Search Documents

By Jason Rock, Rob Thompson, Lee Julian

Reactive ground is ground that undergoes a spontaneous exothermic reaction after it comes into contact with nitrates. This is commonly caused by inert rock hosting sulphide minerals, such as pyrites that act as the reagent. The presence and subsequent rate of reaction with nitrate based bulk explosives can be difficult to predict. Once identified, only explosives that are tested and proven to be compatible with the reactive ground may only be used. These typically take the form of inhibited ammonium nitrate emulsion blended with a limited volume of ANFO or porous prilled ammonium nitrate (PPAN) to ensure that all AN prills in the blend are wholly encapsulated and thus protected from the reactive ground. The requirement for high emulsion content bulk products limits the suite of products available for use to high energy, and high expense products. Further, if chemically sensitised products are used, charged holes must be left unstemmed to allow for gassing to occur, adding delay and exposing the blast crew to an unconfined charge in reactive ground. A range of inhibited products has been developed that are solid sensitised and can be bulked to as low as 0.9 g/cc (56.2 lb/ft3). The use of a solid sensitiser enables stemming to occur immediately after each hole is charged, confining any unplanned detonation more safely within the rock mass. The effective and precise manufacture of bulked inhibited products required a new and innovative Mobile Processing Unit (MPU) design. This MPU required the ability to blend two solid raw materials (AN prill & sensitiser) along with two liquid ingredients (AN emulsion and process fuel). This MPU has been designed, manufactured and has used successfully to manufacture low density inhibited explosives. This paper presents an innovative shift in inhibited bulk products with specific reference to their manufacture and application.

By U. Prasad

This paper summarizes the investigation carried out on a wide range of rock types, subjected to high velocity impact to simulate explosive action. A Split- Hopkinson Bar apparatus was used to generate the high velocity impact. The rock samples included both homogeneous and isotropic, and anisotropic types. The strain rate achieved was between 600 and 12OO/sec, The respective measured dynamic compressive strengths were compared with their low strain-rate or static values. It was found that the ratio of the dynamic to static values ranged between 2.5 and 4.6. It was also determined that the high strain-rate loading produced finer fragment size distribution than the static loading. The fragment size distribution from the two strain-rate regimes has been further analyzed to establish correlation with rock types and the strength characteristics. The results also confirm that high strain-rate loading (i.e. high detonation pressure and high velocity of detonation in an explosive column) would significantly affect the degree of fineness in a blast.

Jan 1, 2001

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent, high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptablecomputational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Alan Hooper

This paper and slide presentation is a brief rundown on what is probably the worst natural devastation I have ever witnessed. The epicenter of the quake that so violently shook Mexico City occurred 230 miles away near Mexico's west coast. The first calculation placed the quake at 7.8 on the Richter scale. This was later upgraded to 8.1. Each unit increase on the Richter scale indicates about a 30 fold increase in energy released. The quake was felt in much of Mexico and south Texas and damage occurred in many other Mexican cities. On the morning of September 19, 1985, at 7:18 A.M., the ground went into motion and shook for approximately 2 to 4 minutes. During this period most of the devastation occurred. At 7:38 P.M. the following day, the second quake hit and more buildings fell from this 7.5 quake. The ground in Mexico City moves like jello since it is a dry lake bed 7,350 feet above sea level.\

Jan 1, 1986

By Paul V. Sterk

In the early 1980's, the Homestake Mine converted from labor intensive methods such as open cut-and-fill mining to Vertical Crater Retreat (\/CR) bulk mining and mechanized cut and fill. This transformation occurred as a result of high costs and low productivity associated with open cut-and-fill mining. Use of Vertical Crater Retreat allowed Homestake to contain waste development rock within the mine to further decrease costs since the voids created from VCR stopes provide a good receptacle. The need to access these voids from surrounding development to facilitate waste dumping precipitated the development of drop raising. This system is cheaper than raise boring because it allows drilling into the top of an open stope without the expense of raise boring cutouts or equipment. It's safer than conventional raising since access from the bottom is not required. Two methods of long hole raising or "drop" raising have been successfully developed at the Homestake Mine and can be categorized as Ring Drill Drop Raising using 2-1/4 inch holes and VCR Drop Raising using 6-1/2 inch holes.

Jan 1, 1991

By Clara Godoy, Paulo Couceiro, Juan Navarro

The continuous automatization and digitalization of the different stages involved in any underground construction bring new possibilities to optimize the operation. One of the most important requirements for the development of these projects consist of a proper rock mass characterization for optimizing the stages of the drilling, blasting and support cycle. In the last few years the road to digitalization has gone through data science and big data, showing the importance of data gathered to describe the geological and geotechnical environment that surrounds the operations. Since rock characteristics have an important influence in the drilling response, the technological advances in the sensorization of drilling machinery such as the Measurement While Drilling system (MWD) allow to gather the necessary amount of information to be applied in data science processes to evaluate changes in the rock mass with higher resolution than conventional methods. In this paper, Machine Learning techniques have been used to combine data monitored from the drill rigwith scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure. Considering blasting factors as constant, the model combines the rotary, percussive, hydraulic flushing and the rate of advance of the drilling, and the confinement of the rock mass by depth, to detect zones with different rock properties. This provide an early information of the rock mass condition around the blastholes and the prediction of expected overbreak generated after blasting, being possible to design more efficient bastings, in which each borehole is filled with the right and necessary explosive charge. The analysis comprises data from 57 blasts (around 1700 contour blastholes) and more than 4000 excavated sections.

By Clara Godoy, J. A. Sanchidrian

In this paper, Machine Learning techniques have been used to combine data monitored from the drill rig with scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure.

Feb 1, 2020

By Ann Barron, Mark Abernethy

Regardless of the care exercised by a blaster, seismic and acoustic effects produced by blasting can be disruptive and alarming to many people. With the general trend toward larger blasts, increased population, and urban sprawl, as well as sensational accounts of explosives - related incidents by the news media, fear and concern often leave residents searching for damage to their property. As a result, many blasting companies today find themselves at the center of litigation at an accelerating rate. Obviously, the best strategy for handling vibration and airblast complaints is to operate in a manner that does not create grounds for them in the first place. During the bidding process, ask questions. See the actual site to perf o rm an “exposure analysis.” Collect as many facts as possible before blasting including geological issues, contractual obligations, zoning, historical use of site, disruption of daily life to local residents, demographics of the surrounding area, as well as any unfavorable public opinions or prejudices connected with local construction projects or mining operations. A consultation with local pre-blast firms may assist in tracking down previous problems in the area.

Jan 1, 2004

By Carlos Alvarado, Hernan Narea, Jhon Silva, Bryan Townsend, Katherine Gil, Brayan Caceres, Felipe Pontanilla

With the promising development of new technologies, automation in Drill and Blasting (D&B) is on the horizon. The data generated in all D&B activities, which is currently segregated, can be linked to become information and carry a logical meaning. This information can be used to identify critical activities and make decisions regarding corrective measures to accomplish the goals of D&B. Minera Caserones, supporting Alert2Gain (A2G), and Dyno Nobel, has been working on the development of a quality assurance and quality control (QAQC), system for the mine involving all D&B activities. The main variables in the model for D&B include data from the geology of the deposit, drilling, explosive products, and material loading, among others. To create the model, the mine is divided into blasting polygons. Those polygons are part of a block model. The block model is assembled following different rules, such as: • Block sizes of 4m x 4m x 15m, • Classification of the blocks to a particular blasting polygon using a geospatial intersection algorithm, • Algorithms connect all the pieces of data automatically with the minimum of human intervention and populate the block model, Because measuring data for each block is impossible, another set of rules and algorithms completes the model. Dyno Nobel generates an essential set of data for the QAQC system. Explosive truck loading rates and explosive products, among other data, are also included in the system. The system autogenerates reports every hour, and a summary of the results of each mining day (a mining shift of 12 hours) is distributed by email to all responsible persons to identify the critical tasks and then to make the proper adjustments to accomplish the goals of D&B. The information is updated every hour and available through a dashboard for easy and straightforward interpretation. This paper explains the conceptual details of the QAQC system implemented in Minera Caserones, how the data is aggregated automatically from the different sources, shows examples of the type of information in the dashboard, and presents a successful case where a deviation was detected, and the corrective measures that were implemented to keep the performance of the D&B activity. The paper finally discusses the next steps toward an autonomous D&B system based on new AI technologies, with minimum human intervention.

Jan 21, 2025

By Lon Santis, Michael Swisdak, David Leidel, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc (APT) have developed and released a quantitative risk management tool, IMESAFR (IME Safety Analysis For Risk), for the commercial explosives industry. Consequence algorithms in IMESAFR are considered state-of-the-art. Generally, they mirror those in SAFER (US Department of Defense Explosives Safety Board quantitative risk management software). The science behind the software has now been assessed for its maturity. Results have identified areas where additional test consequence data could improve predictions. To address these areas, full-scale testing programs to provide the needed data have been formulated. Proposed testing efforts include work to: (1) improve characterization of explosive articles now absent from SAFER, and (2) refine modeling of the Potential Explosion Site (PES) types, particularly small metal structures, also not found in SAFER. Goals of each program as well as requirements for conducting the tests have been established. Testing results are to be used to improve the algorithms and to further the state-of-the-art in risk-based explosives safety.

Jan 1, 2012

By Donald C. Clark

The Blasting Contractor as an Insurance Risk involves a discussion of changing times in the insurance market and changing methods of operation in the construction industry. Since the advent of Internal Revenue Service~1 and Occupational Safety and Health Act~2 regulations by the Federal Government in the early 1970's, operations have changed. Many small users of explosives have discontinued any use in favor of subcontracting the drilling and blasting to specialists. This change in operations along with the change in the insurance market has created coverage problems which is the subject of discussion of this paper. Although no definite conclusions are reached, it is an attempt to promote understanding and further the efforts toward equitable solutions.

Jan 1, 1977

By Mohammed Alkazimi, Katie Grantham

The purpose of this paper is to quantify the risk to both the environment and surrounding infrastructure from a pipe sealing implosion. Both accuracy and the precision in determining how a submerged infrastructure damaged by underwater explosions performs provide better decision-making capabilities for managers facing impending oil spills. This determination is vital, especially for both emergency and crisis management teams, as categorized consequences based on both the nature of the structural layout and the surrounding marine environment assist in identifying whether or not the utilization of this technique is applicable. Thus, the decision maker’s aim, in a crisis, is to minimize any associated risk that might result in aggravating the situation by endangering both the infrastructure and marine life. Therefore, the resulting risk matrices will enable technical personnel who are not experts in explosive technologies to be armed with the information necessary to determine if this mitigation technique is applicable to their situation.

Jan 1, 2013

By Andrew P. Ritter, James W. Reil, Douglas A. Anderson, Stephen R. Winzer

We have developed a method for predicting and controlling ground vibration from blasting using a rigorous scientific approach. The method is based upon the superposition of seismic waveforms generated by a single-hole free-face shot, recorded at seismographs deployed in an array that includes environmentally sensitlve locations. Waveforms generated by single-hole shots are shown to be reproducible. The waveforms for each of the sites are used to construct synthetic seismograms for delayed shots based upon linear superposition. A computer code systematically constructs the seismograms for the delayed shots, with incremental delays between holes of 1, 2, or 3 milliseconds (ms). A Fourier amplitude specs-rum is calculated for each synthetic seismogram and the spectra are plotted on a map in delay-frequency space, i.e., each row of the map represents the Fourier spectrum for a blast with a particular delay interval. For single-row shots, the delay between holes in a row is used; for multiple-row shots, the delay between holes In a row is kept constant and the delay between rows is incremented. Predicted vibration varies strongly as a function of delay and h

Jan 1, 1985

By David E. Siskind

U.S. Bureau of Mines Report of Investigation 8507 was published in 1980. In a comprehensive analysis of all known blast damage studies plus new definitive data, the USBM authors adopted new safe level criteria of 0.5 & 0.75 in/sec for the frequency range corresponding to structure resonances. These were 3 to 4 times lower than the existing limit of 2 in/sec and are the most restrictive scientifically-based blasting criteria for the prevention of threshold hairline cracks in homes. The Bureau's own tests involved 76 homes in six states. In USBM RI 8507, those tests were combined with data from nine other studies from the US, Canada, Czechoslovakia and Sweden in an overall conservative summary analysis intended to preclude blasting damage.

Jan 1, 1998

By Joshua Micah Hoffman, Lifeng Li, Jhon Silva-Castro

Since millisecond detonators were first introduced, at least two variables among others have been more closely considered when timing a mining blast; the accuracy and the precision of the initiation system. Unfortunately, those variables are often ignored when designing timing for mining blast. Despite the lack of consideration of the characteristics of the initiation system, in some situations, e.g., firing a blast hole with one deck and two detonators, changes in the blasting sequence can be the results of the overlapping between blasting charges. The consequences of such overlapping involve flyrock events, fragmentation and diggability problems, and other difficulties affecting the operation of the mine.

Jan 1, 2015

By Sam Oaks, David A. Smith

The new Corridor "G" Federal Highway Project in Logan County, West Virginia is the largest mass excavation highway project currently being built in the United States. Seven sections covering 14 miles of four lane highway and two connector roads will require over 30 million cubic yards of excavation. Construction is on a fast track schedule requiring the contractors to complete excavation and pavement placement in a little over 19 months. The two different general contractors have implemented several innovative Blasting and Excavation Programs to complete this project within the tight completion schedule. The paper expands on some of these unique programs that made the project a reality.

Jan 1, 1994

By Charles G. Wade

In the ensuing years nitroglycerin-based dynamites will continually be replaced by water-based explosives. Until recently, the choice of a high explosive water-based product was limited to some type of water gel. Now, there is another choice. New emulsions are available having several degrees of sensitivity over a wide range of diameters. This paper discusses the properties of these new emulsions, e.g., physical and thermochemical; the relationship between diameter and explosive properties; and the effects of aluminum on total energy. There is also discussion of some of the unique properties of emulsions, their advantages, and how they differ from water gels.

Jan 1, 1978

By O Omidi

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper reviews previous experimental information and presents the results of new tests conducted in small blocks constructed using a commercial grout. The effect of the delay on the average fragment size, coarse fragmentation and uniformity of fragmentation is discussed. Fragmentation was coarser at extremely short or extremely long delays, while a fairly constant average size was obtained at a variety of intermediate delays. Uniformity, defined as the slope of the fragmentation distribution through the average fragment size, was poor at short and very long delays and relatively constant at the intermediate delays. Some tests attempted to minimize the effect of gas penetration by lining the boreholes with copper tubes. When this was the case average fragmentation changed marginally, while uniformity was significantly affected by delay and was typically smaller than in the unlined tests.

Jan 1, 2014

By Tony Rorke, Sydney Thabethe

A large overburden blast was carried out at Douglas Colliery, Middelburg Mine Services, close to a national road in South Africa. The road is a busy route between Witbank and Bethal and damage to the road could not be risked. The section of road next to the blast was particularly prone to damage, because it had been mined out on its eastern flank, and the large blast was to take place on its western flank. There were thus three potential damage risks: 1. Fly rock damage to the road surface 2. Vibration damage to the road substrate 3. Damage caused by bulk displacement of the block supporting the road into the void on the mined out side. This paper presents the design and blasting methods used to control the blast and avoid these three risks. Electronic delay detonators were used in multi-decked holes. Signature data were used to determine the blast timing to make sure that delays were used that would provide destructive interference. The timing direction and sequence was decided using wave interference patterns to direct repeated shocks away from the road. The precise detonators and the odelling capability allowed effective control of the blast vibration result. Each hole was charged with two explosive decks separated by a deck of aggregate to limit the charge mass fired per delay and thus limit the reaction forces acting towards the unsupported road. The vibration and blast results are presented in the paper, together with the design that was applied. Details are provided on how the blast was charged and primed. The detonators that were used are described and the timing design is presented.Copyright © 2004 International Society of Explosives Engineers 2004G Volume 1 - Blasting Next to an Unsupported Road Using Electronic Detonators 1 of 13 It is concluded that damage risk to nearby structures can be effectively controlled using electronic delay detonators, provided the appropriate modelling is applied to obtain the most effective delay periods.

Jan 1, 2004

By John Brennan

OK, I’ll admit it: I’ve always been a big Monty Atwater fan. Not only is the man credited with being the father of modern avalanche forecasting and safety in the United States, but he is also responsible for developing the avalauncher. Through its more than 40-year history, the avalauncher has gone through many changes yet continues to prove its worth in avalanche mitigation work.

Jan 1, 2007