Search Documents

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. the contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accommodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problems with a 20-year old steel water main and clay drainage pipe 15 feet from the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By Tuan Nguyen, Dirk Hummel, Ruilin Yang

In a tunnelling site in Japan, it was found that detonators failed to initiate with their shells and primary explosive intact. Their capacitors, however, were discharged due to some damage on the application-specific integrated circuits (ASICs). These detonators are distinctly different from other commonly observed failures, where the shells are rather crashed due to excessive dynamic pressure received from neighbouring blastholes which fired earlier. Such incident has not been reported elsewhere. Detonator failures during a blast are deemed not safe and can cause disruption on the project productivity. It is therefore desirable to understand the origin of such event. Various measurements were conducted to diagnose the problem, but the root cause had yet to be identified. This paper applies a discovery from a 60-year-prior-laboratory experiment and formulates a theory that could explain the observed detonator failure and predicts the measurements and observations.

Feb 6, 2023

By Conny Postupack, Jim Petrunyak, John Hope

The authors discuss the concepts, engineering considerations, and cost relationships involved in the use of drilling and blasting to accomplish backfilling and reclamation with minimum use of mechanical equipment. The four xchods o f reclsnacisn now in use are reviewed, and their advantages and disadvanrages a r e nocea. Guidelines for seleccrng a particular method are offered in terms of applicability under varying geologic, economic, and technological condirions.

Jan 1, 1989

By Ravi Sahu, Kris Jeremiah

This paper aims to study the benefits of using Post Processed Kinematics(PPK) surveying methodology combined with Drone photogrammetry to achieve highly precise positioning (X, Y, Z) of drill holes based on the drill pattern and to highlight innovative workflow of transmitting the drill plan to smart drills for accurate drilling.

Feb 1, 2020

By Patricia Mendoza Watson, Lundquist Robert G

The velocity with which the burden moves after blasting is of concern for safety and economic reasons. Models developed for motion velocity by various researchers were reviewed and likely model parameters were used to develop statistically significant models. Regression analysis and residual analysis were used to determine the model coefficients and the accuracy of the models.

Jan 1, 1990

By Sharon K. Reamer, Yvan Sifre, Klaus-Gunter Hinzen

"Three case studies are presented that illustrate the successful application of firing timeoptimization (hybrid modeling) in the quarry environment and for a construction site. In allcases, the method requires the measurement of at least one in situ, single hole explosion asa representative model of the desired blast design."

Jan 1, 1993

By J P. F Warkentin, A W. Bauer

Recently, significant improvements have been made in both blast design methods and blasting accessories. The introduction of extremely accurate blast delays now allows proper implementation of advanced blast designs. Thus the onus for future blasting improvements has moved from blast design to the need for ensuring that explosives quality is of the highest order. One measurement commonly used to assess explosive performance is the velocity of detonation (VOD).

Jan 1, 1991

By E. A. McCullough, Jackson B. C., S. K. Metz

Public perception is a significant challenge facing the explosives industry. The public often perceives that its needs and interests are in direct competition with those of blasting companies’, leading to conflict between corporations and the community. This misunderstanding lends to unnecessary political and regulatory hardship, and ultimately, social discontent. Although individual corporations implement strategies to address conflict, many of these techniques are insufficient. Consequently, stakeholders resort to expensive litigation. If blasting companies could reduce or eliminate the volume of judicial disputes, valuable resources could be re-directed to more productive activities.

Jan 1, 2015

By Charles H. Dowding

Public concern over blast-induced CRACKING has led to the search for a radically new approach to vibration control. The present system, while scientifically correct, is cumbersome to explain. Historically the potential for blast-induced cracking has come to be described through velocity time histories, which are correlated with observation of crack extension under controlled experimental conditions. Unfortunately time histories are simply too difficult for jurors and village or county regulatory boards to understand. Furthermore these arbiters must accept on faith that the observers were unbiased. Since these public bodies control the manner in which blasting activity is adjudicated and regulated, information must be presented in a form they can understand and that is not subject to second-guessing.

Jan 1, 1999

By Carlos Agreda

The rock blasting environmental impacts such as: flyrock, groud vibrations,airblast,and/or noise, dust and fumes are identified and mentioned. Some comments on the correction factors that might be taken into consideration to calculate the initial velocity and the maximum projection of the rock fragments are mentioned as well.

Jan 1, 1995

By Stanley J. Vitton

An important factor to consider during blast damage investigations is whether the structure was constructed on collapsible soils. Traditionally, these soils have been considered to be soils such as loess deposits, which occur along the Mississippi River in locations such as Vicksburg, MS. However, recent research into collapsible soils has indicated that a number of soils may also fall into this category. A collapsible soil is any soil that is susceptible to large decreases in bulk volume upon saturation.

Jan 1, 1997

By Jeff Yaro, Steven P. Case, Carl Kish

This project involved the construction of a new 4-story library on the campus of Cornell University in Ithaca, New York. The new building was constructed completely below grade, adjoining several of the oldest buildings on the campus. Excepting some surface soil, the job was 100% rock and the excavation had to be completed within a 3-month window.

Jan 1, 1992

By Jeffrey E. Loney, Andrew F. McKnown

Recovery of contaminated groundwater migrating through bedrock can be very difficult due to the low transmissivity of many bedrock fracture systems. To overcome these difficulties, a system of controlled "trench" blasting has been used on several projects to assist in cutting off and collecting groundwater plumes in bedrock. By using a combination of trench blasting and presplitting techniques, linear "fracture" zones are created in appropriate locations to significantly increase flow into recovery wells and control plume migration.

Jan 1, 1995

By John R. Coulson

A survey of federal and state licensing requirements for blasters employed on the surface and underground was conducted for the Bureau of Mines. Subdivisions include surface and underground (large and small), metal, nonmetal and coal. The requirements for certification, class of license, available training, types of testing and enforcement practices are discussed. Included are recommendations of some of the industry trade organizations.

Jan 1, 1980

By Gordon Revey

In construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speed up the work and lessen costs. The process of determining whether or not blasting is practical is ofien complex, particularly when risks are high.

Jan 1, 2001

By William H. Snyer, Victor A. Sterner

A cache of buried explosives was discovered by ICI Explosives, USA Inc. at one of their sites near Gillette, Wyoming. An intensive investigation conducted by ICI management indicated that nitroglycerin sensitized dynamite might be present. Information also indicated that up to 20,000 pounds of explosives may have been buried.

Jan 1, 1997

By J. Esterle, J. Kruttschnitt

Fragmentation modelling in soft rocks presents a challenge due to their propensity to further fragment after blasting during normal handling. Coal and some iron ore deposits are examples of materials that undergo significant degradation during the extraction, hauling and dumping process of the mining operation. The Kuz-Ram model is an empirically derived predictor of size distribution from blasting hard rock. Little breakage occurs during excavation and subsequent sizing of hard rock, so the measured Run of Mine (ROM) size distribution is essentially the same as the post-blast (before excavation) size distribution. However, for soft rocks, each step of the excavation and hauling operation imparts energy to the rock particles so the measured. ROM size distribution will be significantly different from the postblast size distribution. In order to calculate the ROM fragmentation at any stage of the extraction (or sizing) operation, the JKMRC has developed a model that combines both blast fragmentation and degradation through subsequent handling.

Jan 1, 2001

By Francis Otuonye

Rock fragmentation by blasting still remains the most common and cost-effective method of excavating hard rock in mining and tunneling operations. During blasting, the dynamic stresses induced by the detonation of the explosive, in addition to fragmenting the rock in the vicinity of the blast, may fracture the rock at considerable distances from the point of detonation of the explosive. The fractures can result in reduced mine safety, increased costs to support the opening, low productivity and perhaps high ore dilution. Besides the dynamic stresses produced in the rock, air blast overpressure pulses are generated and propagate through the network of underground mine openings. The waves, unable to spread out spherically or hemispherically like blast waves from surface blasting, are forced to propagate by reflection from the roof, ribs and floor down the drift. Blast wave focusing can occur and produce intense shock waves that could damage ventilation barriers such as cement block stoppings.

Jan 1, 1992

By Peter Bellairs, Anthony Bubb

The Porgera Gold Mine is located at an altitude of 3000m in the central highlands of Papua New Guinea some 600 km Northwest of Port Moresby the capital city. Access to the mine is via a five hour trip on an unsealed road from Mount Hagen the nearest regional centre or 40 minutes via air. The mine operates on a fly in - fly out basis and currently produces ore from both opencut and underground operations with the former providing the bulk of the mill feed. Opencut mining utilises conventional truck / shovel, drill and blast methods on both 10 metre and 14 metre bench heights with the larger benches being restricted to the stripping areas. This paper presents the strategy used and the results of a blast optimisation process in the opencut that was a joint effort between the mine personnel and the explosives manufacturer/supplier.

Jan 1, 1997

By Thierry Bernhard, Johan Finsteen, Charles Dowding, Mathias Jern

To bring some clarity to how different standards relate to each other a project was initiated within the European Federation of Explosives Engineers (EFEE). The first part of the project was a literature study and a survey including an evaluation of the answers provided by members of EFEE. The results were presented at the International Society of Explosives Engineers (ISEE) conference in Denver 2020 as well as the EFEE conference in Helsinki in 2019.

Feb 1, 2020