Search Documents

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

By Robert P. Apa

Energy Incorporated has prepared this final report presenting the results obtained from the program for extracting alumina from anthracite culm along with the recovery of energy. This work has been accomplished under the auspices of the U.S. Bureau of Mines with technical coordination through the bureau's Reno, Nevada facility. The objective of this program was to develop a process to recover alumina and energy from Northeastern Pennsylvania anthracite mining waste. The program included Identification of sufficient resources to support a commercial facility, identification of the operating parameters which maximize alumina and energy recovery, the development of a conceptual process design, preparation of material and energy balance(s), and the performance of a system economical analysis. The program was conducted in three major phases. In the first phase the program concentrated on selecting several anthracite culm banks capable of supporting a commercial alumina producing facility. The chosen banks were then sampled and analyzed leading to the selection of two banks which were chosen far testing. The Harry E. and Eckley culm banks were the ones selected. Material from these banks was tested in Energy Incorporated?s Idaho Falls, Idaho testing facility. Parametric testing was accomplished in an eight-inch-diameter fluidized bed test facility. The test program consisted of twelve separate tests. After critical operating parameters were determined, the second phase started: process development in EI's 18-inch fluidized bed test facility. Three material and energy balance tests were completed in this facility. Following these tests a 72-hour demonstration test was performed. The data acquired from these tests were used in the last phase: the process conceptual design and economic analysis. The design basis was a commercial scale facility capable of producing 500,000 tons of alumina per year for 15 years. Based on the test program, It is technically feasible to build and operate such a plant today. The facility would produce, along with the alumina, 81.5 MWe of electricity for outside consumption. A preliminary rate of return indicates that the plant is not feasible with today's economic conditions. An increase in the market price of either the alumina or the electricity is required to provide an attractive rate of return for the facility.

Jan 1, 1982

By Donald O. Rausch, Robert H. Merrill, David W. Wisecarver, S. Jackson Hubbard

Results are reported for stress - relief borehole - deformation measurements made in three underground openings near open - pit mines in the Ruth mining district , Nevada . A total of 134 deformation measurements were made in 8 boreholes . These measurements determined the regional stresses in the horizons above , below, and at the elevation of nearby open - pit mine floors ; knowledge of these stress conditions is considered essential information relative to certain aspects in the designing of stable pit slopes . The determinations indicate that the stresses in the district are due to the gravitational load of the overburden in a confined stress field .

Jan 1, 1964

By P. J. Colbassani

Samples of mine atmospheres collected by Federal coal-mine inspectors during their inspections and investigations of coal mines, in accordance with provisions of the Federal Coal Mine Safety Act (66 Stat. 692; 30 U. S. C., sees. 451-483) are analyzed routinely by chemical methods at Bureau of Mines laboratories. When samples collected in open workings of nongassy coal mines at points not less than 12 inches from the roof, face, or rib contain 0.25 percent or more methane, the act requires the operator, during operation of such mine, to comply with the provisions of sec. 209, Title II, of the act, which pertain to gassy mines. The methane con-tents of such samples are determined by a physical method based on infrared absorption spectrometry to provide an independent check on analytical results obtained by chemical methods. This information circular describes the equipment and procedures used by the Bureau for determining low concentrations of methane in coal mine atmospheres by infrared absorption spectrometry. ACKNOWLEDGMENTS The authors are indebted to Dr. R. A. Friedel, Chief of Spectrometric Section, Branch of Coal-to-Oil Research, Bureau of Mines, for suggesting the analytical method and for furnishing valuable advice and assistance, and to J. A. Queiser of his staff for making exploratory measurements by this method; to Dr. M. G. Zabetakis of the Division of Explosives Technology for his assistance during the conduct of preliminary experimentation; and to L. B. Berger, Chief, Branch of Health Research, under whose guidance the equipment was procured and the work conducted.

Jan 1, 1958

By Lex B. Golden

The purpose of this investigation was to evaluate the corrosion properties of certain alloys of titanium and to compare them with those of unalloyed titanium. Such information should make it possible to determine the desirability of substituting these alloys for commercially pure titanium in certain applications. Titanium-manganese, titanium-chromium-iron, and titanium-vanadium-iron alloys, with 2 types of unalloyed titanium, I consolidated by arc melting and the other by powder-metallurgy techniques, were included in the study. Tests were carried out in sulfuric, hydrochloric, phosphoric, nitric, and mixed acids and in chloride solutions. All solutions were saturated with air.

Jan 1, 1957

In 2007, a total of 2,030 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Coal mines comprised 13.7% of all mining operations. ? Bituminous mines comprised 92.4% (n=1,875) and anthracite mines 7.6% (n=155) of coal mining operations. ? Approximately 72% of all coal mines were located in three states: Kentucky (28.4%), West Virginia (22.6%), and Pennsylvania (20.5%).

Aug 1, 2009

Etching solutions containing hexavalent chromium ions (e.g., chromic acid) are used in brass finishing, printed circuit board etching, preparation of plastic for plating, anodizing, and various other industrial surface treatment operations. As the solutions are used, hexavalent chromium ions are reduced to their trivalent state, contaminants accumulate in the solution, and the effective acid concentration is reduced. When the etching rate becomes unsatisfactory for the particular operation, the solutions are discarded. This is a problem because the discarded solutions are pollutants, and because replacing the etching solution is expensive. The Bureau of Mines has developed a process for regenerating these spent solutions and returning them to the surface treatment operation without interrupting the etching process. An electrolysis cell containing anode and cathode compartments that are separated by permeable membranes, is used for regenerating the spent solutions. The spent chromic acid solution is fed to the anode compartment and sui (uric acid is circulated in the cathode compartment. Application of a steady electrical potential of a few volts dc across the electrodes causes the copper ions and other contaminants in the spent solution to migrate through the membrane to the cathode compartment where copper is plated onto the cathode. Zinc and the other contaminants remain in the sulfuric acid. At the same time, the complex, trivalent chromium ions in the spent solution are attracted to the anode where they are oxidized to their original hexavalent state. The regenerated solution in the anode compartment is then recycled back to the plant?s etching operation for reuse.

Jan 1, 1980

By Albert E. Schreck

[THE COMPOUNDS of strontium were confused with those of barium until 1790, when A. Crawford discovered that the mineral strontianite, long believed to be a barium mineral, was a compound of a new element. This discovery was confirmed 2 years later by I. C. Hope. The mineral was named strontianite because it was found near the town of Strontian in Argyllshire, Scotland. In 1808 Sir Humphrey Davy isolated strontium metal by the electrolysis of fused chlorides. Celestite (strontium sulfate) and strontianite (strontium carbonate) are the principal strontium minerals. Because of its more widespread occurrence, celestite is more important commercially.]

Jan 1, 1959

By J. W. Town

This report summarizes the results of laboratory investigations made by the Bureau c! Mines on the recovery of mercury from caustic sulfide solutions by aluminum precipitation and by electrodeposition. Statistical methods were used to design the experiments and evaluate the resulting data. Precipitation studies demonstrated tint metallic mercury could be recovered from mercury sulfide-sodium sulfide solutions with aluminum. Other metals and their salts and aluminum, salts precipitated only black mercury sulfide. Over 95 percent of the mercury was precipitated from solutions prepared with reagent-grade chemicals and from cinnabar leach solutions. Two equivalents of aluminum were required to obtain 95 percent precipitation of the mercury. Under optimum conditions 1 gram of aluminum precipitated from 4 to 7 grams of mercury; the excess Aluminum was recovered for reuse. The effects of time and temperature on the precipitation of mercury were minor when compared with the effects of mercury concentration and aluminum equivalents. The particle size of aluminum had no significant effect over the ranges studied. When aluminum was used as a precipitant, the mercury concentration in solution was reduced to below 1.0 grams per liter. Adding arsenic and antimony sulfides to the mercury solution resulted in their coprecipitation with the mercury when the aluminum was added From 95 to 99 percent of both the arsenic and antimony were precipitated as metal, which amalgamated with the mercury.

Jan 1, 1962

By A. F. Robertson

"INTRODUCTION This report is supplemental to R.I. 4178 and deals with the work accomplished between June 15, 1945, and September 7, 1945, on the Mitchell-Hodge mine, Grady mine, Albea and York property, and Cuzzort property.ACKNOWLEDGMENTSIn its program or exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigcal Branch, O. C. Ralston, chief, analyzes samples and performs benefication tests.Acknowledgment is due Mitchell H. Kline, chief, Raleigh Division, Mining Branch; Abraham L. Fox, acting chief, Raleigh Division, Metallurgical Branch; and Rowe McCrae, district engineers, U.S. Bureau of Mines, Gainesville,"

Jan 1, 1946

By G. W. Jones

In the course of experiments on the stabilization of acetylene gas by addition of other gases, notably hydrocarbons such as methane, propane, and butane, it was observed that large quantities of carbon black are produced during the explosion of acetylene or mixtures of acetylene with the, above hydrocarbons, the added hydrocarbon being essentially decomposed into hydrogen and carbon. It is known that in the complete absence of air acetylene explodes upon application of an intense ignition source at pressure above 5.9 p.s.i. gage. The same is true of mixtures of hydrocarbons and acetylene. However, the pressures necessary for explosion are considerably higher in the case of these mixtures and depend on the amount of added hydrocarbon. The present report contains data on gaseous products and the physical characteristics of the carbon black formed by explosion at elevated pressures of various mixtures of acetylene and hydrocarbons as well as other gases, such as hydrogen, helium, nitrogen, and carbon dioxide.

Jan 1, 1950

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Le Système International d'Unités (SI) Equivalents of Common United States Units Length 1 ft (foot) = 0.30480 m Mass 1 lbm (pound mass) = 0.45359 kg Force 1 lb (pound) = 4.4482 N Volume Flow Rate 1 cfm = 0.00047195 m3/s Mass Flow Rate 1 lbm/min = 0.00756 kg/s Pressure (wg at 20° C) 1 inch wg (water gage) = 248.36 N/m2 1 inch wg = 248.36 Pa Power 1 hp (horsepower) = 0.74570 kW Energy 1 ft-lb = 1.3558 J Torque 1 lb-inch = 0.11298 N-m

Jan 1, 1977

By Hanns J. Billmayer

Optimized Operator Compartment layouts based on previous Bureau of Mines activities in standardization and optimization of controls were designed and installed in three operating vehicles. Two National Mine Service 48A-36 TorKars were modified in production prior to delivery to the Quarto Mining Company. An Elkhorn AR-4 scoop owned by Adanac Coal Company was modified in a local rebuild shop. The modified vehicles were then evaluated underground under normal production conditions for a 60 day period. Vehicle operators and management appear well satisfied with the compartment modifications.

Jan 1, 1976

By William J. Wuest

The technical analysis of parameters that can influence roof and rib reinforcement is important to the operation of safe and profitable underground mines. One such parameter, studied in this U.S. Bureau of Mines investigation, is the effect of time on untensioned, resin-grouted bolt anchorage characteristics. A group of seventy-three 4-ft-long bolts with three different grout column lengths were I installed in a stable coal mine roof. The bolts were then subjected to standardized pull tests at various intervals throughout a 37-month period. For each test, load-deformation data were reduced to determine axial stiffness and yield point. The magnitudes of these two anchorage characteristics at the time of installation were compared with results from subsequent pull tests to determine if anchorage capacity deteriorated. Bolts with 18-in grout columns were studied over 9 months, and no measurable loss occurred. Bolts with 48-and 24-in grout columns were studied over 37 months and also exhibited no measurable loss.

Jan 1, 2010

By A. U. Miller

Since coal -mining records have been kept , reports of all mining States show that each year the lives of many workers have been sacrificed in the production of coal , and Illinois has contributed its share , Illinois reports for the 50 years 1882 to 1932 , inclusive , show that 6,673 men were killed -- 6,121 underground , 340 in the shaft , and 212 on the surface . Of the fatalities underground , 3,116 were caused by falls of roof or sides , 1,111 by haulage , 630 by explosives , 577 by gas explosions , 139 by electricity, and 548 by other causes ; 166 of the shaft fatalities were caused by falling down the shaft , 143 by the cage , and 31 by other causes ; 108 of the surface fatalities were caused by railroad cars , 46 by machinery , and 58 by other causes . Most of those engaged in mining are still of the opinion that it is an extremely hazardous occupation and that it is practically impossible to operate without accidents ; however , students of safety in mining now believe that with the proper attention to accident prevention mining may be conducted with little , if any , greater accident rate than that of other supposedly hazardous industries . There is no mystery connected with accidents in mining ; reports show that the majority are due to two main causes , falls of roof and sides and haulage . Mining companies in Illinois , as well as in other States , have proved in the past few years that the hazards of mining , like those of other industries , can be controlled to a large extent and the mines operated with few if any accidents , provided a great enough effort is made by employer and worker . Although the past accident rate of Illinois may compare favorably with that of other mining States it is higher than it should be ; the fact that 6,673 men (an average of 133.46 per year) were killed in and around the mines of the State between 1882- and 1932 indicates that accident prevention should receive more consideration in the future than in the past .

Nov 1, 1934

In 2007, a total of 7,199 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 ? Sand and gravel mines were the largest mining sector, comprising 48.4% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Aug 1, 2009

By Laurance L. Oden

The Bureau of Mines studied three processes for preparing NaAl(OH)2C03) the intermediate compound which is calcined to produce alkalized alumina: (1) Mixing of Na2 C03 and of A12 (S04)3 solutions, (2) digestion of aluminum hydroxide in solutions of Na2C03 and NaHC03 at 90° C, and (3) addition of CO2 at 25° C to caustic solutions of aluminum to precipitate aluminum hydroxide followed by digestion at 90° C. The first process had the highest raw material consumption and washing requirements, and successful application of process 2 depended upon the availability of active aluminum hydroxide. Process 3 was the most effective, considering both process technology and raw material requirements. Procedures were also investigated for washing, filtering, drying, and calcining precipitates. Analytical methods included X-ray diffraction, atomic absorption spectroscopy, differential thermal analysis, and thermogravimetric analysis.

Jan 1, 1969

By Walter D. Holland

This study was undertaken to determine miners' breathing zone concentrations of diesel exhaust components, to investigate any relationships between these concentrations and vehicle type, the presence of emission controls, vehicle usage, and ventilation conditions, and to make recommendations for monitoring and ventilation requirements. Twenty-four mines including two con l mines were surveyed. Sampling was done for CON, NON, SOx, PNA, aldehydes, and particulates. hi most mines, concentrations of at least one contaminant exceeded one half the standard or TLV. The concentrations of gases arc probably sufficiently reduced by a minimum air velocity of 50 fpm. A sufficient reduction of particulate concentrations may require as high as 400 fpm air velocity. Vehicle age, type, or usage appear to have little or no effect on contaminant concentrations. PNA levels were below detection limits in all but a very few samples. Minimum requirements for routine monitoring should include formaldehyde, COx, NO2. It is further recommended that better definition of the minimum ventilation requirement be obtained.

Jan 1, 1978

By David A. Lipton

In 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources in the Carrizo Gorge Wilderness Study Area (WSA). The 14,571-acre WSA, located 42 miles east of El Centro, CA, is underlain primarily by Mesozoic granitic rocks and pre-Cretaceous metasedimentary rocks. Six prospects were found within the WSA and two mines are adjacent to it. Mineral deposits within the WSA have had insufficient development and rock exposures for calculating resources. The WSA contains no identified mineral resources; however, further exploration may disclose gem quality minerals. Two mines adjacent to the WSA, the Pack Rat and Beebe Hole, have produced gem quality kunzite and aquamarine from pegmatite dikes. According to the owners, a significant amount of gem minerals have been mined here in the last decade. Based on past production and the characteristic minerals indicating gem-bearing pockets, additional pockets are likely. Similar pegmatite dikes occur from Mt. Tule to Carrizo Gorge and may contain gem-bearing pockets. Pegmatite dikes also occur in the WSA near Rockhouse Canyon, but contained few of the mineral associations indicative of gem-bearing pockets. Manganese occurrences north of the Beebe Hole and Packrat Mines and within the WSA contain low concentrations of manganese. Significant sand and gravel were not identified. There is no evidence of deposits of oil and gas, or geothermal energy.

Jan 1, 1985

By Russell. Paul L.

"INTRODUCTION Preliminary reports by Bureau of Mines engineers 3/ and by the Federal Geological Survey 4/ suggested that exploration would discover substantial reserves of minable ore in the Contact mine, Grant County, New Mexico. During February and March 1943, a sampling program was conducted on this property under the direction of the author. This was art of a general survey of the manganese districts of southwestern New Mexico.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as practicable soon as after its conclusion. The Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocer, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. S. Dean, assistant director. With respect to this report, special acknowledgment is due to C. H. Johnson, district engineer for New Mexico, and E. D. Gardner, regional engineer, and his staff, of the Central Region of the Bureau of Mines at the time of this work in 1943; also to Kenworthy, metallurgist at the Rolla. Mo., Laboratory of the Bureau of Mines, for work on beneficietion of the ore, and Sherman K. Neuschel, geologist of the Federal Geological Survey, for assistance in interpreting geological data at the project."

Oct 1, 1946