Search Documents

By R. V. Higgins

Many contributions to methods of forecasting the performance of waterfloods of a five-spot pattern have been made by investigators. In most of these forecasting methods, a previously selected sweep efficiency is used, and other simplifying assumptions are employed to obtain the objective. In this paper the calculated oil recoveries from several five-spot single- and multiple-layer stratified reservoirs were made with a minimum of assumptions, and because of the techniques used, no previously selected sweep efficiency was required. As a result, the accuracy of the forecast is increased. Permeability curves and continuously changing saturation gradients are used in every section of the pattern. By means of a potentiometric model, the flood pattern is divided into channels, the centers of which are the streamlines. The channels are divided into cells. As flood water enters, the permeability and saturation of each cell change with time. In this study the production from multiple-sand layers of different absolute permeability but with the same relative permeability-saturation relations are combined. The results are shown for a single- and 10-layer reservoir with a permeability variation of 0.60. The oil rate, water-oil ratio, and recovery are shown as functions of time for a 2- and 20-centipoise oil starting in primary phase and after fill-up.

Jan 1, 1962

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if primary gas toxicities that evolve during the early (~300° C) and later (~.400° C) combustion stages of polyvinyl chloride and chlorinated brattices could be predicted by a smoke particle characteristic, which could be used as a simple and inexpensive test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 2500 and 1,0000 C, for 14 min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were the hydrogen chloride (HCl) and carbon monoxide (CO) concentrations, sample and furnace temperatures, the sample mass weight loss, the average smoke particle diameter (dg and number concentration (no), and the product of the average smoke particle diameter and concentration (dgno)' Results show that the inverse of the smoke particle diameter-concentration (l/dgno) correlates directly with the primary gas toxicities evolved during both stages of combustion.

Jan 1, 1989

By Allan F. Smith

The Bureau of Mines studied toxic products produced by burning eight fire-resistant mines conveyor belts, a brattice cloth, and an electrical cable insulation obtained from laboratory-scale burning experiments under various air-flow conditions. Generally, CO product concentrations for most materials were noticeably higher then the NO2 and HC1 levels that were measured; also, no phosgene was detected. However, several of the fire-resistant belt samples yielded HC1 concentrations that were above the reported lethal level for 1/2 to 1-hour exposures, although these data were limited to flow conditions where air dilution effects were small; the belt materials that showed this behavior included samples of polyvinyl chloride, styrene butadiene, styrene butadiene blends, and a British neoprene which yielded the greatest amount of toxic vapor. In addition, some results are presented on the phosphoric acid concentrations that may be produced from the decomposition of ammonium dihydrogen phosphate when dispersed on a burning coalbed.

Jan 1, 1973

By H. E. Hilliard

The Bureau of Mines investigated hydrometallurgical procedures for concentrating precious metals from a mechanically processed metal fraction of obsolete military electronic scrap. Feed material for the leaching procedures described in this report was the high-tension-separated metal concentrate obtained as a fraction from mechanically processing partially stripped electronic units. Initial pretreatment with a 20-wt-pct-NaOH solution solubilized most of the aluminum. After washing, the resulting residue was incinerated to destroy any organics attached to metal particles. The incinerated residue was leached with 20-vol-pct H2S04 solution using two methods, countercurrent pressure and ultrasonic-aided leaching to solubilize the base metals, predominantly copper. Silver was recovered from the base metal leach residue using 50-vol-pct HN03, and gold contaminated with several percent palladium was recovered from the silver leach residue using aqua regia. The impure silver and gold plus palladium products represent about 1.5 wt pct of the high-tension-separated metal concentrate. Included is a three-step process evaluation study of mechanical processing of general electronic scrap and two hydrometallurgical procedures for leaching high-tension-separated metallic concentrates obtained from the mechanical processing step. Process evaluation concluded that only mechanical processing is economically viable.

Jan 1, 1985

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk, weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

Occupational illnesses are more difficult to identify than on-the-job injuries. Many illnesses related to occupational exposures may not be diagnosed until years after exposure; by that time, exposed workers may have changed jobs or left the workforce. Other approaches to identifying occupationally related illness are analysis of death certificate data (see chapter 2) and medical examination studies of workers known to have high exposures to hazardous agents. Figures 5-1, 5-3, 5-4, 5-6, 5-8, and 5-10 show, for each commodity, the percent of illness conditions reported to MSHA by nature of condition. Heart attacks that occurred on the job are reported without regard to work-relatedness. Figures 5-2, 5-5, 5-7, 5-9, and 5-11 show rates by year during 1986-1995 for selected conditions. Since there are many limitations on the accuracy of illness reporting, the frequencies and rates shown here should not be considered directly comparable across commodities. Figure 5-12 shows estimates for hearing loss by age among coal miners compared to a nonoccupationally noise-exposed population. These data come from a study by Franks [1996] of a group of audiograms obtained on coal miners by a commercial company. Using the NIOSH definition of hearing impairment, i.e., an average hearing threshold level for both ears that exceeds 25 dB at frequencies of 1,000, 2,000, 3,000 and 4,000 Hz, the figure shows that by age 30, more than 10% of miners suffer hearing impairment; by age 50, 90% of miners have hearing impairment. In contrast, only 10% of the nonoccupationally noise-exposed population suffer hearing impairment at age 51, and 50% of the nonoccupationally exposed population have hearing impairment at age 69. Figure 5-13 shows a similar analysis of commercial audiograms on male metal/nonmetal miners [Franks 1997]. At age 20, approximately 2% have hearing impairment using the NIOSH definition of hearing impairment described above. This increases to 7% at age 30, 25% at age 40, and 49% at age 50. In contrast, only 9% of the nonoccupationally noise-exposed comparison population have hearing impairment at age 50. Franks' analysis showed a different pattern for female metal/nonmetal miners; they developed hearing loss at the same rate as would be expected for a non-noise-exposed female population.

Jan 5, 2000

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By John C. Gagliardi

The size and complexity of modern surface haulage trucks has resulted in an increased reliance upon sensors and electronic-based instrumentation for safe and efficient operation. Design engineers need accurate information about the equipment vibration environment to efficiently and effectively build components for installation on mobile mining equipment capable of withstanding the mine environment. Examples of such components include backup alarms, communication equipment, microprocessor-based controllers, and a wide variety of sensors. Unfortunately, this information is not available to the majority of both original equipment and aftermarket equipment manufacturers. To address this problem, the U.S. Bureau of Mines performed field vibration measurements on a variety of surface mining haulage trucks. The vibration measurements were then analyzed and test specifications were developed in the form of envelopes. In conjunction with test specifications, recommendations to aid manufacturers in implementing a vibration environment test program have been included with an illustrative example.

Jan 1, 2010

By Lloyd A. Morley, Alan M. Christman

This report was prepared by the Department of Mineral Engineering, The Pennsylvania State University, University Park, Pennsylvania under USBM Grant Number G0155102. The grant was initiated under the Metal and Nonmetal Health and Safety Research Program. It was administered under the technical direction of the Pittsburgh Mining and Safety Research Center with Mr. Roger L. King acting as the Technical Project Officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this grant during the period February 1, 1975 to July 31, 1976. This report was submitted by the authors on August 31, 1976.

Jan 1, 1976

By A. Wahab Khair

"This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally confined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable ·for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage. INTRODUCTIONOne of the relevant processes in the coal cutting technology is the application of indentation theories. Since most cutting tools in the coal industry are wedge shaped most of the indentation research is found for a wedge shaped tool.A wide range of behavior is found in different rocks subjected to the wedge penetration. A rock which is elastic brittle at standard pressure might become elastic plastic at high confining pressure (Gnirk and Cheatham, 1963). It was also observed that some rocks will merely be crushed and indented by a wedge whereas others will crack and form chips, furthermore the existence or non-existence of chips depends mostly on the geometry of the indenter, type of rock and the depth of penetration (Evans and Murrel, 1958). However, coal cutting technology is mostly explained by models which use rigid wedge to penetrate into a brittle material in which both crushing and chipping will occur (Evans and Murrel, 1958, 1962)."

Jan 1, 1988

By Eric E. Cather

In 1984 and 1986, at the request of the U.S. Forest Service, the U.S. Bureau of Mines conducted a mineral appraisal of the 315,000-acre Lemhi Range study area. This area is located in Lemhi and Custer Counties, about 25 mi south of Salmon, Idaho, and is in the Northern Rocky Mountain physiographic province, Topography is generally rugged with elevations ranging from 5,600 ft to about 11,350 ft above sea level. Since the 1880's, approximately 500 mining claims have been located within the study area; about 400 were current at the time of this investigation. Also, part or all of 12 patented mining claims are in the study area. During Bureau field work, forty-four mineralized sites were examined. The sites had been explored by 80 adits, 14 shafts, and about 140 pits and trenches. At least five properties in the study area have had significant production; the adjacent Mohawk, Grace Phelan, and Snowbird claims had a combined total of 136,000 oz of silver and 67,000 lb of lead; production at the Brown Bull was about 14,800 oz of silver and 115,000 lb of lead; the Portland mine yielded an unrecorded amount of silver. The Hilltop mine, located a few hundred feet outside the study area, produced 125,000 oz of silver, 2.7 million lb of lead, 87,000 lb of zinc, and 62,000 lb of copper from mineralized zones that might extend into the study area. More than 10,000 lb of copper were produced at the Blue Jay mine from workings located about 1,000 ft outside the study area. The Bureau of Mines investigation did not reveal the presence of identified resources in the study area. However, several areas contain mineralized sites and are known occurrences. Some of these warrant additional work to further delineate the mineralization and possibly determine identified resources.

Jan 1, 1988

By Raymond B. Ladoo

[Inquiries are frequently received by the Bureau of Minas relative to occurrence, mining, treatment and utilization of the natural hydrocarbons' such as gilsonite, elaterate, wurtzilite, grahamite, and ozokerite although have been known and used for many years, they are not yet well understood and the amount of recent literature dealing with them as comparatively small. This paper is intended merely to summarize the present knowledge The natural hydrocarbons included in this series are gilsonite, elaterite, wurtzilite, glance pitch, manjak, grahamite, albertite, arid ozokerite and many other minor varieties. With the exception of ozokerite and the other mineral waxes, then all more or less resemble asphalt in that they are dark brown or black bituminous substances of organic origin, generally with a resinous luster. Ozokerite usually light an color with a waxey luster, is closely allied to the others of the series, but is usually considered separately, Unfortunately authorities differ as to nomenclature so that determinations of physical and chemical properties from different sources may riot be readily compared. Abraham Herbert, Asphalts and Allied Substances, 1918, 606 pp. has made one of the most detailed studies of these subjects in recent years, and his classification is used in the main. The following definitions are given by him]

Jan 1, 1920

By G. J. Slavens

The Bureau of Mines has devised technology to recover cobalt, nickel, and byproduct copper from domestic lateritic material using an oxidative, ammoniacal ammonium sulfate leach. Nickel, cobalt, and copper were recovered by solvent extraction and electrowinning. To reduce the cost and complexity of cobalt recovery, an alternate method using lig-nite to extract Co3+ was investigated as reported herein. In the first 25 BV (bed volumes) of solution contacted with lignite, 97 wt pct of the Co3+ was extracted in & downflow column at pH 9.3. After 85 BV, the lignite was loaded to 1.5 wt pct Co3+ and further ex-traction was minimal. The lignite extracted cobaltic ammine complexes rather than cobalt ions and was nonselective as to other -metal cations and ammonium ions. Deleterious cations and 80 wt pct of the nonammine ammonium ions were removed prior to acid elution of the lignite. The removal of the ammines prior to elution to produce an ammonium-ion-freeCo3+ eluate was only partially successful. Thus Co3+ removal from ammoniacal solutions by lignite is technically difficult and economically unfeasible. It was also determined that reduction of Co3+ to Co2+ occurred during the extraction-elution process.

Jan 1, 1984

By D. A. Wilson

Several promising systems for selectively oxidizing the iron in an iron-tin alloy commonly called "hardhead" were investigated in a research project conducted to devise a method for recovering tin from this troublesome alloy. A satisfactory oxidation method was developed and tested successfully on melts of 2,000 grams. Molten hardhead (near 1,080° C.) was blown with air to oxidize iron and leave tin in the reduced state. Recovery of available tin was 96 to 98 percent. Tin products contained 2 to 0.1 percent iron which was reduced to 0.06 percent by filtration at 250° C. Iron oxide formed during oxidation was absorbed by a fluid flux cover composed of 43 percent silica, 17 percent burned limestone, and 40 percent fused borax. Less successful but nevertheless promising results were obtained with mixtures of steam and hydrogen which were sufficiently selective at temperatures between 600° and 950° C. but did not result in complete oxidation of iron. Carbon dioxide-carbon monoxide mixtures also oxidized iron selectively but incompletely. Both stern and carbon dioxide systems produced sufficiently encouraging results to additional research on these systems.

Jan 1, 1961

By A. B. Hooker, L. C. IlsLey

In lare-scal e blasting, it is customary to fire me.l'\Y shot.!:l simu1. taneously. The electric !atonators ara usually conneced in seies, ard are fired either from a power circuit or :from a blasting ma.chine with large capacity, operated by hand. "!hen :'::ri111; with a blasting ca.chine, trouble with missed shots has been freqi.,.ently e>:pert0nced.. Unit1:i:' thes ,:::rcu:ns tances, the shots that fail to fire are often a gr"up in the t.:E"nter r,f t>e series, Various explaz,.a.tions hs.ve been given as to the cause of the failurs. Tis paper covers a few tests made cy the electrical section of tl:.e Dti..'t'cau. cf Mines, wh;.r.;h may be helpful in understanding the -probable cuse of tl1e misfiring of c.:anter shots, Wh3tever th9 source ot the firir. current generator, magneto, or batter, the CUl"rent delivered th:·01.1.gh a shot-f:?·ing circu.it is determined by t.ae total resistance of ,;he clrcili +.; c:1nd all cure:it leaving th9 p,si tive terminal must return to tre negative te1-minal. If a. metallic circuit is well i1,.sul.:tted, praeti­ccl. l;1 a.ll of the t.'Urrent keepo within the circu.it; but in a. shot-!11·.irig ci.rc1li t, Nhere the ·.vires f:ll·e often 1n c.c,i.cact with the eru:"!ih as i11 wet holer., end whero the ins".lla.tion of the leg wires :i. inadecpa.te to prc·,ent lea.l.tage, the current ma.v tu.e v a.r ious pa the: thro-.. .. gh the nr r. earth.

Aug 1, 1922

By William Eathorne

"INTRODUCTION Retsof mine, adjoining the village of Retsof, Livingston County, New York, is about 5 miles northwest of Geneseo and 55 miles (air-line distance) due east of Buffalo. It is a single-bed rock-salt mine having extensive horizontal workings as much as 2-1/2 miles long and 1 mile wide and has been in continuous operation since 1885. Retsof tine is the largest producing salt mine in North America and is reputed to be the largest active salt mine in the world.Retsof is one of three large salt mines operated by the International Salt Co., Scranton, Pa.; T. Forster Courthope is general manager of Retsof and also of the company's Detroit salt mine in Michigan and has held that position for 27 years. He is assisted by Stanley Martin, general superintendent; R. Goetz, Maintenance superintendent; and John Riordan, mine superin¬tendent. All are old-timers at Retsof and, according to Courthope, contri¬buted the ""lion's share in bringing the mine to its present standard of safety.ACKNOWLEDGEMENTThis circular was made possible by the generous cooperation of T. Forster Courthope and his assistants, Stanley Martin, R. Goetz, and John Riordan. The information and time generously given are gratefully acknowledged.GENERAL INFORMATIONThe rock salt as mined contains about 99 percent sodium chloride and requires only crushing and screening to prepare it for the market. With the exception of a large jaw crusher underground, all crushing is done in a mill building attached to the headframe of the main hoisting shaft (fig. 1).Five sizes of salt are produced, ranging from about 1/2 inch diameter down to minus seven mesh."

Sep 1, 1949

According to contemporary psychophysical theory, the relationship between the strength of a perceived sensation (S) and the intensity of a physical stimulus (1) is best expressed by a power relationship.(1) S=kln (1) This psychophysical principle has been applied to many practical problems, including the development of scales or guidelines for effective temperature, loudness, brightness, and ratings of perceived exertion. Based on the results of a number of experiments using a variety of scaling methods and a number of different muscle groups, the pooled estimate of the exponent for muscular effort and force is 1.7.(2) When applying this principle to work situations, it is assumed that individuals are capable and willing to consistently identify a specified level of perceived sensation (S). For manual materials handling tasks, this specified level is usually the maximum acceptable weight or maximum acceptable force. These phrases are defined by the instructions given to the test subject:(3) You are to work on an incentive basis, working as hard as you can without straining yourself or becoming unusually tired, weakened, overheated, or out of breath. If the task involves lifting, the experiment measures the maximum acceptable weight of lift. Similarly, there are maximum acceptable weights for lowering and carrying. Such tests are isoinertial in nature; however, in contrast to the tests described in Chapter 3, they are typically used to test submaximal, repetitive handling capabilities. Data are also available for pushing and pulling. These are reported as maximum acceptable forces and include data for initial as well as sustained pulling or pushing. Why Use Psychophysical Methods? Snook identified several advantages and disadvantages to using psychophysical methods for determining maximum acceptable weights.(4) The advantages include: • Realistic simulation of industrial work (face validity); • Ability to study intermittent tasks (physiological steady state not required); • Results are consistent with the industrial engineering concept of "a fair day's work for a fair day's pay"; • Results are reproducible; and • Results appear to be related to low-back pain (content validity).

Jan 1, 1998

By Frank E. Chase, Deno M. Pappas, Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: • Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; • Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

By R. R. Sayers, W. J. McConnell

"The health, comfort, and efficiency of men engaged in the mining industry may be impaired, in some instances very seriously, by abnormal physical conditions of the mine air or by variations in its composition. This is true in some of sheet metal mines of the West where high temperatures with varying humidities are encountered. Physiological studies have been made in some of these mines showing the effects of various temperatures end humidities. As it is difficult to carry out studies on many controlled temperatures, it was thought best to make the experiments in a laboratory and apply the results to the industry insofar as practicableThe effects of moderately high temperatures and humidities are more difficult to measure perhaps than the extreme conditions, but may be predisposing causes of fatigue, discomfort and disease, A cooperative study of the physioloical effects of heat and humidity is being conducted by the Bureau of Mines and the U. S. Public Health Service cooperative with the American Society of Heating and Ventilating Engineers, in the Research Laboratory of the Bureau of Mines at Pittsburgh, Pa."

Mar 1, 1924