Search Documents

By S. M. Bradshaw, V. Rocher, L Kabondo, B. Combrink, C. A. Snyders

Media losses are a significant contributor to the operational cost in a dense media separation (DMS) circuit. Of these losses, up to 80 wt% can occur on the drain and rinse vibrating screens. Although these screens are an integral part of any DMS circuit, surprisingly little work can be found in open literature regarding the effect of aperture configuration on the drain rates (draining water and medium). To establish the effect of slot aperture size, experiments were conducted on a 0.6 x 1.2 m vibrating screen with polyurethane (PU) panels at slurry densities between 1.6 – 2.8 kg/L, and volumetric flow rates of 19 – 25 m3/h for both ferrosilicon and magnetite. Results showed that an increase in the volumetric flow rate led to an increase in drainage rate, moisture content and medium carryover. Once an optimum volumetric flow rate was exceeded, a further increase in flow rate resulted in a decrease in drainage rate with a sharp increase in moisture and medium bypass to the oversize stream. An increase in ferrosilicon slurry density led to a decrease in drainage rate with an increase in moisture and medium bypass with each of these rates increasing as the slurry density increased. For magnetite, a gradual decrease in drainage rate was observed with increase in slurry density and volumetric flowrate beyond the screen optimum point. It was found that an increase in aperture size from 0.63 x 8.8 mm to 0.8 x 8.8 mm to 1.0 x 13 mm resulted in an increase in ferrosilicon drainage rate of between 1.3 - 1.8 m3/m2/h depending on the flow rate and slurry density with a reduction in moisture and medium carryover of between 1.0 – 1.2 % and 14.1 – 20.2 kg/t/m respectively. For magnetite, the drainage rate increased between 1.0 - 1.4 m3/m2/h as the slot width increased from 0.63 x 8.8 mm to 0.8 x 8.8 mm while an increase in slot length from 0.63 x 8.8 to 0.63 x 12 mm only resulted in an increase in drainage rate of 0.1 - 0.5 m3/m2/h.

Jan 1, 2018

By O. D. Khmelnitskaya

The research on selecting of an efficient technology of pyrite cinders complex treatment, sulfuric acid production wastes, have been made. The grades in the initial product were 2.04 g Au/t, 35.0 g Ag /t, 0.38%Cu, 1.1% Zn. Laboratory tests on cyanide technology, thiourea and sulphite leaching were carried out. Magnetic and flotation beneficiation and biohydrometallurgical technology were tested. After considering the results of the tests, the most economically efficient technology of pyrite cinders complex treatment with cyanide leaching of precious metals was determined. The technology involves water washing of soluble copper and zinc compounds, lime treatment and cyanide leaching of gold and silver, detoxification and utilization of mineral wastes. The precious metals are recovered from solutions by cementation onto zinc. Copper is recovered from rinse waters by SW/EW and then zinc is precipitated as hydroxide. All the solutions and organic agent are used in recirculation and therefore the technology is practically waste-free. Mineral wastes can be used as iron-containing materials for cement industry. The technology has been tested in pilot-plant scale under continuous operation with complete re-circulation of cyanide solutions. In this process recovery of 54% Au, 45% Ag, 30% Cu and 50% Zn has been achieved.

Jan 1, 2014

By M. Z. He

Attractive particle interactions which underpin the sliming of gangue mineral particles onto valuable mineral phases are encountered in a number of flotation circuits. Sliming leads to poor flotation recovery of the valuable minerals and high recovery of the gangue particles in the concentrate. To mitigate sliming, low molecular weight poly-electrolytes are commonly used as dispersants during pulp conditioning prior to flotation separation of the valuable and gangue mineral phases. In the present work, the sliming mechanism of sericite onto chalcocite and the influence of interfacial chemistry and two anionic copolymer dispersants (carboxylate substituted polyacrylamide, polymer Cyquest 3223 and sulfonate substituted polymaleic acid, polymer P80) on the sliming interactions were probed in the pH range 5~9. It was shown that the sliming occurred under solution conditions where both chalcocite and sericite particles were negatively charged, as evidenced by their apparent particle zeta potentials. The suspension pH had a profound effect on sliming process as the extent was markedly greater at lower than higher pH. The sliming was found to be due to the chalcocite dissolution, Cu (I) release and oxidation to Cu (II), followed by hydrolysis and specific adsorption, leading to sericite particle surface charge reversal and the formation of electropositive sites on chalcocite surface in the pH range 5~9. Addition of polymer Cyquest 3223 or P80 not only increased the magnitude of zeta potentials of both sericite and chalcocite particles but also reduced the formation of Cu (II) ions and complexes, which mitigated the sliming behaviour. The adsorption of polymer Cyquest 3223 or P80 at 3 g polymer / kg solid or more had a significant impact on the zeta potentials of both sericite and chalcocite particles. Sericite-chalcocite particulate adsorption studies showed that sliming was completely suppressed via an electro-steric repulsion mechanism resulting from anionic polymeric dispersant adsorption at dosages > 3 g polymer / kg solid.

Jan 1, 2014

By Aline Tavares

This paper describes the investigative studies carried out at Vale´s Center of Mineral Development (CDM) for a nickel sulfide deposit aiming to develop an adequate flotation flowsheet. The CDM facilities comprises of very well equipped laboratories to develop hydrometallurgical, comminution, flotation, physical separation processes, besides chemical and mineralogical laboratories, that are required to accomplish pre-feasibility studies, new process routes developments and, eventually, brownfield projects. Close association of the flotation group with the geometallurgy and the mineralogy teams play a key role during greenfield project development. Most of the information required by process engineers responsible for the flowsheet development can be provided by the mineralogy team and its mineralogical laboratory at CDM. During the flowsheet development of this nickel sulfide deposit, two ore types were identified as the most abundant in the deposit, named biotite-chlorite hydrothermalite (HID) and magnetite hydrothermalite (MAG HID). Six samples were selected for the investigative studies based on this initial information. Nickel grade varied from 0.39% to 1.95%. The main nickel-bearing minerals were millerite and pentlandite whereas the main non-sulphide gangue minerals were quartz, plagioclase, biotite, chlorite, actinolite, and/or magnetite. Electron microprobe (EMP) identified the presence of nickel in solid solution in gangue minerals such as biotite, chlorite, and actinolite. Nickel deportment in silicates varied from 3% to almost 40%. Magnesium was distributed in biotite and chlorite, except in sample MAG HID, in which talc was responsible for almost 50% of the Mg content. Liberation studies indicated that the optimum feed grind size was around 150µm and that pyrite occurred highly associated to the nickel sulfides. The flotation tests were planned based on the information provided by the mineralogical data. Rougher flotation tests indicated that the optimum P80 of the primary grind was 212µm for the HID type and 150µm for the MAG HID. From the reagents tested, amyl xanthate proved to be the most efficient in the recovery of the sulfides. In the MAG HID sample talc was well depressed by dosing 600g/t of CMC. Nickel recoveries in the rougher stage were lower than 90% due to the nickel distributed in silicates. However, sulfur recovery was around 95%, indicating high recovery of the total sulfides. Open circuit and locked cycle tests were conducted to evaluate the effect of the regrind size in the nickel grade and recovery (P80 of 44µm and 20µm). Nickel recovery decreased from 70% to 65% when finer regrind size was tested. Although nickel recovery decreased by 5%, the finer regrind size lead to a higher Ni grade (from 11% to 23%Ni) and lower fluorine grade (from 1138ppm to 700ppm) in the concentrate. Keywords: nickel sulfide, flotation, mineralogical characterization, flowsheet development

Sep 1, 2012

The present study is devoted to improvement of the leaching efficiency during phosphorous removal from high phosphorous gravity-magnetic concentrate. Before leaching the concentrate has been subjected to roasting with the addition of either Ca(OH)2 or CaO. The oolitic iron ore is roasted at 900°C for one hour. This reflects in reaction between alkaline earth additive and quartz, aluminosilicates, phosphorus, and some other minor components of the gangue minerals. The application of leaching, physical separation, and wash out of salts has resulted in the decrease of phosphorus from 0.7 to 0.15 % and it is established that the major influencing factor is the concentration of acid and to a less extent duration of the leaching process. About two third of the phosphorus can be removed by roasting with 3 % CaO to hematite, coarse grinding to d50 0.3 mm, dry high intensity magnetic separation and leaching of the magnetic fraction with hydro-chloric or nitric acid.

Sep 1, 2012

By Ying Gu

Automated mineralogy methods and tools, such as the Mineral Liberation Analyzer (MLA) and the QEMSCAN, are now widely used for ore characterization, process design and optimization. Several case studies published recently demonstrate that large gains can be obtained through grinding and flotation optimization guided by automated mineralogy data. However, since automated mineralogy can only provide the information pointing to where the process gains can be made, it does not directly impact the production gain. Thus, a question is often asked: how to value the contribution of automated mineralogy to process improvement of a particular plant. This appears to be a difficult question. On close examination however, it is found that this is essentially a question of the value of information and it is reasonably well documented in various other industries. Hubbard (2010), in chapter 7 ?Measuring the Value of Information?, dealt with exactly this type of problem. The value of information is the reduced risk of an investment and opportunity loss. The methods Hubbard developed can be applied to estimate the value of automated mineralogy, as well as metallurgical test work, which also produces information that reduces the risk of investment. This paper first introduces Hubbard?s theory on the value of information and how to measure it. It then applies his methods to estimate the value of automated mineralogy, using Anglo Platinum?s fine grinding project as an example. In this case, the value of automated mineralogy includes the reduction in investment risk worth US$ 62.5million, in project rejection worth US$197 million and in opportunity loss worth US$320 million. In the end, a general model is developed to allow the simulation of the value of automated mineralogy in different mining operations constrained by different parameters.

Sep 1, 2012

By J. Jirestig

Poor grade iron ore, suffering from interlocked particles, is challenging for any process technology. Extensive grinding is required to attain liberation and to yield concentrates of desired grade. Fine particles are commonly very difficult to retrieve, resulting in value losses to tailings. In this paper, results from HGMS tests on fine to ultra fine hematite are reported. Special emphasis is put on slurry flow velocity. If hydrodynamic drag force, i.e. flow velocity is not controlled and kept constant during the feed and/or rinse phase, fine particles will not be captured and retained. Flow velocity control and constant flow during separation are achieved by discharge valves/slots and parallel magnetic flux and pulp flow configuration. In tests, increased slurry velocity from 178 to 268mm/s caused Fe-recovery to drop from 78 to 48%. Proving that flow velocity control is essential to optimise grade and recovery. HGMS tests at the Metso mineral laboratory on natural (weathered) hematite fines clearly show a large potential to recover valuables, currently lost to tailings. Even at particle size distributions as low as D80=35µm concentrate grades and recovery are very satisfying. Two samples, in-plant desliming rejects (D80=35µm and 50µm) where significantly upgraded and recovered, from 45,3% to 63,6% and 53,0% to 63,4% Fe, at 73,8% and 81,1% Fe-recovery respectively. Other types of in plant rejects, such as gravity separation or WHIMS tailings, also benefits from HGMS separation. Gravity separation reject, 55,8% Fe, at D80=500µm was tested, yielding a magnetic concentrate of 60,8% Fe at 50,7% Fe-recovery. The results indicated that the hematite was poorly liberated. HGMS separation was repeated after a regrind to D80 150µm, resulting in a magnetic concentrate of 62,8% Fe at 75,9% Fe-recovery. The tests prove that hematite, presently lost to tailings streams, can be recovered by HGMS and thereby significantly contribute to improved overall economy. Keywords: HGMS, magnetic separation, recovery of ultra-fine hematite, Indian hematite ores, hematite recovery from tailings

Sep 1, 2012

By A. T. Adema

The cohesive zone, where the ore fed into the blast furnace softens and melts, is critical to the blast furnace performance and stability due to its influence on the gas and solid flow. This paper de-scribes a project for the development of a process model to predict the cohesive zone properties and the results of its first step; the solid flow model. The process model is expected to describe a realistic solid burden flow and the formation of the cohesive zone, its shape, location, structure, permeability, and in particular the mineralogical changes within the cohesive zone. This will be achieved using various simulation and computing tools: a combination of the Discrete Element Method (DEM) and Computational Fluid Dynamics (CFD), the DEM?CFD hybrid approach, together with models for the thermodynamics and reaction kinetics. The key benefits of the hybrid approach lie in the coupling of the continuous phase and the discrete particles, and the possibility of introducing thermodynamics and reaction kinetics into the system in a more realistic manner. Two DEM simulations are presented for a small scale blast furnace to investigate the influence of non-spherical particles on the solid flow. This influence can be observed from a more even solid flow pattern and a reduced deadman size. The results indicate the requirement to include non- spherical particles in a blast furnace simulation to achieve a realistic solid flow.

Jan 1, 2014

By D. Renda

With thise Process of obtaining a solid fuel which is both ecological clean and has a high calorific value by a two-stage method of enriching preferably type lignitic coals to remove a high content of all sulphurs, incuding organic sulphur, which method comprises converting the coal to a semi-coke from followed by magnetic separation. In the Experiments given the best results the washed lignite coal in the West-Turkey, Tavsanli- Region, size -3.35 mm on dry basis. In the microscopic studies of the brigh-thin cross-section taken from the samples of sulfur min-erals pyrite in the dimension of 2~50 micrometers and melnicovite 10 micrometers particles. An thermal treatment an semi-coking themperature between 370°C to 650°C give the best Result of 480 °C. The oxidation and decomposition of sulphur minerals pyrite and melnicovite in lignite coal proceed the iron oxides Fe2O3 and pyrrhotite FeS on the surface layer. The Magnetic Seperator (Rare Earth Magnetic Separator, REMS) is capable this two form of sulphur, including organic and inorganic sulphur, in semi-coke and resulted in the magnetic-fraction in REMS. The non-magnetic-fraction remove total sulphur by 68 %, ash by 44 % and increase the upper calorific value in 15 %. The clean lignitic coal can be utilized in human or energy power stations.

Jan 1, 2014

Domestic production of pyrite cinder reached 15.95 million tons in 2006. The pyrite cinder used in cement industry accounts for about 30% production. The remaining 70%, 11.17 million tons, was thrown away as waste, which brought serious environmental and resource problems. A new technology of composite pellet reduction-roasting and magnetic-separation (CPRM) has been developed to utilize pyrite cinder. Pyrite cinder sample, containing 45.56% Fe, 0.19% Cu and 1.45% S, was pelletized with addition of 5% composite agent in balling disc. Green balls after drying were reduced at 700~800 ? for 20min with 300kg/t pulverized coal injection in rotary kiln. After two stages of ball-grinding and four stages of magnetic separation, high grade magnetite concentrate with 66.23% Fe was produced, meanwhile impurities Cu and S was decreased to 0.048% and 0.053%, respectively. And iron recovery of 73.32%, desulphurization of 96.34% and decoppering degree of 74.73% were achieved. Key technique is that composite agent can accelerate reduction of Fe2O3 and transfer copper and sulphur into water-soluble inorganic salts, which can be removed during wet magnetic concentration. This new technology can be used to fully utilize pyrite cinder and produce high quality magnetite concentrates as feed for steel industry, which will help tackle the pollution problem of pyrite cinder and extend iron-bearing raw material sourcing for Chinese steel industry.

Jan 1, 2014

By Jyotirmoy Sarma

The surface-active agent, like sodium humate, in the present systems produces a very stable suspension. Saline water up to 15% is used as a flocculating agent for recovery of water from the dispersed phase containing 1% solid. The recovered water in the presence of humate at different concentrations (0.05-0.2%) and at pH 8 also produces a stable dispersed phase of iron ore fines and tailings. The beneficiation techniques adopted in the present systems can increase ~ 2-3% iron value in the concentrate of iron ore fine, however, for tailings the increase in iron value is not observed. Keywords: beneficiation, flocculation, iron ore fines, tailings, saline water, surface-active agent

Sep 1, 2012

By L. Q. Luo

SHP-F3200 wet high-intensity magnetic separator (HIMS) was successfully used to separate the complex and weakly magnetic iron ores being composed of specularite, limonite and siderite in Ji-uquan Iron and Steel (Group) Co Ltd (JISCO). It is more and more difficult to separate iron ores from gangues, such as quartz, jasperite and phyllite, as the properties of iron ores gradually become more complicated and refractory. Some technologies have been used to improve SHP-F3200 HIMS, including modifying angle of magnetic polar from 90°to 83°, cooling exciting coils by oil instead of air, adding reverse-washing device to wash off magnetic particles, adjusting the tooth-space of matrix from 5.0 mm to 3.5 mm or 2.5 mm, so as to enhance the recovery of fine iron ore particles. It is still difficult to meet the requirement for recovering more difficultly-separated iron and the demands for high-grade concentrate of iron. In this paper, after analyzing magnetic force exerting on iron ore particles within different separating sections of SHP HIMS, it is proposed to apply the flowing-film technique into the HIMS. Thus a new-type LY matrix is designed to form magnetic gradient vertically, combined with a special flowing-film feeder to improve the existing SHP HIMS. The moving pattern of magnetic particles in pulp in HIMS separation district also has been analyzed in this paper. And the test on the SHP-F700 HIMS shows, under the condition of iron ore containing 30.52% Fe, with particle size of ?0.074 mm accounting for around 75%, if applied with flow-film technique, the iron recovery will be up from 69.45% to 76.07%, by 6.62 percent, with the same grade of concentrates of iron. The calculation of iron yield of every size fraction and the tests showed that film magnetic separation (Film-MS) could promote the iron yield of each size fraction, denoting an excellent result of application of the film technique to SHP HIMS. The mechanism of the film magnetic separation technique is to convert the turbulent flow and disordered movement of dynamic mass particles in the pulp into a directional and ordered laminar flow along the surface of tooth plate so as to strengthen the separation effects.

Jan 1, 2014

By P. S. Dash

With implementation of stringent environmental regulations, ultra clean coal technology development programs have gained significant importance worldwide. As far as Indian scenario is concerned, most of the coals present in India are of drift origin and low grade, containing high mineral matter varying from 15% to greater than 50%. The inorganic or ash constituents of Indian coals are finely disseminated through the organic or carbonaceous constituents so, that commonly used physical beneficiation techniques are of only limited value in affecting separation. Chemical processes involve addition of chemicals, which react with the mineral matter and allow its easy removal. The present study envisages the effect of aqueous alkali leaching followed by acid washing on the removal of mineral matter from two different captive coals of Tata Steel at elevated temperature and pressure. The experiments are conducted at desired conditions using a bench scale pressure reactor set up having proper data acquisition and control system. The research study revealed, that it is possible to reduce the ash content up to 70% by this method. The alkali content of the product clean coal does not increase whereas the silica and alumina content reduces by nearly 58% and 62% respectively. Significant reduction in the phosphorus content is observed after the acid treatment. The crucible swelling number of the feed coal improves after the treatment. The mechanism of demineralisation was evaluated by analyzing the coal samples before and after the alkali and acid treatment using scanning electron microscope (SEM). Because of the acidic nature of the silicates and aluminates, they dissolve into the NaOH solution and form sodalite. Sodalite is partially soluble in the alkali solution. The hydrates formed during alkali treatment are partially removed due to acid wash. This study in overall provides an insight into possible alternative methods of beneficiation for removal of ash from high ash Indian coals.

Sep 1, 2012

By Tohru Kamo, Shigeyuki Katano, Hideki Nakagome, Maiko Adachi, Shingo Nakamura, Kaneshi Taniguchi, Zar Zar Hlaing, Takaaki Wajima

Tantalum capacitor is a small-sized and has large capacity, and is indispensable for electric equipment. The demand increases year by year, and a quite large number of used tantalum capacitors is generated. Recovery of tantalum from tantalum condenser is recently important since production of tantalum have not been stable for the price and the quality. However, recovery of tantalum from tantalum-condenser is difficult since tantalum parts strongly cover with the flame retardant resin made of halogenated compound (mold resin). This research investigated recovery of tantalum parts from tantalum condenser using steam gasification with mixed molten carbonate. Mixed molten carbonate (Na2CO3:K2CO3:Li2CO3 = 1:1:1) (3 g) put into the reactor, and heated with electric furnace while flowing nitrogen (160 mL/min) and steam (1 mL/min) warmed by heater. After heating to setting temperature (450 - 650 oC), tantalum condenser (3 g) was put into the reactor, heated for 5-10 min, and then cooled to room temperature to recover the reacted capacitor by filtration after treating with distilled water. At relatively low temperature (550 oC) heating for 10 min, mold resin can be decomposed by using steam gasification with mixed molten carbonate, in comparison with using pyrolysis and steam gasification without carbonate, and decomposition reaction occurred over 500 oC by using steam gasification with mixed carbonate. Recovery of tantalum parts from capacitor is successful using steam gasification with mixed molten carbonate at 530 oC for 5 min, due to the effective decomposition and removal of mold resin from capacitor. Furthermore, most halogen gas generated from decomposition of mold resin can be trapped in molten carbonate not to exhaust halogen gas. These results suggested that recovery process of tantalum parts from used condenser using steam gasification with mixed molten carbonate is expected as a feasible way to recycle the rare metal in electric equipment.

Jan 1, 2014

By E. Scheepers

The process under investigation is the large-scale production of phosphorus. Gravity delivers the feed, consisting of pelletised apatite, coke and silica (in the form of gravel), to a submerged arc furnace through ten, evenly distributed feed chutes ensuring constant packed bed volume. Within this packed bed, solid-gas reactions are dominant in generating the gaseous product. These reactions, as well as the packed bed itself, were the main focus in the development of a fully three-dimensional CFD model in which fluid flow and energy distribution are represented as functions of chemical reactions, heating and melting of material and heat losses. The associated complex process interactions necessitated the creation of two process-specific, user-developed models that integrates accurate, thermodynamical data with computational fluid dynamics calculations, as well as reaction kinetics. The boundary conditions are provided by industrial measurements, and the key model parameters of reaction kinetics were obtained by laboratory experiments for different feed mixtures. Thirteen temperature probes installed inside the refractory lining of the furnace especially for this project allowed parameter fitting and validation to be guided within the constraints of real measurements. Simulation results reveal a thin, dome-shaped, reductive zone where conditions are optimum for maximum phosphorus recovery, as well as evidence of a thermal reserve zone similar to an ironmaking blast furnace located above this reduction zone. When compared to actual operating data, the CFD model can successfully predict the specific power consumption, the phosphorus in the slag and gaseous product flowrate under given operating conditions. This CFD model forms part of a larger project that aims to create a Dynamic-CFD hybrid control model.

Jan 1, 2014

By M. Ghiani, R. Peretti, S. di Giovanni, G. Zonnedda, A. Serci

"An interesting occurrence of gold bearing ores of economic interest has recently been discovered in the Serrenti- Furtei district, central-southern Sardinia (Italy). The upper part of the orebodies are leaner and fairly porous, and are undergoing intense oxidation processes. In the lower parts sulphide ores predominate, chiefly enargite-luzonite and pyrite and these have a more compact structure. The passage from the oxidized to the sulphide zones, is rather irregular and difficult to delineate. The gold, generally occurring in its native form, is found in small grains. Mineral reserves in the area concerned were originally estimated to total 2.77 Mt: 0.63 Mt of oxide minerals with average gold content of 2.75 g/t and 2.14 Mt of sulphide ores with average gold grade of 3.18 g/t.Recovery of the valuable metals is a complex problem.The effectiveness of a variety of gold extraction techniques has been evaluated conducting tests on batches of ore representative of the different orebody depths obtained from core samples.The techniques investigated were: heap and vat leaching; flotation and flotation followed by leaching of the flotation tailings. The findings indicate that:• the gold contained in the ores in the upper oxidized zones of the deposit can be efficiently recovered by direct cyanidation via heap or vat leaching;• the sulphide ores in the deeper portions, that are not amenable to direct cyanidation but contain enargite concentrations of potential economic interest can be processed by means of flotation to produce a gold/copper bulk concentrate;• beneficiation of the difficult-to-treat minerals contained in the transition zone requires some knowledge of their intrinsic properties. A distinction should be made between the ores containing minor amounts of enargite which appear to be amenable to vat leaching and those with relatively higher enargite content which are processed using bulk flotation of the gold and copper minerals followed by vat leaching of the resultant tailings."

Jan 1, 2003

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper, molybdenum, rhenium and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2014

By Q. Zhang

Phosphate tailings through Flotation contains large amount of dolomite which is difficult to be separated from apatite. In this present research, phosphate tailings is recycled by Flotation i.e. re-processing. High-purity dolomite with purity as high as 91.17% is seperated, which contains 19.82% of MgO. The results of orthogonal test show that the effect of various levels of different factors on the high-purity dolomite floatated. Future utilization of purified dolomite is also discussed: magnesium fertiliser especially magnesium phosphate is expected to be an ideal product from high-purity dolomite.

Jan 1, 2014

By Rogerio de Oliveira Baldoino

The sedimentary phosphate deposit of Bayovar is located in a very dry area of Peru (desert of Sechura) which is close to the Pacific coast. It consists of seven superposed layers (beds) which call for different strategy of concentration. The ore is composed predominantly by apatite (84% in weight basis) plus silicates (16%). In order to treat the ore from beds 1-5, a suitable standard mineral processing circuit (composed of scrubbing, screening, attrition and desliming) started its operation in 2010, yielding 3.9 Mt/y of concentrate assaying 30% of P2O5. To concentrate phosphate from beds 6-7, however, it is necessary to carry out further cationic reverse flotation of silicates, at neutral pH, to yield a concentrate, which meets market specification. The new process was developed in laboratory scale by a collaborative program conducted between Vale S.A. and the University of Sao Paulo-Brazil. A pilot plant has currently been running in order to confirm the very good results yielded in laboratory scale. The successful accomplishment of flotation in the current beneficiation flow sheet will enable a capacity expansion of 1.9 Mt/y of concentrate assaying 30% of P2O5. As water resources are very limited at Bayovar region, all the steps of concentration, including flotation, must be performed with seawater, which must be continuously recycled. This work addresses some relevant topics related to the use of seawater in the reverse cationic flotation of silicates: influence of temperature, water quality (ageing and chemical composition) and collector type (ether amine versus condensate). The results indicate that condensate amine works better than ether amine. If flotation is conducted with the former collector, the separation process is able to tolerate changes in temperature (25-40oC) and water quality caused by either evaporation or ageing. Keywords: phosphate, flotation, seawater, temperature, ageing, concentration, salt

Sep 1, 2012

By P. Bevilacqua

In this paper the possibility to complete the copper recovery and to enrich in PVC a mixture of plastic granules obtained by grinding electrical cables are investigated. The recovery of a large part of the copper still present among the plastic granules was possible by means of a mechanical screening, the finer polymeric fraction was collected, at the same time. In order to complete the copper polymer separation the following techniques were employed. Counter current separation in water, static dense medium separation with zinc chloride solution and copper extraction with nitric acid and subsequent electrolytic deposition. A Tri-Flo® dynamic dense medium separator was employed in order to separate the lighter polymeric fraction, from the heavier polymeric fraction, mainly PVC. Water or a salt-water solution was employed to feed the separator device.

Jan 1, 2014