Search Documents

By E. A. Mihok

A pilot plant for treating mine drainage by neutralization with limestone was designed, fabricated, and operated by the Bureau of Mines. The process consists of (1) producing a very fine (minus 400-mesh) limestone slurry, (2) mixing the slurry with the mine water, (3) aerating the resulting mixture to remove carbon dioxide and precipitate iron, and (4) separating the solids from the liquid by sedimentation. A mine discharge of pH 2.8, containing 1,700 ppm total acidity, 36 ppm ferrous iron, and 360 ppm total iron, was treated at rates from 300 to 400 gpm. The treated water ultimately reached a pH of 7.4 and contained no detectable iron. The resulting sludge compacted to approximately one-third the volume of sludge from mine water neutralized with lime. The advantages of the limestone process, compared with the conventional lime process are as follows: Widespread distribution and lower cost of run-of-mine, indigenous limestone; simplicity of plant design; reduced hazards and plant operating and maintenance costs accruing from the use of a less reactive chemical agent; higher solids concentration of the precipitated sludge; and no deleterious effect caused by accidental overtreatment. While total process costs could not be determined, it is conservatively estimated that the cost of treating mine water by the limestone process is one-third to one-half the cost of the lime process, depending on the characteristics of the water to be treated and the availability and quality of limestone used.

Jan 1, 1968

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By W. H. Coghill, F. D. DeVaney

"Introduction Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with no many ""inflection points"" and ""counterflexures"" that they obscure the issue.Some of the investigators have neglected the very essence of the problem, namely, the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration.Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.Grindability Characteristics When the ores are being studied the information sought is grindability characteristics (grain-size distribution) and the grindability (work required to produce new surface) of a group of ores.When the study is of the machines, several machines are used for a given ore or given types of ores, and the grinding performances of the machines are compared by a grain-size study.Table 1 gives the grindability characteristics and grindability of six substances, one of which is coal. The substances are arranged from left to right in progressing order of tons per horsepower-hour. Curves and graphs are not needed for elucidation. The secret of the ease of interpretation is the order mentioned and the similarity of the sizing analyses. Power records must be complete in grinding studies.The grinding device was a ball, plunger, and mortar called the drop weight.' It may be used to advantage when the amount of material to be tested is too small for the orthodox machines.The upper part of table 1 shows the grindability characteristics by the cumulative-sizing analyses. Note how closely the percentage weights agree for a given sieve size. The lower part shows the grindability in terms defined elsewhere. The present paper should be read in conjunction with that paper."

Jun 1, 1934

By Paul M. Tyler

Hafnium appears to be among the more abundant of the newly discovered elements . Though quite widely distributed in nature , its compounds chemically so resembled those of zirconium , its sister element , that it escaped detection until 1923 , when Coster and Hevesy announced the discovery of the element , to which they gave the name of " hafnium " , from Hafniae , the Latin name for Copenhagen , where their research work was performed . Hafnium has so far been found only as a minor constituent of zirconium minerals . Zirconium as an element was discovered more than 140 years ago , but only a few unimportant uses were found for the metal or its compounds until some 18 years ago ; it is still classed among the rarer commercial metals . It is not surprising , therefore , that hafnium has not yet found a definite place for itself in industry . Nevertheless it has commanded a considerable interest among scientists ; and in 1930 some 70 grams of perfectly pure oxide of hafnium were prepared in Europe . A commercial future for hafnium is already glimpsed in the radio industry , and its high melting point and electronic emissivity have already led to the taking out of patents for its use in radio tubes and incandescent electric lamp filaments and for the cathode surfaces of devices such as X- ray tubes and rectifiers .

Apr 1, 1931

By John L. Edwards, Anthony T. Iannacchione

There has been a persistent need to forecast roof falls so that miner’s exposure to hazardous underground environments can be minimized. Several monitoring techniques have been developed and are used today with varying levels of acceptance in the mining industry. This paper examines the potential for monitoring microseismic emissions activity as a means of forecasting roof falls. The use of this activity to forecast roof falls has drawn only limited attention, resulting in a lack of published field performance data. This deficiency is being partially addressed by analyzing data obtained during longwall mining at Moonee Colliery in 1998. The Moonee data base contains a wealth of information concerning roof fall forecast parameters and the seismic alarm criteria used to develop these forecasts. Four seismic alarm criteria were developed and used by Moonee with varying degrees of success. Roof falls were forecasted 73% of the time with average forecast times of 54 minutes. Ninety percent of the predicted roof falls had a warning time, i.e., the time between warning and roof fall event, of greater than 1 minute. The fraction of forecasted roof falls decayed logarithmically as a function of warning time, until only 20% of events were predicted more than 100 minutes prior to roof falls. False alarms occurred in 50% of the warnings. Many of the false alarms were quickly followed by a cessation in mining which could have temporarily halted the on-going failure process. If mining had continued immediately after the false alarms, a roof fall may have occurred soon after. The microseismic activity collected from Moonee Colliery demonstrates that techniques to forecast roof rock instabilities in underground mines are possible.

The 53 countries that constituted Africa in 1992 accounted for a significant portion of total world output of a number of mineral commodities. However, the continent's total output for a number of major mineral commodities declined relative to the volume produced during 1991. (See tables 1 and 2.) The most conspicuous declines in mineral production from 1991 to 1992 were for cobalt and copper (declines of 28.6 % and 23.4 %, respectively), which could be partially attributed to mining and metal processing difficulties caused by political and economic disruptions in Zaire and for uranium (12 % drop), for which much of the continental production decline was ascribed to Namibian cutbacks in response to lower world prices. The severe regional drought also adversely affected the mineral industry in a number of sub-Saharan nations.

Jan 1, 1994

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

"INTRODUCTION The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment, and details of the procedure are given in A.S.T.M. Designation: D271-44 5/. According to the specifications, the following features should be incorporated in the equipment used:1. Oven must have uniform temperature in all parts.2. Oven must be constructed with minimum of air space.3. Oven must have means of changing the air two to four times per minute.4. Air must be dried over sulfuric acid (sp. gr. 1.84).The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general and of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.The semi-automatic moisture tester manufactured by the Brabender Corp. has proved itself in many industrial processes where the rapid estimation of moisture is of vital importance. With the approval of A. C. Fieldner, chairman, A.S.T.M. Committee D-5, and through the courtesy of Lowell Malan, chief chemist, United Electric Coal Companies, who loaned the tester, tests were made to determine the feasibility of using this instrument to determine the moisture in coal."

Jun 1, 1948

By V. Castranova, K. VanDyke

"INTRODUCTION A soluble mediator has been described which is released from activated rabbit leukocytes and induces histamine secretion from rabbit platelets (Barbaro and Zvaifler, 1966; Siraganian and Osler, 1971). This factor has been isolated, characterized and named platelet activating factor, PAF (Bcnveniste et. al., 1972). PAF has since been chemically identified as l-0-alkyl-2-acetyl-sn-glyceryl-3-phosphocholine (Benveniste et. al., 1979; Demopoulous et. al., 1979).PAF is a lipid mediator of broad biological activity. It causes smooth muscle contraction, contraction of lung tissue and decreased FEV 1; while enhancing capillary permeability thus causing edema (Pinkard, 1983). In addition, PAF is a chemoattractant and can lead to inflammation.PAF has been reported to stimulate the release of lysosomal enzymes, leukotriene B,, and lipid metabolites from neutrophils (Smith et. al., 1983; Shaw et. al., 1981; Lin et. al., 1982; O'Flaherty et. al., 1984). The objective of the present investigation was to further characterize PAP-induced stimulation of granulocytes and to develop a bioassay, i.e. chemiluminescence, for screening PAF receptor antagonists and inhibitors of PAP-induced activation of granulocytes. The possible use of the chemiluminescence assay to monitor PAF synthesis by human granulocytes is also described.METHODSBlood was drawn from healthy volunteers into a blood storage bag containing CPD anticoagulant. Granulocytes were partially purified by dextran sedimentation and further purified by centrifugal elutriation as described previously (Jones et. al., 1980). Granulocytes obtained by this procedure were approximately 95 percent pure. The number of granulocytes in this preparation was determined using an electronic cell counter (Coulter Model Z1, Coulter Instrument Co., Hialeah, FL). Isolated granulocytes were used to monitor membrane potential, hydrogen peroxide and superoxide release, oxygen consumption, calcium uptake and, in some cases, chemiluminescence. Studies of PAF receptor antagonists were conducted using neutrophils isolated by density centrifugation. Briefly, blood was layered onto Mono-Poly-Resolving Medium (Flow Laboratories, McLean, VA) and centrifuged at 22 °C and 300 g for 30 min. Neutrophils collected from the second band of this gradient were at least 90 percent pure."

Jan 1, 1989

By J. G. Donaldson

A bench-scale method for recovering lead and zinc from slimes and mill tailings from the Tri-State District of Missouri, Oklahoma, and Kansas was developed by the Bureau of Mines. Dilute hydrochloric acid, containing sodium chloride, and chlorine gas were used to decompose the mineral constituents. Lead was electrolyzed from the pregnant acid solution, and zinc was precipitated from the depleted electrolyte by neutralization with lime. Up to 98 percent of the lead was recovered in an impure lead electro- deposit assaying approximately 85 percent lead. Zinc recoveries up to 90 percent of the total were attained in a precipitate assaying approximately 40 percent zinc.

Jan 1, 1963

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

By Jack C. White

The purpose of this Bureau of Mines research was to determine the technical feasibility of direct sulfuric acid digestion of Florida land-pebble phosphate matrix. Preliminary tests in a continuous digestion circuit showed that 92 to 96 percent of the P2O5 contained in the matrix was extracted, while the P.05 concentration in the product acid ranged from 21 to 30 percent. The waste filter cake contained about 1 percent P205 and up to 18 percent water. These sandy compact filter cakes, comprised mostly of quartz and gypsum, appeared to be suitable for backfilling and reclamation of mined lands.

Jan 1, 1975

By Sidney Katell

This report, covering the period January 1965 through December 1965, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the seventh in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are From the following sources:

Jan 1, 1966

By Spencee L. Willett

A sand and gravel deposit exists in the Wildrose Canyon Wilderness Study Area (WSA), Out it is limited to local use because of the distance from major markets and resulting high transportation costs. The WSA has no identified metallic minerals, oil, gas or other energy related deposits. INTRODUCTION The WSA encompasses 17,366 acres (7,028 ha) in the Panamint Range, Inyo County, California. Access to the area is by State Route 190, approximately 45 miles (72.4 km) east of Lone Pine, California and 16 miles (26 km) southwest of Stovepipe Wells, California (fig. 1).

Jan 1, 1983

By J. H. Adkins

The goal of this program was to produce a set of baseline health and safety training materials that could be used by the metal/nonmetal mining industry to reduce injuries and to comply with federal training requirements. The materials developed are arranged in a two level outline format. The first level provides the title, course goals, background and topical outline while the second level provides a detailed outline of the course content. Visuals, designed to portray miners in a positive, attractive fashion, were done in simple line drawing so they would reproduce for handouts without loss of quality. Each of the required units in the Baseline Guides have one or more self-checks. These are designed to be suggestive of evaluation techniques the users can develop for themselves. An instructors guide and a mining terms glossary are included. In a second phase the program developed performance based training guides for Annual Retraining and Experienced New Hires in the Underground Salt Industry.

Jan 1, 1983

By John R. Hoskins

Uniaxial compressive strength of rock is usually determined in the laboratory from cylindrical samples that vary in diameter from 5/8 to 8 inches, using a spherically seated compression head of unspecified size. The Bureau of Mines conducted a series of tests on limestone, marble, sand-stone, granite, and plaster of paris to determine the influence of the spherical head sizes and the specimen diameters themselves on the uniaxial compressive strength. Cylindrical samples of several different diameters of each rock type, all having a length of twice their diameter, were prepared and broken using at least three different diameter spherical heads. Analysis of the data shows that spherical head size does not significantly affect the uniaxial compressive strength of cylindrical rock samples. However, the diameter of the rock specimens does significantly affect the uniaxial compressive strength. Within the range of specimen diameters tested, a coefficient of variation of 6.4 percent for plaster of paris can be attributed to the selection of specimen diameter alone. Similarly, a maximum coefficient of variation of 4.7 percent for the rock types tested can be attributed to the specimen diameter alone.

Jan 1, 1969

By M. Clair Smith

This report is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods, and costs at various open-pit mines in the United States. These reports have been prepared in cooperation with various mining companies. A similar program, conducted from 1928 to 1939, was generally conceded to have contributed to improving the efficiency of mining operations. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technological information on mining methods and practices. This report describes exploration, development, equipment, and mining by open-pit methods of the remainder of an ore body that had been previously worked by underground methods. The Tripp pit of the Consolidated Coppermines Corp. is located at Kimberly, Nev., a small mining company town having an elevation of 7,250 feet, 9 miles by road west of Ely, Nev. (fig. 1). The pit extends over the area formerly mined by underground methods from the Morris and Brooks shafts.

Jan 1, 1962

By T. F. Mitchell, Walter J. Long

"SUMMARYThis report is one of a series giving results of laboratory and pilot-plant investigations of the concentration of western manganese ores begun in December 1940. Data given summarize results of laboratory investigation of three samples of complex oxide manganese ores from the Madeline property, Lake View, and Victory claims, Clallam County (Olympic Peninsula), Wash. The samples represented an extremely intimate and complex association of manga¬nese oxide minerals with silica and iron.Owing to the complex nature of the ores, no effective concentration by ore-dressing methods was possible. No high-grade manganese concentrates were produced and the highest recovery at minimum accountable grade was only 55 percent on one of the ores tested.Since the Clallem County ores did not respond to ore-dressing methods, leaching processes were investigated, results of which are to be published in a separate report.INTRODUCTIONOre-beneficiation tests were conducted on three samples of manganese oxide ere from the Madeline, Lakeview, and Victory claims, Clallam County, Wash. The ores are extremely complex because of the unusually small size of manganese mineral particles, their mode of occurrence, and relationship to the gangue. None of the three ores was amenable to the production of high-grade manganese products by ore-dressing methods."

Dec 1, 1945

By E. P. Youngman

In the absence of any subsequent enactment of mining legislation, the Turkish mining law in effect in 1914, when Iraq became a British mandate, is still operative. The Constitution, or Organic Law, of Iraq, adopted by the Constituent Assembly on July 10, 1924, in articles 113 and 114, provides that:3 Ottoman en laws date and thao remained and lave pub- lished on or after that date and which have remained in force in Iraq u to the time of the publication of this law shall remain in force in Iraq' so far as circumstances permit, subject to any modi- fication or repeal in conformity with the proclamations, regula- tions, and laws referred to in the following article, and until they are altered or repealed by the legislative power or the High Court issues a decision rendering them null and void in accordance with the provisions of article 86. (Art. 113.) All proclamations, regulations, and laws by the Commander-in- Chief of His Britannic Majesty's Forces in Iraq, the Civil Commis- sioner, and the High Commissioner, and those issued by the Govern- ment of His Majesty King. Faisal, during the period between Novem- ber 5, 1914, and the date of the coming into force of this Consti- tution, shall be considered to be valid as from the date on which they came into force... (Art. 114.) 4 According to a German authority, it is the Turkish law of March 26, 1906, that, with a few modifications, is still in force. This law (similar to the French law of 1810) is discussed in a separate section of this paper.

Jan 1, 1933

By A. U. Miller

For many years Illinois has been one of the leading coal producers in the United States and as such its safety record has compared very well with the other large coal producing States , both in tons produced and millions of man -hours of exposure per fatal accident . ( See Table 25 in Bureau of Mines Bulletin 293. ) During the 10-year period from 1917 to 1926 , inclusive , the average production in the United States per fatal accident was 278 , 109 tons . The aver age for the State of Illinois for the same period was 409,249 tons . Illinois produced 450,464 tons per fatal accident, and in 1928 produced 390,630, tons , or an average of 419,721 tons for the 12- year period from 1917 to 1928 , inclusive . In 1927 During the year 1929 , the shipping mines of the State made a decided improvement in their record over any previous year . Table 1 shows the monthly production and the tons produced per fatal accident . During 1928 and 1929 safety work was actively carried on in Illinois . Safety meetings were held with mine officials , representatives of the State. De partment of Mines , and the United States Bureau of Mines . At these meetings mine hazards and accidents were discussed and remedies suggested for : their elimination in the future . It is believed that first - aid training was to a considerable extent instrumental in reducing accidents and in making the good safety records in Illinois during 1928 and 1929. During these years ( as well as in 1926 and 1927 to a somewhat less extont ) en intensive rirst-aid training campaign was con ducted in Illinois by the officials and members of the United Mine Workers of America , coal companies, State Department of Mines and Minerals , and the U. S. Bureau of Mines , Every first -aid class was made a safety meeting ; where accidents and general safety were discussed freely while teaching first aid. During this time , anproximately 25,000 persons were trained in first aid, and 17 coal companies were issued certificates for having 100 per cent of their employees. trained in first aid. Since January 1 , 1926 , more than 40,000 have received first -aid training in and around Illinois mines , and including those who received training previous to this date , it is believed that at least 90 per cent of the miners in Illinois have received first -aid training . This state ment is based on the fact that the labor turnover in Illinois is not large .

Apr 1, 1931