Search Documents

By B. B. Broms

A method for calculating the bending moment induced in misaligned or bent piles is described, The maximum bending moment varies with the angular rotation between the pile segments, the coefficient of horizontal subgrade reaction of the soil and the flexural rigidity of the piles. A case history involving damages to misaligned 365 x 365 mm square precast concrete piles is described.

Jan 1, 2010

By Chu E. Ho, Paul Napoli

This paper presents the performance of nineteen open-ended steel pipe piles driven through highly variable overburden soils into glacial till and schist bedrock. The piles were 16 inches in diameter and 0.656 inches thick, with yield strength of 50 ksi. The piles were designed for a service capacity of 250 kips and were driven to achieve an ultimate geotechnical capacity of at least 500 kips. Due to the large variation in the ground conditions, installed pile lengths ranged from 25 to 66 feet. Some piles were driven to refusal on the bedrock while others were terminated at final driving resistance of 2 to 7 blows/in. Two piles were suspected to be plugged during driving while others did not. Each pile was instrumented with strain gages and accelerometers near the pile top, and observed using a Pile Driving Analyzer (PDA) to provide preliminary guidance on pile capacity achieved at end of initial drive (EOID). The influence of plugged and unplugged pile toe conditions on the interpretation of pile capacity was investigated using Case Pile Wave Analysis Program (CAPWAP). Characteristics of driving energy, compressive and tensile stresses developed in the steel pipe piles, and the resulting pile deformation behavior are discussed. INTRODUCTION The Hunters Point South redevelopment in Long Island City, Queens is one of New York City’s major efforts to transform former manufacturing zones into mixed developments for the middle-income community. The site is located along the eastern shoreline of the East River and Newtown Creek. The development included low to high-rise residential buildings, a public school and retail structures. Open spaces were created along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community related activities. Waterfront structures included small park buildings, walkways and viewing platforms with the shoreline protected by revetments as part of the City’s flood mitigation strategy. The project was implemented in two phases, with completion of construction for Phase 1 in 2013 and Phase 2 in 2019. Based on available historical information, extensive reclamation took place between 1855 and 1898. After 1951, changes to the shoreline were made along the East River, including the removal of reclaimed land along the northern portion of the project site to allow for docking facilities. By 1977, these facilities had been demolished and backfilled to form the current shoreline configuration. The present site was temporarily used as a parking lot with stockpiles of fill mixed with construction demolition rubble, rip-rap and boulders of varying heights across the site. The existing ground surface varied significantly up to approximately 25 feet difference in elevation. The stockpiles were removed and the site was re-graded during final development of the project. This paper discusses the foundation design challenges due to the loose overburden soils and potential obstructions within the fill material, in particular, the issues relating to installation of open-ended steel pipe piles through the ground conditions encountered on site.

Jan 1, 2019

By Pathik Deb Mallik, Shyamal K. Mitra, Rajiv Kishore, Shuvranshu Rout, Manos De

"This paper presents a case study on the design and construction of a deep underground pit structure constructed inside almost a century old existing plant building. The complexity and challenge for the design and construction lay in executing the work in a difficult subsoil condition especially the presence of deep mica schist. The limited space availability in the existing plant for construction work without hampering regular production in other adjoining areas of the plant made the execution more challenging. Experience with difficult subsoil and proximity to old foundations entailed a non-conventional engineering approach while ensuring complete safety in spite of maintaining the normal operation.INTRODUCTIONTata Steel Processing and Distribution Limited (TSPDL) is a subsidiary unit of Tata Steel Limited (TSL) having a CR processing facility inside the premises of Tata Steel Limited. TSPDL intended to install equipment for a new slitting line inside the existing shed including construction of very deep structure called “loop pit” where the strips from cut CR sheets collect in the form of loops and are recovered as scrap. The entire plant is located within the shed of existing plant. The construction of all foundations including the loop pit is to be executed in the limited area without disturbance to normal production work in balance areas of the plant and also maintain safety and integrity of existing structures.The existing shed is an old structure constructed approximately 80 years ago. The building column foundations are gravity type design of brick masonry supporting only the vertical load from the columns. This type of foundation designed with no eccentricity of loading provides no allowance for implementing any foundation stabilizing design. The present project required civil construction for the new equipment foundations safely within this area."

Jan 1, 2015

By Amr Sallam, Ahmad Mohamed, Mohamed Alrowaimi

Renewable energy, in the form of wind and solar, has emerged as main source of energy in the modern society. The wind industry has substantially grown over the last two decades to become a key player in providing energy to public. Wind turbines are getting larger, taller, and more efficient every year. The foundation is a major component of the wind turbine system. The wind turbine foundation must provide short and long-term stability for the overall turbine to allow continuous and safe turbine operation for energy production. The turbine serviceability and stability requirements must be geotechnically and structurally satisfied. In North America, major foundation types currently utilized in the wind industry include gravity spread foundation, mono pier foundation, and pile foundation. In this case study, a Post Tensioned Pile Cap (PTPC) foundation was used to support a 3.15-3.4 Megawatt turbine with 125M Rotor supported on 87.5M-hub-height tower. Soil anchors in the form of Auger-Pressure-Grouted-Displacement (APGD) piles and Continuous Flight Auger (CFA) piles were utilized. Four distinct subsoil conditions were identified, and for which four pile designs were adapted. Due to the occasional encounter of stronger soils at 50 to 55 feet (15.2 to 16.7 m), shorter pile design was preferred. To satisfy the design uplift load, pile post grouting were utilized to increase the shaft capacity of the piles. In this paper, the pre-production pile load test program will be described. The pile load test procedure, analysis, and results will be presented. A discussion will be provided, which led to the selection of the optimum pile design to support the high tension loads taking into consideration pile length limitations.

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is a very popular applied seismology site characterizing tool within geotechnical engineering. A challenging aspect of DST is to characterize the acquired seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. BCE has invested considerable resources into developing Seismic Trace Characterization (STC), which uses various independent parameters of the acquired data at a particular depth. Initial work in this area resulted in the selection of the linearity estimate from the polarization analysis, the cross correlation coefficient of the full waveforms at the particular depth and the preceding depth and a uniquely developed parameter referred to as the signal shape parameter for this characterization. Subsequent analysis in STC identified two other parameters: the Signal-Noise-Ratio (SNR) and the Peak Symmetry Differential (PSD). The paper briefly describes these parameters and then outlines how they can guide the data analysis to derive more accurate results, especially near surface, which is especially important to assess the liquefaction potential in areas prone to earthquakes, such as California. The process will be illustrated with actual data from another area prone to earthquakes, namely New Zealand. 1. INTRODUCTION The near surface characterization of low strain in-situ shear wave velocities (VS) has proven critical for liquefaction assessment. Liquefaction is a phenomenon in which dynamic loading of saturated soil results in the material properties to change suddenly from a solid state to a liquefied state. VS is an important parameter for evaluating liquefaction potential due to fact that it is influenced by many of the variables that influence liquefaction (e.g., void ratio, soil density, confining stress, stress history, and geologic age (Andrus et al., 1997)). Aki and Richards (2002) also outline that the amplitude of ground motion should depend on the density and shear wave velocity of near surface soils and rocks according to the theory of wave propagation. Since the change in density with the increase in depth is relative minor compared to that of the shear wave velocity, the latter is a very useful parameter to represent site conditions (Stewart et al., 1997). Bray (2014) and his colleagues carried out an extensive geotechnical analysis of the catastrophic liquefaction that occurred in Christchurch, New Zealand in 2010 and 2011 and found that near surface rather than deep liquefaction resulted in extensive foundation damage.

Jan 1, 2018

By F. W. Liang

The geology of pearl River estuary belongs in strong weathered rock quaternary geological systen, so the conditions are complication. Since 80's we built the first deepwater wharf of Shenzhen chiwan port which has 3 berths of 10000 dwt, We have built 3 berths for vessels of 40000 dwt both in Shekou Port and Chiwan port. The berths for carriers of 10000 dwt in Yantian Port of Dapeng Bay are constructing now. In the five years, We built more than 20 deepwater berths of 5000 dwt to 40000 dwt. This paper will introduce how to solve the difficulties of the complex geological conditions and how to use the new fashion construction. We will reduce the period of engineering construction and get good quality and make a good beginning of rapid development of port construction in ShenZhen Special Economic Zone.

Jan 1, 1991

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan, Joseph Toth

The difficulty in material characterization and the erratic response of cemented soil layers, such as caliche in the Las Vegas valley, creates challenges for practicing engineers to reliably predict the response of deep foundations. The focus of this paper is the numerical prediction of axial response in drilled shaft foundations, which are commonly used in infrastructure projects (i.e., bridges and tall buildings) in Las Vegas, NV. The prevalence of hard caliche layers with variation in the degree of cementation add to the complication in numerical modeling. In this study, the applicability of two existing t-z models, developed for Florida limestone and soft rock, was evaluated based on numerical simulations of three bi-directional load tests conducted at caliche-dominant sites. The corresponding top-down load tests were also simulated for further assessment. A MATLAB-based finite-difference program, NVShaft, has been used to implement the mentioned t-z models in axial load analysis. Complexity originating from drilled shaft construction and the interaction with caliche during one axial load test resulted in a stiffer predicted response compared to measure data. For the other two load tests, both t-z models produced comparable load-displacement responses. It was observed that the t-z model for Florida limestone predicted relatively stiffer responses and higher drilled shaft capacity.

Sep 8, 2021

By D. A. Greenwood

Dr David Greenwood opened the first technical session of the conference by highlighting the diverse nature of the papers in this session but drawing attention to the common theme that each solved a particular problem. PAPER 1.1 Tony Elliott introduced his paper on deep mix-in-place soil/cement stabilisation by stressing its simplicity. The engineering solution adopted at Elland was detailed in his paper and had formed the key to success of the project. The process itself is not widely used or known in the UK, although it has the potential to achieve significant benefits, subject to proper engineering control being exercised. It was explained that although the concept was not new, development of the technique for soil modification was relatively recent. The alternatives to mechanical mixing are injection, which is very dependent on soil type, site geometry, etc, and jet grouting; both processes are soil-responsive, and not easily monitored or programmed, difficulties which can largely be overcome by mixing. To achieve this at depths to say 30m requires high-powered, high torque machines and has resulted in significant equipment development.

Jan 1, 1991

By Patrick van der Schaaf

"During 2016, foundation piling works were completed to allow for the construction of a production and storage/handling terminal in Rotterdam. It is there that steel foundations will be produced for offshore wind farms and the oil and gas industry. Several Dutch contracting companies were involved in constructing: foundations for an assembly hall, a barge quay and a deep-sea quay wall. For the hall foundations, cast in situ concrete vibro piles were created. Open ended steel casing piles were also installed due to very high cone resistances which made it impossible to perform cast in situ piles in certain areas. The quay wall was constructed with open ended steel casing piles in combination with sheet piles. A deep-sea quay wall was also constructed to provide enough storage area for the offshore mono piles. This project was unique and challenging due to the use of different foundation technologies in challenging circumstances and soil conditions. This paper will give an insight into the Dutch use of varying foundation piling techniques for deep-sea quay wall constructions. It can be concluded that even experienced local contractors can be surprised by variations in soil conditions. It will also show how the contractors adapted to the difficult circumstances.PROJECT OUTLINEThe project consisted of a barge quay near the assembly hall with a length of 500 metres, width of 42 metres and a height of 35 metres, and a deep-sea quay wall 480 metres in length. This paper concentrates on the foundation works for the construction of the deep-sea quay wall. The construction of the deep-sea quay wall consisted of a combination of open ended steel casing piles with a diameter of Ø 1420 mm and a wall thickness varying between 21 and 23 mm. The lengths of the steel casing piles varied between 32 and 37 metres. Between the steel casing piles triple PU 28 sheet piles were installed with lengths varying between 26 and 29 metres. In the Netherlands, a combination of open ended steel piles and sheet piles is known as a “combi wall”. For the deep-sea quay wall a steel combi wall was shored with steel H- section profiles that were driven in a raked position whilst being injected with grout, so called MV-piles. The MV piles for this project consisted of steel HEB 600 sections with lengths from 52 up to 59 metres and were installed with angles varying between 42.5 and 47.5 degrees. For a detailed overview regarding the project specifications reference is made to table 1 which is presented below."

Jan 1, 1900

By J. Nakayama

For installation of round steel piles or cast-in-place pile construction through boulder contained ground or rocky formation, usual system does not function properly or impossible to work. This paper introduces an installation system which combines unique mechanism where the drill is installed on the top of a driving round steel pile or a stand pipe which is initially driven into the overburden to the depth of self-standing. When the pile driving or bore hole drilling encounters hard strata or boulder contained ground, hard material shall be crushed by the down-the-hole chiselling operated in adjustable short stroke and high frequency of blows while cuttings are discharged in reverse circulation through central reverse pipe while round steel pile is simultaneously stroked by a hydraulic hammer. The paper shall explain the mechanism of the system and introduces construction examples for bridge foundation and piled jetty.

Jan 1, 1999

By Giovanni A. Bonita

The new Embassy of the Peoples Republic of China in the United States (Chinese Embassy) is located in the Embassy Row portion of Northwest Washington DC. The 475,000 ft2 (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. The structure approaches the property line on all sides, and is immediately adjacent to several foreign embassies and a secure U.S. Federal Building. A vertical soil nail wall was used as the primary support of excavation (SOE) system for the project. The soil nail wall was irregularly shaped, benched in areas, and reached total heights up to 98 feet (29.9 m). The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Tight excavation requirements were defined for the project due to the location of the building relative to the property line, requiring fairly precise wall positions and shotcrete tolerances. Design challenges included soft soil conditions, inside wall corners, underground utilities, and seismic impacts from blasting. The paper will focus on the design, construction, and performance of the soil nail SOE system, as well as touch on the logistical and political factors that influenced the design. The paper also notes the Value Engineering and communication approaches that were generated during construction. These efforts resulted in a significant improvement in the quality control and quality assurance exhibited on site, expedited the schedule, and led to significant cost savings to the contractors, engineer, and owner.

Jan 1, 2006

By S. Doombos

To convert the railway-bridge across the Oude Maas between Dordrecht and Zwijndrecht into a vertical lifting bridge, a drastic adaptation of the existing piers is necessary. Extra piles have to be placed quite close to the present piers to bear the extra weight of lift-towers and bridge-sections. This article describes the special technology applied to drive steel tubular piles l800 mm. in diameter and 36 m. in length vibration-free into position. At the same time a method of pile-point-reinforcement has been applied to minimize the settlements.

Jan 1, 1989

By Venkata Krishnaiah Yeddala, Sai Vivek Adari, Suresh Kumar Velugu

Assam cancer care foundation (ACCF) proposed the construction of hospitals and related facilities across 18 locations in the state of Assam-India. Tezpur is one among the 18 locations of Assam with high seismic risk. The strata at the site are comprised of mostly fine silty sands of lower SPT- N values. The water table is also encountered and ranging from 1 m to 2 m below EGL. Since the site lies in seismic zone V as per IS 1893, detailed liquefaction analysis is carried out for all five boreholes and indicates that soil is liquefiable and ground improvement is inevitable up to a depth of 15 m below existing ground level. To mitigate the liquefaction potential and enhance the seismic performance of the soil, ground improvement using stone columns by Wet top feed Vibro-replacement method is proposed. Also, the differential settlements can be avoided effectively under the raft foundation with Vibro Stone Columns. In this paper, field test validation results such as Pre and post-SPTs and ECPTs to access the extent of ground improvement, along with other information adopted in this project presented.

Nov 1, 2022

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By Pete Howell, Patrick Granitzki, Alicia Plinio, Janitha Batagoda

The New York City Housing Authority (NYCHA) Red Hook Houses was subjected to damage during Superstorm Sandy. As a result, the NYCHA has an ongoing project known as Restoration Associated with Sandy Recovery Program to improve the resistance against future storms. The specific project included 28 residential buildings and several service buildings within the Red Hook Development. The subsurface conditions within the eastern portion of the site included existing fill material underlain by varying stratums of very loose, loose and medium dense silty sands followed by very soft to medium stiff clay or dense silty sands. The western portion of the site included existing fill material, very loose to medium dense silty sands and organic clayey silts underlain by very soft to medium stiff sandy silts. Based on the geotechnical report, a conventional driven steel pile system was specified containing two pile depths. As part of the project bidding, an alternative pile type was recommended and analyzed to provide quicker installation, reduce vibrations, reduce noise, and provide relatively large cost savings. Due to relatively high lateral loading, an innovative double steel casing drilled displacement piles was proposed as the alternative pile option. Field testing proved the piles capable of the required project capacities and the use of drilled displacement piles as the best alternative for the project and accepted by the NYCHA.

Oct 1, 2022

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By Robert L. Parsons

This paper describes the results of a detailed analysis of a loess deposit at the deep foundations test site established by the Kansas Department of Transportation. Multiple CPT, SPT, and pressuremeter tests were conducted as part of the investigation. This paper includes an evaluation of the effectiveness of common correlations used with the CPT, SPT when used for classification of loess and estimating its properties. Results show that common correlations must be used with caution as significant errors in estimation may result from using methods developed for other soil types. Laboratory testing included direct shear, triaxial, collapse, and consolidation testing, with many of the tests conducted on both vertically and horizontally oriented samples to evaluate anisotropic behavior. The results showed that strength properties could be considered to be isotropic.

Jan 1, 2009

By Stephen T. Young

The construction of Phase 2 of Hong Kong Station, its retail podium and International Finance Centre Two, the tallest building in Hong Kong, will be completed in the middle of 2003. This paper describes the design and construction of the slurry wall for the Station (both Phase 1 and Phase 2) and the two commercial buildings at the Station. The slurry wall is used as the permanent earth support wall for the station box and the excavation depth ranges from 70 feet to 120 feet. Top-down construction technique was adopted to support the excavation of the station, while circular cofferdams relying on hoop stiffness were constructed to support the basement excavation of the two towers. The designed behavior of the slurry wall is also compared to the as built behavior.

Jan 1, 2003

By Donald Bruce, Alex Reeb, George Filz, Wesley Schmutzler, Mitsuo Nozu

"One million seven-hundred thousand cubic yards of deep mixing were installed to support an elevation raise of an earthen levee known as LPV 111, which is located in east New Orleans. The deep mixing was done by two contractors using somewhat different technologies, but producing elements of the same size. As part of the quality control and quality assurance program, 507 deep-mixed elements were cored and 5,082 specimens were strength tested in unconfined compression. This paper presents data from the coring and testing program. Very high percentages of the core run lengths were recovered, except during one period for one mixing technology. The coring methods are described, and reasons for the isolated episode of low recovery are discussed. The strength data show that the specification acceptance criteria were satisfied. Statistical parameters of the strength data are provided, and trends between strength and the following factors are discussed: depth, soil type, binder factor, and project-specific experience. Photographs of longitudinal cuts of core specimens are presented. Important lessons learned from this unusually large project are described.INTRODUCTIONThe Lake Pontchartrain and Vicinity Hurricane Protection system included a project known as LPV 111, which is an approximately 5-mile long segment of levee and floodwall located in east New Orleans along the Gulf Intracoastal Waterway and adjacent to Bayou Sauvage National Wildlife Refuge (Cali et al. 2012). The majority of the project consisted of a raise of an existing earthen levee from an existing crest elevation of about 18 ft to a new crest elevation of about 28 ft. The underlying soils were weak and compressible, providing inadequate support for the raised levee. Ground improvement in the form of deep mixing was selected to provide the necessary stability and settlement control for the raised levee.The US Army Corps of Engineers (USACE), New Orleans District, was the governmental agency in responsible charge of the project, including approval of design, construction, and payment. The lead designer was URS Corporation, and the general contractor was Archer-Western-Alberici (AWA), working in alliance with TREVIICOS South (Trevi), who, together with Fudo Construction (Fudo), performed the deep mixing.As part of the quality control and quality assurance program, over 500 production deep-mixed elements were cored, the cores were carefully logged, and over 5,000 unconfined compression tests were performed. In addition, selected specimens were carefully photographed before and after longitudinal saw cuts to expose the interior of the specimens. This paper provides a summary of the coring and testing performed on the production deep-mixed elements."

Jan 1, 2015

By Timothy C. Siegel

This report presents the results of a synthesis on the design and analysis of ground improvement for liquefaction mitigation. The synthesis included an industry survey concerning the practice of ground improvement for liquefaction mitigation. Participation in the survey was solicited by advertisements in several trade magazines and by e-mail for the DFI membership. The survey participants numbered 150. Their professional roles include consulting engineers, specialty contractors, design engineers, government engineers, and academicians. They represent a variety of geographical areas including North/Central/South America, United Kingdom, Middle East, Caribbean, Hawaii, Japan, India, Egypt, France, Australia and New Zealand. Upon completion of the survey, several professionals in the field of liquefaction and ground improvement were interviewed for them to elaborate on the survey results. The interviews are included in the Appendix of this report. Financial support for the project was provided by DFI and Dan Brown and Associates PC. The concept of the liquefaction mitigation synthesis was developed by DFI?s Ground Improvement Committee in recognition that: (a) The results of recent research and post-earthquake reconnaissance have challenged previously longheld beliefs about liquefaction and associated mitigation techniques, and; (b) The DFI membership and the engineering/construction industry are interested to know if and how engineers and designers are subsequently adjusting their practice in consideration of recent research and post-earthquake reconnaissance. For more detailed information on recent research and post-earthquake reconnaissance, presentations are available from the State-of-the-Art Forum: Liquefaction Consequences and Mitigation that was held in St. Louis in 2012. A commentary of the state-of-practice in ground improvement for liquefaction mitigation (prepared by DFI?s Ground Improvement Committee) is included in this issue of the DFI Journal. The author would like to thank the participants of the survey and especially Mr. Mike Jeffries, Dr. Les Youd, and Dr. Ikuo Towhata for their willingness to share their expertise in interviews. The author also acknowledges Mary Ellen Bruce of DFI, Billy Camp of S&ME, Inc., and Marty Taube of DGI Menard (and Chair of DFI?s Ground Improvement Committee) for their signifi cant contributions.

Aug 1, 2013