Search Documents

By Forrest T. Moyer

Injury experience at coal mines and mechanical-cleaning plants (excluding officeworkers ) in 1967 was 222 fatal and 10,115 nonfatal disabling work injuries during an exposure time of 241.8 million man-hours. These injuries occurred at a frequency rate of 42-75 per million man-hours worked; the severity rate was 7,699 days lost or charged per million man-hours. Each of these general measures of injury experience was lower than similar data recorded for 1966. Employment at 6,885 coal mines and 569 mechanical-cleaning plants, excluding officeworkers, averaged 139,312 men in 1967. The average number of days worked was 220. Coal production totaled 560.8 million short tons, at rates of 2.32 tons per man-hour and 18.32 tons per man-day. A total of 2,779 onsite officeworkers at coal mines and mechanical- cleaning plants worked 5.2 million man-hours in 1967 without a disabling work injury.

Jan 1, 1972

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining' the potential fur reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By L. Y. Sadler

This report summarizes the findings of a 9-yr research program, sponsored by the U.S. Department of Energy and conducted by the Bureau of Mines, to evaluate refractory liner materials for coal gasifier reactors. Commercially available refractories were exposed to coal gasifier reactor environments, reproduced in the laboratory with a high-temperature, high-pressure test facility, followed by extensive postexposure evaluation. Thirty-six castable or gunnable refractories and cements and 24 refractory brick were evaluated. The behavior of castable refractories reinforced with stainless steel fibers was also examined. Gas environments that were evaluated included steam, H2, CO2, CO, and typical high-and low-Btu gas mixtures. Exposure pressures ranged from 100 to 1,000 psig, temperatures from 5000 to 1,1000 C, for periods from 50 h to 2,000 h. In some exposures, sodium and/or potassium hydroxide were introduced in order to simulate a high-alkali environment. It was found that intermediate-and low-alumina refractories produced from domestically available raw materials, rather than high-alumina refractories produced from imported raw materials, gave the best service as liner materials and that alkali attack was probably not a serious problem with most refractories. Based on the results of this program, good choices of refractory liner materials for gasifier reactors can be made.

Jan 1, 1984

By D. I. Bleiwas

Bureau of Mines personnel evaluated the potential availability of nickel from 151 deposits in 18 market economy countries and selected 126 for detailed analyses. An evaluation was made of tonnage-cost relationships indicating the quantity of nickel available at various total costs of production expressed in dollars per pound nickel, including a 15-pct rate of return on the invested capital. The 126 deposits studied contain approximately 73 million metric tons (t) of nickel. An estimated 52 million t is available from laterite deposits, of which less than 2 pct could be produced at $3.50/lb Ni, about equal to the average published price of nickel in 1981. Approximately 21 million t of nickel is available from sulfide deposits, of which about 10.0 million t can be produced at $3.50/lb. Sensitivity studies performed for both laterite deposits and sulfide deposits indicate that the total cost of nickel from laterites is most sensitive to increases in energy costs, and that sulfides are most sensitive to increases in labor costs; sulfides are also sensitive to changes in byproduct revenues. In 1983 the Nickel Mountain mine in Oregon was the only U.S. producer, though development continued on the Gasquet property in California. Of the total 5.1 million t of recoverable nickel in the United States, about 20 pct is available at or below $3.50/lb.

Jan 1, 1984

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

By M. C. Irani

This study is a survey of supply and demand for minerals, metals, alloys, and compounds used by the chemical industries in the Ohio River Basin (ORB) area of Ohio, Pennsylvania, and West Virginia during 1967. Data for the study were obtained from completed questionnaires received from chemical manufacturers and from interviews with officials of chemical companies and mineral producers and distributors. The information includes kind, quality, quantity, values, sources, specifications, uses, and methods of transportation. Results of the study show that of the total value of mineral materials consumed by the chemical industry, manufacture of inorganic chemicals consumed 46 percent; fertilizers, 22 percent; and soaps and detergents, 19 percent. Fifteen commodities accounted for 91 percent of the total value of mineral materials consumed. Five of these--phosphates, potash, salt, sulfur, and titanium dioxide--accounted for 59 percent of the total.

Jan 1, 1970

By H. A. Dierks

Implementation of the joint Federal-State control program established in 1955 to cope with the mine water problem in the Pennsylvania anthracite region is described in this report. The increasing severity of the water problem in the anthracite mines has necessitated major adjustments as this continuing program has progressed. Since 1941 the Federal Government has recognized the mine water problem as an important factor in the worsening economic condition of the anthracite region by initiating scientific and technologic investigations and establishing the Anthracite Flood-Prevention Section in the Bureau of Mines in 1948. On the basis of comprehensive investigations and studies, the results of which were published in numerous reports and bulletins, the Anthracite Mine Drainage Commission of the Commonwealth of Pennsylvania formulated a plan that served as a background for legislative action in 1955, resulting in Public Law 162, 84th Congress (Act of July 15, 1955 (69 Stat. 352; 30 U.S.C. 571-576)), for the Federal Government, and Act No. 82 of the General Assembly, July 7, 1955, for the Commonwealth of Pennsylvania. The report covers 29 mine flood control projects approved and executed in implementing the aforementioned legislative acts. Essential engineering and cost details for each project are given, together with an evaluation of the effect that the installed facilities have on alleviating the mine water problem as it concerns individual mines and the anthracite industry as a whole.

Jan 1, 1962

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By D. Harrington

The record of fatalities from mine explosions during the past 2 fiscal years has been anything but encouraging; more men were killed by explosions (379) than were killed from the ante cause during to' preceding 6 years combined (368). The reason for the large increase in the number of explosion fatalities during the past 2 years as compared with the previous 6 years is not entirely clear. In some instances, there has been laxity in the enforcement of State mining laws; in others, both workers and operating officials is have failed to observe recognized precautionary measures to prevent explosions. In many of the explosions that lave occurred within the asst few years in mechanized mines it has been evident that speed of operation and a demand for maximum tonnage at minimum cost resulted in neglect of ordinary safety measures.

Jan 1, 1942

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state-of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-term underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results froman extensive series of Schmidt Hammer tests found that the shotcrete increased in strength by 70% during the humid summer months.

As part of its research and development activities concerning coal mine operational/emergency communications sys terns, the Bureau of Mines commissioned several contractors to conduct electromagnetic (EM) noise studies and measurements that would aid the development of improved coal mine operational/emergency communications systems. The bulk of the noise studies and measurements were conducted in 1971. The Pittsburgh Mining and Safety Research Center (PMSRC) inherited the responsibility for monitoring the electromagnetic noise activities by mid-to-late 1971, and initiated a review and evaluation of the current and planned electromagnetic noise work. Arthur D. Little, Inc., (ADL) was asked by PMSRC to assist it in performing this review and evaluation by placing stronger emphasis on certain tasks of existing Contract No. H0122026. This technical memorandum report presents the findings, conclusions, and recommendations of our review and evaluation of the electromagnetic noise measurements of the five contractors we were asked to examine. Our review and evaluation effort included meetings and telephone discussions with technical staff of each contractor; serving as Technical Discussion Leader of a "Contractor's Round Table Meeting on EM Noise, Surface and Subsurface, Operating and Non-Operating Mines" called by the Bureau of Mines; examination and discussion of contractor reports and relevant open literature; sample verification calculations; and the documentation of our findings, conclusions, and recommendations by this report.

Jan 1, 1972

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on Manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By M. I. Copeland

The investigation of the iron-gadolinium phase diagram is part of a project undertaken by the Bureau of Mines and sponsored by the Atomic Energy Commission to investigate rare-earth alloys. Data from the investigation of the iron-gadolinium phase diagram revealed a single eutectic system with very limited terminal solubility and three intermediate phases. The eutectic point occurs at about 85 percent gadolinium, and the eutectic isotherm, which occurs at 850° C., extends from the compound Fe2Gd to 99-plus percent gadolinium. Very little solubility of the solid phases in each other was observed. The three intermediate phases, FegGd, Fe3Gd, and FeaGd, melt incongruently at peritectic isotherms at 1,320°, 1,150°, and 1,080° C., respectively. The crystalline systems of the three phases were determined as follows: FegGd, hexagonal; Fe3Gd, hexagonal or rhombohedral; and FeaGd, face-centered cubic. No lowering or raising of the alpha-gamma iron transformation at 910° C., the gamma-delta iron transformation at 1,388° C., or the gadolinium transformation at 1,262° C. was observed. The principal methods used in determining the iron-gadolinium phase diagram were melting-point determinations, thermal analyses, metallographic examination, and X-ray diffraction analyses. Melting, heat treating, and thermal analyses were conducted in a vacuum or under a helium atmosphere because of the avidity with which oxygen combines with gadolinium at elevated temperatures. A few hardness values were determined, but they had no part in the derivation of the phase diagram. No other mechanical properties were determined.

Jan 1, 1962

By B. J. CROSS., Henry Kreisinger, John Blizard, C. E. Augustine

This bulletin presents the results of 36 tests made on a 468-horsepower Edge Moor boiler fired with pulverized coal at the Oneida Street Station of the Milwaukee Electric Railway & Light Co., Milwaukee, Wis. The tests were made by the fuel section of the United States Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation. Illinois coal was used as fuel; the furnace, burners, and feeders were designed by the Locomotive Pulverized Fuel Co. The object of the tests was to determine what over-all boiler efficiency could he obtained with pulverized coal under various conditions of furnace operation and with coal of different fineness and moisture content. The investigation was thorough. The pulverized coal, as it was supplied to the furnace, was weighed in specially designed tanks placed on platform scales. Twenty-nine of the tests were of 24 hours duration, three of 16 to 18 hours, and four of 12 hours. All tests are reported excepting two-8 and 20-which had to be stopped abruptly, No.8 because a motor actuating the coal-feed screw burned out and No. 20 because of trouble with the feed pump. Tests 1 to 27, inclusive, were made with round burners and tests 28 to 3Rwith spreading burners. In the first nine tests a large excess of air was supplied in an effort to prevent the ash fusing at the bottom of the furnace. In tests 10 to 16 the supply of excess air was reduced in order to get a high efficiency, regardless of the slagging of ash at the furnace bottom. Tests 17 to 27 were made with a water screen about 10 inches above the bottom of the furnace, to make possible the burning of coal with a small supply of excess air without the ash fusing at the bottom of the furnace. Tests 28,29, and 30 were made without the water screen and with a small supply of excess air, and tests 31 to 38 with a water screen around the walls near the bottom of the furnace. Tests 32, 33, 34, and 35 were run with coarser coal than that used ordinarily at the plant. Tests 36,37, and 38 were made with undried coal.

Jan 1, 1923

By P. H. Mutschler

The Bureau of Mines studied the costs of transporting fossil fuels, coal, and residual fuel oil from areas of production to consumer regions. Transportation data were stratified by type of carrier, size of shipment, and distance to determine what general effects these variables have upon transportation costs. Economics of haul for coal exist for longer versus shorter distances, and for larger versus smaller trainload sizes. Tanker and barge transportation of residual fuel oil does not show economies of haul for longer distances. It is shown that tanker size and seasonal variation are primary factors influencing the cost of shipping. Railroad transportation data show that coal from western coalfields could be competitive with foreign residual fuel oil in selected midwestern fossil fuel markets. However, the western coal would not be competitive in the New England and the eastern seaboard energy markets.

Jan 1, 1973

Confidence in the strength of the U.S. economic recovery was considerably enhanced by third quarter 1983 profits, which showed a 12.8-percent increase over those in the second quarter (table I). Although the increases were not as great as between the first and second quarter of 1983, profits have grown each quarter since fourth quarter 1982. Both total profits and profits per unit of output increased, which the Bureau of Economic Analysis (BEA) attributes to decreases in labor and nonlabor costs (per unit of output), as well as to moderate price increases. [ ] A number of durable goods sectors, however, continue to show profit declines, especially electrical and non-electrical machinery. Profits in the primary metal industry are still negative, but the economic picture of this industry is improving. Between the second and third quarters of 1983, capacity utilization increased somewhat in primary metal manufacturing and stone and earth mineral mining but did not change at all in metal mining. Capacity utilization in metal materials increased from 47.4 percent in the fourth quarter of 1982 to 64.2 percent in the third quarter of 1983 (table 2).

Jan 1, 1983

By H. B. Jensen

STUDY of the thermal-solution process was begun by treating crushed oil shale in a small autoclave at temperatures of 700° to 950° F. The effect of temperature, reaction time, type of solvent, and richness of shale upon the amount of organic matter that was removed from the oil shale was thus determined. Following this orientation work a semicontinuous, bench-scale apparatus was built so that heated solvent could be pumped through a bed of shale under elevated pressure, thus removing the converted organic matter from the spent shale. After some operating experience had been gained, a continuous unit was constructed. This permitted treating a slurry of shale oil and pulverized oil shale at about 300 p. s. i. and temperatures of 750° to 850° F. for various retention times. Considerable cracking and polymerization of the shale oil were found to take place during the process. In an attempt to prevent this, a study was made of extraction of the shale in batch-type autoclaves under high partial pressures of hydrogen at total gas pressures of as much as 4,300 p. s. i. at 850° F. The thermal-solution process was found to convert over 90 percent of the organic matter in oil shale to oil and gas. The highest yields of gas and oil obtained without hydrogen pressure were equivalent to 119 weight-percent of those obtained from the same shale by Fischer assay. With a high partial pressure of hydrogen, yields equivalent to 126 weight-percent of Fischer assay were obtained. However, the oil produced by thermal solution has a higher boiling range than that obtained by other retorting methods, particularly so if the thermal-solution process is used without a high partial pressure of hydrogen. Nondistillable oil (all benzene-soluble material that would not distill under 2 mm. Hg absolute pressure without cracking) equivalent to over 100 percent of the organic matter in the shale was obtained without hydrogen pressure in the system. When the process was carried out under hydrogen pressure, the yield of nondistillable oil amounted to 60 to 70 weight-percent of the organic matter. Part of this heavy material is formed partly by polymerization and condensation of the shale-oil solvent used. These reactions, as well as cracking of the solvent to form gas and a carbonaceous deposit on the shale, are unfavorable features of the process.

Jan 1, 1953

By R. Barany

This report contains the results of experimental work conducted by the Bureau of Mines to obtain the heats of formation at 298.15° K. of analcite, dehydrated analcite, lawsonite, anorthite, hexagonal anorthite, and leonhardite. Thermodynamic data for these minerals have applications in ceramics, extractive metallurgy, and particularly in geochemistry. Except for data on anorthite, no previous similar data existed. The present results will be a substantial aid in deriving the temperature-pressure-equilibrium relationships among these minerals. The heats of formation were determined by solution calorimetry, with hydrofluoric acid as the reaction medium. The results were expressed both in terms of the constituent oxides and in terms of the constituent elements. The heat of formation data were combined with related entropy values to obtain the free energies of formation at 298.15° K.

Jan 1, 1962

By N. T. Lowe

This Bureau of Mines publication presents salient deposit information in abstract form on 119 principal mineral deposits in the State of Nevada. Commodity coverage addresses 17 critical and strategic commodities that appear to have commercial production potential in the State. The core of the deposits described is taken from those properties evaluated d under the Bureau of Mines Minerals Availability Program (MAP); additional deposits are included to provide a more complete coverage. Institutional and infrastructural factors affecting mineral development are also discussed.

Jan 1, 1985