Search Documents

By H. R. Babitzke, H. Kato, R. E. Siemens, G. Asai

The purpose of this investigation was to develop a wide variety of columbium and tantalum alloys and to determine their suitability for use at elevated temperatures . Sixty - nine columbium and tantalum alloys were investigated . For this study , columbium was alloyed with two or more of the following : nium, tungsten , vanadium , titanium, and zirconium . Tantalum was alloyed with vanadium or hafnium, or hafnium and carbon . The fabricability was determined by an arbitrary procedure . Hardness measurements , elevated - temperature tensile properties , and oxidation- resistance studies were made . Of the alloys studied , Cb - 15 Hf - 5W, Cb - 15Hf - 5W- 10Ti , Cb - 15Hf - 10W- 10Ti , Cb - 10V - 5W, Ta - 30V , and Ta - 20 to 33Hf exhibited excellent high - temperature properties . These alloys were not only easy to fabricate , but they also had good oxidation resistance and excellent high- temperature strength .

Jan 1, 1964

Approximately half of all the fuel energy used in the United States is now pro-vided by oil and natural gas. A persistent and rapid growth in energy demand during the last 3 decades has been absorbed largely by the liquid and gaseous rather than solid fuels. In 1948 the energy provided by coal was substantially the same as in 1920. Meanwhile, the use of oil and natural gas each had increased fivefold. On a per capita basis, the change is more significant. Coal consumption has dropped from about 6 tons per person to 4-1/2 tons, while oil has increased from 4-1/3 barrels to 14-1/3, and natural gas from 7,500 cubic feet to about 35,000. These facts would have only academic interest if the United States had unlimited supplies of all fuels. However, while the Nation's reserves of coal are adequate to meet our needs for centuries, those of oil and natural gas appear limited. It is obvious, therefore, that the security of our liquid-fuel position would be greatly enhanced if the supply could be based in an increasing degree on solid fuels, such as coal/and oil shale, which make up more than 95 percent of our fuel reserves, instead of natural oil and gas. In addition, this would create new employment and help to stabilize the market for coal, which may be facing comparatively bleak prospects in the near future unless its position with respect to other fuels is improved.

Jan 1, 1950

By H. W. Sheffer

Technical and economic aspects of community refuse disposal systems and their effects on the environment are identified and described. Seven landfills and two incineration systems, located throughout the United States, are reviewed.

Jan 1, 1971

Comparative tests of four coals used industrially for coke production have been made by three laboratories of the Federal Bureau of Mines, each using its standard equipment and procedures for evaluating coal for coking. Two of the coals were blends used in the western and eastern sections of the United States, the third was a strongly coking coal widely used for producing coke in Alabama, and the fourth was a blend typical of those used for producing foundry coke in the Birmingham district. The coals used and the cokes produced from them covered a wide range of chemical and physical properties. The tests used at all three laboratories for determining the physical properties of the cokes were made according to ASTM (American Society for Testing Materials) methods. The excellent agreement found for the physical properties of the cokes indicated that, for the coals tested, the BM-AGA (Bureau of Mines-American Gas Association) 18-inch circular retort used at Pittsburgh, Pa" the 14-inch slot-type oven used at Denver, Colo., and the 17-inch slot-type oven used at Tuscaloosa, Ala., were substantially equivalent for evaluating coals for production of coke. Thus, added value is given to data obtained previously and independently at these three Bureau laboratories. INTRODUCTION Laboratory equipment to produce coke for evaluation has not been standardized by the industry. The results obtained with anyone design of equipment have been regarded as showing only the relative values of coal to produce coke of the requisite quality. Few systematic studies have been made to correlate results obtained in different types of equipment. Results of one, in which the Bureau of Mines participated, were published recently.2/ This

Jan 1, 1961

By Thomas M. Barczak

The U.S. Bureau of Mines has been conducting research to optimize the design and utilization of mine roof support systems. An objective of these efforts is to evaluate the mechanical and structural responses of various mine roof support systems under simulated load conditions in the Bureau's mine roof simulator. Underground studies are also made to evaluate the in situ behavior of support structures. The purpose of this report is to document practical applications for longwall face and gate road supports that have resulted from these studies. This report is not intended to be an all-inclusive manual on every aspect of support utilization, but it does provide a comprehensive assessment of practical considerations relating to the mechanical and structural behavior of these support systems. Forty-six recommendations are made to provide assistance to mine operators in the testing, selection, and utilization of longwall face and gate road supports. Many of these recommendations offer innovative solutions to everyday problems faced by mining personnel in the control of ground in longwall mining.

Jan 1, 1989

The Mateen deposit comprises two large spodumene-bearing pegmatite dikes that outcrop along the, side and crest of a hill overlooking 'Rill City in the southern Black Hills of South Dakota. The Bureau of Mines investigated the Mateen deposit as part of a comprehensive study of the lithium mineral-production possibilities in the Black Hills area. The work was undertaken during the second World War, when the demand for certain lithium salts and compounds exceeded the small productive capacity of the industry. During the course of the investigation, the Bureau of Mines took 61 large channel samples from surface trenches, 4 channel samples from a shaft, and 3 from the face of an open cut. In addition, 8 diamond core-drill holes were completed to investigate the attitude of one of the dikes at depth. Metallurgical tests were conducted by the Bureau of Mines to determine the feasibility of beneficiating spodumene-bearing ores from the Mateen dikes.

Jan 1, 1948

By R. S. Dewey

The purpose of this study was to assess the various aspects of public safety related to the thousands of abandoned or inactive underground mines found throughout Western Colorado. Review of available published mine inventories yielded data on over 8,000 abandoned underground mines. A random sample of 200 mines was then selected for field visits representative of mining activity in Colorado. Inspections of the openings at two hundred abandoned underground mines were performed recording descriptive information regarding the opening, the mine site, the surrounding area, the primary opening hazard, secondary hazards related to structures or dumps, other openings to the same mi ne, available construction materials, possible safeguard methods, and any special observations such as apparent activity, previous closure attempts, environmental constraints on construction, and access problems. Of the 200 mines visited, twenty mine openings representative of varying geologic, environ-mental, access, and mining conditions were selected for detailed low-cost safeguard application. Description of these safeguards is presented in narrative, itemized labor-materials equipment tabulations, and illustrations. Research into the regulations of mine closure and safeguards was also undertaken to determine jurisdiction of public lands. Recommendations were suggested to improve the awareness and ability to continue this program into an implementation stage.

Jan 1, 1980

By Michael C. Horn

The 61,470-acre Lick Creek Roadless Study Area is in the western Salmon River Mountains, centered 12 miles northeast from McCall, ID. U.S. Bureau of Mines personnel examined the roadless area in 1984. There is no recorded mineral production from the study area and no current mineral-related activity was observed. The roadless area is underlain by granitic rocks of the Idaho batholith. Pegmatite dikes and aplite dikes are present locally. Sampling indicates these rocks are not mineralized. No mineral resources were identified. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of federal lands recommended for wilderness, as required by The Wilderness Act of 1964. The USBM examines and evaluates individual mines, claims, prospects, and mineralized zones; USGS conducts broader geological, geochemical, and geophysical surveys. Such data helps Congress and other federal agencies make decisions affecting the use of public lands.

Jan 1, 1986

By S. L. May

Procedures for separating columbium and tantalum have been developed by the Bureau of Mines as part of a broad research program on the utilization of low-grade ores of columbium and tantalum, Columbium and tantalum compounds of greater than 99 percent purity have been obtained by application of the solvent extraction separation system: Hydrofluoric acid-sulfuric acid-methyl iso-butyl ketone. This system is unique in that it not only separates columbium from tantalum, but also separates these two metals from other metallic impurities. The system is effective for separating the metals irrespective of the tantalum and columbium ratio of the starting materials. Investigations in which the spent feed obtained from the initial coextraction step was recycled to the system indicated that efficiency was increased, and cost was reduced without impairing product purity. Continuous tests demonstrated that this solvent extraction system could be used in large-scale equipment without loss in efficiency or in purity of products. The separation of columbium and tantalum has been difficult because of the similarity in their chemical bahavior. Many methods have been proposed for separating these two elements, but most methods either did not achieve satisfactory separation or were tedious and time consuming. The Marignac process (3, 4)4 developed in 1866 was the only method used commercially until recently. This separation procedure is based on the difference in solubility in aqueous solution of potassium tantalum fluoride and potassium columbium oxyfluoride. Current commercial practice appears to favor solvent extraction as a method for separating tantalum from columbium (1). Several efficient methods for separating columbium from tantalum by solvent extraction (2, 9, 8) were reported earlier from this laboratory.

Jan 1, 1961

By R. M. Jimeson

Pressure-drop measurements through beds of granular iron, lathe turnings, steel wool, and parallel-plate assemblies were made at linear velocity and gas-density ranges expected in the Fischer-Tropsch hot gas recycle process.4/ Equations relating pressure drop, linear velocity, gas density, and bed porosity were derived. The results indicate that the exothermic heat of reaction can be removed at a lower cost by using catalyst beds with high porosity. INTRODUCTION The Fischer-Tropsch hot-gas-recycle process requires a catalyst offering low resistance to gas flow as one condition to economic feasibility. Conventional granular or spherical catalysts used during early development of the process in Germany did not meet this requirement. Large pressure drops across these beds made the cost of recirculating the gas excessive. The Federal Bureau of Mines is investigating the process by using novel and unusual catalysts that offer little resistance to gas flow. Pressure-drop measurements across these types of catalyst beds are discussed in this report.

Jan 1, 1959

By R. T. C. Rasmussen

"INTRODUCTION This is the second report of investigations describing tests in full-scale commercial heats of steel-using electrolytic manganese having a purity of about 99.95 percent, produced in the Bureau's pilot plant at Boulder City, Nev. The first report dealt with tests in cooperation with two companies can the use,of electrolytic manganese in the manufacture of stainless steel. 3/ Plans aril cost estimates for reasonably large commercial, electrolytic plants based upon pilot-plant experience, as well as the comments of a number of concerns where electrolytic manganese has been tried, are contained in another publication.4/ The tests in cooperation with industry are part of the Bureau of Mines program of investigations of methods of utilizing low-grade domestic manganese ores, thereby the United States leas dependent upon foreign sources of manganese for metallurgical use. The Boulder City pilot plant already has demonstrated the feasibility of producing electrolytic manganese from several of the most important reserves of low-grade manganese ore. As the ferromanganese normally used by the steel industry represents the bulk of the Nation's manganese requirements, the usefulness and possi¬ble advantages of electrolytic manganese in the manufacture of steel must be established if electrowinning from domestic ores is to become an important factor of manganese supply.Preliminary arrangements for the cooperative tests at the Atlas Steel Casting Co., Buffalo,. N. Y., were made with E. L. Altenburg, vice president and general manager of the company, by A. A. Dow. 5/ The data on the tests at the Atlas plant presented herein are based upon reports of E. L. Altenburg and information obtained by the author during a visit to the plant to observe the initial trial heats with electrolytic manganese in the open-hearth and the electric furnace."

Nov 1, 1945

By S. P. Kinney, P. H. Royster, T. L. Joseph

"The study described in this paper, on the reactions in an iron blast furnace, is part of the investigation being conducted by the Bureau of Mines on combustion of coke and the reduction of iron oxides in the blast furnace. Previous study of the combustion zone of the iron blast furnace, by means of a series of as samples taken through the tuyeres across the hearths of 13 blast furnaces, showed that the combustion of the coke in the blast-furnace hearth is complete at a distance of 32 to 40 inches from the nose of the tuyere, measured horizontally toward the center of the furnace. The results of this previous work are sum¬marized in the curves shown in figure 1, where it will be noted that practically all of the oxygen disappears at a distance of approximately 30 inches from the nose of the tuyere.In order to determine the height at which oxygen is found in a vertical direction above the tuyeres - it had been suggested that the combustion zone turned upward near the tuyere and to obtain comparisons with the samples taken at the Bureau of Mines experimental6 (5-ton) blast-furnace at Minneapolis, the Bureau extended the gas sampling on a commercial furnace to a number of planes between the tuyere level and the stock line. The sampling was conducted on a 300-ton furnace, making foundry iron, operated by the Central Iron and Coal Co., at Holt, Ala. The furnace was smelting Southern red and brown ores and nodules from pyrite sinter. Figure 3 is a vertical section of the furnace showing the six planes sampled."

Apr 1, 1926

By W. W. Agey

Under terms of cooperative agreements, the Federal Bureau of Mines Inter-mountain Experiment Station assisted the General Services Administration (GSA) in operating the manganese-ore purchasing depots at Deming. N. Mex., and Wenden, Ariz. A resident metallurgist stationed at the depots directed sampling of the ore lots for assaying, took samples for amenability testing, calculated acceptances for payments to shippers, and served as technical adviser to the depot manager. The Intermountain Experiment Station at Salt Lake City, Utah, tested the amenability of the ores to determine how much of the manganese could be recovered in concentrates assaying a minimum of 40 percent manganese (Mn) and containing a maximum of 16 percent iron (Fe), 15 percent silica (Si02) plus alumina (AI203), 0.3 percent phosphorus (P), and I percent copper (Cu) plus lead (Pb) plus zinc (Zn). All chemical analyses of the ores and test products were done at Salt Lake City. In all, 567 ore lots submitted to the Deming depot were tested by flotation to determine their amenability to concentration into specification-grade material; 421 lots were amenable, and 146 were unamenable, primarily because of high copper content or excessive silica or iron in the flotation concentrate. Chemical analyses totaling 42,700 were made on the ores submitted to the Deming depot and on the products of the amenability-test program.

Jan 1, 1959

By L. A. Haas

S02 reduction with CO was studied in an integral flow reactor at a nominal flow of 0.5 liter per minute. Reactant gas contained 3 percent SO2, 6 percent CO, and the balance He. SO2 conversion was determined for three different types of catalysts. The first consisted of 16 commercial catalysts used for various chemical syntheses. Only the commercial catalysts which contained transition metals in alumina removed more than 30 percent 80a at temperatures below 510° C. Two other types of catalysts were prepared in the laboratory either by pelletizing equal amounts of powdered alumina and transition metal oxides or by impregnating commercial alumina tablets with transition metal ions. Regardless of preparation techniques, Cr and Fe in alumina were the two best catalysts. The observed results suggest that an intermediate (SCO) is formed by the interaction of surface metal sulfides and carbonyls. Alumina then catalyzes the interaction of SCO with S02 to form the end products (sulfur and carbon dioxide). Over 80 percent S02 was removed at 460° C with 2 grams alumina impregnated with 2.5 percent iron.

Jan 1, 1972

By F. J. Perzak

The Bureau of Mines conducted a study to develop a standard fire test for 5-gal containers used for storing combustible fluids in underground coal mines. A standard test method was developed which evaluates the performance of the container in a 4-min tray fire. Bureau investigators used the standard test method to evaluate several types of closed 5-gal plastic and metal cans in outdoor tests. Each can tested contained 1 gal of nonfire-resistant (NFR) hydraulic oil. A container failed the test if it lost its contents in any of seven trials. Contents spilled either as a result of thermal rupture or melting. Fewer than 10 pct of the metal containers failed this criterion, but all the plastic containers failed. The metal container failures were usual-ly due to tipping over during pressure relief, which spilled the NFR oil. Replacing the NFR oil in the container with kerosene resulted in failure of more than 30 pct of the metal containers. The standard tests and preliminary tests showed that plastic containers are not equivalent to metal containers in their ability to contain combustibles such as lubricants and greases in a fire. For solvents and lubricants more volatile than NFR hydraulic oil, approved metal safety containers are recommended.

Jan 1, 1985

By R. V. Ramani, J. M. Mutmansky, J. Qin, J. Organiscak, R. Bhaskar

"The results of a two—year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the ¬analysis results and conclusions of the study are discussed.The results of the study indicate that the quartz contents of the airborne dusts are generally higher than those in the host material and bulk samples; and the quartz content increases with decreasing size of the airborne dust. The source for quartz appears to be the roof and the floor materials rather than the coal seam itself. It also appears that the material containing quartz may be breaking into a different size distribution than coal.INTRODUCTION Without doubt, the potential for permanent and severe health damage exists due to respirable dust in the work environment. The attention directed at the reduction of respirable airborne dust to levels below those specified in the law and the achievements to date in meeting these standards are but a reflection of the recognition by many parties government, industry, and labor - of this potential and the need to reduce it.The ambient dust standard in underground U.S. coal mines (2 mg/s3) has a qualifier (Code of Federal Regulations, Title 30, Part 71.101) to determine an applicable dust standard when a respirable dust sample contains more than 5% quartz. This standard is frequently referred to as the ""reduced standard."" The reasoning behind the reduced standard is the relative toxicity of the quartz dust compared to that of pure coal dust. As the quartz levels in samples increase, the applicable standards become more stringent and maintaining the workings in compliance becomes increasingly difficult.The number of underground work locations operating under the reduced standards has shown a dramatic increase since 1980 (Figure 1). For comparison purposes, there were no mining entities operating on reduced standards prior to 1977. The emergence of this problem, which affects the health and safety standards on one hand and creates severe compliance problems on the other, has been rapid."

Jan 1, 1990

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants.

Jan 1, 1924

By M. Kanda

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in and above an operating coal mine, McElroy Mine, located near Moundsville, West Virginia. The electromagnetic environment created by 300 volt dc and 480 volt ac machinery was measured. In one technique noise was measured over the entire electromagnetic spectrum of interest for brief time periods. The noise was recorded using broadband analog magnetic tape. The noise data was later transformed to give spectral plots. In the other technique, noise amplitudes were recorded at several discrete frequencies for a sufficient length of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By Dennis McLaughin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine?s Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested 2nd demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

Jan 1, 1981