Search Documents

By Charles H. Dowding

Whenever piling vibrations are significant, construction activities associated with pile driving and/or excavation can produce permanent displacement. These permanent displacements are more detrimental to structural performance than the hair sized, cosmetic, plaster cracks that might be produced by slightly exceeding reasonable vibration controls. Case studies are presented which demonstrate the relative importance of permanent displacements compared to directly produced transient vibration displacement within a horizontal distance of one pile length. Special attention is paid to settlements produced by densification of liquefiable sands. SOURCES OF TRANSIENT AND PERMANENT DEFORMATION DURING CONSTRUCTION Confusion over multiple sources of facility deformation caused by adjacent construction complicates the discussion of the relative importance of vibration induced cracking. None of the recent scientific investigations of vibration induced cracking (Siskind et el, 1980), involved deformation other than that produced by ground vibration from rock blasting. Thus these studies carry the implicit assumption that no ground deformation occurred other than that produced by the transient vibration. In other words there is no permanent deformation other than that which is typical of the older residential structures investigated.

Jan 1, 1991

By Allen B. Stanton, Parthiv Brahmbhatt, Michael Grimm, Stanley L. Worst

Constructing a circular shaft consisting of secant piles has its own complications which make it more difficult than typical drilled shaft construction. Add to that performing under low overhead powerlines and sitting inside of a 40-foot deep, 50-foot diameter shaft and it becomes more about logistics than the actual drilling. The complexities associated with the Romeo Arm Interceptor Segment 5 Lining project are the focus of this paper, delving into the details that made it work successfully.

Oct 1, 2022

By Tatsunori Matsumoto

In order to investigate the variation of the load-displacement relations of piles in a site, vertical load tests were carried out on 25 small diameter steel pipe piles. Out of 25 piles, 15 piles were close-ended pipe piles attached with a blade at the pile toe and 10 piles were open-ended pipe piles. To carry out these load tests in a short period, two types of rapid load test methods, Spring hammer load test and Falling mass load test, were employed. The load tests of all piles were completed in two days with 180 blows in total. In order to estimate a static load-displacement of a pile, non-linear damping method was used. It is shown from the test results that the performance of the pipe piles such as the ultimate pile resistance and the initial pile head stiffness is improved by re-driving.

Jan 1, 2006

By Arash Khosravifar, Nason McCullough, Stephen, Milad Souri, Scott Schlechter, E. Dickenson

The results of five centrifuge models were used to evaluate the response of pile-supported wharves subjected to inertial and liquefaction-induced lateral spreading loads. The centrifuge models contained pile groups that were embedded in rockfill dikes over layers of loose to dense sand and were shaken by a series of ground motions. The p-y curves were back-calculated for both dynamic and static loading from centrifuge data and were compared against commonly used API p-y relationships. It was found that a significant reduction in ultimate soil resistance occurred in dynamic p-y curves in partially/fully liquefied soils as compared to static p-y curves. It was also found that incorporating p-multipliers that are proportional to the pore water pressure ratio in granular materials is adequate for estimating pile demands in pseudo static analysis. 1. INTRODUCTION Liquefaction-induced ground deformations can cause severe damage to pile-supported wharves and other waterfront structures. A common approach in analyzing the lateral behavior of piles against seismic loads is using the beam on nonlinear Winkler foundation (BNWF) or p-y spring analysis. One common p-y relationship for sand is the one proposed by the American Petroleum Institute, also known as the API sand model (API 1993). While the API sand model was originally developed for the static loading conditions, it is common to modify the API sand curves for the effects of cyclic loading. However, there is no consensus on how to modify the static p-y curves for the effects of liquefaction and pore water pressure generation in loose granular soils. In previous studies, p-y springs of piles in liquefying soils were back-calculated from case histories, centrifuge model studies (e.g., Wilson et al. 2000; Brandenberg et al. 2005; Abdoun et al. 2003), full-scale tests (e.g., Rollins et al. 2005; Chang and Hutchinson 2013), and numerical analyses (e.g., McGann et al. 2011). In general, these studies found the softening effects of soil liquefaction on p-y curves, as well as a hardening behavior attributed to the dilative response of the liquefied soil around the pile. However, these studies provide varying recommendations on how to modify the static p-y curves to capture this complex behavior. Some design guidelines propose softening the static p-y curves using p-multipliers (e.g., Caltrans 2012). Other studies propose an upward concave shape for p-y curves in liquefied soils (e.g., Franke and Rollins 2013; Chang and Hutchinson 2013).

Jan 1, 2019

By J. M. Pei

In this paper, the nonlinear finite element analysis is used to study the support system of a tunnel which is designed to pass through deep-embeded stratum. The rock mass is rather intact, though a section of tunnel will pass through the weak belt. Under the influence of the high ground stress, the condition of stability and the form of support become complicate. This paper, talcing into account the nonlinear properties of rock mass and the Interaction between rock, and support, makes a comparison between the two kinds of soft and rigid support systems, and analysed the changes of their bearing forces.

Jan 1, 2010

By Kozo Takeda, Arashi Shimano

"Dry Jet Mixing (DJM) method as the representative deep mixing technique has been demonstrating best practice on ground mitigation works coping with complicated soil condition and limited site space. This technique plays an important role in many projects to stabilize soft ground involving troubles like sliding failure, settlement, bearing capacity etc. Serious disasters caused larger earthquakes make great demand on the application of deep soil mixing these days. Special design and alignment of deep soil mixing has been established against to liquefaction and serious failure due to liquefaction. In this paper, representative example of liquefaction mitigation by DJM method is summarized. The paper also present result of surveillance of sites installed DJM col umns after attack by Tohoku Pacific Ocean Earthquake. Performance of DJM columns suffered the earthquake is demonstrated at several sites even with conventional column alignment.INTRODUCTIONThe DJM method is a representative deep soil mixing technique of dry mixing manner in Japan. DJM can successfully install soil mixing columns trough automatically controlled binder injection based on pneumatic feeding theory and cumulative experiences.This method was joint-developed in 1978 by private organization under initiative of the Public Works Research Institute of the Ministry of Construction as the optimum method for improving the Japanese soft ground. Figure 1 shows full view of the DJM construction system. Figure 2 illustrates DJM working system indicating Binder Feeding Plant side and Mixing Machine side respectively.As typical soil mitigation method, many projects related with rivers and roads and city development has required DJM technology. The total number of the projects applying DJM has exceeded 5,000 with the total treated soil volume more than 32,000,000 m3 by the end of fiscal year 2013."

Jan 1, 2015

By Shamsher Prakash

Equivalent spring constants for analysis of footings is a function of Young's modulus of pile material (Ep), shear modulus of soil (Gs), and geometry of the footing and/or piles. Shear modulus is strongly strain dependent in soils. Therefore, the spring constants are strain dependent, which is acceptable to the Geotechnical engineers. However, structural engineers prefer to use spring constants as a function of displacement, rather than strain. In order to develop these relationships, appropriate relationships between strain and displacement are needed. Also, modulus degradation with strain needs be built into these relationships. Description of spring constants kx , ky, and kz in x, y, and z direction and k?, k?, k?, about x, y, and z directions are relatively simple. However, description of kxø and ky?, the cross-coupling spring constants depend on 2 - components of displacement and rotation. Thus, there are 8 spring constants and likewise there are 8 damping constants. Approximate strain-displacement relationships on which displacement dependant k's and c's are based are presented with appropriate equations, and a numerical example is included illustrating k's and c's as functions of displacement.

Jan 1, 2002

By Takefumi Takuma, Hiroyuki Nishimura, Shigeru Kambe

"Japan’s Great Tohoku Earthquake and the immediately following tsunami of March 11, 2011 killed more than fifteen thousand people and destroyed numerous buildings and infrastructures in the northeastern part of the country.In addition to reconstruction projects in the areas where the earthquake and tsunami hit, other seismically vulnerable regions in the country have started building new and more robust facilities as well as upgrading existing coastal structures so they will be able to cope with such deadly seismic and hydraulic force. This paper will highlight two different types of aseismic and anti-tsunami levee upgrades currently under construction on the coast of Kochi Prefecture, approximately 500 miles west of Tokyo. The first type is the installation of double sheet pile walls in existing seawalls. The second type is to drive tubular piles into existing levee structures for reinforcing them. Both sheet and tubular piles are being driven by the Press-in Piling Method without removing or compromising the function of the existing structures. 1. BACKGROUNDGreat Tohoku Earthquake of March 11, 2011 caused severe damage to many structures. ASCE’s survey of damaged coastal structures conducted immediately after the disaster by Ewing, et al. (2014) categorizes failure modes of the structures in the following manner.?Overtopping without structural failure.?Overtopping with structural damage or failure.?Wave uplift forces.?Movement of structure off foundation from sliding, rotation, or overtopping.?Impact loads.?Hydrostatic pressure.?Supercritical flows.?Scour.?Erosion.?Abutments end effects.?Subsidence."

Jan 1, 2017

By Lucie Spencer, Craig Butterworth

"This paper presents the design of a raft enhanced pile group recently constructed for a hotel development in Perth, WA. At the time of construction in 2016 the hotel was the tallest prefabricated hotel in Australia.The structure covers the entire 12 m by 32 m development footprint, located in an inner city environment, and directly surrounded by existing structures. The small site and lack of space required innovative thinking in terms of the substructure design.The ground conditions comprise a layer of medium dense sand underlain by variable layers of stiff clay, silts and sands. Groundwater was around 1.5 m below ground level.The substructure design was carried out on the basis of a raft enhanced pile group. This allowed the use of much shorter piles than a conventional pile solution, thereby permitting the adoption of CFA piling techniques. This also allowed the raft thickness to be reduced to such that the substructure works were maintained above the groundwater level.The design was carried out in general accordance with the Australian Standard AS 2159 and using conventional piled raft design techniques involving iteration between elastic soil settlement software and structural analysis software until spring reactions were obtained with convergence of the two models. Following this springs were introduced to model piles in the structure.Due to the variable nature of the ground and resulting uncertainty in pile base capacity it was not considered appropriate to design the system as a pile assisted raft with piles loaded beyond their ultimate geotechnical design strength. As a result, all piles were designed based on a maximum load maintained within the elastic response region, with the majority of the load taken by the piles. However, the combined capacity of the raft and the piles allowed for a saving in pile lengths and numbers of around 40%, when compared to a conventional pile group designed in accordance with the Australian Standard AS 2159.The raft slab was monitored during construction in order to check the actual displacements against the design displacements. At the end of construction, the settlements were found to be within 2 mm of the design values.INTRODUCTIONThe Wellington Street area of Perth in the CBD is undergoing recent regeneration which includes the King’s Square development, Perth Arena and the Wellington Street Bus Station. The proposed hotel development is close to the recent developments on a Lot previously occupied by a low rise development. Due to the small size and constrained nature of the site, the substructure design for the tower needed to take into account available space and the impact of the works on adjacent properties. This paper presents reasoning for the choice of substructure design, details of the design methodology adopted, results from limited post construction monitoring and potential improvements that could be considered for similar future developments."

Jan 1, 1900

By Dena Morgan, Emre Biringen

"Abstract This paper discusses the execution of pile installation and design issues at two environmentally challenging industrial sites in North America. Environmental regulations set constraints on the design and require versatility in choice of technology.For a proposed bridge, due to protected fish habitat, performing soil borings within 30 m of the creek embankment was prohibited. The limited subsurface profile indicated a thick upper layer of granular material, thus driving H-piles was considered. However, to limit generation of vibration and noise in the protected area, drilled piles had to be used. During execution, the subsurface profile differed from that in the borings 30 m away. Very soft, saturated silt was encountered at the bottom of the caisson and the length had to be redesigned very quickly while the contractor waited for instruction. For a new structure in uncontrolled fill area, performing soil borings was not allowed. It was known that a layer of peat was present in the area, but no information regarding the thickness and extent. The subsurface profile generally consisted of granular material overlying a thick compressible silt layer. Somewhere within the granular layer peat would likely be encountered. Franki piles were chosen to penetrate the peat and bear in the underlying granular material. During environmental sampling in the area, methane gas was encountered and Franki piles were no longer a viable option due to safety concerns. The foundation system was changed to steel H-piles driven to bedrock, which was more than 50 m below the ground surface and sloping. Rock shoes that would work to significant slopes had to be used in order to increase the likelihood of good embedment within the bedrock. Also, due to obstruction of an approximately 3 m thick debris field that was encountered in the upper granular soils, some of the piles had to be relocated and extra piling needed to compensate for such differences. The results of PDA testing to estimate compressive capacity and a series of lateral load tests are presented.INTRODUCTIONThe design issues that are encountered during construction can be quite problematic and have a significant impact on schedule. In order to avoid such impact on the project, a thorough subsurface investigation should be considered prior to design and construction. Better understanding of environmental regulations also prevents costly changes to the foundation design. This paper discusses the execution of pile installation and the design issues at two environmentally challenging sites in North America.BRIDGEDuring the subsurface investigation for a proposed industrial building complex, several boreholes were drilled within the footprint or in close proximity of various structures, with Standard Penetration (SPT) sampling of the upper coarse-grained soils (sand/gravel) and undisturbed sampling of the lower fine-grained soils (silt/clay). The SPT blow counts (N60) were corrected by a factor of 1.35 in order to incorporate the SPT automatic energy transfer ratio. When Modified California Sampler was used, a correction factor of 0.44 to 0.64 was also applied. N60 values were further corrected for gravel to avoid artificially high blow counts during the analyses due to spoon samples contact with gravel and cobbles, and the corrected values of (NG)60 (limited to a maximum value of 50 blows/300 mm) were used for design. The information from the SPT boreholes was then used to assess the subsurface conditions beneath the structures, as well as for a nearby bridge that was designed to cross over a creek. Since performing soil borings within 30 m of the creek embankment was prohibited due to the protected fish habitat, the investigation with regard to the bridge abutments was limited to two deep boreholes (B10-33 and B10-34) at the bridge location and two additional boreholes (B10-35 and B10- 36) located approximately 200 m upstream. The bridge location and two sets of boreholes are"

Jan 1, 2014

"After the non-destructive testing is completed, the data must be compiled, evaluated, and interpreted. During this process, the data may indicate that there is an anomaly warranting further investigation, which may eventually be determined to be a flaw or defect. The definitions of an anomaly, flaw, and defect can be described as follows (after Amir, 2002):Anomaly - Any irregular feature identified in the NDT graphic results. An anomaly may be due to the testing instrumentation (such as noise), to the means used to perform the test (e.g. access tube debonding in CSL) or to the shaft itself. It is the responsibility of the NDT practitioner to gather and analyze all relevant data and try to resolve every anomaly before it is declared a flaw or defect.Flaw - Any deviation from the planned shape, size and/or material of the shaft.Defect - A flaw that, because of either size or location, may detract from the shaft’s intended performance or durability. The geotechnical engineer and the structural engineer are jointly responsible to decide which flaw comprises a defect.This section describes the process of evaluating the data, determining if an anomaly exists, and if so, deciding whether the anomaly is actually a flaw or a defect. If the anomaly is determined to be a defect, its effect on the performance of the shaft must be evaluated, and if necessary, the can be re-engineered, repaired, or replaced."

Jan 1, 2004

By Juan J. Campo

The Freeport-McMoRan Main Pass Mine development in the Gulf of Mexico is a complex designed to extract up to 67 million long tons of sulphur over a 40 year period. The initial development includes 15 platforms and 13 bridges located in water depths ranging from 208 to 214 feet, approximately 15 miles east of the Mississippi River Delta. Three additional platforms were designed and installed for the oil and gas development in the complex. Over 110, 000 short tons of steel were required to fabricate the structures. As the sulphur is extracted significant subsidence is predicted over a major portion of complex in the shape of a very large bowl. Vertical elevations are predicted to change as much as 65 feet. Horizontal movements and mudline slope changes cause adjacent platform decks to move as much as 30 feet relative to each other. Differential soil movement is predicted between piling of individual platforms causing the piling to spread, resulting in significant lateral loading on the piling. Relative vertical soil movements are predicted along the lengths of the piles which causes "up drag" or "down drag" forces on individual piles. This paper addresses the design of the piling for the structures in the complex. Design criteria will be discussed explaining how the more traditional offshore environmental and gravity loadings were combined with the unique loading caused by subsidence. Design and analysis procedures will be explained and analysis results presented. These results include the incorporation of 100 ksi steel in thicknesses up to 5 inches in some of the tubular piles. Comparisons will be made between conventional offshore structures and these structures designed to accommodate the subsidence.

Jan 1, 1992

By O&apos, M. W. Neill

Mini-piles have been found to be a practical, technically correct remedial underpinning method. They can be constructed in limited access areas with very little disruption. Experience indicated that mini-piles installed using a down-the-hole soil displacement hammer would be particularly effective in the "bottomless" Beaumont Clay formations in the Houston, Texas, U.S.A. area. The University of Houston Foundation Testing Facility was ideally suited to perform tests on mini-piles. The availability of extensive geotechnical data and previous pile test results was invaluable in evaluating the mini-pile test data. As expected, the mini-pile test results were consistant with test results from large sized driven piles in the same soil formation.

Jan 1, 1989

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By Martin Pratt

This paper is an overview of deep foundation engineering in Hong Kong past, present and future. The enormity of the subject compared with the space available makes brevity inevitable. Issues of construction and design are covered and some examples of recent challenging projects are given. The content is aimed at those with an interest in foundations generally, but with limited knowledge of the Hong Kong scene. Reference is made to informative publications for further reading on specific topics.

Jan 1, 2000

By Drew M. Kurtz, Jeff L. Rai, Sara F. Frailey, Mohammad Ayub Iqbal

"This paper presents the foundation changes made for a five-span bridge over the Lehigh River constructed as a design-build project. During excavation within the cofferdam at Pier 2 for the construction of a spread footing to bear on rock, it proved extremely difficult to control the water entering the excavation as the sheet pile tips were variable due to the bedrock pinnacles and a weathered rock zone above the top of rock allowing water to pass below the sheeting. Water also entered from the bottom of the excavation, possibly due to the presence of solution openings within the dolomite bedrock. After repeated failures to achieve subgrade elevation and maintain a dry excavation, a design change to drilled shafts was made. Additional borings were performed for each of the shaft locations to explore the area underlain by karstic dolomite rock. A seal consisting of tremie concrete with adequate weight was placed to counter the differential head of water and the three drilled shafts (with minimum 25 feet [7.62 meter] rock sockets) were installed. A detailed construction sequence was followed and advanced quality control testing was performed. The construction of Pier 2 was completed successfully.1. INTRODUCTIONThis paper presents the description of the design change made from spread footing to drilled shafts as a result of site conditions encountered during the excavation for the spread footing for a bridge pier in the Lehigh River in Allentown, Pennsylvania. The bridge is located in an area underlain with dolomite rock, presenting karstic conditions including irregular top of rock and solution openings that provided high hydraulic conductivity below the top of rock. Also, the presence of a zone of weathered rock and pinnacle rock prevented the advancement of sheet piles when constructing the cofferdam. Thus, the difficulties of advancing the excavation to the desired spread footing level resulted in the design change to drilled shafts during construction. Since the project was Design-Build, the design could be changed by a collaborative process through the efforts of the Contractor, its geotechnical and structural engineers, and the State's (owner's) geotechnical and structural engineers and construction management staff."

Jan 1, 2016

By Donald R. Clark

"Drilled shafts are being used as foundation support for parabolic solar troughs at the Genesis Solar Project being constructed near Blythe, California. Three types of drilled shaft foundations are required for the project. At project build-out, there will be a total of 23,008 drilled shafts installed at the site. Preliminary designs for the axial and lateral capacity of the drilled piers were based on conventional geotechnical engineering methodologies and soil-structure interaction. The drilled shafts and subsurface conditions were modeled through the use of the computer program LPILE v6.0.Conducting lateral load testing of drilled shafts was considered appropriate to confirm or modify the geotechnical parameters used in the preliminary design. The lateral load testing program was conducted to provide site-specific test data that would allow the design engineers (both geotechnical and structural) to predict the actual performance and adequacy of the proposed drilled shaft foundations and improve the efficiency and hopefully reduce project costs.The lateral load testing was conducted within two solar fields at the site. Three pairs of drilled shaft foundations were installed in each field, instrumented, and laterally loaded to determine load-deflection response. A value-engineered option, proposed by one of the drilled shaft contractors, was also load tested. The results of the load-deflection data obtained in the field was used to modify the soil modeling used in the original L-PILE analyses and adjust the production drilled shaft lengths.Based on the results of the lateral load testing, the in-situ moduli of the subsurface soils were significantly increased over that assumed in the preliminary analyses. Based on the final soil-structure interaction analyses, the preliminary drilled shaft lengths were reduced by 2 to 2-1/2 feet. This resulted in an overall reduction of 55,654 feet of drilled shaft construction on the entire project, a savings of approximately 16.5% over the preliminary"

Jan 1, 2017

By Donald R. Clark

Drilled shafts are being used as foundation support for parabolic solar troughs at the Genesis Solar Project being constructed near Blythe, California. Three types of drilled shaft foundations are required for the project. At project build-out, there will be a total of 23,008 drilled shafts installed at the site. Preliminary designs for the axial and lateral capacity of the drilled piers were based on conventional geotechnical engineering methodologies and soil-structure interaction. The drilled shafts and subsurface conditions were modeled through the use of the computer program LPILE v6.0. Conducting lateral load testing of drilled shafts was considered appropriate to confirm or modify the geotechnical parameters used in the preliminary design. The lateral load testing program was conducted to provide site-specific test data that would allow the design engineers (both geotechnical and structural) to predict the actual performance and adequacy of the proposed drilled shaft foundations and improve the efficiency and hopefully reduce project costs. The lateral load testing was conducted within two solar fields at the site. Three pairs of drilled shaft foundations were installed in each field, instrumented, and laterally loaded to determine load-deflection response. A value-engineered option, proposed by one of the drilled shaft contractors, was also load tested. The results of the load-deflection data obtained in the field was used to modify the soil modeling used in the original L-PILE analyses and adjust the production drilled shaft lengths. Based on the results of the lateral load testing, the in-situ moduli of the subsurface soils were significantly increased over that assumed in the preliminary analyses. Based on the final soil-structure interaction analyses, the preliminary drilled shaft lengths were reduced by 2 to 2-1/2 feet. This resulted in an overall reduction of 55,654 feet of drilled shaft construction on the entire project, a savings of approximately 16.5% over the preliminary design.

By B. C. Slocombe

A large derelict inner city site was regenerated for use as a distribution warehouse. Difficult topography and soils conditions required the adoption of a combination of specialist geotechnical processes. Particular attention was paid to the preparation of the site, programming and capabilities of each technique as additional soils information became available.

Jan 1, 1989

By Carl-Oscar Nilsson, Åke B. Nilsson

"The embankment dam at Storfinnforsen is 23 m high and was completed in 1954. The dam has an impervious zone with timber sheet piles and a support fill of glacial till. The pore water pressure in the downstream shoulder has during recent years increased due to deterioration in the sealing function of the timber sheet piling. There is a concern that the high pore water pressure in the glacial till will cause internal erosion initiating at a thin coarse transition layer between the glacial till and the rock fill along the downstream toe. As a remedial action in order to improvement of the leakage resistance a supporting berm of coarse rockfill against the downstream slope of the dam was constructed in year 2013. In addition a new impervious seal in the centre of the dam e.g. a diaphragm wall was considered. However, after further studies and a trial stretch of 40 drains each 20 m long and diameter 0.3 m an alternative with vertical drilled drains in the downstream support was selected. A contract has now started up to drill in a similar way to treat the full length of the dam with drains. The work is in the planning to be completed in 2016.Dam ConstructionStorfinnforsen Embankment Dam was put into operation in 1954. The dam is 330 m long and maximum height is approximately 23 m. The dam is constructed with a central core zone and supporting zones of earth and rockfill on the upstream and downstream sides giving an almost symmetrical cross-section about the dam axis, see Fig. 1. The upstream slope is 2H:1V down to el. 270 and 2.5H:1V below. On the downstream side the slope is 1.75H:1V down to +269 and 2H:1V below. The core zone consists of a timber sheet pile wall with a Zone 5 of glacial till, approximately 2 m wide, adjacent to the wall on the upstream side."

Jan 1, 2016