Search Documents

By Ren G. Dong, Dan E. Welcome

Instrumented handles or dynamometers are widely used to measure hand forces and/or the biodynamic response of hand-arm system. To study hand-transmitted vibration exposure, six generations of instrument handles were constructed or initially developed by researchers in ECTB/HELD/NIOSH. This presentation provided a summary of these handles. Their basic characteristics, limitations, and usefulness are described, which may help their appropriate applications and further improvements. Six Designs of Instrumented Handles Handle 1: The conceptual design is recommended in ISO 10819 (1996)1 for glove test. The grip force is measured by detecting bending strains on a measuring beam in the handle. A special handle fixture was designed to connect the handle to a shaker. Except the screws, the handle and fixture were made from aluminum. Handle 2: The design is based on the principle of shear strain measurement.2-3 Both grip and push forces can be measured simultaneously using this handle. This handle was directly designed for a simulated vibrating tool. Handle 3: This design is basically composed of a handle base, a measuring cap, and two charge-based sensors (Kistler 9212) sandwiched between the base and cap. The handle was also made from aluminum. The fixture for Handle 1 was also used with this handle. This generation of handle has three different handle diameters (30, 40, and 50mm).4 Handle 4: This design is an improvement from Handle 3. The handle fixture was totally redesigned and it was much stiffer than the previous one. The aluminum measuring cap was replaced with a magnesium cap. Handle 5: The basic structure of this handle is the same as that for Handle 3. However, the piezoelectric sensors were replaced with two strain gage based sensors (Interface SML-50). Handle 6: This handle includes two measuring caps, four piezoelectric sensors, and a handle centre base. The handle fixture was the same as that with Handle 4. Methods for Handle Examinations The static and dynamic characterizations were performed using the methods reported by Dong et al.5-6 Results and Discussion Handle 1: The static force measurement depended on the hand grip location on the handle. Its natural frequency was less than 200 Hz.5,6 Because the transmissibility of gloves may not vary significantly with the applied grip force, this handle may be acceptable for glove test. However, the force measurements with this handle may not be reliable. Handle 2: The static force measured with this handle was insensitive to the hand acting location. However, when the handle was vibrating, the force signals could be totally distorted. For this reason, it was not used for vibration studies.

Jan 6, 2006

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

Isometric strength is defined as the capacity to produce force or torque with a voluntary isometric (muscle[s] maintain[s] a constant length) contraction. The key thing to understand about this type of contraction and strength measurement is that no body movement occurs during the measurement period. The tested person's body angles and posture remain the same throughout the test. Isometric strength has historically been the type most studied and measured. It is probably the easiest to measure and to understand. Some strength researchers feel that isometric strength data may be difficult to apply to some "real life" situations because in most real circumstances people are moving - they are not static. Other researchers counter that it is equally difficult to determine the speed of movement of a person or group of persons doing a job (each moves in his or her unique manner and speed across the links and joints of the body). Thus, dynamic strength test data collected on persons moving at a different speed and/or in a different posture from the "real world" condition will be just as hard to apply. In truth, neither is better - they are different measurements. Both researchers and users should collect and use data that they understand and that fits their application. Workplace Assessment When a worker is called on to perform a physically demanding lifting task, the external load produces moments - tendencies to produce motion, also called torques - about various joints of the body.(1) Often these moments are augmented by the force of gravity acting on the mass of various body segments. For example, in a biceps curl exercise, the moment produced by the forearm flexors must counteract the moment of the weight held in the hands as well as the moment caused by gravity acting on the forearm's center of mass. To perform the task successfully, the muscles responsible for moving the joint must develop a greater moment than the combined moments of the external load and body segment. It should be clear that, at each joint of the body, there is a limit to the strength that the muscle can produce to move ever-increasing external loads. This concept forms the basis of isometric muscle strength prediction modeling.(1) The following procedures are generally used with this biomechanical analysis technique. First, workers are observed (and usually photographed or video-taped) as they perform physically demanding tasks. For each task the posture of the torso and the extremities are documented at the time of peak exertion. The postures are then re-created using a computerized software package, which calculates the load moments produced at various joints of the body as the task is performed. The values obtained during this analysis are then compared to population norms for isometric strength obtained from a population of industrial workers. In this manner, the model estimates the proportion of the population

Jan 1, 1998

By Ricardo Burdisso, Rahul Kadam, Kyle Schwartz, Marty Johnson

Occupational exposure to hand transmitted vibration (HTV) arises from the hand held powered tools extensively used in the mining and construction industry such as rock drills, chipping hammers, chain saws etc. Regular exposure to HTV is the major cause of a range of permanent injuries to human hands and arms which are commonly referred to as hand-arm vibration syndrome (HAVS). In addition to this, the percussive tools generate overall sound power levels in excess of 110dBA in most cases. Such a high sound power level greatly exceeds the maximum permissible exposure limit (PEL) of organizations such as National Institute for Occupational Safety and Health (NIOSH) and the Occupational Safety and Health Administration (OSHA). Long term occupational exposure to this noise has been diagnosed as the main reason for permanent hearing loss in the operators. It is therefore important to develop an understanding of the mechanisms which lead to these high vibration and sound levels and in order to do this a detailed computational model of a pneumatic chipping hammer has been made. This paper presents a nonlinear computational model of a pneumatic chipping hammer. In order to better understand the dynamics of the chipping hammer, the hammer was subdivided into components that are shown in figure 1 (a) (based on a chipping hammer manufactured by Atlas-Copco). The hammer mainly consisted of a center body, a moving piston and a chisel. Compressed air is used to drive the piston inside of a cylinder and on the downward stroke this piston impacts the chisel to create the hammer effect. The machine has one pneumatic valve and this valve regulates the air supply either to the upper chamber or to the lower chamber. The valve changes according to the relative pressures in the two chambers and the supply pressure. There are also twelve different exhaust ports at two positions along the cylinder labeled upper ports and lower ports. As the piston moves the ports can be closed or open (allowing exhaust). Fundamentally, the computational model was made up of two different sub-models, a fluid model and a structural dynamic model as shown in Figure 3 (a) and (b) respectively. The first sub-model takes into consideration the fluid dynamics of the machine since the hammer is driven by compressed air. Equations for the mass flow rate though bleed orifices (assuming an isentropic process) 1 is used to determine the mass flow into and out of the upper and lower chambers. From this the pressures in the two chambers and consequently the forcing on the piston can be calculated. The second sub-model deals with modeling the structural [ ]

Jan 6, 2006

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world's largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

By H. M. Cooper, R. F. Abernethy

Determination of the fusibility of coal ash consists in melting a pyramid of the ash to fluid under prescribed conditions . The conditions of the test are specified by the American Society for Testing Materials4/ and must be adhered to strictly if comparable results are to be obtained . The Society formerly specified a particular type of furnace , but with improvements in design of both electric and gas furnaces , it was decided by the Society to specify only essential details of the test . The Chairman of Committee D - 5 , Coal and Coke , of the American Society for Testing Materials suggested that the Coal Analysis Section of the Bureau of Mines conduct a cooperative investigation on the effect of furnace type and atmosphere upon fusibility of coal ash . The Coal Analysis Section enlisted the aid of a number of laboratories using the more common furnaces to cooperate in the investigation . Four types of gas furnaces burning natural and manufactured gases and two types of electric furnaces with different methods of maintaining a reducing atmosphere were employed . The results from the survey are tabulated herein , and some comparisons are made . There were not enough data from any particular furnace and atmosphere to make a reliable statistical analysis . However , definite tendencies are evident , and attention is called to them by direct comparison. in tables .

Oct 1, 1943

By T. J. Williams

Researchers at the U.S. Bureau of Mines monitored rock mass response to mining of an experimental underhand longwall stope in Hecla Mining Co.'s LUCKY Friday Mine, Mullan, ID. This stope design, the Lucky Friday underhand longwall (LFUL), was proposed as a means of controlling rock bursting while also allowing increased mechanization of mining operations. Instruments were specifically manufactured to monitor three geomechanical factors (backfill performance, ramp stability, and rock mass response) that directly affect the success of stope design. Despite considerable difficulties with instrument installation and survival in the harsh mine environment, especially within the stope fill, sufficient information was collected to suggest that the LFUL method was successful in achieving project goals. This conclusion, in addition to favorable economic and operational evidence, led the mine to adopt the method throughout the mine. Indeed, this study and mining experience suggest that underhand longwall mining could be considered a feasible mining method for rock-burst-prone ground throughout the Coeur d'Alene District. Further Reports of Investigations (RI) in this series present in-depth analyses of the effects of backfill on rock bursting and calibration of a stope numerical model.

Jan 1, 2010

By Launa Mallett, Charles Vaught, Michael J. Brnich

Purpose: This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings. Intended Use: This material has been developed for use in short safety-training sessions such as start-of-shift safety or Atoolbox@ talks. The information can be presented in approximately fifteen minutes and is appropriate for workers at all experience levels. While the examples and illustrations are taken from the underground coal mining industry, the training can be tailored to any work setting by substituting appropriate examples. Materials Needed: The instructor will need to prepare the figures provided in a form that can be seen by the entire class. Suggested methods include the use of: (1) overhead transparencies, (2) laminated pages that can be held up for small groups, and/or (3) handouts with copies of the figures for each trainee. As a supplement, stickers featuring the communication triangle can be placed on hard hats, telephones or other communication devices to remind workers about the key to effective emergency communication. The Talk: The accompanying script is a guide for presenting this safety talk. Training is enhanced if these materials are covered but not simply read by the trainer. Examples given in this guide are from real experiences. To make training more interesting and effective, the instructor can substitute examples from his/her workplace. Additional Resources: The following references will provide further information about communications during emergencies. Auf Der Heide, E. (1989). Disaster Response: Principles of Preparation and Coordination. The C.V. Mosby Company, St. Louis. Mallett, Launa, Charles Vaught, and Michael J. Brnich Jr. (1993). A Sociotechnical Communication in an Underground Mine Fire: A Study of Warning Messages During an Emergency Evacuation@, Safety Science, 16, pp. 709-728. Nigg, J.M. (1987). A Communication and Behavior: Organizational and Individual Response to Warnings@ in Sociology of Disasters: Contributions of Sociology to Disaster Research, R.R. Dynes, B. De Marchi, and C. Pelanda (eds.), Franco Angeli, Milan, Italy, pp. 103-116.

Jan 10, 1999

By H. D. Kline

Manganese ores have been mined in the Batesville district since 1849. Although not continuous over the intervening years, production had totaled approximately 432,000 tons of manganese ore and ferruginous manganese ore to the end of 1953. The ores occur in deposits, essentially low in manganese content, distributed over an east-west belt 24 miles long and 4 to 8 miles wide, the core of which is about 6 miles north of Batesville, Independence County. Although the reserves of high-grade ores in the district are comparatively small, the large deposits of subgrade ores and low-grade manganiferous material comprise potential sources of supply of manganese that may have increasing future importance. The manganese occurs as primary oxide and carbonate minerals in relatively flat-lying limestone and shale formations in which they were originally deposited and as oxides in residual clays resulting from decomposition of the shale and lime-stone. Most of the deposits underlie from a few to over a hundred feet of sedimentary chert, but many occur in the residual clays on exposed slopes of chert-covered hills.

Jan 1, 1956

By H. Nelisse, S. K. Patra, A. Natani, S. Rakheja

The current laboratory methods for assessing the vibration attenuation performance of seats involve repetitive trials with a number of human occupants, and raise certain ethical concerns. Moreover, the measurements with human subjects yield considerable variability in the data. Alternatively, several anthropodynamic manikins have been developed for effective assessments of the coupled seat occupant system [1]. The effectiveness of a manikin in predicting the response of a coupled seat-occupant system lies in its ability to reproduce the biodynamic response of the seated human body in terms of force-motion relationship at the body-seat interface, such as apparent mass (APMS). A number of prototype manikins have thus been developed on the basis of biodynamic characteristics of vertical vibration-exposed seated occupants of different body masses in the vicinity of 5th, 50th and 95th percentile male population. This study concerns with the analysis of a passive prototype manikin to enhance its ability to reproduce the idealized APMS response characteristics of the vibration-exposed seated human subjects defined in ISO-5982[2] for mean body masses of 55, 75 and 98 kg. Methods The APMS responses of a prototype anthropodynamic passive manikin were thoroughly characterized in the laboratory under different excitations and body mass configurations. The manikin was designed with sufficient flexibility to configure mechanical-equivalent models corresponding to seated body masses of 55, 75 and 98 kg, by adding/removing specified masses and springs (Fig. 1). The manikin, configured for a specific body mass, was positioned on a rigid seat without a backrest, which was fixed to the force platform of a whole-body vertical vibration simulator. The simulator was programmed to synthesize random vertical vibration with flat acceleration power spectrum in the 0.4-20 Hz frequency range with two different magnitudes: 1 and 2 m/s2 overall rms acceleration. The total static and dynamic forces of the manikin to and the seat were measured using the force platform, while a single axis accelerometer was installed on the seat pan to measure acceleration due to vertical excitation. The measured data was appropriately corrected for the rigid seat inertia force, and the apparent mass [ ]

Jan 6, 2006

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat-room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By Nadia C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U.S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially water-saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, results, and a remediation plan for in situ leaching based on field observations are presented in this report.

Jan 1, 2010

By J. M. Seward, W. D. Dietzman, M. E. Hawkins

Analytical studies of formation waters are widely used by the petroleum industry as an aid in solving problems such as identifying intrusive waters , corrosion studies , treating injection water , and choosing open or closed water- injection systems . The solution of a problem is often simplified when reliable analyses of the waters under consideration have been made previously . Chemical analyses and electrical resistivity measurements are presented on 267 samples from 74 fields in south Arkansas , and 199 samples from 80 fields in north Louisiana .

Jul 1, 1960

By Joseph E. Matta

The Bureau of Mines conducted a field study to investigate thin suppression of respirable dust by water sprays on a continuous-mining machine. Determining the importance of the top and bottom sprays for two types of spray nozzles was emphasized. Results showed, at a 90-pct confidence level, that (1) at least 70 pct of the dust was generated during the sump cut, even though nearly half of the coal was mined during the downshear operation, (2) the water sprays on the top of the boom had little effect in suppressing respirable dust, and (3) B.D. 5 spray nozzles mounted beneath the boom reduced dust at least 33 pet more than B.D. 5 sprays mounted on top of the boom. A single-cut technique was developed that gave good reproducibility for replicate cuts (coefficient of variation of 20 pct).

Jan 1, 1976

The Bureau of Mines conducted a field study of respirable dust concentrations at an underground room-and-pillar oil shale mine and at the aboveground milling facility to determine the dust generation sources, personal respirable exposure, characteristic minerals, and size distribution of the dust. Major dust sources in the mine were the scaling and blasthole drilling operations, and major dust sources in the processing mill were the screening and crushing operations. Principal minerals found in the airborne respirable dust were albite, analcite, calcite, dolomite, quartz, and orthoclase. The average alpha-quartz content of mine and mill respirable dust samples was 4.1 pct and 15.5 pct, respectively. Carbonaceous material such as diesel particulate accounted for approximately 75 pct of the respirable particulate found in the mine. The average coefficient of variance of respirable dust concentrations measured with approved personal dust samplers in the mine and mill was 7.6 pct, the best precision observed to date with the personal dust sampler operated in the field.

Jan 1, 1977

By Avery H. Reed

RECORD production of marble, kaolin, scrap mica, and talc high-lighted the mineral industry of Alabama in 1962. Among the States, Alabama ranked second in scrap mica, third in the production of bauxite and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by mining and processing of coal and iron ore, and the manufacture of cement, which together comprised 73 percent of the total value of production, compared with 72 percent in 1961. Other important industries were the production of crude petroleum, and stone quarrying. Leading companies were Tennessee Coal & Iron, Southern Cement Co., Southeastern Electric Generating Co., Alabama By-Products Corp., and U.S. Pipe & Foundry Co.

Jan 1, 1963

By E. G. King

Sodium-aluminum and calcium-aluminum silicates are important rock-forming minerals. While many of them are of only theoretical interest, several are of practical importance--as ceramic raw materials and as potential future sources of aluminum. Heretofore, thermodynamic data for these minerals were incomplete; and in many instances missing data were difficult to estimate reliably. This has seriously hampered thermodynamic calculations pertaining both to the natural formations of these minerals and to their decomposition in sintering and fluxing reactions. This paper reports the results of the Federal Bureau of Mines measurements of low-temperature heat capacities of four crystalline silicate minerals--dehydrated analcite (NaAlSi2O6), hexagonal anorthite (CaA12 Si208), lawsonite (Ca2Al2Si2080?2H20), and leonhardite (Ca2Al4Si8C24?7H2O). It augments previous similar measurements of related minerals, which were summarized recently.4 The measured heat-capacity data were used to derive entropy values for the four minerals at 298.15° K. Some relations between these entropy values and those of other similar minerals were discussed. These relations illustrate the difficulty of estimating entropy values of tertiary (or higher) silicates.

Jan 1, 1961

By A. T. Coumbe

During 1953-55, 31,105 miles of pipe for transporting crude petroleum and refined products was laid in the United States, a total slightly below that of the prior 3-year period, according to data compiled by the Bureau of Mines, United States Department of the Interior. The added mileage consisted of 22,571 miles of new pipe, representing about 2,163,807 tons of steel, plus 8,534 miles of secondhand pipe, equivalent to about 419,849 additional tons of steel. During the 3-year period, 13,069 miles of pipe was taken up. By January 1, 1956, the Nation had 188,540 miles of pipeline, an 11-percent gain over the 1952 total of 170,504 miles. The greater use of larger diameter pipelines indicated in recent surveys has continued, as the mileage for sizes 12 inches and over increased from 13 percent of the total mileage at the close of 1952 to 16 percent 3 years later. Crude-oil trunklines 12 inches and over in diameter gained 24 percent during 1953-55, and these larger lines represented 30 percent of the total mileage compared with 25 percent at the close of 1952. Furthermore, the mileage for crude-oil lines less than 12 inches in diameter declined 2 percent and made up only 70 percent of the 1955 total against 75 percent n the previous survey. Product Lines 8 inches and over increased 43 percent from 1952 through 1955 and composed 70 percent of the total mileage compared with 66 percent in 1952.

Jan 1, 1956

By Robert F. Randolph, Christa L. Themann, Efrem R. Reeves, Thais C. Morata, Babette L. Verbsky, David C. Byrne

Objective: Workers with hearing loss face special problems, especially when working in noise. How­ever, conventional hearing conservation practices do not distinguish between workers with normal hearing versus impaired hearing. This study col­lected information from workers with self-reported noise exposure and hearing loss, supervisors of such workers, and hearing conservation program managers through focus groups and in-depth inter­views to evaluate their perspectives on the impact of hearing loss on safety and job performance, the use of hearing protection, and information needed to appropriately manage hearing-impaired workers who work in noisy environments. Results: Concerns about working in noise with a hearing loss could be grouped into the following 10 categories: impact on job performance, impact on job safety, impaired ability to hear warning signals, impaired ability to monitor equipment, interfer­ence with communication, stress and/or fatigue, impaired communication caused by hearing protec­tor use, reduced ability to monitor the environment as the result of hearing protector use, concerns about future quality of life, and concerns about future employability. Mostly, there was an agree­ment between the perceptions of workers, supervi­sors, and hearing conservation program managers regarding difficulties associated with hearing loss and consequent needs. These findings suggest that noise-exposed workers with hearing loss face many of the same problems reported in the literature by noise-exposed workers with normal hearing, with additional concerns primarily about job safety as the result of a reduced ability to hear environmental sounds, warning signals, and so forth. Conclusions: The study outlines potential chal­lenges regarding job safety and hearing conserva­tion practices for noise-exposed, hearing-impaired workers. Awareness of these issues is a necessary first step toward providing appropriate protective measures for noise-exposed, hearing-impaired workers. Of the 19 million adults in the United States with some degree of hearing trouble, nearly half are currently employed in the workforce (NCHS, 1994). More than 30 million US workers are exposed to hazardous noise levels, and noise-induced hearing loss is the most common occupational disease in the United States (NIOSH, 1996). Many workers incur their hearing losses during the first 5 to 10 yrs of employment (Rosler, 1994; Ward et al., 2000) and subsequently work the rest of their careers in an environment where noise and hearing loss interact to impair their ability to hear communication and other important signals. Workers with hearing loss who are exposed to hazardous noise levels present a dilemma to hearing loss preventionists. On the one hand, it is of great importance to ensure that their residual hearing is protected from the damaging effects of the noise to which they are exposed. On the other hand, how­ever, traditional hearing protectors serve to further “deafen” such workers, making communication more difficult and impairing the detection of environmen­tal sounds and warning signals. These workers have special needs that must be addressed. However, conventional hearing conservation practices do not distinguish between workers with normal versus impaired hearing; and, to date, no governmental or professional organization has developed specific guidelines or policies concerning the accommodation of noise-exposed, hearing-impaired workers. Some research regarding noise-exposed, hearing-impaired workers has been completed. These studies have primarily focused on three areas: (a) speech intelligibility in noise versus quiet, with and without various types of hearing protection devices (Abel et al., 1982; Abel et al., 1993; Abel & Spencer, 1997; Rink, 1979; Suter, 1989); (b) signal detection and localization under similar conditions (Abel et al., 1993; Abel et al., 1985; Abel & Hay, 1996); and (c) the use of hearing aids as hearing protectors (Berger, 1986; Dolan & Maurer, 1996; Hétu et al., 1992; Hétu et al., 1993). Research in these three areas has provided an initial framework for development of a management para­digm for these workers. However, each of these studies addressed a very specific research question, examining

By E. A. Loria

The Bureau of Mines analyzed the effects of oxygen, nitrogen, and carbon on the tensile properties of electrorefined vanadium in terms of the Petch equation. The effects of the different impurities and grain sizes on the yield and flow stress between 2730 and 770 K were studied. For specimens of like composition, the values of the Petch parameters 01 and ky obtained by two different methods, extrapolation and grain size, were nearly the same. For high-purity electrorefined vanadium, the 01 value at 2730 K was 10,300 psi (5,150 psi shear). The 01 values for this metal at 1950 and 2730 K were lower by factors of 3 to 4 than for three less pure samples of commercial vanadium metal of equivalent grain size. Nitrogen was more effective than oxygen in increasing 01' the increase being about twice as much for the same impurity level. Carbon produced a slight increase in 01 up to 0.024 percent and then a gradual decrease in 01 to 0.11 percent, the maximum carbon content studied. The corresponding ky values followed the same trend in regard to oxygen and nitrogen additions, whereas the addition of carbon produced no variations at either temperature. Dislocations in vanadium are anchored by carbon, oxygen, and nitrogen with increasing firmness in that order. The high purity of electrorefined vanadium was confirmed by low yield stress and high ductility throughout the low temperature range. The metal also exhibited profuse twinning with high ductility at 1230 and 770 K. The effective surface energy for fracture, y, was found to lie between 3.3 and 3.6 x 1()4 erg cm-2?

Jan 1, 1966