Search Documents

By Alan R. Cameron, Alastair C. Torrance

An explosives underwater test facility has been established and commissioned in the Hunter Valley, New South Wales, Australia which allows the measurement of the actual shock and gas energies of the explosive

Jan 1, 1990

By Jack Elorenta

A recent forum of mine operators revealed a continuing strong interest in alternative methods of freeing rock. A Rand Corporation report lists a continuous mechanical machine that would replace drilling and blasting as a priority for mine operators. Meanwhile, mounting evidence documents a dramatic cost benefit in processing where increased blast energy is available. The reasons for this dichotomy may be due to a number of factors.

Jan 1, 2002

By Thomas R. Scotese, John L. Ackerman

The Hanging Lake Tunnel Project represents a major portion of the Glenwood Canyon Project, the last piece of Interstate 70 to be constructed. The project features twin bore, large span rock tunnels and six open cut portal excavations, all excavated by drilling and blasting. This paper presents descriptions of the methods used by the Owner and Engineer to control and monitor the drilling and blasting practices in the tunnels and in the portal areas.

Jan 1, 1992

In situ, most Taconite is heavily pre-fractured; because of the high cost of comminution of taconite, maximum fracture of pre-existing blocks is desirable. Sustained borehole pressure plays a significant role in fragmentation, especially by penetrating pre-existing fractures. The distribution of explosive-induced energy in the burden in three dimensions was calculated. Data on the comminution of single particles was used, with the distribution of energies and the distribution of pre-existing block sizes, to calculate fragmentation for a case study. The calculation agreed well with the measured fragmentation. Sequential comminution events are much more efficient than single ones, and enhanced fragmentation may be possible with alternative blasting practices. Some important factors in the dependence of comminution on energy input are discussed.

Jan 1, 1995

By Douglas Lindsey, Glenn Hazen, Shad Sargand

"With the innovation of computational equipment, an exact analysis of structures as dynamic systems is more approachable. Accordingly, the dynamic system can be established, if the natural characteristics such as the natural frequency and the damping fraction of a system are known. Through dynamic analysis, the response of a structure can be predicted from ground vibration, and it becomes possible to forecast the damage potential to the structure with reasonable accuracy. Most vibration will appear as single harmonic or superposition of waves that consists of several harmonics with different frequencies. A vibration signal can be expressed, therefore, as the function of sine waves. If a signal is periodic, the particular harmonic with the smallest frequency will befundamental and frequency of the others will be multiples of the fundamental frequency."

Jan 1, 1993

By Dale Preece, Stephen Chung

Development of DMCBLAST-3D is continuing and now includes the capability to simulate the detonation of multiple blastholes in multiple rows that make up a conventional bench blast, either in a rock quarry or a surface coal mine. DMCBLAST-3D is a three-dimensional extension of the proven twodimensional rock blast modeling code, DMCBLAST. DMCBLAST has been under development since 1987 and has successfully predicted the physics, mechanisms and results of a number of different types of rock blasting including, coal mine bench blasting, mineral mine choke blasting and underground stope blasting. Substantial effort has gone into the qualification and verification of DMCBLAST by comparing computer code predictions with real blasts in the field. Comparison with field data has also provided significant guidance to the development of the code.

Jan 1, 2002

By Don Houston

Vertical crater retreat mining (VCR) requires initiation methods that minimize debris in the borehole. The use of detonating cord and shock tube detonators eliminates debris that could interfere with subsequent loading operations and avoids the cost of using drilling equipment to clear the debris. The explosive must not be sensitive to the strength of detonating cord used, otherwise timing will be affected. “Slicing and Dicing” of product before “Air mailing” down boreholes may facilitate loading, especially in wet holes, and can result in product surrounding the detonating cord. Cord sensitivity testing confirmed that having the detonating cord surrounded by product significantly increases the likelihood of an energetic reaction. Careful formulation and testing, based on a thorough knowledge of the application and the role of ingredients in affecting performance, ensures reliable initiation and avoids cord sensitivity. The use of certain metallic nitrate salts, even in relatively small amounts, was found to significantly increase the cord sensitivity of watergel formulations. Evidence of increasing cord sensitivity includes increasing amounts of damage to product and packaging, to ejection of product from the test pipe, then cracking of the pipe, followed by deflagration then detonation of the product. Predictably, the likelihood of an energetic reaction increases with product temperature, cord strength, and borehole diameter, while it is inversely related to product density.

Jan 1, 2002

By Muhammad Yamani, Marsell Riviera, Herry Saputra, Rizky Amin

Drill and Blast processes in hot and reactive ground conditions are a severe challenge in mining, especially in the blasting process. Our main objective is safety issues without compromising the blasting outcome. Safety concerns include unexpected detonation, product damage, and misfire. However, apart from the issue of blasting safety, it is also crucial to maintain good results such as fragmentation, loader productivity, and ore dilution control. Therefore, we use a different product selection method to produce a safe and efficient blast. Pit Araren is one of the pits of the Tokatindung Gold Mine Project in North Sulawesi Province, Indonesia, classified as hot and reactive ground conditions that range from elevation of 25mRL temperature could reach to 98⁰C (208,4⁰F) based on actual measurement. The previous practice for blast holes with temperatures above 70⁰C (158⁰F) loaded with the primer that was specifically designed for hot and reactive ground conditions consisting of detonating cord and packages emulsion that specifically formulated to inhibit exothermic reaction then tied in with a combination of non-electric surface delay detonator and detonating cord initiator (short length non-electric surface delay detonator housed in plastic connector).

Feb 6, 2023

By NA NA

None

Feb 6, 2023

By B T. Lusk, John J. Silva Castro

The signature hole method uses a convolution operation to predict the waveform of a production blast based on the record of a waveform produced by a single blast hole. Convolution is a mathematical operation on two functions, (generally the product) to produce a third one. Recent research communication and publications highlight a lack of discussion in the literature about the available methodologies to calculate the convolution for blast vibration prediction. The goal of this paper is to discuss and present in detail for students in ground vibrations from blasting, several techniques to calculate the convolution between signals when the signature hole method is used. Convolution is a straightforward operation when signals produced by each hole are assumed the same, however; variations in the signals from each hole in a production blast require a more complex convolution operation. A graphical procedure is shown in this paper to solve a convolution when signals vary hole-to-hole (as expected in a mining production blast). The graphical methodology was tested using a recorded blast event and the results were compared to the regular mathematical procedure (convolution) and the results from a commercial software used in the mining industry. Results show that the graphical procedure is in agreement with the results from the other two.

Jan 1, 2014

By Uli Leiste

Two papers are presented which examine Air Deck Blasting, one from a computational aspect and the other from a shock aspect.

Jan 1, 2016

By Richard Arsenault

The production of oil & gas from wells requires method of flow from the producing formation into the well bore. Once the well is drilled it will have casing pipe installed to protect the integrity of the well formations and means of delivery to the surface. Once casing pipe is installed it will be cemented in by pumping cement through the annulus of the casing pipe down to the bottom of the well and allowed to flow outside the casing pipe up into the formation.

Jan 1, 2007

By Patrick D. McLaughlin, C Fordham

"The project outlined in the accompanying paper was to densify beach sands on the pond side ofa tailings dyke to the strength required for future dyke construction, This was to be achievedthrough the detonation of relatively small explosive charges in the sand to cause settlement intoa denser state."

Jan 1, 1992

By Zoltan Susanszky

The total available energy in an explosive charge is seldom fully utilized in industrial operations. For this reason more explosive is normally used to perform a job than we would calculate. In an explosive detonation some energy is generated as waste energy which can not be efficiently used. This results in added expense and possible environmental damage. This waste energy can create problems in metal forming with explosives and during commercial underwater blasting operations.

Jan 1, 1976

By Michael Louis, Charles Dowding

Concern over construction vibration-induced cracking has led to development of a new approach to vibration monitoring called autonomous crack measurement (ACM) and illustrated in Figure 1. This paper describes the concept as well as sensor performance in the first test house fitted an ACM system. Response of three cracks in this concrete masonry unit (CMU) house was measured as part of the system verification. ACM employs a single sensor that measures both weather-induced micrometer changes in crack width and those produced by habitation and ground motioninduced vibration. This comparison is displayed in real time via the Internet without human interaction. Graphic display through the Internet provides a new pathway for communication with the public. Such visual comparison of changes in crack width provides a simple alternative to the present system of comparison of measured and allowable vibration time histories. Measurements reported herein show that weatherinduced response of cracks is greater than that caused by presently allowable construction-induced vibration.

Jan 1, 2003

By Randall M. Wheeler

Pre-blast surveys are used to document the condition of a structure prior to the commencement of blasting activities. They provide the best means of determining the pre-existence of visible cracking and deterioration in a structure before blasting is initiated. A small investment in a good pre-blast survey, coupled with good public relations, could mean a large cost savings for a company in the future.

Jan 1, 1992

By Trevor Garbutt, Peter Bellairs, Jason Sander, Glenn Shaw

The Yarrie Iron Ore mine is located in the Pilbara region of Western Australia some 200km eastsoutheast of Port Hedland, the closest large regional centre. The mine is owned by BHPIO who has contracted a large Australian mining contractor Roche Bros to be responsible for the total mining, crushing and trainloading functions. This paper describes a drill and blast optimisation program, resulting from the introduction of a new emulsion matrix called Titan@ Red used to manufacture both HANFO and pumped emulsion ANFO blends.

Jan 1, 1999

By Joshua Micah Hoffman

While it is easy to state that meaningful involvement of the community can play a critical role for a successful blasting operation, following through with this involvement is not an easy task. Structured Public Involvement (SPI) is a developed protocol for involving communities in project planning decisions and could be readily applied to the blasting industry. SPI was developed for the purpose of collecting quality public input about public transportation projects. The purpose of SPI is to bring about stakeholder satisfaction with potential projects by allowing controlled input from the stakeholders. It was designed and intended for democratic societies that have come to expect a voice in public projects. While blasting operations are not always in the domain of public projects, the fundamental process outlined by SPI can be useful for collecting feedback from the immediate public around blasting operations.

Jan 1, 2014

By Jorge Cárdenas, Luis Huaroc, Máximo Cari, Nestor Delgado

In Peru, after four years of pandemic, some mining companies have chosen to install integrated operating centers in central offices where through network technology and video surveillance it allows them to carry out their activities remotely, this has become a disruptive strategy to promote a safer and smarter mining industry. Our fundamental value is to improve the quality of life, safety and well being of our collaborators, that is why we have created the remote blasting engineering control center " Core" that allows us to humanize mining. Core is an integration of experience, security, technology, quality of life and artificial intelligence; it has media technology connected directly to the mining operation, specialist engineers and technical assistants in team they seek to create optimal proposals of drilling and blasting designs remotely that generate added value to customers. In the planning process the team suggests drilling meshes, in the loading process there are optimized, digitized designs and efficiency in the factory trucks finally in the safety process allows us to identify inadequate pipes within the blasting project, deviation of procedures, remote inspections, identify operating conditions to prevent future risks that may arise in the blasting process. The remote communication systems allow you to monitor mining operations remotely to identify and alert any operational or security deviation that was not identified by the personnel present in the operation, as well as to store images in case investigations are required. The results obtained have allowed us to reduce the exposure of personnel to any risk of the mining operation, to optimize times in the activities of our engineers who are in the mining operations since there is the permanent support of centralized specialists to face every challenge that arises in the operation, for the engineers who are in the offices of Core can be very close to the family and do not lose it, and for our customers it is to meet their needs with engineers specialists in the drilling and blasting process, as well as in safety to be able to proactively cope with any deviation that arises.

Jan 21, 2025

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The problem of the maximum depth at which a mine buried in the surf zone or beach zone is a threat to landing vehicles is being studied by Naval Surface Warfare Center (NSWC), Indian Head Division, Naval Research Laboratory (NRL), and The University of Maryland Dynamic Effects Laboratory. The problem was divided into two parts: The first part involves determining how deep a pressure plate mine can be and still detect a vehicle passing over it. This requires determining the distribution of stress within dry and saturated sand when a vehicle passes over a buried mine. The results obtained from that study are presented in a related paper (1). This paper will cover the second part, which entails determining the impulse delivered to the vehicle. This is equivalent to determining the impulse delivered to a plate suspended above the detonating explosive charge and includes an investigation of the distribution of the impulse over the plate. The purpose of the research is to develop a scaling law and/or computational capability which will permit predicting impulse to be expected in the field from tests conducted in the lab. The computational effort is aimed at the development of and confidence in computer codes that can be used to predict stresses and strains in plates due to the detonation of buried mines.

Jan 1, 2004