Search Documents

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 3,924 samples, representing the products of 116 companies. The samples were collected during June, July, and August, 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers, The data were obtain& by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By J. G. Kirby

According to the Bureau of Mines annual survey, there were 319 petroleum refineries in the United States as of January 1, 1957 capable of processing 9,123,674 [ ]-barrels of crude oil daily. This was the first time in eleven years that the total number of refineries increased. The crude throughput capacity of the refineries increased 491,284 barrels daily (6 percent) above the January 1, 1956 capacity. The East Coast and Texas Gulf Coast refining districts accounted for 60 percent of the additional capacity installed. Three new refineries were put into operation on the East Coast during the year with a total daily crude throughput capacity of 154,434 barrels while the other refineries in the district report a net loss in capacity, installing equipment capable of processing 140,000 barrels, but dismantling equipment with a capacity of 150,100 barrels. In the Texas Gulf Coast district, one new refinery with a daily crude oil capacity of 5,000 barrels was placed in operation in 1956 and 143,700 barrels of crude capacity was added to existing refineries. The capacity of the average refinery to process crude oil increased from 27,145 barrels daily to 28,601 barrels in 1956.

Jan 1, 1957

By Aleksandar D. Bugarski, Robert J. Timko

Despite extensive research efforts conducted in the past decades, occupational health risks associated with exposure to nano and ultrafine aerosols emitted by diesel power equipment are still not completely understood. The complexity of physical and chemical properties of diesel aerosols, constantly changing with the implementation of advanced diesel emissions control technologies, make this task rather challenging. The objective of this paper is to identify and characterize nanometer and ultrafine aerosols emitted by diesel engines in the underground environment and evaluate the effects of selected contemporary control technologies on physical properties, chemical composition, and in-vitro toxicology of diesel aerosols. The physical and chemical properties of the nanometer and ultrafine diesel aerosols are to be characterized through a test series in the NIOSH Lake Lynn Laboratory experimental mine. The crucial part of the study has been development of a facility that allows researchers to generate field results with precision and accuracy characteristics of a laboratory environment. The knowledge obtained from this study should strengthen our understanding of the health implications related to exposure to diesel particulate matter and aid in assessing the potential of various control technologies for reducing this exposure.

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

By Steven R. Davis

Voyageurs National Park in northern Minnesota, and a 30-mile radius area of influence on the United States side of the International Border, was examined for hardrock (nonferrous metallic minerals and diamonds) mineral potential and environmental sensitivity by the U.S. Bureau of Mines. The investigation also included an analysis of current Metallic Minerals Leasing Rules of the State of Minnesota, and the probable effects of changes proposed to the current rules by the State of Minnesota in order to "encourage mineral exploration and development." The study has determined that the proposed changes to the Minnesota State Leasing rules will have minimal, if any, impact on the likely, foreseeable levels of mineral-related activities in the State as a whole, and particularly, in the area of influence to the Park. Voyageurs National Park management was advised on the extent and character of the proposed rules changes, and on those items of concern meriting a specific and timely response by the National Park Service.

Jan 1, 1994

A system to continuously measure the concentration of radon in mine ventilating air has been developed and tested in a uranium mine. In use, the air/radon mixture to be monitored is pumped through filters into a scintillation cell where nuclear decay of the radon produces flashes of light. These are electronically counted, giving a quantitative measure of the radon present. Air is continuously drawn from the mine atmosphere into the radon sensor box. This air sample passes through two filters into the detector cell as shown in the schematic diagram. A portion of the radon in the detector cell will experience nuclear decay, producing polomium 218 and an alpha particle. The alpha particles from the fraction that decays strike a zinc-sulfide coating on the inside wall of the cell and produce flashes of light. These enter a photo-multiplier tube which records each flash as an electrical pulse. An amplifier increases the voltage of each pulse, allowing electronic screening to remove noise and other undesirable pulses. The remaining pulses are counted by a conventional data acquisition system.

Jan 1, 1978

By A. N. Fried

One of the important problems confronting oil producers in appraising the possibilities of secondary recovery in many California fields is the effect of viscosity on oil recovery by water flooding. In January 1954 there were 554 fields and/or pools, in the State, that produced 1 million barrels daily, and 138 of these pools produced approximately 267 thousand barrels daily of heavy crude oil having gravities below 200 API. Many of these fields are nearing the end of their primary economic life and still have high residual-oil saturations, a favorable factor in water flooding. The crux of the problem is whether or not enough oil can be recovered from these fields by water flooding to make the operation economically successful. Some experiments on the relationship between viscosity and oil recovery have been made by other investigators, but in most instances the viscosity of the oils used in the experiments was lower than the viscosity of the oils found in many of the heavy-oil fields in California. A study was undertaken, therefore, to determine the relationship between oil viscosity and recovery over a wider range of viscosities and to compare the experimental results with those predicted by theoretical calculations.

Jan 1, 1955

By Thomas J. Peters

During the 1982 Bureau of Mines study, 55 lode and 17 placer claims were held in the RARE II area. An estimated 150 lode claims and 50 placer claim, have been located in the study area; five were patented. There are no mineral leases. Gold has been produced from 8 lode mines and stream gravels have been worked for placer gold at 4 sites. Two suction dredges were active in stream gravels, but no significant gravel bars are identified. Identified mineral resources in the Weaver Bally area are gold and byproduct silver. The identified resources are at the Globe Mine, where approximately 33,000 tons of indicated marginal reserves (2,000 tons in the RARE II area, and 31,000 tons in the adjacent proposed Trinity Alps Wilderness) contain 0.45 oz gold per ton and probably 0.1 oz silver per ton. There are an additional 150,000 tons of inferred marginal reserves (35,000 tons in the RARE II area, and 115,000 tons in the adjacent proposed wilderness) averaging 0.38 oz gold per ton and probably 0.1 oz silver per ton. There is high potential for additional resources at the Globe Mine.

Jan 1, 1983

Research personnel from the Bureau of Mines, representatives of the Mining Enforcement and Safety Administration (MESA), and members of the mining industry met with other Government and Industry representatives at three seminars held in Pittsburgh, Pa., November 4, 1975; St. Louis, Mo., November 6, 1975; and Denver, Colo., November L1, 1975, to discuss the results of Bureau-sponsored research on coal mine illumination. The program, aimed at developing suitable illumination systems fur the working; places of underground coal mines, covered hardware development and field evaluation and the status of proposed MESA standards and proposed MESA enforcement procedures. These proceedings contain the opening remarks to the seminars and eight technical presentations an various aspects of coal mine illumination.

Jan 1, 1976

By Ronald P. Hollenbeck

The value of mineral production in Alabama reached a new high of more than $246 million. 4 percent above the previous record established in 1964. New high values were reported for bentonite, portland cement, fire day, kaolin, miscellaneous clay, lime, crushed limestone, crushed marble, mica. salt, and sand and gravel. Among the States, Alabama ranked second in the production of bauxite and scrap mica and third in the production of native asphalt. The mineral industry of Alabama was dominated by the mining and processing of coal and Slone, the manufacturing of cement, and the production of crude petroleum, which together comprised 85 percent of the total value of mineral output, compared with 84 percent in 1964. The iron ore industry continued to decline. Coal production continued to increase, resulting in the State's coal-mining best year since 1948.

Jan 1, 1967

By Vibration Research Group, Natasha K. Lee Shee, Tammy R. Eger, James P. Dickey, Paul-Émile Boileau, Lana M. Trick, Michele L. Oliver

Introduction Industrial exposure to whole-body vibration is associated with injury and discomfort. Certain industries, notably mining, construction, and forestry, involve complex 6 degrees of freedom vibration. Laboratory-based studies of vibration are essential for controlled and systematic evaluation of the human responses to vibration2. The purpose of this pilot study was to evaluate whether the duration of the vibration exposure, and rest between vibrations, significantly influence the subjective ratings of comfort during laboratory-based studies of vibration. Methods Subjects: The cumulative vibration dose was calculated, and was below the health guidance caution zone recommended by International standards3. The experimental procedures were approved by the University of Guelph Research Ethics Board. Ten adult subjects participated in this pilot experiment. All subjects completed the entire experimental paradigm; no subjects complained of pain during or after the experiment. Experimental Design: The experiment consisted of four blocks of vibration exposures; either 15 or 20 seconds of vibration (1 df:Z axis, 3 df:XY plane, 3df:YZ plane, or 6 df) alternating with either 5 or 10 seconds rest. The order of presentation of the four blocks was randomized. Each of the blocks was composed of 37 individual sinusoidal vibration exposures in randomized sequence. This abstract focused on ten identical trials, (6.3 Hz vertical vibration, 0.55 m/s2 RMS) interspersed within each block, in order to assess whether the subjects’ comfort ratings systematically varied between the 15 or 20 vibration exposures, the 5 or 10 second rest between vibrations, or within each block. The experiment involved 43 minutes of vibration within the 62 minute experiment. Vibration Apparatus: A commercial parallel robotic platform was used to apply the specific vibration exposures (R2000, Parallel Robotics Systems Corporation, Hampton, New Hampshire). The subjects sat on a passenger seat from a 1992 Honda Accord that was rigidly mounted to the robotic platform (Figure 1). This robotic system performed the specific vibration exposures operating under closed-loop displacement control. A custom-written Matlab program automated the testing sequence.

Jan 6, 2006

By Chas. F. Jackson

This paper is published as a progress report for the first half of 1929 on the study of wining methods and costs in the Eastern and Central States. Data obtained from 25 mines using open-stope methods are correlated and summarized. Some of these mines have been described in considerable detail in reports already published as Information Circulars. In addition to the published reports on individual mines, considerable data have been obtained from other mines which were visited and studied during the course of the investigation. Many of these mines will later be described in detail in separate papers, and when the field has been covered in this manner it is planned to issue a bulletin on open-stops methods of mining which will amplify the subject matter of the present paper. Definition of ?Open-Stops?. - The term "open-stopes" as employed by the Bureau of Mines is applied to all naturally supported stopes; that is, stopes in which the excavated ore is not replaced by support of an artificial nature other than preps or stulls and in which the ore or (and) capping are not caved during the active life of the stopes.

Jan 1, 1931

By R. E. Cerullo

Many computer programs have been written which are capable of performing a least squares fit, both linear and nonlinear, to data gathered by the petroleum researcher. However, when the petroleum engineer tries to program methods of analysis he has used manually in the past, such as forecasting production by decline-curve analysis, more than a knowledge of the use of existing least squares programs becomes necessary. It is the intent of the authors to report the techniques used in the development of such a decline-curve program.

Jan 1, 1970

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By Floyd G. Anderson

The Federal Bureau of Mines promotes the use of safe and effective dust-collecting devices for rock drilling in coal mines. To insure that such devices are available to the coal-mining industry, the Bureau issues certificates of performance for dust-collecting systems and certificates of approval for dust collectors and rock drills or other mining equipment with integral dust-collecting systems that meet the requirements of an established Schedule.4/ Investigations are conducted under the provisions of the current revision of this Schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for obtaining certificates of performance or approval and lists equipment that has been certified as permissible under Schedule 25 or its revisions as of January 31, 1961. The names and addresses of companies to which certificates have been issued are listed alphabetically at the end of this circular.

Jan 1, 1961

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

On September 4, 2007, Mine Safety and Health Administration, in alliance with the International Union of Operating Engineers and the International Association of Bridge, Structural, Ornamental, and Reinforcing Iron Workers, presented the first annual Mine Construction Maintenance and Repair?s Safety Contractor of the Year Award to Artisan Contracting, Inc., of Cape Girardeau, MO. Eligible contractors located throughout the United States were nominated. Artisan Contracting was nominated by Illinois Cement Company located in LaSalle, IL. Illinois Cement Company is a Division of Eagle Materials Inc., located in Dallas, Texas. Mr. Larry Frankum President of Artisan Contracting Inc., stated, ?While it is gratifying to receive a wonderful award such as this, we must not forget how fragile a good safety record is. We must constantly remain diligent in pursuit of maintaining safe work sites.?

Feb 1, 2008

By Michael D. Balen

During the years 1987 through 1989, the Bureau of Mines Alaska Field Operations Center (Bureau) in cooperation with the Western Field Operations Center and the Alaska Division of Geological and Geophysical Surveys (ADGGS), conducted mining, geological, and geochemical investigations in the 5.7 million-acre Valdez Creek Mining District (VCMD). This investigation was conducted as part of the Bureau's continuing Mineral Land Assessment (MLA) mining district studies program. The Bureau's MLA program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies. The information also provides the basis for decisions that would expand the domestic supply of important mineral resources, primarily strategic and critical minerals. Much of the MLA work is done jointly with cooperating State or U.S. geological surveys.

Jan 1, 1992

By Kristine M. Krajnak

Occupational exposure to hand-arm vibration through the use of powered hand tools can result in reductions in tactile sensitivity, grip strength and manual dexterity. In fact, even acute exposures to vibration cause shifts in vibrotactile thresholds in exposed fingers (2,4,5). Although reductions in tactile sensitivity after acute vibration exposures are transient, cellular changes associated with this shift in sensitivity could lead to the more permanent reductions in tactile sensitivity that are a common symptom of hand-arm vibration syndrome (HAVS). Methods Animals. Male Sprague Dawley rats (6 weeks of age) were used for all experiments. Animals were housed in AAALAC accredited facilities, and all procedures were approved by the NIOSH Animal Care and Use Committee and were in compliance with the CDC guideline for care and use of laboratory animals. Vibration exposures were performed by restraining rats in a Broome-style restrainer, and securing their tails to the vibration platform using 6 mm wide straps that were placed over the tail every 3 cm. Restraint control animals were treated in an identical manner except that the tail platform was set on isolation blocks instead of a shaker. Tail temperature and current perception thresholds (CPTs). Rats were exposed to 4 h of tail vibration (125 Hz, 49 m/s2), or restraint. Tail temperature was collected prior to and immediately following the exposure using an infra-red camera. Sensory neuron function was assessed by measuring CPTs with a Neurometer (Neurotron, Baltimore, MD). Transcutaneous nerve stimulation was applied to the C10 region of the tail. Three frequencies were used to test specific fiber types (5 Hz – C, 250 Hz - Ad, and 2000 Hz – Aß). The intensity of the stimulus was automatically increased in small increments until the rat flicked its tail. Tests at each frequency were repeated until the animals displayed 2 responses that were within 2 CPT (or 0.02 mA) of each other (2-4 tests/animal). CPT tests were performed prior to the exposure, immediately following the exposure, and 24 h after the exposure. Data Analyses. Temperatures were analyzed using a one-way ANOVA with animal as a random variable. ANCOVAS were used to analyze the CPTs at each frequency. Temperature at the time of the CPT test was used as a covariate, and animal was used as a random variable Results Tail temperatures declined between pre and post exposure (F(1,25) = 62.85, p < 0.001; mean ± sem pre 25.96°C ± 0.42, post 20.71°C ± 0.77), but were back to baseline levels by 24 h after the exposure in both groups of rats. The ANCOVAs demonstrated that exposure to a single bout of vibration did not alter sensitivity of C (5Hz) or Ad (250 Hz) fibers to stimulation.

Jan 6, 2006

By Thomas M. Barczak, David P. Conover

Longwall shields provide essential ground control in longwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of-the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (1) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield’s capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.