Search Documents

By A. G. Loomis

METHODS for measuring relative permeability as a valid function of saturation were compared by the. Bureau of Mines, using core samples from representative oil-productive California formations, from the Bartlesville sand in Oklahoma, and from synthetic samples. Measurements for gas-oil systems were made by steady-state dynamic, unsteady-state displacement and two stationary-phase methods. Measurements for water-oil systems were made by the unsteady-state displacement method. As the ratio rather than individual relative permeabilities is measured by the last method, three methods for calculating individual relative permeabilites from their measured ratio were compared for gas-oil systems and two methods for water-oil systems. Errors arising from capillary discontinuities, such as the end effect and stabilized-zone flow, are discussed and evaluated; possible errors rocs arising from turbulant flow are also examined. The inapplicability of non-steady-state methods for water-oil systems that are not definitely oil-wet is discussed in detail. Measurements of relative permeability to both gas and oil can be made quickly and accurately by the steady-state dynamic method when rates of flow of the two phases are sufficient to minimize the capillary discontinuity at the outflow end of the sample. At such rates relative permeability-saturation measurements are essentially independent of the rate of flow. The steady-state method wits modified by a dispersion section at the inflow end of the sample acid designated tie dispersed-feed method.

Jan 1, 1962

By C. R. McCann

The Bureau of Mines conducted an experimental study of conditions needed to produce flames of pulverized coal when the heat needed for ignition is sup-plied only from the flame and hot furnace refractory. An electrically heated furnace which burned about 1 pound of coal per hour was designed and fabricated. A sheath of air, surrounding the primary coal and air stream, was used to prevent entry of hot gases from recirculating combustion products. Furnace temperatures needed for ignition ranged from about 1,8300 F for an Illinois coal to 2,250° F for a Beckley seam coal. Apparent flame velocities were about 2 to 5 feet per second, increasing with volatile content of the coal and with distance from the burner mouth to the flame. The time required for ignition, approximately 0.02 to 0.07 sec, was a better measure of flame behavior than was velocity.

Jan 1, 1969

By R. A. Friedel, J. L. Shultz, A. G. Sharkey

The purpose of this investigation was to study the primary materials associated with the coal structure . Mass spectrometric techniques can be useful in studying the chemical structure of coal and various high- molecularweight materials derived from coal . Investigations of pyrolysis products and extracts of coal , and also whole coal , showed : 1. Aromatic hydrocarbons obtained by the vacuum pyrolysis of coal below 300 ° C possibly were sorbed material rather than decomposition products . 2 . 2 . Thirteen structural types having molecular weights from 78 to 400 were identified in pyridine extracts constituting one - quarter or more of the coal by weight . 3. Material extracted at room temperature with a methanol - benzene solvent and a vacuum pyrolysis condensate obtained at 450 ° C contain similar components . The extract and the condensate have approximately the same average molecular weights ( 200-300 ) . 4. Material extracted from coal at room temperature is altered even by mild thermal treatment . 5. Changes in various alkyl series occurring in thermally treated coal extracts can be followed quantitatively . 6. Similarities in the spectra of coal and graphite were indicated in an investigation using a mass spectrometer equipped with a spark source . Determinations on a coal - ash sample by this technique showed good agreement with data obtained by emission spectroscopy .

Jan 1, 1963

By Roy L. Wilfong

The thermal decomposition of the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of praseodymium, neodymium, and samarium was investigated thermogravimetrically in the temperature range 25° to 1,500° C. Each salt was decomposed at a heating rate of 2.5° C, per minute. The pyrolytic sequences have been identified and the temperatures of formation of inter-mediates, the minimum oxide formation temperatures, and values for loss on ignition have been determined. The nonstoichiometric ranges between Pr6011 and Pr203 and the extent of these ranges have been determined for oxides derived from the carbonate, nitrate, and oxalate salts of praseodymium. The alum and sulfate salts of praseodymium produced the sesquioxide without forming the intermediate non-stoichiometric oxides. The temperature limits of formation and regions of stability for the alums and sulfates were better defined than were those for the carbonates, nitrates, and oxalates. The minimum oxide formation temperature increased in the order of samarium, neodymium, and praseodymium irrespective of the anion.

Jan 1, 1962

By W. J. Wuest

This U.S. Bureau of Mines report presents an overview of ground control considerations associated with cutter roof failure. Many of the relevant U.S. and international research studies since the late 1940's are reviewed, and summaries of recent design guides are included. Factors affecting cutter roof, such as underground stress field and rock structure around the entry, are described. Strata control techniques are also outlined. These techniques are divided into three sections: artificial support, mine structure design, and multiple-seam extraction. Other subjects covered in the report include monitoring and prediction, effect of geologic features, and mapping of adverse mining conditions. The emphasis of this report is on practical considerations; theoretical discussions are minimal.

Jan 1, 1994

By J. M. Singer

In this Bureau of Mines study coal and rock dust beds were entrained by airblasts generated by gas explosions at the closed end of a 0.61-m-diameter explosion tunnel, 49.7 m long. The system was designed to simulate entrainment of mine dust deposits by accidental gas explosion at the coal face of nonintersecting mine passageways. Full-scale mine explosion trials confirmed many of the results of the explosion tunnel experiments and indicated several new features of dust entrainment. Dispersal of 20.3-cm-long stepped dust beds located 35 m from the closed end always began during the early portion of the ascending gradient of the first transient airflow (and pressure) wave, and was usually completed before the end of the first quarter-wave period. Bulk quantities of dust were entrained simultaneously by longitudinal regression from the leading edge of the dust bed and by surface lifting of the top layer. Instantaneous threshold air velocities for bulk quantities of coal and rock dust beds in separate, mixed, and layered configurations were in the same range (5 to 30 m/sec) as previously found under steady-state velocity conditions. Selective lifting of coal dust layers from rock dust occurred when the threshold dispersal velocity of coal dust but not of the underlying rock dust was exceeded.

Jan 1, 1976

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at B vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

By Irvin Pritts

This report describes the design, fabrication, and testing of a prototype instrument which demonstrates the feasibility of determining respirable coal dust concentrations by light reflectance photometry. Coal dust is collected on a filter and the quantity collected is continuously monitored by reflectance-photometry. Light emission and detection is accomplished by reflective object sensors, which have both light source and detector in one chip. The use of a pulsed light source insures low drift characteristics of the measuring circuitry. The collection of the respirable coal dust on filters facilitates accurate calibration and also allows measurement verification, if desired, by well-accepted, gravimetric methods.

Jan 1, 1981

By The Staff, Explosives Research Center

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1962, to June 30, 1963, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1963; in general, the research reported in these publications antedates the report period.

Jun 24, 1964

By Wm. O. Vanderburg

This report on the mining and milling of tungsten ores is the second part of a general study of the domestic tungsten industry. The first part, comprising general information on tungsten, has been printed as Bureau of Mines Information Circular 6821. The purpose of these papers is to increase efficiency in the mining, preparation, and utilization of the tungsten resources of the United States. The tungsten industry forms so small a part of the vast mining and metallurgical operations of the illation that private metallurgists have not had enough inducement to give special attention to the recovery of tungsten minerals from the ores, and many of the small companies are financially unable to undertake research work. A study of the milling of tungsten ores reveals that further improvement is possible, especially in the treatment of slimes. Recent experimental work by the Bureau shows that the flotation process is applicable to certain tungsten ores. The future of the tungsten industry it the United States depends to a great extent on utilization of the low-grade deposits of the contact-metamorphic type.

Jan 1, 1935

By F. M. Jenkins

Longwall mining systems are used to mine approximately 50 pet of the world's total underground coal production. Single entries are the predominant method of longwall development in Europe and Asia, where mining conditions are more severe than those encountered in the United States. During the 1970's and early 1980's, the U.S. Bureau of Mines and the U.S. mining industry invested nearly $20 million in single-entry and related research. This report reviews the accomplishments of single-entry research in the United States and describes two U.S. single-entry field projects: the Sunnyside single-entry project in central Utah and the tunnel-boring project in northern West Virginia. Also discussed are a single-entry study conducted by North American Mining Consultants (NAMCO) and a single-entry design study conducted by Ketron, Inc. This Bureau report compares the resulting technology with European counterparts to further assess the utility and efficiency of U.S. systems.

Jan 1, 1990

By Thomas A. Morgan

The distribution of stress adjacent to each of 25 mine openings was determined by the borehole stress-relief method in the FMC Corp. Westvaco trona mine at Westvaco, Wyo. The purpose of the stress determinations was twofold: First, to study the effect on these distributions of various factors such as opening shape, stress level, and loading history; and second, to estimate the distribution of stresses adjacent to extensive high-extraction (85 to 100 percent) areas. Stress distributions in areas of low average stress correspond closely to the theoretical distributions based on elastic theory. However, in areas of high average stress, the stress distributions are of a type associated with plastic failure. The stresses adjacent to a mined-out area supported by remnant pillars were significantly higher than the stresses adjacent to another area in which the remnant pillars were removed.

Jan 1, 1965

By A. L. Service

In 1965 the Western phosphate industry ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock and phosphate rock products. It has become an important regional industry and, since the close of World War II, it has become important in the national phosphate economy. This report includes an evaluation of the trends and outlook for the Western phosphate industry through 1975 as part of the Bureau's program to determine the rate at which the Nation's mineral resources are being utilized. The first part of this report is concerned with the relationship between the Western phosphate industry and that of the United States and the world. It describes the principal phosphate deposits and discusses production, export, and import of phosphate rock and marketable products. The second part of the report is concerned with the Western phosphate industry and discusses trends and outlook through 1975. Projections for the utilization of phosphate rock, phosphate fertilizers, and elemental phosphorus have been developed and extended through 1975 in an effort to provide data and information pertaining to the rate of depletion of the Nation's phosphate resources.

Jan 1, 1967

By P. H. Floyd

This report presents the results of laboratory and continuous mill-beneficiation tests conducted at the Bureau of Mines Northwest Electra Development laboratory, Albany, Oreg., on nonsulfide lead ore from the Sherman mine, Leland district, near Burke, Idaho. The predominant lead-bearing mineral in the ore sample treated was pyromorphite, a minor ore mineral of lead. Known reserves of pyromorphite lead ore in the United States are limited, although an appreciable tonnage of this type of ore is found in the Sherman mine. Very little pyromorphite is being mined in this mine or in the United States. This beneficiation problem presented a unique opportunity to study the mineral-dressing properties of a less widely known lead mineral, and consequently adds valuable knowledge to the ways of beneficiating ores containing nonsulfide lead values. This mineral-dressing problem was successful with conventional concentration methods of flotation and Gravity separation.

Jan 1, 1952

By Larry A. Haas

The chemistry of current or potential SO2 removal processes can be placed into four categories: (1) reduction, (2) Liquefaction, (3) direct dissolution, and (4) oxidation. Methods that involve reducing SO2 to elemental sulfur appear promising since this product can be easily handled, shipped, and stock- piled. Unfortunately, SO2 cannot always be reduced directly when other oxidizing agents are present. Thermodynamic data indicate that some oxidizing reagents will also consume reductant at the reduction temperature. A two- stage process can be applied to waste gases that contain excessive quantities of oxygen, nitrogen oxides, and water vapor. The best sorbent for the first stage appears to be a nonalkali or nonalkaline earth medium since this medium more readily releases the SO2 for reduction in the second stage.

Jan 1, 1973

By James Westfield

A brief résumé follows of recent activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority (under Executive Order 9728) was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1958

By T. E. Swigart, C. E. Beecher

The Federal Government, as the largest lessor of oil and gas lands in the United States, is vitally interested in the conservation of those resources. This manual has been prepared at the direction of the Secretary of the Interior to call the attention of lessees of public oil and gas lands to the most common oil and gas field wastes and the best methods of preventing them; to outline the policies of the Interior Department on field operations; and to give information as to how the "Operating Regulations" of the department will be interpreted by the Bureau of Mines. The oil industry has progressed steadily. Present operating methods are much more efficient-and less wasteful-than those of a few years ago; moreover, the art of producing oil and gas is continually advancing. Public interest requires that improved methods, which will result in obtaining the greatest possible amounts of oil and gas from the natural deposits, shall be developed and used. Part I of this manual points out types of oil and gas wastes and suggests, in detail or by reference, the most practical and effective methods in current practice for stopping these wastes. Throughout Part I the department's operating policy is given, with interpretations of the "Operating Regulations" for enforcing every practical measure of conservation. Part II comprises the revised "Operating Regula-tions" which supersede all previous regulations and will govern future operations on public lands; it will be found in the pocket in the back cover of this bulletin.

Jan 1, 1923

By Thomas M. Barczak

Wood cribs are used extensively by the mining industry to stabilize mine openings. While the cost per crib is relatively low, their extensive use can result in annual mine costs of over $1 million. In an effort to improve the utilization of these supports and to reduce ground control hazards, the U.S. Bureau of Mines has developed engineering methods to assist mine operators in wood-crib design and employment. Design and employment criteria are established based on the strength, stiffness, and stability of the crib structure in relation to the load conditions imposed by the mine environment. Models have been developed based on full-scale tests in the USBM's Mine Roof Simulator that compute the capacity of wood cribs of various configurations and material constructions as a function of displacement of the crib structure due to roof-and-floor convergence. These models permit the comparison of the loading characteristics and costs of employment of different crib designs, and in conjunction with roof behavior models, provide a means to determine the optimum design and employment strategy.

Jan 1, 1993

By M. H. Kline

The Great Gossan Lead in Carroll County, Va., is one of the largest undeveloped sulfide ore bodies known in the eastern United States. It extends for 16.7 miles along the western slope of the Blue Ridge Mountains (fig. 1). The various known segments of the deposit, extending from the southwest end to the northeast, are: The Great Outburst or Iron Ridge segment, Chestnut Creek, Copperas Hill, Sarah Ellen, Wild Cat, Cranberry, Dalton Hill and offset segment to the south of the Cranberry, Little Reed Island, Little Vine, and the Betty Baker at the northeast end. All of these segments have been explored or mined to various extents in the past for the iron gossan and secondary copper ore. The Great Outburst or Iron Ridge segment is now being mined by the General Chemical Division of the Allied Chemical & Dye Corp. for the sulfur and iron content of the primary ore. These deposits are becoming increasingly of Interest as a. large potential source of iron and sulfur owing to their proximity to Birmingham, where the burned cinder sells at a premium, and to the acid markets of the region.

Jan 1, 1949

By Gregory Molinda

Historically, coal miners have known that roof shales can deteriorate in contact with humid mine air, causing massive roof falls and injuries from falling rock. It is critical to recognize rocks prone to weathering and to adequately support these rocks in order to ensure the long-term stability of the openings. In a recent study, NIOSH has used a wet/dry cycling test to determine the moisture sensitivity of over 800 specimens of roof rock from 25 U.S. coal mines. Fireclays and some gray shales are the most moisture-sensitive. Rocks with disturbed bedding, in contrast to flat-bedded rocks, are also more sensitive to water. Black shales are relatively un-reactive to moisture and serve to protect more reactive gray shales above. Mines that have roof rocks with moisture-sensitivity indexes above 40% can experience slaking roof conditions, and many require high coverage surface controls. Three case studies are presented in which the moisture-sensitivity index is correlated to roof conditions underground, and can be used to indicate long term deterioration. Engineering measures are described to control moisture-sensitive roof. In one case, roof screen not only reduces injuries from rock fall but also is shown to reduce roof falls. Keywords: coal mining, roof control, slaking, roof support, rock falls

Jan 1, 2008