Search Documents

By Haghi. Hamed, Javad Vazifeh Mehrabani, Mehdi Sedigh

In this investigation, the possibility of physical separation methods such as attrition scrubbing, hydro-cycloning and also reverse flotation were investigated for silica and calcite removal from relatively low grade kaolin. The head sample was provided by the Iran China Clay Company and the major oxides contained in the head sample were Al2O3, SiO2, CaO and Fe2O3 with grades of 15.07%, 71.05%, 4.35% and 0.52% respectively. The liberation degree of calcite and iron impurities from kaolin particles were over 80% for particles finer than 210µm and 53µm respectively. Attrition scrubbing tests were carried out with scrubber cell of the conventional Denver flotation cell model D-12. Laboratory scale hydro cyclone was applied for the beneficiation of kaolin. Attrition scrubbing tests with control screen of 106µm did not achieve the desirable yield for purification of this kaolin sample, but hydro cyclone experiments resulted in better results. Hydro cyclone with 2.54 cm diameter used and the only variable was the cyclone inlet pressure ranging from 68.65kPa to 98.07kPa. The best inlet pressure was found to be 68.65kPa. Based on the optimized condition, Al2O3 and CaO amount in the hydro-cyclone overflow was 23% and 1.47% respectively. However weight recovery of the overflow in each cyclone experiment was less than 30% and multi stages of hydro-cyclones would have to be applied for higher weight recovery and better yield. All of the flotation tests were carried out in the conventional Denver flotation cell model D-12. Reverse floatation tests for calcite removal were carried out under alkali pH based on full factorial design of variables in 2 levels including one center point. The three parameters tested were collector dosage (gr/ton), pH and depressant dosage (gr/ton). The collected data from flotation tests were analyzed and optimized collector and depressant dosage were 1000 gr/ton and optimized pH was 8.5. Under the above mentioned conditions, calcite removal was about 75% and CaO content in the final product was reduced from 4.35% to 1.33%. However calcite removal will increase to more than 83% if the feed particle size in flotation tests is reduced from 210µm to finer than 53µm. Finally after optimization, the best working condition and possible flow sheet were developed.

Jan 1, 2014

By T. Suzuki

Acid leach liquors from spent lithium-ion batteries employing lithium cobalt dioxide (LiCoO2) as a cathode active material contain valuable metals such as cobalt and lithium, as well as common metals such as aluminum and copper. The objective of this study was to develop a hydrometallurgical process providing a high selectively between aluminum, cobalt, copper, and lithium from hydrochloric acid solutions. Batch experiment results showed that selective hydroxide precipitation approach was not suitable because a significant amount of cobalt and lithium was co-precipitated with aluminum and copper hydroxides. In contrast, batch experiments and the subsequent data analysis indicated that the sequence of solvent extraction circuits using PC-88A, Acorga M5640, and tri-n-octylamine (TOA) extractants effectively separates four metals of interest. In the first circuit of the proposed process, copper was selectively extracted by Acorga M5640 at the pH 1.0-2.0. Aluminum, cobalt, and lithium remain in the aqueous phase. In the second circuit, aluminium is selectively extracted by PC-88A at pH 2.0-2.5. For the separation of remaining cobalt and lithium, Acorga M5640 provided higher separation efficiency compared to PC-88A single extractant and PC-88A/TOA mixed extractant. However, the stripping efficiency of cobalt from the Acorga M5640 organic phase was found to be low (less than 10 %). Therefore, PC-88A/TOA mixed extractant rather than Acorga M5640 is an advisable choice for the separation of cobalt and lithium. Keywords: spent lithium-ion secondary batteries, solvent extraction, lithium, cobalt

Sep 1, 2012

By Sanja Miskovic, Manjunath Basavarajappa

In this study, a coupled CFD-DEM (Computational Fluid Dynamics-Discrete Element Method) approach is used to simulate two-phase, solid-liquid flow within the flotation cell. Turbulence plays a key role in flotation cells and level of turbulence is affected locally by the presence of particles. Turbulence in the flow is modelled using Reynolds Averaged Navier-Stokes (RANS) based k-e model. Using particle transport and spatial distribution, mixing mechanism for differed sized particles are analysed. By including the effects of particle-particle collision, particle rotation, and particle translation, as well as the volume occupied by the particles in the fluid, CFD-DEM approach can be used to accurately predict the motion of particles in the turbulent solid-liquid flows with strong coupling. Electrical resistance tomography (ERT) is used to investigate the effect of impeller size, shape, off-bottom clearance and impeller speed on mixing and suspension behaviour inside flotation cell. The effect of flotation impeller design, impeller size, and off-bottom clearance on flow hydrodynamics is investigated. In the case of moderate and high solids loading (> 10 %w/w), energy is dissipated through inter-particle interactions and four-way coupling becomes important (Derksen 2003). The main goal of this study is to understand the effect of particle size and concentration on flow dynamics at high Re in highly turbulent systems using advanced modelling and measurement techniques. Experimental measurements obtained by ERT) system allowed detailed mapping of temporal hold-up profiles of the dispersed phase. Impeller size and off-bottom clearance are found have significant effect on the particle suspension characteristics.

Jan 1, 2014

By Michael Young, Rodrigo Araya, Cesar Gomez, Le Huynh, James Finch

The performance of flotation machines is closely related to the gas dispersion characteristics achieved in their operation. It is known that frothers play a major role not only in the size distribution of the generated bubble population, but also on the swarm rise velocity. A program to characterize frother effects on two-phase hydrodynamics (air-water) of Jameson cells was undertaken in a fully instrumented pilot unit installed at McGill University. Gas dispersion parameters (gas velocity, gas holdup and bubble size distributions) of the gas-liquid mixture generated in the downcomer were measured after its release into the separation chamber. The unit was operated under different conditions including gas velocity, liquid jet velocity and frother concentration (MIBC). Bubble size distributions for concentrations above the critical coalescence concentration (CCC) were narrow with Sauter mean diameter between 0.6 to 1.3 mm. The bubble size followed the general trend as encountered in other types of flotation machines, i.e., rapid decrease with increasing frother concentrations below 10 µL/L, and almost no change in size for concentrations above 30 µL/L. The CCC was between 10 and 15 µL/L. Strong correlations were found between bubble size and air-to-liquid flow ratio (APR), and between the bulk density of the aerated solution in the separation tank and the vacuum inside the downcomer. An equation is proposed to estimate gas holdup in the separation tank from vacuum and bulk density readings.

Jan 1, 2014

By Hong Nguen Vu, Pavla Ovcarí, Peter Fecko, Barbara Tora

The aim of this paper is to evaluate the suitability of a coal sample from the mine Jaworzno (Poland)- locality for bacterial leaching. Laboratory research used a pure bacterial culture of Thiobacillus ferrooxidans. The results showed that bacterial leaching was effective, with a one month leaching time, when 65% of total sulphur and 85% of pyritic sulphur was leached. The paper describes changes to the pyrite during and after bacterial leaching.

Jan 1, 2003

By N. T. Beukes, W. Banda

Recovery of Co from slag is a recent advancement in the extractive metallurgy of nonferrous metals. In this study a DC arc technology at laboratory scale has been applied to investigate the selective recovery of Co from slag, under three different flux types with an emphasis on influencing the activity of FeOx, SiO2 and CoO in the slag. It is known that reduction of slag by carbon is only up to a certain level after which, the recovery will depend on the chemistry of the slag, hence the need to modify the slag chemistry. Two power settings were employed to induce higher temperatures and aggressive agitation. The results were interpreted by comparing how much Co and Fe was in the slag and alloy. TiO2 reduced the amount of Fe in the product alloy compared to when CaO and CaF2 were used. The change in power did not seem to have had a major effect on the recovery although the amount of material lost to flue dust was more at a higher power rate.

Jan 1, 2003

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

Although the cyanidation process for gold leaching has been applied for more than a hundred years, some aspects of it, such as the passivation of the gold and the depassivating action of heavy metals, are still not well understood. In this work the anodic behaviour and surface composition of gold in alkaline aqueous cyanide with lead additions were investigated using polarization experiments and XPS. It was found that lead in the solution activated the gold at low concentrations, somewhat more positive than the reversible potential for gold, but that the activity again decreased at higher concentrations of lead. The potential range for the activation of the gold coincides with that where underpotential deposition of lead occurs, i.e. –200 to –600 mV(SCE), as indicated by the surface composition of the gold, shown in figure 1. Note that the concentration of lead on the surface of the gold only increased with time in the bulk plating potential range for lead, where gold is not activated by the presence of lead. It is also shown that up to 20 mg/L of lead added to the solution will activate the gold, provided that bulk plating of the lead is avoided. It is also important to avoid reducing conditions during leaching, where bulk plating of lead may occur, if the gold is to be activated by lead to achieve a high leaching rate, as the bulk plated lead screens the surface rather than activating it.

Jan 1, 2003

By Alban Lynch, Benigno Aquino, Hakan Dündar, Alexander Kalugin, Marco Delgado, Alberto Palomino, Ali Türkistanli

Dynamic separators are efficient dry classifiers because new designs during the last 50 years have reduced the by-pass and improved the partition curve. By contrast cyclones have been used as classifiers in wet grinding circuits for 50 years but without serious change and the early problems which were caused by high and variable by-pass, and different mineral specific gravities, still exist. High frequency screens are now used for wet separation and the operating characteristics of closed grinding circuits using cyclones or screens are discussed. Data come from circuits at the Condestable, Cerro Lindo, El Brocal and Catalina Huanca mines in Peru, the Eczacibasi mine in Turkey, and the Apatit mine in central Kola Peninsula in Russia. All classifier data are described by their partition curves and all mill data by their breakage rates. With cyclones the by-pass, d50, and sharpness of the partition curve change as operating conditions change but with high frequency screens the values vary little because the by-pass is low, the sharpness is high, and d50 depends on the aperture size. Data from all plants indicate that lower by-pass and sharper separation improve breakage rates and throughputs. An initial model of the screen is proposed.

Jan 1, 2014

By Nani Pajunen, Kari Heiskanen

"Products filling our societal needs, like communication and transportation needs, are becoming more sophisticated and efficient. The cost has been an increased complexity of material combinations. The same trend is also seen in investment goods. As an example, different crusher types have almost doubled the power to weight ratio in a relatively short time while producing even higher crushing rations. This has been possible by high performance materials and advanced designs. Another example is new hybrid materials in prefabricated high-strength steel structures in construction with the aim to lighten the products and obtain energy savings in the use phase e.g. in transportation. This development in general has made the end of life phase obscure. Recycling is often understood as the first phase of the material cycle. This has been supported by the material centric point of view. When, say indium, has been collected and mechanically treated to a concentrated fraction, it is assumed as recycled. This is not the case. The same applies to special steel alloys where one tends to lose some of the alloying elements to slag or even into the gas phase in the melting and refining stage, not in the earlier steps of recycling. At present there is no clear understanding of recycling of hybrid materials and no clear willingness to create new functional recycling systems. As the EU directives and most of legislation worldwide are based on the material centric thinking and implemented even on total mass recovery basis there is neither legislative incentive nor very strong economic incentives to work out the problem. In our research, we focus on industrial design towards sustainability from a product centric point of view from product collection to final metallurgical steps. It is vital, in the design phase of product, to understand the effects of decisions on recyclability to a saleable raw material. Main goal of our work is to create the fortunate circumstances in supply chain - to pass the barriers and find the effective and fruitful drivers - for reasonable use of raw materials and recycling co-operation with industry. The boundary conditions in the work are extractive metallurgical performance and the economic viability of all the steps. It can be shown from our work that small design alterations may have a large impact on the recyclability. The earlier the decisions are made in the product life chain the more positive impact they will have. It can also be shown, that a strong processing and metallurgical industry is vital to any meaningful recycling of the modern EoL products. Finally, it is also question of the individuals and values: supply and demand. Are you ready to take up the gauntlet: demand recyclable products."

Jan 1, 2014

By S. Gomez, P. A. Bebswa, A. N. Mwale

"The research aimed at improving the way screen performance analysis is conducted using a model that accounts for most feed and design parameters in its formulation. Thus, the aim was to validate the fine screen model that was developed at the Centre for Minerals Research (CMR) unit at the University of Cape Town. Fine wet screening is increasingly becoming an important application in fine grinding operations. Minera Saucito, a lead-zinc Mexican mine has replaced hydrocyclones with eight stacks of five decker derrick screens to close the ball mill in their concentrator plant. The five decker stacks have improved the overall plant throughput by 20% and have had the ball mill circulating load reduced considerably. As a continuous plant optimization process, a number of surveys were carried out to assess the performance of the 75 µm panel aperture installed screens. The surveys were conducted at seven different feed rates to the entire nest of screens to collect performance data. Using the fine screen model to analyze the results, it is found that as the feed rate increase, the sharpness of separation reduces. The CMR fine screen model was fitted to these results. The model fits the plant data with good accuracy. Simulated results based on this model are also presented.INTRODUCTION The potential of high frequency vibrating screens has long been identified as an alternative to hydrocyclones in grinding applications (Rogers and Brame, 1985). However, high frequency vibrating screens have had two main disadvantages, low capacity and high wear rates (Kelley and Mckeon, 2005; Teknikk, 2009). Current vibrating screen technology overcomes these challenges by multiple deck screen design and use of wear resistant urethane materials for panel construction (Kelley, 2007; Valine and Wennen, 2002). For a example, the Derrick screen’s material of construction is a tensionable urethane that provide high open area ranging between 35 to 45% with considerably reduced blinding (Valine and Wennen, 2002). Thus, there has been an increased uptake by the mining industry in the use of wet fine vibrating screens closing the ball mill as the final classification stage in the comminution circuit (Barkhuysen et al., 2010; Frausto, Ballantyne et al. 2017; Pelevin and Lazebnaya, 2009; Teknikk, 2009). Even though there is a number of models in existence, none of these models adequately predict the performance of high frequency vibrating screens (Karra, 1979; Rogers, 1982; Subasinghe et al., 1990; Trumic and Magdalinovic, 2011). Recently Mwale et al., (2016) developed a model for predicting the performance of high frequency vibrating screens using the partition curve properties. The input parameters of the model include screen open area (??) in m2, tonnage feed rate (????) (tph) and the weight fraction of solids (??) in the feed for a given panel aperture size. The model was developed based on data collected from a single deck industrial size derrick screen, in a pilot setup. The work presented in this paper is an attempt to test this model using data collected from Minera Saucito concentrator, an industrial plant whose comminution circuit is shown in Figure."

Jan 1, 2018

By Robert Dunne

A review of the current ?state of the art? of refractory gold treatment will be provided. This will include a global perspective of the refractory processes that are being practiced, where they are and some discussion on why the processes were selected. Some discussion on the challenges that face the refractory gold industry will also be provided.

Sep 1, 2012

By V. K. Gupta

Selection of mill size for reducing a feed material of a given size to the desired product size is generally based on the specific energy estimate obtained from Bond test. Over the last thirty years or so, an attempt has been made to develop a more accurate and powerful alternative approach based on the characterization of the particle breakage kinetics and material transport through the mill over a range of operating conditions of interest and correlating the degree of size reduction achieved with the net specific energy input to the mill. Particle breakage kinetics are described in terms of the specific grinding rate and breakage distribution parameters for the individual size fractions. Precise estimates of these parameters and the net energy input to the test ball mill (a laboratory or pilot scale mill) are important for development of desired energy-size correlations. In this context, three tasks are important: (a) preparation of the feed charge, (b) design of batch grinding experiments and (c) computational technique used for estimation of the breakage rate and breakage distribution parameters. This paper highlights several aspects of these three tasks that have been overlooked by researchers working in this field, and describes a more appropriate approach for estimation of model parameters and specific energy input. Several examples are included based on the data available in the literature and those generated in our laboratories to illustrate important points.

Sep 1, 2012

By Alain Broussaud

The lecture is about the growing role and the evolution of advanced process control (APC) in the mining and mineral processing industry, taking into account major trends in Information Technology. It reflects the standpoint of a team, which has already successfully developed APC technology for more than 20 years. Advanced process control systems tend to rely on combinations of artificial intelligence techniques or algorithms that complement each other and cooperate. Each technique or algorithm makes it possible to use certain type of knowledge about the process, so that the advanced control systems benefit at any time from the combined knowledge of process and control engineers and plant operators, from knowledge derived from past research work and process modeling, from a considerable amount of data provided by advanced instrumentation in real time, and from knowledge that can be extracted automatically and at any time from past data and images. The lecture will first review and compare the role, merits and limitations of algorithms that are used for online decision making in mineral processing plants: expert systems, fuzzy logic, neural networks, soft sensors, optimizers, and MPC controllers. The lecture will also review the role of online image analysis and sound analysis in process control. Recent developments in this area open new dimensions, in particular the ability for advanced process control algorithms to automatically explore the past, move back and forth in time in order to make better informed decisions, and the ability to cooperate with the operators for better performance. Applications will be presented. Recent progress in process simulation makes it possible to design, configure, check, and pre-tune APC systems before plant startup, opening new options for implementing APC. In conclusion, the author will share his experience about the key ingredients for sustainable success in APC Keywords: mineral processing plants, APC, MOC controllers

Sep 1, 2012

By T. C. Rao

This presentation identifies how mineral (coal included) processing profession should look at the challenges (threats) being faced by mineral industry. Presently, the focus is more on supply and demand on minerals. In addition, the R&D activities in the chain of mine-to-metal are paying more attention (if not only on) the processes being adopted, development of new equipments and modeling and simulation. But the profession is grossly ignoring aspects such as impact of the processes on other resources, of the ways we extract, use and dispose them socio-economically and efficiently. A business model which may encompass all these dimensions are essential for the sustainable development of mineral industry and a possible approach in this direction is presented. To start with, for the sustainable growth and existence, the profession must be aware of the prospective impacts of their activities on critical factors such as ? political (changing government policies), geographical (environment, land, water and habitat), which have major bearing on the survival and growth of the industry. Mineral Processing professionals have to join hands with mining engineers to answer some relevant questions related to the impact of mineral industry on society. Mining can become economically viable only if mineral processing engineers come out with innovative solutions to reduce capital and operating costs. The solutions have to be adoptable and practically feasible so that industry looks at us for directions. In fact, we have to move towards beneficiation of nano particles striving towards zero waste. Some of the gaps in the knowledge of procedures being followed in the design and operation of processing plants are highlighted. Enhancing the knowledge base for solving unexplored possibilities, solutions to evolve sustainable development measures which demands innovation both at academic and practicing levels is the need of the future. Well-structured academic programmes are to be formulated so that the graduates of these programmes can make an effort to look at processes/concepts with a new insight and approach; the profession should excite the young brains with challenges. R&D funding agencies have to have a long-term perspective on mineral processing so that closer interactions between academic institutes, industry and R&D organizations are sustainable and that innovations are at least a few years ahead of needs of future challenges. Keywords: sustainable growth

Sep 1, 2012

By S. Banisi, E. Arghavani, M. Pourkani, M. J. Rajabi, Gh. A. Mohamadian, H. Bidshahri, Gh. A. Parsapour

The Sarcheshmeh copper complex flotation circuit of plant No.1 consists of two identical north and south sections where each includes four rougher (each bank consists of 14 cells), two cleaners (each bank consists of 8 cells), two recleaners (each bank consists of 2 cells), and two scavenger banks (each bank consists of 10 cells). The reduction of feed grade along with a change in the mineralogical composition is the main reason of current lower concentrate grade (24%) compared with the design concentrate grade (32%). Because of a lower feed grade, the amount of rougher concentrate has decreased which in turn has significantly reduced the feed rate to the cleaner, recleaner, and scavenger banks. This has increased the mean residence time of the material in the cleaner section resulting in a lower final concentrate grade. A laboratory study showed that the final concentrate grade can be increased by 2-4% if one cleaner stage is added to the flotation circuit. In this research, based on the laboratory results, one cleaning stage was added to the current flotation circuit. In order to make this modification instrumentally possible in the plant, the final concentrate was gravity transported to the Mo-Cu thickeners. This released 2 pumps and associated tanks which made addition of one cleaning stage practicable. Finally, a part of the cleaner and scavenger cells were used as the third cleaning stage. This decreased the residence time in the cleaner and scavenger banks. After implementation of one cleaning stage in the south section of the plant, the performance of the circuit compared with the identical north section. It was found that at the same recovery, the concentrate grade of the south section increased by 2.5%. The promising results led to the implementation of adding one cleaning stage in all sections of the flotation circuit.

Jan 1, 2018

By Nirmal S. Weerasekara, Malcolm S. Powell, Mohsen Yahyaei

"An understanding of the fundamentals of different breakage mechanisms is critical for successfully modelling comminution processes. Due to the high frequency of low energy collisions in the grinding process, superficial breakage has a significant role in size reduction in mills. To develop a scaling up methodology for characterising low energy surface damage behaviour of ores, a series of surface damage tests have been conducted using three grinding mill sizes with diameters of 1.8, 1.2, and 0.8 m. Two types of gold-copper ore with different hardness were used: C-ore and T-ore. All tests were conducted using wet mode to remove the products during grinding. To ensure low energy surface damage was the dominant mechanism, in all tests the mill speed was reduced to 40% of critical speed. A surface damage index normalised with product mass and surface based specific energy is determined from the results enabling a study of the grinding performance regardless of mill size, energy level or charge mass. Incremental breakage tests using the JKRBT indicate that the A×b values of the T-ore were 60% higher than C-ore, suggesting the T-ore is considerably softer. The fractional mass loss rate for the T-ore in the 0.8 m and 1.8 m mills started from 16 and 7 (1/kWh/m2) while for the C-ore it was 4 and 2 (1/kWh/m2). After 6 minutes the surface damage index in all tests tends towards steady state a constant value, an indication of steady state surface damage condition. It has been demonstrated that this methodology can be a useful basis for characterising superficial breakage behaviour of ores."

Jan 1, 2014

By Guanzhou Qui

The utilization status of copper ore resource, the application and development of biohydrometallurgy technology in the world was reviewed. Furthermore, according to the analysis of the characterization of Zambia?s copper resource, biohydrometallurgy technology was shown to be a good way to explore and utilize the enormous low grade copper resource, such as ore tailings and low grade copper ore in this country. Through the cooperation of CSU, China and MMMD, Zambia, ?CNMC-CSU Demonstration Base of Biohydrometallurgy Technology in Zambia? was launched and several biohydrometallurgy plants are being constructed, that indicates the biohdyrometallurgy technology would be applied soon in Zambia and even in the whole Africa. Biohydrometallurgy technology stands as an efficient alternative to the traditional pyrometallurgy process can be the key to unlock mineral resources value. Keywords: biohydrometallurgy, Zambia, copper processing, CNMC-CSU

Sep 1, 2012

By Mojtaba Ghorbannezhad, Abbas Sam, Soroush Arabzadeh

One of the dewatering methods in mineral processing plant is filtration system. Disk filters are included the porous surface with pressure drop on both sides, Water in the pulp passes through the surface and solid particles remain as a cake on it. Wet concentrate production of magnetite processing plant at Golgohar Mining and Industrial Company with solid tonnage of 160 ton per hour and 49% solid amount contains 166 m3/h of water. In the present study, in addition to studying disc filter performance, the effective parameters on cake moisture were studied using Vacuum Bottom-Feed Leaf method (in the laboratory scale). Optimization was performed using the Taguchi method. The results showed that the cake moisture is reduced by increasing particle size and solid percentage (because of specific resistivity reduction), while the rate of cake formation and its thickness are increased. Also, it was found that by increasing pressure, the cake moisture is reduced and cake formation rate and its thickness are increased. In this study, the effect of fabric texture was also examined. Lowest cake moisture was obtained in condition of using compressed plain fabric with mono-multi filament fibres, pressure at 75kPa, solid percentage of 65 to 70, particle size (D80) equivalent to 123µm and disk rotation speed of 1.25 rpm.

Jan 1, 2014

By Erico Tabosa, Kym Runge, Peter Holtham

"The distribution of turbulence in an industrial scale mechanical flotation cell and its effect on flotation kinetics was studied using a fully instrumented 3m³ cell. The cell was operated at a copper concentrator in Australia with different combinations of airflow rates, impeller speeds and sizes and cell aspect ratio providing a wide range of hydrodynamic conditions. An analysis of the overall flotation cell performance showed that the overall copper recoveries were very similar for the conditions tested. However, by decoupling pulp effects from froth effects it was possible to evaluate whether the changes made affected the pulp zone and/or froth zone responses. The analysis showed that the overall recovery has the potential to be up to 7% higher, if not limited by froth recovery. The cell hydrodynamics were characterised by the overall energy dissipation rate and, to understand the distribution of turbulence within the cell, localised measurements were made using a piezoelectric vibration sensor. By comparing the metallurgical performance of the cell with the different hydrodynamic conditions it was found that the collection zone flotation rate constant was not directly related to overall energy dissipation, as is commonly observed at laboratory scale, where energy is usually only changed by varying impeller speed. In this study, energy dissipation rate was varied using not only impeller speed, but also the size of the impeller and the cell aspect ratio. In these circumstances, the best correlation was found to be between the collection zone flotation rate constant and the distribution of turbulence, i.e. the size of the turbulent zone."

Jan 1, 2014

By Xiao Jian Li, Dai Xiong Chen, Jian Wen Yang

In one kind of lead and zinc bearing polymetallic ore containing secondary copper, the characteristic of low sulfur, high zinc, and particularly the existing of secondary copper minerals can lead to lead concentrate with high content of zinc because the dissociation of Cu2+ in the grinding process may have an activation influence on sphalerite. Considering its process mineralogy analysis, a new process of seperation of lead and zinc has been put forward. The experiments focused on the analysis of the advantages and disadvantages of the inhibition effect of traditional adjustment reagent + zinc sulfate on activated sphalerite compared with new organic inhibitor, polysaccharide xanthate. According to the numerical calculation and test results, a reagent system of polysaccharide xanthates is developed, which has a good inhibition effect on Cu2+ activated zinc minerals, achieving high-efficiency separation of lead and zinc. A new reagent system and flotation process was developed under optimal conditions. Under the condition of the run-of-mine ore containing 2.37% Pb and 12.48% Zn, lead of 67.69% grade and lead concentrate with the recovery rate of 86.06%, zinc of 60.32% grade and zinc concentrate with the recovery rate of 96.15% were achieved.

Jan 1, 2014