Search Documents

By Helen W. Lang

This report describes a monitoring system applied by the Bureau of Mines to provide rapid, continuous determination of the main constituents of exhaust gas during the Bureau's approval schedule testing of diesel engines for under-ground use. Commercially available continuous analyzers with strip chart readout are employed for nitric oxide (mass spectrometric), carbon dioxide (nondispersive infrared), methane (NDIR), carbon monoxide (NDIR), and oxygen (polarographic). Good correlation is obtained between the continuous instrumental results and those obtained by batch chemical and gas chromatographic methods.

Jan 1, 1969

By Annie G. Smelley

The Bureau of Mines, U.S. Department of the Interior, as part of its mission to effect pollution abatement, conducted research to devise means for disposing of phosphatic clay wastes and reclaiming mined land. Part of the investigation was performed in a cooperative research project with 10 phosphate companies in Florida. The colloidal properties of the phosphatic clay suspensions, called slimes, make them difficult to dewater and dispose of without impoundment storage aboveground. Various reagents to flocculate and dewater these plant wastes were evaluated, and a polyethylene oxide polymer was found to function in a specialized flocculation dewatering technique. The flocculation dewatering method was investigated in bench-scale batch tests and applied in continuous dewatering tests using standard mineral-processing equipment. In continuous tests at feed rates of up to 58 liters per minute, wastes at 4 percent solids were dewatered to about 20 percent solids. About 0.8 kilogram of polymer was used for each metric ton of dry waste clay solids; processing time was about 4 minutes. Requirements for the treatment system are (1) proper mixing of the clay-waste feed and flocculant, (2) rapid removal of water as it is released, and (3) physical manipulation to promote cohesion of solids.

Jan 1, 1979

By David F. Gearhart, Thomas M. Barczak

This U.S. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (9 compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 1992

By W. C. Wahl, M. M. Fine

Leonardite , a naturally occurring , partially oxidized form of lignite with a high content of humic acids , was investigated as a binder for iron ore pellets . Although insoluble in original condition , leonardite forms watersoluble salts with good binding properties when treated with certain alkalis such as sodium hydroxide . Soluble leonardite imparts excellent dry strength to pellets , but green strength is somewhat lower than that obtainable with bentonite . However , green strength can be improved by adding a small amount of calcium hydroxide to the leonardite - concentrate mixture . Leonardite binders were used successfully on three of the four different concentrates tested .

Jan 1, 1964

By Tobias W. Goodman

The U.S. Bureau of Mines used a contact drilling strategy with short-collared assemblies in order to rotary drill long horizontal methane drainage holes in the Beckley Coalbed near Glen Daniel, WV. By decreasing the thrust, and increasing the rotation of the drill bit when in contact with the roof and floor rock, assemblies with 1-ft (0.3-m), 10-ft (3- m), and 144 (43-m) long collars were made in deflect and stay in the coalbed. Successful application of this procedure resulted in holes drilled full length in coal with the original assembly including bit. The test assemblies deflected away from the original bearings of the holes during drilling and arced. Four holes were drilled to depths ranging from 478 ft (145.7 m) before the strategy was developed, to 4,034 ft (1,230 m) when the strategy was applied. Total length of the holes in coal was 8,590 ft (2,618 m). After 577 days the total methane captured by the holes was 221,600,000 ft? (6,276,000 m3). The methane flow rate peaked at 805,000 ft3/d (22,798 m3/d), then decreased to stabilize at 670,000 ft?/d (18,974 m3/d) after 6 months.

Jan 1, 1989

By Graham W. Mark

A chemical method of analysis for beryllium was developed recently in Bureau of Mines laboratories. In this method, quinalizarin (1-2-5-8 tetrahydroxyanthraquinone) in N/4 NaOH is used as a colorimetric titration reagent. This solution has a reddish-purple color, whereas the solution containing equivalent amounts of beryllium and the dye is rather blue. In the titration procedure, standard quinalizarin solution is added to the unknown beryllium sample and to two standard beryllium samples of different but known concentrations. Then adjustments in concentrations of BeO in the two known and of quinalizarin in all three are made until the red-violet shade of the unknown is halfway between that of the two knowns. The amount of BeO in the unknown is calculated from the known BeO content of the solutions between which it lies. It is extremely difficult to distinguish the slight differences in shade of these solutions without the use of a proper light filter, especially when the concentration is over 0.1 mg. of BeO, so a study was made of the transmission characteristics of quinalizarin in N/4 NaOH and of the corresponding beryllium complex to determine what filter would give the most contrast.

Jan 1, 1950

By K. K. Kershner

The purpose of this research by the Federal Bureau of Mines was to investigate the recovery of tin from mine-run ores and low-grade concentrates. Over 95 percent of the total tin in such materials was volatilized to tin chlorides at temperatures ranging from 520° to 565° C. Gaseous mixtures of hydrogen and hydrogen chloride were used for reducing cassiterite to stannous oxide and for converting this compound to tin chlorides. The chlorides were swept from the reaction zone of an oscillating kiln by a rapid flow of reactant gases and collected in a condensing system. Losses of tin that occur in current metallurgical processing were prevented. Approximately the same time of treatment was required for minus 35-mesh mine-run ores and low-grade concentrates. In a continuous process, the circulating gases would require some enrichment.

Jan 1, 1961

By Willis Beckering

The Bureau of Mines designed a cell having four variable compartments in series to facilitate analysis of multicomponent mixtures. Use of the cell considerably decreases the time required for differential absorption analyses. A solution of a major component is placed in each compartment, and the light absorbed by each of these components is varied by increasing or decreasing the path length of the appropriate cell. Simple calculations then establish the amount of the component present. In analyzing unknown mixtures, compensation is made for compounds known to be present, and the differential spectrum representing components not accounted for is recorded and analyzed.

Jan 1, 1966

By Jami M. Girard

INTRODUCTION Slope stability accidents are one of the leading causes of fatalities at U.S. surface mining operations. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to reduce the fatalities associated with slope failures and other unexpected failures of ground. The purpose of this paper is to introduce various warning signs of slope instability so operators are better able to recognize hazards. The most common slope monitoring equipment and practical methods of installation are discussed as well as the limitations of these systems. CONSEQUENCES OF SLOPE FAILURES Unexpected movement of ground causes the potential to endanger lives, demolish equipment, or destroy property. Between 1995 and 2001 (2nd quarter), 34 fatalities were caused by ground instability. This accounts for approximately 15% of all surface mine fatalities (Figure 1). These figures include fatalities classified by the Mine Safety and Health Administration (MSHA) as “fall of face or highwall,” “powered haulage,” “equipment,” and other MSHA accident categories, where the primary cause of the accident was unanticipated movement of the ground. This includes fatalities resulting from bench and highwall failures, rock falls, waste dump and stockpile failures, and the collapse of unknown underground workings. [ ]

By L. C. IlsLey

"There are two general classes of accidents that prevail in and about mines, namely - (1) those that through the nature of mining work can only be lessened, and (2) those that by proper precaution can be eliminated altogether. Explosive accidents that ordinarily take place while explosives are being transported in and about mines belong to the second class, that is, by proper care all such accidents can in general be avoided.The following table gives a brief summary of several accidents and disasters that have occurred in the United States and indicates the need of universal preventive measures as a basic part of all State regulations.ACCIDENTS AND DISASTERS OCCURRING WHILE TRANSPORTING EXPLOSIVES.***"

Sep 1, 1923

By J. W. Paul

Withdrawing timber in coal mines is done for the purpose of inducing the roof to cave in the mined-out areas and thereby relieve stresses in the immediate roof material over the working places adjacent to the breakline of the roof, thus preventing the crushing of the ends of pillars and adding to the safety of those engaged in pillar extraction. A secondary purpose is the recovery of timber for further use either as prop-, crossbars, lagging, sprags or cap pieces. At some mines timber is withdrawn as a precaution against fire which may he of spontaneous origin, because wood always aids a fire of any origin. With some of the power-driven types of machines now in use a greater proportion of mine timber may be recovered, and in mines where pillars are left too narrow for their removal some of the timber in rooms might be salvaged for further use.

Jan 1, 1933

To develop an in-mine water treatment system in which bacterial sulfate reduction and limestone dissolution continuously remove metals and acidity from contaminated drainage. Approach A section of mine tunnel was converted into a water treatment bioreactor by constructing cinder block dams and fang the area between them with a porous substrate mixture of limestone gravel and compost. Readily fermentable materials such as dairy whey, spent brewing yeast, or sugar were periodically added to the reactor. Mine drainage was impounded behind one of the dams and continuously percolates through the reactor substrate at a controlled rate. How It Works The reactor substrate soon becomes anaerobic after it is saturated with mine water. Under anaerobic conditions, sulfate-reducing bacteria consume the organic materials that are added to the reactor and generate hydrogen sulfide (HIS) and alkalinity. The H2S reacts with dissolved iron and heavy metals to form metal sulfide precipitates. The alkalinity raises the pH of the water and induces aluminum to hydrolyze and precipitate as aluminum hydroxide [Al(OH)3]. Additional alkalinity is generated by the continuous dissolution of the substrate limestone. Metal sulfide precipitates and Al(OH)3 are retained within the reactor, and the treated water is discharged. The underground location of the system allows year round operation.

Jan 1, 1994

By L. C. IlsLey

The observations made by Bureau of Mines engineers of permissible equipment installed in about 40 mines have indicated a chance for improvement in designs calling for the use of bolts , screws , studs , etc. , especially with respect to bolt sizes and protection from mechanical injury .

May 1, 1931

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Development of downstream petrochemical and fertilizer industries continues as a major investment area. In 1993, the 15 countries that constituted the region accounted for 29 % of world crude petroleum output, 19 % of world natural gas plant liquid production, and 6 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Regional output was up for most major mineral commodities. A major exception was phosphate rock, which declined sharply owing to reduced worldwide demand. Total crude petroleum output declined by over 100 Mbbls, again owing to slack demand in the major industrial countries.

Jan 1, 1995

By J. P. Rider

Health surveillance efforts indicate that the development of lung disease and overexposure to respirable dust in underground coal mires continues to afflict mine worker. Results from the most recent round (1992 - 1996) of the Coal Worker's X-ray Surveillance Programs indicate that approximately 8% of the examined miners who had at least 25 years of mining experience were diagnosed with Coal Worker Pneumoconiosis (CWP) (category 1/0+). During the period between 1995-1999, mine operators and MSHA inspectors collected 9968 and 1365 dust samples respectively, from longwall designated occupation (DO) personnel. Analysis of these samples showed that 1970 (20%) of the mine operator samples and 25.8 (19%) of the MSHA samples5 exceeded the 2 mg/m3 dust standard. The continued development of CWP in coal mine workers and the magnitude of respirable dust over-exposures in longwall mining occupations illustrate the need for improved dust control technology on longwalls. Figure 1 illustrates the major longwall dust sources as determined in the early 1990's.4 This article describes the ongoing research to find ways to minimise shearer dust levels as a function of changes in dust control parameters, and research to determine the impact of high air velocities on shield dust entrainment.

By John Nagy

Results of initial research by the Bureau of Mines are given on the dust explosion hazard of float coal and on the related factors of occurrence, rate of production, sampling techniques, transport, and deposition of float coal. Tentatively, it is suggested that where float coal deposits prevail, a mini-mum of 80 percent incombustible be maintained in the top 1/8-inch layer to neutralize the explosion hazard of the surficial coal deposit.

Jan 1, 1965

By Oliver Bowles

"Introduction.During recent months the Bureau of Mines has conducted a detailed study of the slate industry with special reference to increased efficiency in its production, preparation and utilization. The results of these investigations will be incorporated in a forthcoming bulletin. The purpose of this preliminary paper is three-fold. One object is to bring to the attention of slate producers certain modifications in manufacture and classification which would encourage a wider use of slate. A second purpose is to direct the thought of roofers toward the importance of proper laying of slate, and the third object is to acquaint the general public with its enduring qualities.Origin and character.Without entering into any detailed discussion of the origin and history of slate, a subject to be covered in the bulletin mentioned, it may be of interest to the general reader to know that slate is originally formed from mud or soft clay, carried down by streams and laid down in successive layers in deep water. The pressure of superimposed materials gradually compresses the clay into a firm rock known as shale. In many places this shale was, during the succeeding ages, subjected to intense pressure and folding due to mountain-building forces within the earth. This intense pressure, together with high temperature, changed the clay into other minerals such as mica, chlorite, and silica, which are very resistant to weathering, and also developed a very definite cleavage or splitting direction which characterizes the rock as slate. It is this property which renders slate of value for roofing, for, by using a broad chisel and a wooden mallet, a slate worker can readily split it into thin sheets which are later trimmed into rectangles of various sizes."

Jul 1, 1921

By RV. Ramanl, KV. K. Prasad, M. Swaminathan

The objective of the research in this project is to develop a knowledge based expert system for aiding the planning of mine ventilation systems. This system focuses on mine ventilation system design from a coal mine dust control standpoint. It is recognized that mine ventilation system design is an engineering problem involving not only rote numerical calculations to solve the pressure quantity problem but also substantial judgement and expertise to analyze a problem situation and Interpret the results of an algorithmic program. The thrust of this project is to i) extract this knowledge from public domain sources and recognized experts in industry, government and academia, 11) represent this knowledge in the form of IF ... TI-IEN rules in an expert system (ES) and 111) interface the developed expert system with a mine ventilation network analysis program vis. PSUMVS (Pensylvania State University Mine Ventilation Simulator). By providing the numerical computing and qualitative reasoning aspects of mine ventilation system design in a single Integrated system, better quality decision support will be made available to apprentice users.

Jan 1, 1988

Improve the strength and other properties of steel alloys. Approach Research by the U.S. Bureau of Mines indicates that steels melted and solidified under high nitrogen pressure acquire yield and tensile strengths that are up to four times the strengths of comparable stainless steel alloys without nitrogen. Fatigue strength, creep strength, and other mechanical properties are also improved. Strengthening occurs by two mechanisms: (1) increasing dissolved nitrogen in the lattice and (2) formation of dispersed metal nitride phases. Nitrogen Alloying Nitrogen alloying of a steel is generally done by introducing metal nitrides during melting of the steel. The concentration of nitrogen is limited to its equilibrium solubility at 1 atmosphere. For face-centered-cubic (fee) iron, that solubility is approximately 0.4 weight percent (wt%). For body-centered-cubic (bee) iron, solubility is 0.05 wt%. This solubility limitation can be overcome by melting the metal in a pressurized vessel. European steelmakers currently have metal-processing systems that can melt and pour tons of steel under nitrogen pressures exceeding 4 megapascals (MPa) (40 atmospheres). They have achieved nitrogen concentrations as high as 1.0 wt% in these (stainless) steels. The tensile strength is approximately twice the tensile strength of similar steels without nitrogen.

Jan 1, 1992

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the New Galena Deposit in an endeavor to find an additional source of supply of lead. In Bucks County, lead and zinc minerals have been found in shales over a largo area west and northwest of Doylestown. Considerable mining has been done in the vicinity of New Galena on the North Branch of Noshaminy Creek, 3 miles northwest of Doylestown. It has not been possible to obtain a satisfactory history of the New Galena mine, as there is much disagreement in statements. Most of the mining was done in open pits. Two shafts were sunk to shallow depth; one of these became part of the main pit' which is 256 foot long, 50 to 75 feet wide, and 20 to 44 feet deep. Small pits 8 to 10 foot square wore sunk on the ore zone, which extends some 1450 feet to the southwest. The rock containing the minerals is either black or gray shale. The gray material closely resembles limestone. The following minerals have been reported from the mine: quartz, ankerite, calcite, galena, sphalerite, pyrite, chalcopyrite, and bornite. Some of the galena has yielded 10 to 15 ounces of silver and 10 cents in gold per ton. The average grade of the ore as mined is not known. To investigate the downward extension of the ore shoot, the Bureau drilled two holes aggregating 373.9 feet, No additional ore was developed by this work.

Jan 1, 1950