Search Documents

By R. A. Pallanch

This paper, which describes the milling practice at the Midvale concentrator, is one of a series being prepared by the Bureau of Mines. The Midvale concentrator, a custom lead-zinc selective flotation plant, is in Salt Lake County, Utah, on a flat site several hundred yards east of the Jordan River and about 200 yards south of the Denver & Rio Grande Western Railroad tracks leading to Bingham Canyon. The site is at an elevation of about 50 feet above the river, the highest available location, thus allowing maximum storage of tailings.

Jan 1, 1931

By R. Blickensderfer

Several thin film absorber stacks with spectrally selective characteristics were developed by the Bureau of Mines. The stacks consisted of a silicon thick film or a zirconium compound thin film on a reflective thin film of silver. The zirconium absorber films, with the general formula ZrCxOyNz, were prepared by reactively sputtering zirconium or zirconium carbide in argon with small amounts of oxygen, nitrogen, or both, or by oxidizing zirconium films in air. A few similar types of films were prepared from titanium. The short-wave absorptance over the solar spectrum, a(s), and thermal emittance at 600 K, e(600 K), of the solar absorber stacks were calculated from room-temperature reflectance data. The values of a(s) ranged from 0.47 to 0.93, e(600 K) from 0.49 to 0.034, and the ratio a(s)/e(600 K) from 1.7 to 34. The specimen with the best combination of properties, a ZrNx-Ag stack, had a solar absorptance a(s) of 0.85 and a ratio, a(s)/e(600 K), of 24. The effect of film thickness and composition on spectral selectivity was determined. An emissometer for measuring normal total emittance up to 800 K and a method for determining a (s), e(T) (hemispherical), and a(s)/e(T) using simulated solar radiation are described. A calorimetric method for measuring a(s) and e(T) (hemispherical) at elevated temperature is also described. Measurements made on several specimens agreed favorably with calculated values.

Jan 1, 1976

By J. P. Morris

The Bureau of Mines investigated the mechanics of fuming of iron-carbon melts during top-blowing with oxygen. Melts weighing 45 lb were prepared in an induction furnace and blown with oxygen by means of water-cooled lances. The rate of fuming was measured and correlated with the operating variables. The data showed that the primary cause of fuming was a boil at the bath surface in the impingement zone of the oxygen jet. Nucleation of the carbon monoxide bubbles producing the boil was apparently brought about by the precipitation of an oxide phase. The actual fuming mechanism involved partial oxidation and vaporization of bubble films and fine metal spray generated by the bursting of the bubbles. Bubbles that formed outside the impingement zone produced little fume. The distribution of trace elements between the metal and fume strongly indicated that the fume contained fine spray particles as well as particles that had condensed from vapor. The rate of fuming was found to be proportional to the carbon content of the metal) the concentration of oxygen in the jet) and the bath temperature) provided that a continuous boil occurred. In the absence of a boil) very little fume was produced.

Jan 1, 1967

By A. L. Engel

The Stayton Mining District in San Benito County, Calif., near Hollister, includes several square miles with many occurrences of antimony ore. The sample submitted for the test described in this paper came from a vein said to have been traced and sampled for 5,000 feet on the surface, 1,500 feet carrying 2-1/2 to 3 percent antimony and the remainder 1/2 to 2 percent. Thirty thousand tons 'With a content of 3 percent antimony are said to be blocked out. A drift of 200 feet on the vein has shown ore containing 4.2 percent antimony. The present sample assayed 3.8 percent. Previous flotation investigation of this are resulted in a recovery of only 71.6 percent in concentrates containing 56.8 percent Sb. It was desired to develop a method of treatment that would give better results. The antimony in the sample occurred as the mineral stibnite, Sb2S3, antimony sulfide.

Jan 1, 1949

By L. E. Schultze

The Bureau of Mines devised a technique to recover a Zn-Pb concen-trate from a geothermal brine. More than 99 pct of the Zn and Ph was precipitated by treating the brine with H2S and controlling the pH with lime. Recycle of the sulfide precipitates increased crystal size and resulted in easily filterable products. A typical sulfide precipitate contained 53 pct ZnS, 8 pet PbS, 24 pct MnS, and 15 pct FeS. Addition of sulfide as FeS or CaS was not effective in precipitating Zn and Pb, but Zn in the brine was selectively removed with a strongly basic ion-exchange resin. A proposed flowsheet for metals recovery is discussed.

Jan 1, 1985

By R. V. Ramani, S. Shankar

"Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant (Shankar and Ramani, 1991 ). Therefore, as part of the Respirable Dust Center's ongoing research, the following three-part study was undertaken:• a study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities;• a study of the same in the Lake Lynn Laboratory Mine of the USBM with both air flow and walking by personnel causing re-entrainment; and• the mathematical modeling and computer simulation of the re-entrainment phenomenon.In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory mine are presented. Comparing the results from the two studies,it was observed that increasing the air velocity increased the rate of re-entrainment ( Shankar and Ramani, I 994a) and the rate of re-entrainment decreased with the time of exposure of the source dust to the flowing air. In addition, when the source dust was composed of particles of different sizes, the airborne dust concentrations due to re-entrainment were higher than when the source dust was composed of particles of the same size. The contribution of airborne dust concentration due to air flow was negligible compared to the contribution due to walking. IntroductionIn underground coal mines, dust is produced primarily during the process of mining and during such activities as pillar spall, loading, belt transfer and roof fall. The generated dust is entrained and then collects on surfaces through dispersion, diffusion and eventual deposition. Removal forces, such as flowing ventilation air or turbulence caused by walking and moving vehicles, can re-entrain the deposited dust (Hall, 1955). A portion of the re-entrained dust remains airborne and increases the concentration of airborne dust in mine airways.The presence of airborne coal dust in mine airways in large concentrations can be hazardous. Health effects include coal workers' pneumoconiosis (CWP) and silicosis, and it can be a nuisance affecting visibility. In addition, as is common during methane explosions, if the concentration of airborne coal dust becomes significant, there could be a coal-dust explosion (Singer, Cook and Grumer, 1972; Singer, Harris and Grumer, 1974; Edwards and Ford, 1988). Through concerned research efforts over the last decade, significantprogress has been made in reducing the airborne dust concentration in mine atmospheres. However, secondary sources, such as re-entrainment, have not been studied in-depth. It is important to understand the phenomenon of re-entrainment and its potential contribution to the airborne dust concentration in mine airways for further decreasing airborne dust hazards in mines."

Dec 1, 1996

By Constantine C. Popoff

"INTRODUCTION AND SUMMARYDuring 1946 several high-grade limestone deposits in western Washington were examined by the Bureau of Mines. This report presents the data obtained from investigation of the Sauk Mountain deposits in east-central Skagit County, Washington.The investigation consisted of transit and topcgraphic surveys and sampling. The areas selected for sampling were first cleaned by blasting; channel samples up to 40 pounds were cut where practical. Chip samples averaging 30 pounds were taken where channel samples could not be cut. A total of 21 samples in the Sauk Mountain area were taken and. analysed. The locations of the samples are shown in figures 2 and 4, and the analyses are listed in tables 1 and 2. This investigation is a part of a long-range program of general investigation of mineral resources for future industrial development of the Pacific Northwest. The Sauk Mountain deposits were investigated for the purpose of disclosing now sources of high-purity limestone, which could be mined and shipped at low cost to Seattle and other industrial cities in the Pacific Northwest."

Oct 1, 1948

By Robert J. Anderso

Few elements have received more attention and developed greater interest in the last ten years than titanium. The substantially pure metal has been din...ie. cult to isolate, and so far has been little employed oommercially, but the use af alloys and chemical compounds of titanium has increased markedly in recent years. The earlier attempts at preparing pure titanium resulted in various impure forme which, from their metallic appearance, were always mistaken for the metal. Hunter in 1910 isolated pure titanium by the reduction of titanium tetrachloride with sodium. This brief statement is issued by the Bureau of Mines in response to numerous inquiries which have been received concerning titanium. More complete in. formation on the metal may be had by consulting the referenpes appended. The Literature is voluminous and only the more important references are Riven. It has been drawn upon freely in preparing this report; also information was supplied by M. g. Hunter, Arthur Braid, M 1. Schmid, C. M. Johnson, N. B. Hoffman, and de Courny Browne. The pioneer investigator in titanium is A. IL Rossi.

Oct 1, 1922

By C. L. Klingman

The Bureau of Mines tested eight commercially available, activated charcoals experimentally to compare the following characteristics: capacity for adsorption of nitrogen at 77° K and 170 atmospheres' pressure, surface area, carbon tetrachloride adsorption capacity, hardness, and density. The nitrogen adsorption test was devised to simulate plant conditions occurring in the final step of purification in Bureau helium faciliti.es. The remaining tests were patterned after empirical acceptance tests that are widely used throughout the adsorbent industry. Surface area and carbon tetrachloride adsorption correlated well with nitrogen adsorption. The samples with low density generally had better adsorption qualities than those of higher density. The carbon tetrachloride test appeared to be the most practical for selecting a charcoal to be purchased, but an attrition, or hardness test should also be run to be sure the charcoal will not crumble in use.

Jan 1, 1966

By T. I. Weston

This is one of a series of papers being prepared for and published by the United States Bureau of Mines, describing mining and milling methods and costs at crushed-stone plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized' tat publication of total production costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. However, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no mis-understanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance-of F. W. Horton, mining engineer, United States Bureau of Mines, in the preparation of this paper.

Jan 1, 1933

By John A. Johnson

The purpose of this report is to clarify the interpretation of some phases of previous progress reports5/ on the use or omission of stemming that have been brought to the attention of the authors by readers. As the stemming problem was approached from an entirely disinterested viewpoint and the data were presented impartially, results of investigations published in previous reports5/ were obtained under a definite set of conditions and procedure, and they may of may not be duplicated under different conditions and procedure in actual mining practice. Final conclusions regarding the use or omission of stemming in blasting have not been reached pending completion of all aspects of this investigation.

Jan 1, 1942

The contractor examined L.T. White's Patent No. 3524680 and, finding it in need of engineering refinements, proceeded with a conceptual design of a variable wall mining machine. The contractor then proceeded to assess the feasibility of the variable wall mining machine measured against the criteria specified by the U.S. Bureau of Mines. The feasibility was judged from a physical aspect, a health and safety aspect, and an economic aspect. The Variable Wall Mining Machine was judged to be feasible on all three aspects provided that certain specified practices were adopted. Description The specifications and design and performance parameters of the Variable Wall Mining System as conceptualized are summarized in Tables I and II. The system consists of a side-cutting auger operating in a string of identical 12 ft. sections, along a 500 ft. retreating longwall face. In addition to the 41 identical sections, there is a special drive and discharge section at the head gate.

Jan 1, 2012

By John A. Johnson

The purpose of this report is to clarify the interpretation of some phases of previous progress reports5/ on the use or omission of stemming that have been brought to the attention of the authors by readers. As the stemming problem was approached from an entirely disinterested viewpoint and the data were presented impartially, results of investigations published in previous reports5/ were obtained under a definite set of conditions and procedure, and they may of may not be duplicated under different conditions and procedure in actual mining practice. Final conclusions regarding the use or omission of stemming in blasting have not been reached pending completion of all aspects of this investigation.

Jan 1, 1942

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a part of the 21,296-acre Million Hills Wilderness Study Area (NV-050-233) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, about 46 miles south of Mesquite, NV. The area is on the east edge of the Gold Butte mining district and has had minor production of copper and zinc from the Azure Ridge mine in the early 1900's. Assessment work was being done on the Esperanta claims, which covers the mine workings, in March 1987.

Jan 1, 1988

By Jennifer S. Riefenberg

The U.S. Bureau of Mines conducts basic and applied research related to predicting, eliminating, and/or controlling rock bursts in underground hard-rock mines and coal bumps in underground coal mines. An important element in this research is the development of a reliable and efficient microseismic source location technique. This report presents the results of a Bureau study to develop and evaluate a new algorithm to locate microseismic events based on the Simplex method, a powerful linear programming technique. The technique was tested on both field data and simulated data. Microseismic event source locations obtained with this new Simplex-based algorithm were shown to have less error than those locations obtained using a least squares method. It was concluded that the Simplex approach to source location of microseismic events can be used effectively in microseismic monitoring.

Jan 1, 1989

By J. B. Zadra, S. M. Shelton, R. B. Fisher, M. M. Fine

"INTRODUCTION An extensive test program is in progress by the Bureau of Mines to determine ways and means of recovering ferromanganese ore 5/ from the widespread domestic manganese and manganiferous iron deposits.Samples were received from the Stance property in southwestern Virginia, 12 miles northwest of Stoney Gap, in Bland County.The Stange mine is situated on the crest of Flat Top Mountain and is developed by open-cuts extending over several acres. The manganese deposit occurs in the Oriskany sandstone largely as a replacement of the sandstone, to some extent as breccia filling in the crusted parts of the sandstone, and as veins along joints, and bedding planes.The mine was first worked in 1917 and was operated during the war years. A long period of idleness was followed by intermittent operations in recent years. A small log-washing plant, consisting of a 20-foot log washer, was operated 1-1/4 miles northwest of the mine. The log-washer concentrates were crushed to minus- 1/2 inch and then washed in a second log washer to remove as much of the siliceous sandstone as possible. According to a communication from the operator, the double-washed concentrates were jigged and the jig concentrates marketed without further beneficiation."

Apr 1, 1942

This publication summarizes, for potential contractors and other interested parties, the proposed research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1977 (October 1, 1976-September 30, 1977) under its Advancing Coal Mining Technology program. The objective of these projects is to provide an ordered and sequenced series of advances toward the overall goal of providing the system technology required to increase the productivity of the coal mining process.

Jan 1, 1977

By R. J. Heemstra

A method was developed for calibrating photographic emulsions and retrieving working curves for emission spectrography. The values obtained from a digital readout or a recorder chart of a comparator-microphotometer are converted to light intensity values using an emulsion characteristic curve derived from a quartic polynomial preliminary curve. The characteristic curve, consisting of Seidel transform versus the logarithm of intensity, is split into two cubic polynomials at the zero value of the transform, resulting in eight emulsion calibration coefficients. These methods allow use of the calibration curves even at very small and very high intensities, thus extending the range of analysis. Use of a small computer allows rapid calculations. A computer program was written to formulate, code, and file each working curve along with its statistical error. Proper coding of the input data permits the direct printout of the concentration of the elements under investigation.

Jan 1, 1970

By M. C. McCall

When electric current of any appreciable magnitude flows from a power line into the earth, a change sometimes takes place in the conditions of resistivity immediately surrounding the electrode or medium of contact. If the conducting medium is composed of moist earth or clay the effect is to increase rapidly the resistance. If the conducting medium is coal or a coal bed, the effect is one of slowly decreasing resistance as the coal is carbonized, If, however, the flow of current is not enough to carbonize the coal, it will dry slowly, with a resultant increase in resistance. Measuring ground resistance, or impedance, with conventional commercial ground testers does not always indicate the current that will flow in the earth circuit from a direct-current or an alternating-current power circuit. The exact reason for this has not been determined however, it is thought to be due to the comparatively minute currents used for such testing. A typical ground, tester used by the authors for this work indicated a maximum current of 25 milli-amperes. The frequency of this testing current also has an effect on the readings in all probability. While the possibilities of the effects of varying frequencies has by no means been fully explored in this investigation, there are very definite indications that the impedance of a circuit through a section of earth will vary in some inverse relationship to the frequency of the applied voltages. This is evident at ordinary power-line frequencies ns well as at higher frequencies up to 200 kilocycles, which was the highest frequency available for tests in this investigation. This report is written in the hope that it will stimulate further investigation of the possibilities suggested for communication and the development of safety devices for increased electrical safety in coal mining.

Jan 1, 1952

By T. E. Ackman

Scale inhibitors and slow-release polymers were tested by the Bureau of Mines at mine drainage treatment facilities. The scale inhibitors were investigated to determine their effectiveness in controlling gypsum (CaSO4) scale; the polymers were investigated to determine their effectiveness for increasing settling rates of suspended iron hydroxide. Two types of scale inhibitors were tested at a site having a severe CaSO4 scaling problem. Both proved to be effective in controlling scale formation; in addition, one caused the dissolution of CaSO4 deposits. Slow-release polymers were tested at three mine drainage treatment facilities. These gelatinous polymeric flocculants were found to be convenient and easy to use, but only effective when pH could be controlled.

Jan 1, 1984