Search Documents

By D. Chakraborty, Neeraj Kumar

"The study provides the comparative analysis of the performance of water only cyclones and hydrocyclone for iron ore fines processing at Joda Iron ore processing plant, Tata Steel. Joda iron ore deposits have higher proportion of kaolinite in the finer fractions and are meant to be separated with cyclones. The iron processing flowsheet of Joda comprises of water only cyclone for beneficiation of iron ore fines. Water only cyclones are used for the beneficiation of fines in the iron ore processing industry and have a larger cone angle compared to that of conventional hydrocyclones to enhance the density effect in the separation. They are aimed to achieve better product quality of underflow however; the desired result could not be achieved at the Joda processing plant. The water only cyclones were operating at the corrected cut-size of about 60 micron with an imperfection of 0.40 and water split to underflow was approximately 10%. The overall Fe recovery from the water only cyclones were 60%. Since the quality of fines produced from the water only cyclone couldn’t be improved, an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality. The trial results indicated better product quality with the Fe recovery of 72% at corrected cut-size of 70 microns and imperfection of around 0.29. In view of above results it was recommended to replace the water only cyclones with hydrocyclones to achieve higher product quality of about 60% Fe content.INTRODUCTION Water only cyclones were installed at wet plant, Joda to process the classifier fines where the cyclone underflow is considered as concentrate and overflow is discarded as slime. Because of the lower capacity of the cyclones 30% of the classifier overflow was bypassed directly to thickener. Apart from this the quality of fines produced from the water only cyclone couldn’t be improved further hence an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality and quantity. Hydrocyclone was installed at Joda after replacing stub-cyclone and came into operation on 23rd Aug’ 2017.The process variables of water only cyclones and hydrocyclones are tabulated below:"

Jan 1, 2018

By Richter, E. Charikinya

"Mineral processing unit models require information on particulate properties such as particle size, solids flowrate and mineralogical composition to model their operations. Process models that describe the separation process can be classified based on the level of information required from the ore, i.e. the feed stream to the separating unit. The most comprehensive level of mineral processing models is the particle-based modelling approach. Particle based modelling describes a modelling approach where mineral composition, mineral liberation and textural information of particles making up the process streams is used in modelling. The advantage of this approach is that all model streams carry particle level information (size, liberation, shape). This information is obtained by applying automated mineralogy techniques such as Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN) analysis which provide accurate and detailed information on process stream particle properties. Currently the use of liberation information in modelling and simulation is rare, due to the limited number of separation models that liberation data as input. The objective of this study is to develop a particle based model for a dry magnetic separator, where mineralogical information is used directly to simulate a dry magnetic separator operation. Magnetic separation tests were carried out on high, medium and low grade magnetite ores using a laboratory magnetic separator. Streams from the separator were sampled and sized for chemical and liberation analyses. A sized mass and elemental balance around the magnetic separator was carried out. The elemental assays of each stream were converted to mineral quantities and a sized mineral balance was done. QEMSCAN measured liberation data was reconciled to the mineral balance based on mineral quantities obtained from chemical assays. This was followed by the development of a particle based model that calculates the trajectory of a single particle based on its mineral composition and textural properties. The model was tested on experimental data and was able to predict the effect of variation in process feed stream mineralogical attributes (liberation, grade, particle size) on magnetic separation performance. Results of this study highlight the benefits of the particle based modelling approach. INTRODUCTION The extraction of mineral values from ore requires liberation of the value minerals from the gangue followed by their separation. Liberation is achieved by size reduction operations (Desmond, 2008; Fuerstenau and Abouzeid, 2002). Separation of gangue material from value mineral takes place in various mineral upgrading stages such as classification, magnetic separation and flotation. In these concentration stages value minerals are separated from gangue minerals based on the physical properties of the ore particles making up the feed such as size, liberation, volume of magnetic material and density. The success of separation is related to the liberation of the feed particles, the performance of the separation technology applied, as well as the inherent characteristics of the feed material (Leißner et al., 2013)."

Jan 1, 2018

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

Due to the shortage of fresh water in the Middle East, seawater has been used as an alternative in flotation beneficiation. The flotation process requires about 7 m3 of water/mt ore. This article aims to study the effect of seawater cations and anions on the flotation. Natural pure francolite, calcite, dolomite and quartz were characterized by chemical, thermal and x-ray diffraction analyses, surface area, solubility and zeta potential. Synthetic seawater was prepared with the major chemical composition similar to natural seawater as follow; 2.45% NaCl, 0.52% MgCl2, 0.41% Na2SO4, 0.116% CaCl2 and 0.07% KCl. Also, natural seawater was used in application. The point zero of charge was estimated at pH 6.5, 7.8, 9.2 and 2.2 for francolite, calcite, dolomite and quartz, respectively. Calcium ions were released from the three minerals with Mg2+ and P2O5 3– released from dolomite and phosphate, respectively. The adsorption of collector, zeta-potential and floatability of pure minerals were studied. The effect of individual cations and anions predominant in seawater are studied on individual mineral or group. The troublesome Ca2+ and Mg2+ ions should be controlled by soda ash addition. Sodium silicate improved the selectivity of mineral mixtures and natural ore. At optimum conditions the calcareous phosphate ore yielded a concentrate of 34% P2O5, at 83% recovery with 0.61% MgO, from an ore assaying 25.3% P2O5 and 9.4% MgO. To minimize the Clcontent, fresh water of about 0.5 m3 /t was used and the Cl- decreased to about 0.09 %

Jan 1, 2003

By Mohan Ram

Structural impurities in the crystal lattice of rock phosphate of Indian origin is a great challenge for beneficiation and practically possesses remote scope of upgradation to the desired level for industrial utilization. There is a wide occurrence of rock phosphate in different parts of India with different characteristics viz. siliceous, carbonaceous and ferruginous. The structural cationic replacement in the composition of apatite is due to the exchangeable cations present in the external impurities associated with the rock phosphate ore. The Indian rock phosphate ore from Purulia district, West Bengal is characterized as unusual structural composition due to the exchangeable cation in its composition. The elemental distribution of ore exhibits the disproportionate ratio of P2O5 and CaO which is 5.88: 3.31 in reference to the theoretical composition of P2O5: CaO in apatite which is 4.23: 5.55. The substitution by trivalent Al+++ cations within the structure of apatite in place of divalent Ca++ is found upto 18% and substitution of exchangeable cation in place of PO4 and F ion by CO3/SO4 is found upto 0.1% and OH ions upto 0.2% respectively in a lattice of apatite thereby diluting the grade of rock phosphate and restricting its industrial use even after beneficiation. This paper reveals the unusual compositional features of rock phosphate under study and is a guideline to the mineral industries using such rock phosphate. Keywords: external impurities, exchangeable cation substitution, structural compositional features, electron probe micro analyzer

Sep 1, 2012

By N. Naudé

The theory on particles displacement subjected to upwards and settling movements in water, using a water pulse, is described in literature, but very little experimental data is available to verify these theoretical ideas. The aim of this research work was to visualize the displacement of solid particles in a mixture of water and solid particles created with the aid of water pulses in the Mineral Density Separator. From the literature it is known that lighter particles are subjected to higher levels of displacement than heavier particles, and when the particles then settled down, layers of material are formed ac-cording to the densities of the material. By removing the individual material layers, the materials can then be separated according to their densities. During this study the individual material layers were investigated regarding the density and size distribution in that specific density layer. It is important for this project to have a statistical prediction of the ?real? flow of the particles with different density and size distribution, inside the Mineral Density Separator. The information gathered during this study will be used to show the correlation between a two dimensional model of the particle flow and that of the real three dimensional flow inside the Mineral Density Separator.

Jan 1, 2014

By Sydney Mantsho, Toni Streczynski, Manuel Gonzalez

"In 2013, the commissioning of the MillStar Stabilisation and FloatStar Stabilisation and Optimisation controllers were completed at the Cerro Bayo Silver (Ag) mine in Patagonia, Chile. The MillStar control system has stabilised the feed to the SAG mill as well as the density at the discharge end of the SAG mill and ball mill. The FloatStar Stabilisation and Optimisation controllers have successfully stabilised and optimised the flotation circuit to ensure consistent product quality within desired specifications.The mill feed is controlled utilising the MillStar Solids Feed controller. Additionally, the solids to liquid ratio into the SAG mill was controlled utilising the Mill Inlet Ratio controller in conjunction with the Solids Feed controller. The discharge end of the milling process is a highly interactive and complex system. The use of a Robust Nonlinear Model Predicative Controller (RNMPC) was ideally suited to control this section of the process. On the Cerro Bayo milling circuit, the RNMPC was used to control the mill discharge sump level and the primary cyclone feed density to produce a more consistent feed to the flotation circuit.Three levels of the FloatStar control system were installed, for flotation stability, concentrate flow stability as well as grade optimisation. The Level Stabiliser was used to stabilise the level control on 6 flotation banks. The Flow Optimiser was commissioned on the Rougher, Scavenger and Cleaner concentrate sumps to stabilise concentrate flow from the flotation cells. The Grade Recovery Optimiser was commissioned on the Roughers section. A number of instrumentation challenges were identified which limited the overall benefit derived from the system. Once these were addressed, the performance was optimised. The overall benefit provided by the system was observed in terms of the improvements in Ag recovery."

Jan 1, 2014

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei and these ores require mineral processing to remove the substrate/nuclei rock before smelting. This paper reviews the results of jig separation and air table treatment for the coarse fraction and flotation and hybrid jigging for the fine fraction. Using these techniques substrate/nuclei rock was removed from the cobalt-rich ferromanganese oxide components. The mineralogical properties and metallurgical treatment methods including hydrometallurgical treatment of low grade ore is also reviewed.

Sep 1, 2012

By L. O. Filipov, N. E. Menad, A. Geneyton

"Zeta potential of synthetic monazites presenting various compositions were measured to investigate the effect of the main lanthanides substitutions on electrophoretic mobility and resulting IEP. The measurements are performed in a CO2 depleted and enriched solutions showing both reduced influence of monazite chemistry and strong influence of ions resulting from the solubilization and dissociation of CO2. The influence of oleic acid on the electrophoretic mobility of those monazites was also investigated. The influence of pH on oleate adsorption was studied using a bubble/particle adhesion system. Adhesion strength measurements were performed on pure synthetic monazite-(Ce) and monazite-(La). An extensive thermodynamic model of monazite in water was developed to highlight correlations between lanthanides hydroxides/carbonates species concentrations in the bulk solution and oleate adsorption. Based on electrophoretic measurements, advanced thermodynamic consideration and adhesion measurements, further details of the oleate adsorption model on monazite surface were proposed.INTRODUCTION Electrophoretic and potentiometric data on monazite and, a fortiori, other rare earth semi-soluble salts such as bastnaesite are extremely erratic (Chelgani et al. 2015). The isoelectric points measured with electrophoretic mobility methods range from 4.7 to 6.5 although sporadic data indicates an IEP (isoelectric point) far from that range. Different explanations are proposed in the literature to explain the IEP variability notably the numerous chemical substitutions that frequently occurred within monazite crystal lattice (Chelgani et al. 2015). Based on lanthanides speciation diagram, several authors highlighted the influence of specific lanthanide species on the flotation performance of rare earth semi-soluble salts when carboxylate or hydroxamate collectors are used. Although lanthanides ions have a great affinity for carbonates groups (Kragten et Decnop-Weever 1987), lanthanide (hydrogen) carbonates were not implemented in speciation diagrams. In this work, an advanced thermodynamic model is proposed to highlight correlation between flotation performance and lanthanide species predominance but also concentrations. Qualitative measurement of the monazite surface hydrophobicity are performed through tests of adhesion of coarse monazite particles onto bubbles. Since flotation and microflotation technics are highly influenced by hydrodynamic parameters, this method was investigated to obtain a sharp contrast between appropriate and inappropriate pH conditions. This paper is to investigate 1) the effect of lanthanides substitution on monazite surface properties through zeta potential measurements, 2) the mechanism of adsorption of carboxylates on monazite surfaces and 3) the effect of CO2 on monazite surface properties and carboxylates adsorption."

Jan 1, 2018

By G. Pahomova

"It developed an alternative to traditional flotation enrichment refractory of complex lead-zinc ores to obtain conditional lead and zinc products. The scheme involves the use of the processing method of gravitational enrichment of the primary cycle and the combined gravity-flotation-hydrometallurgical in finishing. The method has a high level of comprehensive utilization of mineral raw materials in relation to the elements that are extracted in the process of enrichment in lead concentrate, and the increase in recoverable value of processed ores. INTRODUCTION The primary source of lead are complex sulphide lead-zinc ore, lead ore actually rarer. The value of lead and zinc ores (except lead and zinc) is determined by the presence in them of a wide range of associated components: silver, contained mainly in galena; gold; bismuth in the form of its own minerals, but is associated with galena; cadmium contained mainly in the sphalerite; indium, thallium and gallium contained in sphalerite and galena; selenium and tellurium are present as impurities in the sulfide, tellurium is also found in the form of its own minerals. Of note harmful impurities antimony, which is often associated with lead sulphosalts and arsenic, having a substantially own minerals. By quality (content of lead, or the total content of lead and zinc) lead-zinc ores are divided into rich, ordinary and poor; by oxidation - to sulfide (with a lead oxides content less than 15% and zinc oxide content less than 10%), mixed and oxidized (50% oxide); the latter have a subordinate importance as a source of zinc and lead. Traditionally, the most contrasting technological properties of sulfide ores of nonferrous metals considered flotation properties, which determines the priority in the selection of flotation technology of their enrichment. Other methods of enrichment - gravity (jigging and enrichment in heavy suspensions), radiometric sorting (separation) are used as preliminary operations whose main purpose is to increase the content of lead and zinc in the ore sent to flotation, as well as the removing of part of empty rock in dumping tails prior to flotation. Effective implementation of these methods is possible at large size emphasizing in the ore of lead and zinc minerals, which is typical of the rich ores and which so far mainly worked. At the same time, non-ferrous metal ores (polymetallic, lead-zinc, copper-zinc, etc.) have a sufficiently high contrast to gravitational properties since ore minerals have a higher density compared with a rock minerals. But the gravity of the practice of non-ferrous ores enrichment is not widely used, despite its high degree of environmental safety and lower cost expensive."

Jan 1, 2018

By Teja Reddy, Narasimha Mangadoddy, Mandakini Padhi

"In mineral comminution circuits, the feed to hydrocyclone consists of a heterogeneous mixture having varied degrees of liberation and sizes leading to the multi-component particle system. The presence of multicomponent particles exhibits a significant change in the classification performance parameters. In this work, a numerical study is conducted with an artificial mixture of magnetite and silica of different proportions having similar particle size distribution to understand the multicomponent interaction in a laboratory scale hydrocyclone. The heterogeneous feed is injected tangentially would attain different settling rates under the influence of centrifugal, drag and turbulent dispersion forces. In this work, Large Eddy Simulation (LES) is used to resolve the continuous phase turbulence. Modified Algebraic Slip Mixture (ASM) model using the corrected Newtonian rheology of fines to simulate multi-density and multi-size particles of the mixture in a hydrocyclone. The influence of the multi-component particles on classification performance is extracted from the simulation in terms of the performance curve, i.e. recovery to underflow, volume fraction distribution and the key forces acting on each particle in the mixture. An interaction was observed between different components during the classification process, featuring accumulation of heavier particle at wall-side pushing the lighter particles into the inner locus of zero vertical velocity (LZVV) zone. The comparison of separation factors of different size particles presented the higher probability of the magnetite of same size reporting to wall region and hence to underflow. Hence, an increased component cut-size with the increased magnetite proportion, particularly a profound effect on lighter density component’s cut-size was observed. INTRODUCTION The multicomponent existence is found in naturally occurring ores, affecting the pure metal extraction, nonetheless also affects the comminution and classification processes. Among many another classifier, hydrocyclone is a vital equipment used vastly in many industries. The main advantages over other classifiers are a static body, low operating cost and maintenance, high throughput, low floor space requirement etc. A typical hydrocyclone consists of a cylindrical section with a central tube connected to a conical section with a discharge tube. The fluid is injected tangentially into hydrocyclone causes swirling and thus generates centrifugal force within the device. The multiphase interaction inside the hydrocyclone is extremely complex and mostly explained by theories based on hypothesis. In past years, many theoretical models were proposed like a balanced orbital model (Criner, 1950), the residence time model (Reitema, 1961) etc. Though these models give an estimation of the cut-size and other performance parameters, it cannot predict the accurate performance of the actual state of operation. Among these models, the balanced orbital theory is the most adapted concept, based on the force balances of the particle in the dual vortex flow of hydrocyclone. The finer particle is subjected to the inward drag force, generated from the outer vortex flow to the air core, and drags the particle towards the overflow. The larger particle with the higher mass have enhanced centrifugal force and falls into primary vortex near wall reporting to the underflow. Generally, the forces acting on the particle include the drag force, centrifugal force, pressure gradient force, added mass force, Saffman lift force, Magnus force and basset force (Kraipech, 2005). The major forces like a drag, centrifugal, pressure gradient are the function of the particle properties like the size and the density. Hence, the existence of the multi-size and the multi-density particle will affect the separation phenomenon, with the varied forces acting on it. The understanding of the multicomponent classification effect using ores has been only explored in few studi"

Jan 1, 2018

By Jacques Eksteen, Sharif Jahanshahi, Neill J. Bartie, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgO-SiO2-Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. This effect is shown in Figure 1 for the six slag compositions investigated.

Jan 1, 2003

By Alexey P. Tatarinov

Under modern economic conditions in Russia, gold heap leaching is the most effective way of investing into gold-mining industry. Gold is recoverable from small-size deposits, low-grade ores from oxidation zone, cut-off grades, and overburden rocks using heap leaching. This technology is cost-effective and allows a saleable metal to be obtained within the first year of operation. The investments for heap leaching are lower than those of for a traditional plant technology. Production cost per one gram of Au is 5-7 times lower than that of during a plant flow sheet. A seasonal development of mines can be possible. With reference to this, heap leaching resembles the technology of placer deposits development. One of the major advantages of heap leaching is the form of the product. Gold can be obtained as dissolved in a clarified PLS, which allows the further quick treatment. The amenability of ores to heap leaching depends on their mineralogical composition. Oxidized porous ores with a good access of a lixiviant to valuable particles can be treated without pre-crushing. Clayish minerals are often found in oxidized ores with free gold. In order to build ground for heap, several major methods combined with various pad materials are used. These methods have been used at many plants and are reliable. The development of heap leaching technology for gold ores for the deposits from Yakutia, Zabaikalsky region, Primorye region, Uzbekistan, Tadjikistan, and Kazakhstan began in the 70s. However, it has been commercially used only since 1990. The first heap leach plants were built and commissioned in the USSR in 1991 at Vassilkovsloye deposit (Kazakhstan) and at Maiskoye deposit in Russia in 1994. Pilot plant testing was conducted in 1996 using ores from Kuranakh ore field, deposits Phiskulturnaya-Kholodnaya and Lopukhovskoye from the Aldan region. After the first successful commissioning of heap leaching plant in Russia, this technology has been commercially applied for deposits. Every year 1-2 heap-leaching plants were commissioned. More than 30 heap-leaching plants have been commissioned both in Russia and in the former Soviet Union using technologies developed by IRGIREDMET. Keywords: cyanide leaching, heap leaching, ore, percolation, solutions, lime technology

Sep 1, 2012

By Yury V. Kulikov, Rakan Rahbani, Arkady Y. Senchenko

"The relevancy of complex minerals treatment is constantly increasing taking into account mineral resources depletion. Different refractory ores and concentrates, oxidized and polymetallic ores, as well as metallurgical products (slags) can be assigned to such mineral type. The treatment of such products via conventional flowsheets requires considerable capital and operational costs and does not always provide high recovery level of valuable components into a saleable product. Therefore, considerable amount of ores and metallurgical products are not treated, or treated inefficiently. One of the most promising approaches that allows economic treatment of refractory products is their ultrafine grinding down to 5-20 µm with subsequent processing or hydrometallurgy. Horizontal bead mills - the IsaMillTM, developed by Xstrata Technology, received their wide application in mining industry. Standard testing is performed under laboratory conditions in an M4 IsaMillTM (volume - 4 liters) to define the parameters of fine grinding. This mill completely simulates the operation of full scale industrial mills up to 50 m3 in volume (up to 8000 kW motor). The paper describes fine grinding technology performed in bead mills, and the importance of testing according to a certified method for industrial equipment selection. The paper contains description of promising directions of fine grinding technology application for several projects in Russia and Kazakhstan."

Jan 1, 2014

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Autogenous (AG) and semi-autogenous (SAG) mills often operate in an unstable state because of the difficulty to balance the rate of replenishment of large ore particles from the feed with the consumption in the charge. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behaviour of the mill charge. A problem in attempting to measure those parameters is getting a sensor that is both robust and sensitive enough for continuous on-line measurement.Techniques that measure the force acting on the lifter when it hits the charge inside the mill have got an increased interest recently because of the ability to combine it with DEM modeling. This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a 2D DEM modelling technique is used with Metso HFS software.The pilot mill is a grate-discharge mill, equipped with 12 rubber lifters of square size 0.1 m, face angle 45 degrees. Steel balls in the size range 10-30 mm and density 8000 kg/m3, are used in the experiments. Test material is a hematite pellet feed, d50 around 45um, chosen to get stable grinding conditions with respect to feed size variations.The experiment is meant as a first test of the equipment’s performance, and to study how the sensors respond to changes in some operating variables. To get an understanding of, and distinguish between correlation and causality, experiments are performed according to a full factorial design with two levels, and in addition two replicates of the experiments at a center-point in the charge level setting."

Jan 1, 2003

By Güven Önal, Zeki Dogan, Neset Acarkan

In this study, it was aimed to produce glass sand with less than 0.15% Fe2O3 for window glass manufacture and glass ware grade with less than 0.05% Fe2O3 from Yalõköy sand dunes having 0.48% Fe2O3. In order to reduce the iron content of the Yalõköy sand dune, magnetic separation, flotation, scrubbing, H2SO4 leaching and drying were used. The optimum iron removal was achieved by H2SO4 baking at 150oC and 8 kg/t acid consumption. In this way, sand concentrate was obtained with 0.04% Fe2O3 and sand recovery 95%.

Jan 1, 2003

By S. K. Kawatra, T. C. Eisele

"Coal-fired electrical power generation plants produce 56% of all the electricity in the U. S., burning approximately 860 million tons of coal annually. This results in production of 58 million tons of fly ash; 19 million tons of bottom ash and boiler slag, and 23 million tons of desulfurization sludges. These are a considerable disposal problem, and it would therefore be very valuable to be able to sell these residues and byproducts as useful materials, rather than paying to dispose of them in landfills. However, utilization rates are currently very low, below 32% even for the most thoroughly commercialized combustion byproduct (fly-ash). This poor utilization rate is a result of the high impurity content of combustion byproducts, which make them unsuitable for existing markets. The experiments described in this paper were therefore carried out to study the application of mineral processing techniques to upgrading combustion byproducts.Experiments were conducted to upgrade and purify low-grade combustion products to produce highgrade, readily saleable materials. A process was developed for removing unburned carbon from coal fly-ash by froth flotation, using reagents originally developed for flotation of oxidized coals. This technique could reduce the carbon content of fly-ashes containing up to 11.1% carbon to less than 2%. The froth product was sufficiently carbon-rich that the recovered carbon has value as fuel, or as low-grade activated charcoal.Fly ash was also examined as a binder for producing iron ore pellets, primarily as a substitute for bentonite. It was found that Class F fly ash in combination with an activator (calcium hydroxide) was an effective pellet binder at dosages comparable to the currently-used dosages of bentonite clay. While the flyash worked very well alone, tests in combination with bentonite showed that fly-ash/bentonite mixtures had significantly worse binding performance than either pure bentonite or pure fly-ash-based binder. This was determined to be due to the fact that bentonite and fly ash have profoundly different binding mechanisms, with fly-ash undergoing a pozzolanic chemical reaction while bentonite binds through a physical attachment process."

Jan 1, 2003

By Lei Pan, Roe-Hoan Yoon

"Direct force measurement for bubble-particle interaction has been difficult due to bubble deformation, which makes it difficult to know the separation distances between the two macroscopic surfaces. In the present work, we have developed a method of monitoring the deformation accurately, while directly measuring the interaction forces. In effect, we can ‘see’ bubbles interacting with mineral surfaces under different hydrodynamic and chemical conditions and determine both the hydrodynamic and surface forces involved. In the present work, a high-speed camera has been used to record the optical interference fringes of a thin liquid film (TLF) of water formed on a mineral surface. The recorded fringes are then used to reconstruct the spatiotemporal profiles, from which one can determine the hydrodynamic pressure using the Reynolds lubrications theory. From the forces directly measured in the present work and the hydrodynamic pressures obtained from the fringes, we have determined the disjoining pressure. The results show that air bubbles interacting with hydrophilic surfaces form stable TLFs with zero contact angles. The TLF formed on a hydrophobic surface thins fast, form a ‘pimpled’ film, and ruptures to form a finite contact angle. The new information obtained in the present work may be useful to better understand the role of hydrodynamic and surface forces affecting bubble-particle interactions."

Jan 1, 2014

By Yong Liu, Peng Qian, Shu-Feng Ye, Shao-Jun Chu, Pei-Wei Han

"Chromite with a low mass ratio of Cr to Fe (Cr/Fe ratio) was treated by the carbochlorination method using solid chlorinating agent (MgCl2 and CaCl2) and carbon in the present paper. The results showed that iron could be selective removed mainly in the form of FeCl2. The removal of iron was indirectly, which consisted of the decomposition of solid chlorinating agent to release Cl2/HCl and the carbochlorination of FeO•Cr2O3 by Cl2/HCl and C. The Cr/Fe ratio increased as increasing temperature from 700 ? to 900 ? in air atmosphere, while the tendency was opposite in N2 atmosphere. The removal efficiency of iron by CaCl2 was better than that by MgCl2. At last, a new pelletizing process was proposed to treat fine chromite with a low Cr/Fe ratio based on carbochlorination method, which could produce the high quality roasted chromite pellets with higher Cr/Fe ratio and compressive strength. INTRODUCTION Chromite is mainly used for the production of ferrochromium. A high Cr/Fe ratio (>2) of chromite is usually required to meet the technical specification of ferrochromium.(Gasik, 2013) Attentions have been attracted to the economic and efficient methods for the recovery of chromium from lower-grade ores as the higher-grade ores become depleted. However, the Cr/Fe ratio is difficult to improve through the conventional beneficiation methods (such as gravity concentration, flotation) due to the spinel composition, although beneficiation methods could increase the metal content of chromite ores by removing gangues.(Nafziger, 1982) The main industrial mineral of chromite is (Fe,Mg)O•(Cr,Al,Fe)2O3, which belongs to spinel magnetite.(Liu, 2013) Iron should be selectively removed through the structural dissociation of spinel to increase Cr/Fe ratio.(Nafziger, 1982)"

Jan 1, 2018

By Georgios N. Anastassakis

"The depletion of the high-grade chromite ores and the inefficiency of the gravimetric methods to process fine particles has shifted the industrial and research interest from gravimetric separation methods to flotation. However, the response of the minerals to various flotation schemes is not clearly established. In this work, the physicochemical behavior of chromite and olivine is studied using a fatty acid collector.The minerals used were from Vourino area (Kozani, Northern Greece). Macroscopically pure samples of chromite and olivine were selected by hand picking, crushed and subsequently ground to the required size. Each sample was then submitted to panning and magnetic separation for the removal of impurities. The mineralogical and chemical analysis of the purified samples revealed the following: a) The purity of chromite was 95% while the minor constituent was mainly magnetite. Its chemical analysis was: 12.50% Fetot, 2.50% SiO2, 54,54% Cr2O3, 9.31% Al2O3, 0.47% CaO, 13.10% MgO. These analyses show that Cr3+ has been substituted by Fe3+ and Al3+ as well as Fe2+ has been significantly substituted by Mg2+. b) Forsterite is the main constituent of olivine either as pure forsterite (Mg2SiO4), which is the prevailing form, or as iron-forsterite [(Mg,Fe)2SiO4] in less amount. Chrysotile, which belongs to the serpentine group, was also detected at a percentage of 10-15%. The chemical analysis of olivine was: 36.90% SiO2, 0,53% Cr2O3, 7,43% Fe2O3, 0.72% Al2O3, 0.91% CaO, 47.00% MgO, 6.02% LOI.The electrokinetic behavior of the minerals was studied in a electrophoretic mass transport equipment Model 1202 of Micromeritics. The reagents used were sodium hexa-metaphosphate of commercial grade and sodium oleate."

Jan 1, 2003

By Song Z. Guo

Calcite and magnesite are both carbonate minerals and their crystals belong to trigonal system. Flotation tests were carried out to investigate the flotation behaviors of calcite and magnesite. The test results show that the floatability of calcite and magnesite under different grinding environment had obvious differences. The floatability of calcite using sodium oleate as collector after dry grinding is better than wet grinding, but the floatability of magnesite after wet grinding is better than dry grinding. The XPS surface elements test and zeta potential measurement show that, wet and dry grinding process makes the distribution difference of surface anion and metal cation, then influence the floatability of the two carbonate minerals using sodium oleate as collector. Difference of the carbonate crystal structure and solubility properties was also investigated. Research shows that crystal structure difference of calcite and magnesite causes the difference of solubility, which can influence the flotation behaviors under different grinding environment. Keywords: carbonate mineral, crystal structure, solubility properties, flotation, surface character

Sep 1, 2012