Search Documents

By Roger A. Dworak

This report describes in detail the work done on the development of the Time Domain Reflectometry Microcomputer (TDRM). Modifications to the FMC-Model 302A Cable Fault Locator is described in Appendix D. The TDRM unit uses an 8080 microcomputer to accurately locate major faults in low capacitance cables to within ± 1 foot when properly calibrated. Major faults in high capacitance cables are usually located within ± 5 feet. The upper limits of fault detection are <1 kilohm shunt fault and >7 ohm series fault. In practice fault detection limits are reduced to <300 ohms shunt fault and >30 ohms series fault because of discontinuities caused by cable repair.

Jan 1, 1977

By Lester J. Crow

This study advances the use of elemental sulfur in structural materials by demonstrating its value in bonding high-strength, well-graded basalt aggregates to form sulfur-basalt concretes. Sulfur is an excellent bonding agent, and the strength of a thermoplastic sulfur-aggregate mixture depends, to a large degree, on the strength and grain-size distribution of the aggregate used. A 3-cubic-foot, electrically powered mixer with heat applied to the barrel was used to mix the sulfur and aggregate. Sulfur content of several mixtures was varied to obtain the best workability with a minimum of sulfur in excess of that necessary to fill the voids. The average grain sizes and grain-size distributions were also varied to determine their effects on strength. Unconfined compression tests of forty-five 6-by l2-inch cylinders yielded average strendths of 3,348 psi to 10,398 psi. The highest strength single cylinder was 10,717 psi. The cylinders were tested from 24 hours to 6 days after pouring; after 24 hours the rise in strength was very slight. From the results obtained it appears that sulfur can be a useful construction material. An evaluation was made of a high-vacuum application for sulfur concrete. Sulfur has a high vapor pressure at elevated temperatures, 50° to 100° C; consequently, significant losses by sublimation can be expected. At lower temperatures the losses are not significant; however, this factor will limit its use at a higher temperature.

Jan 1, 1970

By S. S. Cole, C. E. Wood, T. L. Joseph

"INTRODUCTION Iron ore containing titanium was first used in blast furnaces over a century ago. It is well known that TiO2 is a slag-forming material that will increase the amount of slag produced by the usual gangue materials, silica and alumina. Increase in the volume of slag due to the presence of TiO2 and a lack of information concerning its effect on the properties of the slag have prevented the general use of titaniferous ore. Also rather com¬mon belief among furnace operators that the bottom of the furnace builds up when ores containing TiO2 are smelted has militated against the use of titaniferous ore. This building up of the hearth has been attributed to the formation of copper-colored crystals of titanium cyanonitride, which have been observed in the salamanders of blast furnaces. Until recently the availability of nontitaniferous iron ore has left little incentive to use ore containing titanium.The presence of vanadium in certain deposits of titaniferous magnetite in New York State has created new interest in problems connected with the use of titanium-bearing ore. It appears that most of the vanadium in this ore can be recovered in pig iron, which can be blown in a converter to produce a slag containing vanadium in amounts suitable for the production of ferrovanadium.The Titanium Division of the National Lead Co. recently erected a largo mill to treat ore from Sanford Hill, in Essex County, New York, about 50 miles west of Port Henry. The ore deposit was acquired from the MacIntyre Iron Co. and is often referred to as Sanford ore. It is one of the largest deposits of Iron-bearing material to be found east of the Lake Superior region and is being mined by open-pit methods."

Jan 1, 1943

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine ventilation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which accounts for a major portion of the market for coal, received further study. Unique power generation systems, including coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jan 1, 1965

By Galen G. Waddell

The Deep Creek zinc and lead mine afforded an excellent example of a relatively small underground mine operation that approached the low mining costs of large, highly mechanized mines, An open stope mining method incorporating sublevel benches and vertical long holes was used (fig. 1). Detailed descriptions are given on the exploration program, stope development, stoping procedures, and pillar removal. Pressure grouting was used to check the inflow of water and thus prolong the life of the mine. Statistics on mining costs and on electric power consumption, haulage from mine to mill, and milling costs are included.

Jan 1, 1963

By Kevin Malone

Mercury, or quicksilver as it is often called, has many applications in modern technology. Used principally in electrical apparatus, industrial contol instruments, insecticides and fungicides, electrolytic preparation of chlorine and caustic soda, chemical processes, pharmaceuticals, and dental preparations, the liquid metal has unusual properties that make it a preferred material for many industrial uses. United States consumption of mercury during the past 40 years shows a rising trend. In all except 4 years, U.S. production has been less than the domestic requirement, and imports, principally from Spain, Italy, and Mexico, have supplied most of the deficit. After World War II, domestic output decreased rapidly until 1950, when it was the lowest in the 100 years covered by production records. Higher mercury prices since 1950 have reversed the decline in domestic output and reduced the gap between U.S. production and consumption. Domestic output in 1958 was the highest in peacetime since 1883; however, the nation still imported 28 percent of its mercury requirements from 1950 to 1960 the price of mercury was high as a result of industrial applications of the mercury cell, the impact of the cold war and the Korean war, and the Government stockpiling program. The stockpiling program, in effect, put a floor under mercury prices even though only 9,428 flasks of domestic mercury went into the stockpile under the original program which ran from July 1954 to December 31, 1957. Under an extension of the program, an additional 17,463 flasks was purchased.

Jan 1, 1962

By Peter J. Clarke

The petroleum industry continued to be the most important mineral activity in Bahrain during 1978-79. Revenues generated by the petroleum sector increased from $378 million&apos; in 1977 to an estimated $419 million in 1978 and approximately $522.5 million in 1979, despite decreasing production over the 2 year period. There were two oilfields that produced revenues for Bahrain, the Awali oilfield, the nation&apos;s only onshore producer, and the Abu Sa&apos;fah oilfield, located in the Persian Gulf, north of Bahrain, The Await oilfield has been decreasing output from a high of 27,973,000 barrels in 1970 to 19,000,000 barrels in 1979. Bahrain shared the revenues from the Abu Sa&apos;fah oilfield with Saudi Arabia, as settlement of an ownership dispute. For the first time, in 1978, revenues from the Abu Sa&apos;fah oilfield represented over 50% of the total receipts from the petroleum sector. The years 1978-79 saw the gradual takeover of the Bahrain Petroleum Co. (Bapco), formerly a subsidiary of the California Texas Petroleum Co. (Caltex), by the Government-owned Bahrain National Oil Co. (Banoco). By yearend 1978, Banoco owned 60% of Bapco, and Caltex the remaining 40%. The Government-owned company controlled exploration concessions, managed domestic marketing of petroleum products, and controlled natural gas production and marketing. On December 15, 1979, the Bahrain Government completed full takeover of the Bapco operations. Bapco will continue to own and operate the 250,000-barrel-per-day oil refinery located near Sitrah, as well as handle foreign marketing of petroleum products.

Jan 1, 1981

By Frank E. Cash

Although during the past 10 years Alabama has attained an enviable position by its coal-mine accident experience and, like most of the other coal-mining States, has made progress in the safer operation of coal mines, there is still room for improvement, which can be realized only by still greater efforts on the part of employees and employers. From 1993, when accidents were first recorded by the Alabama State Mine Inspection Department, to 1934, inclusive, 3,451 men lost their lives in the production of 569,722,676 tons of coal. The primary purpose of this report is to bring to the attention of the mining industry in Alabama end elsewhere statistics of fatal accidents for 1931-34, with the hope that a study of the causes may lead to reduction of similar accidents in the future.

Jan 1, 1936

The revised inspection standards or recommendations herein have been prepared for use in Federal inspection of bituminous-coal and lignite mines. They succeed a compilation of similar standards published as Bureau of Mines Information Circular 7268 in December 1943 and employed as a guide in Federal inspections since that time. Important alterations and additions have been made because of changes in mining, practice and temporary shortages of some safety equipment; moreover, several previous standards have been found not generally applicable and have accordingly been deleted. Mining methods and equipment continue to change, and new hazards and new safeguards are introduced. Consequently, these standards are subject to revision from time to time. Questions from the coal-mining industry regarding these standards and suggestions as to changes and additions thereto will be welcomed and considered carefully when the next revision is made. Many constructive criticisms from the mining industry have been considered in preparing this edition.

Jan 1, 1945

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to review the air and water monitoring requirements of five Federal environmental acts (the Federal Water Pollution Control Act, the Safe Drinking Water Act, the Clean Air Act, the Surface Mining Control and Reclamation Act, and the Resource Conservation and Recovery Act) and to compile information on the currently available monitoring instruments. A literature review of the acts and their associated regulations was conducted to determine applicability to the mining industry as well as any air and water monitoring requirements. In addition, an industry search and literature review was performed to assess the instrumentation available to comply with the monitoring regulations. Based on this research, the instruments are classified by general applicability to air, surface water, or ground water monitoring, then catalogued by monitoring parameters. A discussion is provided on recommended and innovative monitoring techniques.

Jan 1, 1981

By C. M. Harrer

The location, features, qualities, and extent of iron occurrences and the associated resources--limestone and dolomite, bentonite, coal-lignite, petroleum and natural gas, power, and water--are evaluated. The results of pioneer beneficiation tests on South Dakota taconite are discussed. In addition, pertinent features of taconite development, cost factors, the Western and Central United States trade area and markets are reported. The State&apos;s production of iron ores until 1963 has been small and for purposes other than the manufacture of iron. This investigation disclosed the probability of large resources of taconite in Pennington and Lawrence Counties. The average iron content is 29 percent, and a 65-percent or better iron concentrate might be produced. Ample resources are available for mining and processing taconite. An investment of at least $26 million would be required for a plant capable of turning out 1 million tons of agglomerated iron concentrate per year. The feasibility of such an enterprise is indicated, but intensive investigation and research must be completed to justify such an investment,

Jan 1, 1966

By G. F. Livingston, F. K. Shelton, J. C. Stahl, R. E. Churchward

"INTRODUCTION An investigation of the metallurgy of cobalt from domestic ores has been in progress since February 1940 and has resulted in the formation of a hydrometallurgleal process for the production of electrolytic cobalt metal. Previous reports of these investigations have been given by F. K. Shelton; 7/ and Ruth E. Churchwrd, F. K. Shelton, and G. Knickerbocker. 8/ Briefly, the process, as applied to ores containing cobalt oxide, consists of leaching with H2SO3 or, preferably, with H2SO3 and H2SO4, to dissolve the cobalt. The cobalt solution passes through one or more purification stages to remove iron and elements of the copper group, and cobalt carbonate is precipitated under carefully controlled pH conditions. The cobalt carbonate is dissolved in on acid electrolyte containing sulfuric acid, boric acid, and sodium fluoride. The electrolyte then proceeds to electrolytic cells where cobalt is plated as a metal and sulfuric acid is regenerated.The present paper contains the results of several investigations signed to give a more complete chemical and engineering understanding of different unit processes involved in the electrowinning of colbat. Some work has been done to broaden the process to include arseniferrous cobalt ores as well as the oxide ores upon which the investigation was initiated. Most of the data presented herein have been obtained since the release of the previous reports; any changes suggested heroin that conflict with recommendations in earlier reports are based on more complete data and usually are preferable."

Nov 1, 1945

By Jack Touseull

On November 15, 1972, the Bautsch mine, a lead-zinc mine in Paleozoic dolomites, experienced a massive rock failure involving 3 to 5 million tons. Because this failure was large and extended to the surface, it was included in the Federal Bureau of Mines investigations on "Massive Rock Failures." Analysis of the rock mechanics and mode of failure revealed that failure at the Bautsch mine was the result of the interrelationship of many factors. Factors related to the failure were found to be external and internal to the mining environment. Unlike internal factors, external factors were not apparent and, therefore, many external factors were investigated; some of which are not normally considered in rock mechanics analyses. External and internal factors determined to be of significant importance were: (1) precipitation, (2) fractures, (3) plastic clay layer, (4) topography, (5) rock alteration, (6) bedding, and (7) mining zone dimensions. Because of the conditions at the mine, failure could have been predicted without extensive instrumentation. Application of basic geologic and engineering principles to the internal and external factors could have predicted failure. Alternately, failure would, in all probability, have been delayed by years if, after 1962, mining had been curtailed in the area of failure.

Jan 1, 1980

By E. J. Gleim

An important phase in the Bureau of Mines investigation of electrical machines designed for operation in gassy coal mines is testing enclosures of electrical components for explosion-proof qualities. In brief, this testing consists of filling and surrounding the enclosure with an explosive atmosphere of methane and air and then igniting the atmosphere within the enclosure to determine (1) Whether the resulting explosion is confined without discharge of flame; (2) whether the enclosure walls are permanently distorted; and (3) whether excessive pressures are developed within the enclosure. Ordinarily, the pressures encountered in routine testing do not exceed 100 pounds per square inch gage. Hence, the designer of the machine does not have too much difficulty in taking corrective measures to prevent flame discharge and distortion of the enclosure. Occasionally, however, the explosion pressures greatly exceed 100 pounds. Then the goblet of the designer may not be solved so readily, From experience over the year 0, the testing personnel often can predict that certain construction will result in high. Pressures, but, only in a very general way, has it been possible to advise designers what modifications might be made to reduce the explosion pressures to normal values. For example, if high pressures were developed in a motor starter having a partition with an opening through it, some enlargement of the opening may appear to be the logical procedure, but it has not been- possible to give information concerning the exact amount the opening should be enlarged to prevent development of high pressures .

Jan 1, 1952

By W. S. Landers

Nine high-volatile bituminous Utah coals were carbonized singly and in blends with low-and medium-volatile bituminous coals. Of the 9 coals, 2 are in commercial use as the base coals in blends that produce industrially accept-able metallurgical coke, while 7 are regarded as weakly coking and are not used commercially in coking blends. The carbonization tests were made in a la-inch diameter, cylindrical retort, using 50-pound charges. Sunnyside coal blended with autogenous char generally produced larger and stronger coke than was yielded by straight Sunnyside coal. The volatile matter of the char and the concentration of the char in the blend appear to be important parameters influencing coke size and strength. A blend of 10 per-cent autogenous char of 7.2-percent volatile matter with Sunnyside coal yielded coke that was larger, stronger, and of higher apparent specific gravity than coke produced from an industrial coke oven blend consisting of 15 percent medium-volatile coal and 85 percent Sunnyside coal.

Jan 1, 1967

By Robert C. Merritt

This report describes laboratory as well as pilot heap leaching investigations of low-grade sandstone ores from Wyoming, New Mexico, and Colorado. Sodium carbonate-bicarbonate solutions containing sodium hypochlorite extracted up to 86, 54, and 16 percent U308 from Wyoming, New Mexico, and Colorado ores, respectively. Ammonium carbonate-bicarbonate solutions containing sodium hypochlorite were less effective at leaching these ores. Acid leach in replicate pilot plant testing resulted in U308 extractions of 96, 88, and 81 percent from the Wyoming, New Mexico, and Colorado ores. The development of cost-effective processes for extracting uranium from low-grade ore is essential to the assurance of a continuing domestic supply of uranium.

Jan 1, 1977

By W. W. Adams

"The results of the fourth annual safety contest, 'mown as the National Safety Competition, contacted by the United States Bureau of Mines are herein announced. A bronze trophy, ‘Sentinels of Safety’, the gift of the Explosives Engineer magazine, has been awarded to the leading mine in each of the five groups into which the mines and quarries that participated in the contest were arranged. These five groups were: anthracite mines, bituminous coal mines, metal mines, nonmetallic-mineral mines, and carries and open-pit mines. The leading plant in each group was the mine whose employee lost the smallest number of days from accidents in proportion to the total number of man hours worked. Where two or more mines operated without a lost-time accident, the winner was adjudged to be the plant which operated the largest number of man hours during the year.The contest was based upon reports of accidents and exposure sent by the competing companies to the Bureau of Mines. Records of the five leading companies in each group were made known to a Committee of Award, consisting of the following seven members: H. Poster Bain, Secretary of the American Institute of Mining and Metallurgical Engineers; James F. Callbreath, Secretary of the American Mining Congress; W. H. Cameron, Managing Director of the National Safety Council; H. L. Gandy, Secretary of the National Coal Association; A. T. Goldbeck, Director of the Engineering Bureau of the National Crushed Stone Association; William Green, President of the American Federation of Labor; and A. J. R. Curtis, Assistant to the General Manager of the Portland Cement Association. Members of the committee voted for the winning company in each group in accordance with the rules governing the contest.. A majority vote prevailed."

May 1, 1929

By John A. Johnson

"INTRODUCTION The use of wet drilling with adequate ventilation has largely controlled production of dust in drilling rock; however, in some operations, such as shaft sinking and modern tunnel driving, when each of a number of drills is operating in a small cross-sectional area, it is at times difficult to ventilate well enough to keep the dust concentration within desired limits.Some chemical compounds, known as wetting agents, when added to water in small quantities reduce the interfacial tension and make it possible for the solution to wet dust particles more effectively than water alone.This report presents results of tests on the effectiveness of two wetting solutions in reducing the amount of dust produced by wet drilling in basalt.ACKNOWLEDGMENTSThe tests were conducted the Bureau's Mount 'Weather Testing Adit,Mount Weather, The author acknowledges the assistance and cooperation of Wing G. Agnew, superintendent; Marvin M. Revelle, mining-engineering aide; and the rest of the crew at Mount Weather in conducting the tests. C. W. Owings, mining engineer, Safety Division, assisted in conducting some of the first tests and gavel valuable advice and guidance throughout the work and in preparing this report."

Jan 1, 1943

By R. L. Marek

The number of Persons fatally injured in the petroleum industry in California in 1930 was 50, a decrease of 20.6 per cent from 1929, when 63 men accidentally lost their lives. The decrease in the number of fatalities for 1930 has caused the first downward trend in the fatality curve of the California petroleum industry since 1927 and is coincident with a period of little active development in new fields, the shutting in of many wells, and reduced activity in the older fields of the State. That a direct relationship exists between the number of accidental deaths and the rapidity of new field development is particularly emphasized by the fact that in 1929, a year of intensive field development in California, 48 men were killed in the drilling and producing division, whereas in 1930, a year of less development work, only 25 men were killed in this division. The figures for the average number of drilling and producing wells in 1930 decreased appreciably from comparable figures for 1929 and a greater percentage of producing wells were shut-in in 1930 than in 1929.

Jan 1, 1931

By R. L. Marek

The number of persons fatally injured in the petroleum industry in California in 1930 was 50, a decrease of 20.6 per cent from 1929, when 63 men accidentally lost their lives. The decrease in the number of fatalities for 1930 has caused the first downward trend in the fatality curve of the California petroleum industry since 1927 and is coincident with a period of little active development in new fields, the shutting in of many wells, and reduced activity in the older fields of the State. That a direct relationship exists between the number of accidental deaths and the rapidity of new field development is particularly emphasized by the fact that in 1929, a year of intensive field development in California, 48 men were killed in the drilling and producing division, whereas in 1930, a year of less development work, only 25 men were killed in this division. The figures for the average number of drilling and producing wells in 1930 decreased appreciably from, comparable figures for 1929 and a greater percentage of producing wells were shut-in in 1930 than in 1929.

Jan 1, 1931