell

The mineral dressing research here reported is part of a continuing program by the Bureau of Mines to develop new or improved concentration processes for oxidized or partly oxidized lead and zinc ores. A sample of low-grade sulfide-oxide, lead-zinc ore from Jasper County, Mo., containing galena, cerussite, pyromorphite, hemimorphite, smithsonite, and sphalerite was concentrated by froth flotation and tabling to a grade of 66 percent lead. Because of the presence of a high content of slime-size values, the overall recovery of lead was limited to 64 percent at this grade. Tests to recover the zinc by froth flotation and by gravity concentration did not give satisfactory results. INTRODUCTION Since its establishment, the Rolla Metallurgy Research Center has con-ducted studies of base metals as a part of its overall program (1, 2, 3, 4, 5,6,7).3/ This research has been, and is, directed to beneficiating complex and submarginal ores, to retreating rejects from commercial installations, and to developing fundamental data.

Jan 1, 1960

By E. O. Binyon

The Blue Metal corundum-andalusite deposit, in the Buckskin Mining district, Douglas County, Nev., was explored by the Bureau of Mines in 1945. The results of that work were presented in Report of Investigations 3895, exploration of the Blue Metal Corundum Property, Douglas County, Nev. published in August 1946. That report also describes the property in detail, giving location, ownership, history, geology, and data on beneficiation tests. Further exploration was carried on in April and Way 1947, the results of which are presented in this report. The work consisted of 175 feet of drift and crosscut, bringing the total to 398 feet of underground working, as shown in figures 1 and 2. The 23-foot drift, which was the last work of the initial project, was extended 99 feet northward along the shear zone, and three crosscuts, spaced at approximately equal intervals along the drift, were driven to country rock on the hanging and foot walls of the zone.

Jan 1, 1948

By Oliver C. Ralston

OUTSTANDING TRENDS of the year included the following: 1. Concentration and beneficiation of iron ores to provide improved blast-furnace feed and extend ore reserves. 2. Successful development of pelletizing and sintering procedures for fine iron ores. 3. The realization that cyclone separation could replace existing classifiers in many grinding circuits. 4. The rapidly blossoming metallurgy of ultrapure silicon and improvements in zone melting. 5. The rapid increase in the use of liquid-liquid extraction and ion exchange in hydrometallurgy. 6. The industrial application of vacuum melting on the 100-ton scale. 7. The hope for developing a columbium (noibium) base alloy for high-temperature use. The technologic advancement in metallurgy that had the greatest effect on the American economy was the beneficiation of iron ores to give improved feed for blast furnaces and indirectly extend our ore reserves. This was not a sudden development but rather culmination of a decade of intensive effort.

Jan 1, 1958

By James Westfield, S H. Ash

Because of the increasing shortage of fuel in the United States, especially of residential fuel in the Eastern and New England States, it was essential that the maximum production of anthracite be obtained to help win the war and to prevent human distress. The nine railroads that depend on the anthracite region for a substantial portion of their business were not congested unduly with other traffic, because the region was not participating in industrial activities to the same degree as in many other sections of the United States; consequently, transportation of anthracite to the New England States, New York, New Jersey, and eastern Pennsylvania over a shorter rail haul than for any other fuel was desirable. The prevention of floods that would cause a loss of anthracite production was important to the war program. Every shutdown deprives the northeastern section of the United States of anthracite that is needed badly. Failure to prevent inundation of anthracite mines halts production, endangers the lives of workmen, damages, sometimes beyond repair, vital underground equipment, and threatens the permanent loss of a large portion of the Nation’s anthracite reserves. Funds were made available to the Department of the Interior, Bureau of Mines, for the fiscal year ended June 30, 1945, through a supplemental appropriation for anthracite investigations, one of which was to conduct inquiries and scientific and technologic investigations that have a bearing on the anthracite mine-flood problem. As part of the investigation, the Bureau proposed to obtain the cooperation of the anthracite-mining companies and the State in effecting a program to prevent the inundation of mines in the anthracite region. No large engineering projects were undertaken by the Bureau during the fiscal year ended June 30, 1945, on the anthracite mine-flood problem. Small projects were chosen that could be completed within 1 year to prevent loss of anthracite production at a critical time. It was believed that such projects would lessen the chance that flood water would inundate active mine workings.

Mar 1, 1946

To produce industrial-grade titanium castings by processes that are nonpolluting and lower cost than the currently used rammed-graphite process. Approach Foundry-grade zircon and olivine sands, bonded by waterglass or bentonite, are used to make shell or rammed molds which require relatively low-drying temperatures and do not generate noxious fumes during drying or casting. Procedures Three separate processes have been developed which meet the stated pollution and cost goals. These are: 1. Waterglass-bonded rammed zircon or olivine sand molds are dried at 480°F, zirconia washed, redried, and used in an inductoslag or skull-casting furnace. 2. Waterglass-bonded zircon or olivine sand shell molds are formed at 560°F, cured at 620°F, zirconia washed, dried at 480°F. and used in an inductoslag furnace. 3. Rammed zircon and olivine sand molds are bonded with western bentonite, zirconia washed, dried at 980°F, and used in an inductoslag or skull-casting furnace.

Jan 1, 1981

By S. J. Pearce

The Bureau of Mines has prepared, as circumstances have dictated, a series of Schedules setting forth the minimum requirements that various types of equipment should meet to be considered safe and satisfactory for use in certain hazardous or unhealthful conditions. These Schedules cover a wide variety of devices ranging from explosives to electrically operated mine locomotives. This paper deals with those Bureau of Mines Schedules under which respiratory protective devices are tested and approved, and its purpose is to explain the function and operation of these Schedules. Provisions have been made for testing and approval of the following types of respiratory protective devices: Self-contained breathing apparatus,2/ supplied-air respirators,3/ gas masks,4/ dispersoid respirators,5/ and chemical cartridge respirators.6 These devices are tested at the Central Experiment Station of the Bureau of Mines in Pittsburgh, Pa. Self-contained breathing apparatus is tested by the Safety Branch, and the other types of respirators are tested by the Health Branch.

Jan 1, 1951