Search Documents

By F. M. Goodwin, Campbell. John, W. J. Hiffs, G. W. Jones

"INTRODUCTION In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co. a survey has been conducted continuously since 1929 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933.Yearly reports 6 giving the results obtained since the start of the survey have been published.The method and procedure of conductin, the survey in 1935 were the same as heretofore.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of F. D. Comerford, president of the Edison Electric Illuminating Co. of Boston; E. N. Farnesworth, Jr., vice president and general manager of the Boston Consolidated Gas Co.; and A. C. Fieldner chief engineer, Experiment Stations Division, U. S. Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department, of the Edison Electric Illuminating Co., cooperated in furnishing men and information for the work,"

Oct 1, 1936

By Bill M. Stewart

The Bureau of Mines conducted laboratory tests to determine the effects on the physical properties of coarse coal waste of adding large amounts of fine coal waste. Maximum laboratory dry density, optimum moisture content, shear strength, and permeability tests were conducted on samples that contained 18 to 60 pct minus No.4 (U.S. Standard sieve size) coal waste. For the nonslaky materials, maximum laboratory densities were highest and permeabilities lowest when the samples contained between 30 and 40 pct minus No.4. Shear strength increased rapidly when the proportion of minus No. 4 was increased from 20 to 40 pct, but then increased only slightly or leveled off when the minus No. 4 was increased to 60 pct. Optimum moisture content and permeability were the physical properties most affected by the addition of fines. Optimum moisture content increased as much as 3 pct, and permeabilities decreased up to three orders of magnitude. Slaky coal waste material had physical property reactions to the addition of fines substantially different from those of nonslaky material.

Jan 1, 1981

By James W. Townsend, William H. King

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Alisman, chief, Salt Lake City Division, Mining Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon ore such technique.The Wright borehole-surveying instrument developed at the Homestake mine, Lead, S. Dak., has been described in several publications. 3/ For the benefit of those to whom the publications are not available, the instrument is described here. However, this article will be concerned mainly with the technique developed by the Federal Bureau of Mines for using the instrument.In the use of the Wright borehole-surveying instrument, it was found advantageous to develop a standard practice of operation covering type of film, preparation and care of film, loading film in instrument, placing instrument in container, exposure time, unloading film from instrument, development of film, and determination of dip and strike from film impressions."

May 1, 1947

By Joseph C. Zelanko, Anthony T. Iannacchione

One of the most difficult, longstanding engineering problems associated with coal mining is the catastrophic failure of cog mine structures known as bumps. For more than 70 years, researchers and practitioners have assembled a wealth of technical information on coal bumps in an attempt to understand and control them. However, many technical issues raised long ago are still being debated today. This paper examines past experiences and recognizes achievements in the realm of coal bumps. U.S. Bureau of Mines (USBM) researchers collected and analyzed 172 coal bump incident reports and compiled the pertinent statistics into a database. Actual field studied are also discussed. Examination of past experience has shown that there is no one set of defining characteristics that is responsible for coal bumps. In all cases, bumps occur when complex arrangements of geology, stress, and mining conditions interact to interfere with the orderly dissipation of stress. However, it is evident from the database that a tremendous reservoir of knowledge has been established from past experience that has unquestionably limited the severity of coal mine bumps in the United States.

By A. C. Fieldner

The Bureau of Mines has recently conducted a study of results obtained in analyzing similar samples of coal and coke by 25 laboratories throughout then country, in comparison with results obtained in the Bureau's coal laboratory at Pittsburgh. The purpose of this work was primarily to obtain a comparison of the methods of coal analysis used by the laboratories of the American Gas Association. Therefore, four standard samples of coal end one of coke ware prepared in the Bureau of Mines coal laboratory at Pittsburgh, and portions sent to each laboratory. At the same time, a like number of standard samples were submitted to 12 commercial laboratories rot affiliated with the Association, for the purpose of comparing their analyses with the results is obtained by the U. S. Bureau of Mines and the American Gas Association. Tire comparison is based on the average of 24 analyses by the Bureau of Mines on each kind of coal, and the accompanying curves show the deviation from this average analysis, together with deviations from the check limits of the American Society for Testing Materials.

Jan 1, 1923

By C. A. Rhoades

A major contributor to the problem of short life expectancy for blade-type conveyor belt cleaners is uneven wear along the blade edge. Uneven wear results in the formation of channels in the blade edge, which allow material to be carried back between the blade and the belt. In an effort to reduce the uneven wear problem, the U.S. Bureau of Mines has studied the mechanisms responsible for effective belt cleaning. From this study emerged a design for a cleaner blade that would greatly reduce uneven edge wear. The design consists of a standard cleaner blade incorporating air passages that allow for the expulsion of air along that part of the blade edge in contact with the conveyor belt surface. The results of 18-h tests indicated that the expulsion of air on the blade edge prevents scratches from developing into deep grooves. These tests showed that effective blade cleaning life can be extended 25 times using the pneumatic cleaning blade, compared with solid metal cleaning blades.

Jan 1, 1989

By A. V. Petty

In accordance with its objective to maximize minerals recovery from secondary domestic resources, Bureau of Mines conducted research on recycling chrome refractory wastes. Since 20 pct of the U.S. demand for imported chromite is used in the production of refractories, primarily for the steel, copper, and glass industries, samples of used chrome-containing refractories from copper converter and reverberatory furnaces were investigated to determine their potential for recycling. The samples were beneficiated using a combination of wet magnetic separation, flotation, and leaching techniques, and the concentrates were reformed into briquets for refractory evaluation. Small refractory test specimens produced from the beneficiated concentrates gave modulus of rupture values at 1,350° C comparable to those of commercial mag-chrome brick of similar composition; however, grinding the waste refractories to at least minus 65-mesh was required in order to liberate the metallic copper. Most of the copper was easily recovered using conventional beneficiation techniques, but the finely ground chrome concentrate would require briquetting, calcining, and crushing to produce a coarse grain suitable for recycling into secondary mag-chrome refractories.

Jan 1, 1981

The Bahamas Oil Refining Co. (BORCO) refinery in Freeport continued to operate at less than half its full 500,000-barrel-per-day capacity. Although owned through subsidiaries by the Carey Energy Corp (65%) and Standard Oil Co. of California (35%), BORCO is ineligible for participation in the Crude Oil Entitlements Program granted to companies operating within the United States proper or its territories. Like some other Caribbean refineries, BORCO has suffered a loss of normal market outlet due to the wt advantage afforded U.S. refineries by the Entitlements Program. Saudi Arabia, Nigeria, and Libya are the major suppliers of crude for the refinery. Its principal products, motor spirits, aviation fuel, distillate fuels, and residual fuel oils, were marketed in the United States and Puerto Rim. The Government-owned Bahamas Development Corp. and Burmah Oil Co. Ltd., held discussions pertaining to a renegotiation of Burmah Oil's management contract for the Grand Bahama Oil Transshipment terminal. The desired contract modifications were not made public but financial problems have plagued the terminal and its operation since construction started in 1972.

Jan 1, 1981

By C. L. Karr

The U.S. Bureau of Mines is optimizing the design of an air-sparged hydrocyclone. This report summarizes the initial stage of the project-the prediction of collision efficiencies for use in a comprehensive air-sparged hydrocyclone model. The equations of motion are presented in nondimensional form and solved numerically for a small spherical particle passing around a larger bubble in an infinite fluid under the influence of a strong force field. Collision efficiencies are determined from the calculated particle trajectories for values of Stokes' number, K, between 0.01 and 100 and for values of the nondimensional force, W, between 0.0 and 100. These large values of K and Ware needed to model high-performance flotation devices like the air-sparged hydrocyclone; solutions for the required K and W values have not appeared in the literature prior to this study. Effects of changes in particle-to-bubble radius ratio are considered for both viscous and potential flows. The results help predict the improved recovery of fine particles when flotation is performed in a strong force field.

Jan 1, 1990

By J. H. Maysilles

The Bureau of Mines, U.S. Department of the Interior, is investigating several types of low-grade uranium deposits. Projections indicate that an increased percentage of future production will be derived from such sources. One material studied was from the Coso Mountains of California; this material contained 0.04 to 0.12 percent U3O8. The deposit contains at least two distinct types of mineralization. The material representing the bulk of this deposit was amenable to acid leaching; 80 to 85 percent U308 extraction resulted from leaching with 20 to 40 pounds per ton of sulfuric acid. No oxidizing agent was required. This ore fraction could be treated by either agitation or percolation leaching. Uranium recovery and purification from the acid leach solution was accomplished using anion exchange followed by precipitation with hydrogen peroxide and ammonia. The second type of mineral was very refractory to acid leaching; a maximum extraction of only 44 percent was obtained with sulfuric acid. Nitric and hydrochloric acids were ineffective also.

Jan 1, 1978

By Robert P. Vinson

The U.S. Bureau of Mines evaluated a light-scattering technique for discriminating between spherical and nonspherical particles. This evaluation was a three-step procedure. The first step required collecting light-scattering data for a variety of particles. This was accomplished with a particle analyzer called the DAWN-A. The DAWN-A measured the scattered light intensities of individual particles at a forward scattering angle of 40°. These DAWN-A measurements of individual particles are called scattering signatures by the Bureau researchers. The second step in this evaluation was to calculate a sphericity index number using the scattering signatures produced by the DAWN-A. The sphericity index number can range from 0 to 1. A calculated sphericity index of 1 would show that based on the intensity of scattered light, the particle was a perfect sphere. The third and final step of this evaluation was the comparison of the calculated sphericity indices of the various particles. Comparing these indices made it possible to discriminate between the nearly spherical waterdrops and the nonspherical coal and rock dust particles.

Jan 1, 1993

By Thomas A. Gray, Lynn M. Crayne, Michael A. Trevits, Phil Glogowski

Mine seals can be remotely constructed in underground coal mines, through vertical boreholes, when direct access to a fire is impossible or considered to be too dangerous. This method has great merit because boreholes can be drilled to specific mine areas and seals can be positioned close to a fire zone. The technology however, can be largely ineffective if the constructed seals do not provide effective barriers to airflow or cannot be used to impound water and other inert materials. Unfortunately, no viable alternatives exist to sealing the entire mine at the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Lake Lynn Laboratory (LLL). Under this effort, Howard Concrete Pumping Company and GAI Consultants, Inc. have joined forces to evaluate a potentially significant improvement to the current state-of-the-art. This paper will cover development of novel technology for remote mine seal construction, evaluation of the materials used, construction practice, and follow-up testing.

By John J. Sammarco

The functional safety of programmable electronic (PE) mining systems is an international issue and concern. From 1995 to 2001, 11 PE-related mining incidents in the U.S. were reported by the Mine Safety and Health Administration (MSHA); 71 PE-related mining incidents were reported in Australia. MSHA does not have regulations for formal evaluations of the functional safety of PE mining systems. Hence, the National Institute for Occupational Safety and Health (NIOSH), in partnership with MSHA and the industry, generated the NIOSH safety framework for functional safety of PE mining systems. An overview of the NIOSH framework is given; the key framework elements, the safety life cycle and safety integrity levels are detailed. The safety framework approach has impacted the national and Australian mining industries by enabling the industries to advance from an ad-hoc approach to a formalized and systematic functional safety process. In retrospect, valuable lessons were learned for addressing functional safety and for changing industry perspectives and practices. These lessons continue to benefit mining and are applicable to other industries as well.

By Donald O. Capstick

In 1981, U.S. Bureau of Mines personnel conducted a survey of claims and prospects in the Wheeler Ridge RARE II area to determine if mineral resources or potential for resources exists at deposits in the area. Results of Bureau of Mines investigations indicate the area contains no identified mineral deposits. However, the geologic setting at the Round Valley Peak Prospect near the center of the study area is considered to be favorable for the discovery of tungsten resources with associated molybdenum and copper. Tungsten deposits, should they be present, would be expected to occur at depth in tactite at or near the calcareous rock-granite intrusive contact. Sand, gravel, and stone deposits in the area are not considered to be resources because equal or better quality material is available closer to major markets. INTRODUCTION The 16,200-acre (6,560 ha) Wheeler Ridge study area is 11 mi (18 km) northwest of Bishop, California, on the eastern flank of the Sierra Nevada range. The John Muir Wilderness adjoins the study area's western boundary (fig. 1).

Jan 1, 1983

By Walter J. Frank

Thls report summarizes work done under Bureau of Mines contract H0357100, "Development of a Crimp Connector for Trailing Cable Splices." The purpose of this effort was to establish optimum connector design conditions to meet flex cycle, pullout and electrical resistance criteria on phase power conductors. Field testing of "optimum design" connectors is briefly discussed. One of the primary objectives of contract H0357100 was to enable one to design better performing phase conductor connectors. Illustrating the practical significance of this 1s a discussion on the development of a new splice kit for trailing cables. The connectors in this kit were designed in accordance with the design methods described in the contract final report. Kit components, test data, and a connector installation tool are also discussed. The successful effort on the phase connector has resulted in contract H0377042, entitled "Design and Testing of Joining Sleeves for Trailing Cable Ground and Pilot Wires." The purpose of this contract (currently in effect) is to improve ground-conductor and pilot-wire performance. Significant findings to date are discussed.

Jan 1, 1979

By Clarence O. Babcock

ROCK BEHAVIOR has proved of national interest in a variety of fields. The behavior of rock consequent to a nuclear blast was used to detect such blasts, as criteria for the design of underground military defense installations that would resist nuclear blasts, and for judging the feasibility for peaceful uses of nuclear explosives. An obvious peaceful application of nuclear explosives would be for large-scale rock excavation, and plans were presented during the year to improve the present Panama Canal or create a new canal by this method. These plans were based largely on earlier crater tests that demonstrated rock behavior when subjected to a buried nuclear blast. A knowledge of rock behavior under impact was used to evaluate the materials of the moon by means of the geometric configurations visible in the close-up pictures of the moon surface taken by the U.S. rocket Ranger 7. The composition of the moon must be considered in devising methods for taking samples of the surface layers or in designing underground shelters as bases for future explorations of the moon.

Jan 1, 1965

By Mark A. Ackerson, Kenneth E. Hjelmstad

An ideal fire warning alarm system for underground mines would be low cost, convenient, fast, reliable, and able to warn all underground workers. Present warning systems, such as phones, messengers, and stench, fail one or more of these criteria. The U.S. Bureau of Mines may have devised the ideal system. The one way communication system employs a large loop antenna and transmitter to create a 630 hertz (Hz) electromagnetic field to send information through-the-earth to cap lamp battery mounted micro- receivers worn by underground miners. Field tests of prototype equipment in 1986 resulted in through-the- rock signal transmission of over 762 m (2500 ft). Subsequent hardware upgrades for more recent tests resulted in transmissions of over one mile. Recently developed receiver circuitry employs phase- locked-loop detection circuitry responsive only to a specific series of pulses of given time duration, that eliminates false alarms from electromagnetic noise emitted by mine equipment, power lines, or lightning. A multichannel system can relay standard messages to miners

By Maria I. De Rosa

The major fire and fire injury findings for all coal mining categories for 1990-1999 are reported in tables 37-38. Table 39 and figure 13 show the number of fires. fire injuries, risk rates, employees' working hours, and coal production (under- ground and surface coal mines only) by time period for all coal mining categories. Table 40 shows major findings (for under- ground coal mines only) for 1978-1992. For all coal mining categories, 458 fires occurred during 1990- 1999; 157 of those fires caused 164 injuries and 2 fatalities (Ewhr = 2,070 x l0%r, Irr = 0.016: C'P (for underground and surface coal mimes only) - 10,363 x l0\t, Frr = 0.044, LWD = 14,753). Twenty-nine fires and 17 injuries involved contractors. Sixty-six fires required firefighting interventions by mine rescue teams (25 times in underground mines) and fire brigades and fire departments (at least 41 times at surface coal operations). In all, 51 fires destroyed or heavily damaged equipment (including 16 pieces of mobile equipment) because of failure of other firefighting methods, late fire detection, undetected fires, or fire size. A total of 114 fires were detected late, and 42 fires were undetected. The greatest number of fires and fire injuries occurred at surface coal mines; the highest risk rate values were also calculated for this category. For all coal operations, the ignition sources that caused the greatest number of fires were flame cutting/welding spark/slag/flames (1 03 fires or 23% with 69 injuries), hydraulic fluid/fuel sprayed onto equipment hot surfaces (98 fires or 2 1 % with 29 injuries), spontaneous combustion/hot coal (62 fires or 14%), electrical short/arcing (49 fires or 11% with 18 injuries), and conveyor belt friction (3 1 fires or 7% with 6 injuries).

Jan 1, 2004

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines (USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two for-mulations resulted in stable gels that lasted for at least 12 months in the mine. Semicontinuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both in terms of productivity and enhanced mine safety.

Jan 1, 2010

By Andrew B. Cecala, Edward D. Thimons, George W. Klinowski

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 1993