Search Documents

By Walid El Kamash, Sadik Oztoprak

"Soft soil presents a challenge against multistory buildings in some cities of Egypt such as Port Said due to the consolidation settlement. Deep mixed (DM) columns are used to improve the soft foundation soil in order to reduce the total and differential settlements. Latest research revealed that this improvement technique also increases the rate of mechanical consolidation due to column yielding caused by stress concentration from the soft soil. In this study, extended poly-styrene (EPS) Geofoam is used to replace the soft soil over DM columns in order to control the stress concentration and settlement. To understand the effect of EPS geofoam on the degree of consolidation, stress concentration and settlement, a parametric study was carried out through a mechanically and hydraulically-coupled numerical method. A unit cell model is used, in which the soil was considered linear elastic; DM column and EPS Geofoam are elasticplastic materials. Results reveal that EPS geofoam is helpful for reducing the settlements and accelerating the consolidation. Increasing the length of the column of the deep mixed foundation with EPS geofoam has a significant effect on accelerating the consolidation.INTRODUCTIONExpanded polystyrene (EPS) geofoam is a lightweight polymeric material which is made by expansion of raw plastic beads. The expansion of the EPS beads are spherical-shaped particles containing closed hollow cells. EPS which plays an important role as an innovative lightweight construction material is now well recognized due to its low density in addition to high compressive and rupture strength. Inglis (1996) reported the first use of EPS geofoam as a seismic buffer to reduce potential seismic loads against a nonyielding basement wall. Gaskin (2000) and Bathurst et al. (2007) carried out reduced-scale shaking table test on a rigid retaining wall protected by EPS geofoam. The test data showed that the peak lateral loads acting on compressible model walls were reduced below values measured for nominally identical structure but with no compressible inclusion. Abdelrahman and El Kamash (2014) investigated the behavior of EPS Geofoam beneath raft foundation on soft soil of Port Said. They showed the ability of EPS to control vertical displacements. The investigation of the behavior of EPS geofoam with DM column has not attracted more attention of previous researchers. In this paper, the behavior of replacing the soft soil by EPS geofoam was examined in the presence of DM column."

Jan 1, 2015

By James M. Tantalla, Roderic A. Ellman, W. Allen Marr, Scott R. Bamford

"Construction of the powerhouse for the Willow Island Hydroelectric Project required a 100-ft deep excavation inside the limits of a cofferdam and embankment-seepage cut-off wall through soil and rock adjacent to the Ohio River. Portions of the rock had preexisting weak plans and slickensided surfaces with low frictional strength. Stability analyses were performed for critical sections of the excavation to evaluate the stability of the soil slopes and rock cuts using buckling, tension crack, and limit equilibrium analysis techniques. Loading conditions included the 100-yr and intermediate floods, normal pool, sudden drawdown, and seismic design conditions.Stability analyses indicated adequate factors of safety for soil slopes and for rock cuts through the landside embankment sections. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated unacceptable factors of safety. Consequently, the riverside portion of the excavation required measures to increase stability. Long, high-capacity rock anchors and deep dewatering wells to lower the site piezometric head were chosen for this purpose.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. Required rock anchor loads varied from 1,968 to 2,074 kips. The designed anchors consisted of multiple, seven–wire strands with up to 59 strands per anchor. Bond lengths used an allowable bond stress of 100 psi based on the rock bond measured with pull-out tests. Maximum bond and anchor lengths were 50 ft and 140 ft, respectively. Measurements of forces in selected strands and displacements of the excavation showed excellent performance."

Jan 1, 2017

By Peter A. Thompson, Richard E. Prust

"The Bangkok Mass Rapid Transit (MRT} Chaleom Ratchamongkhon Line project is the first underground subway to be completed in Thailand. It consists of 22 km (14 miles) of twin-bored tunnels and 18 cut and cover stations constructed within the deltaic deposits that underlie the city. This paper describes the ground conditions, site investigation, including the use of the self-boring pressuremeter and the associated design issues for the construction of deep foundations. The paper also describes a selection of the various deep foundation solutions that were adopted to address particular constraints of the project and the ground conditions, including slurry walls for the cut and cover stations and foundations used for the underpinning of existing structures.INTRODUCTIONThe MRT Chaloem Ratchamongkhon Line Mass Transit Underground Railway comprises approximately 22 km (14 miles) of tunnels and 18 stations. The route is shown in Figure 1.The project was divided into two design and build contracts. The northern section was awarded to the ION joint venture, composed of Italian-Thai Development PLC, Obayashi Corporation and Nishimatsu Construction Co Ltd. Arup were contracted by ION for the design of the northern section. The section comprises 11 km (7 miles) of twin-bored tunnels, nine cut and cover station tunnels constructed within perimeter slurry walls using top down construction methods, and two cut and cover tunnel structures.The majority of the route of the northern contract follows existing highway Rights of Way. This results in the tunnel alignment passing through the foundations of existing highway bridge structures for which a variety of deep foundation solutions were adopted to underpin these structures.An 8-story park and ride building in the Lat Phrao area was also constructed using deep foundations."

Jan 1, 2005

By Trent Dreese

For critical velocities in gravel units we use Bush-Luckner, Sichardt, other empirical equations, and equations derived from laboratory experiments too. On the base of these, we compiled critical velocity - permeability coefficient dependencies. Under the lower border of these dependencies sand particles can't be moved, and thus they are stable. For critical velocities in the fissures of flysh and volcanic rocks we use Ronzhin (1974) criteria derived from laboratory experiments in Russia. Maximal filtration velocities measured by tracer methods in gravel soils and in fissured rocks have smaller values then the critical ones.

Feb 10, 2003

By Frank Haehnig, Harald Krenn, Harm-Christoph Claassen

"The Wadi Dayqah Dam Water Supply Scheme represents one of the most important projects implemented by the Sultanate of Oman to ensure sustainability of water resources. The principal components of the project comprise two dams to impound the Wadi Dayqah, to store and supply drinking water to the local area and to Muscat, the capital city of the Sultanate.The Main Dam with a central spillway is a RCC Gravity Dam with a maximum height above foundations of 75m, crest length 400m; the Saddle Dam is a rockfill dam with central clay core, max height above foundations is 49m and crest length 360m. During construction of the Saddle Dam a key trench was excavated to 10m depth and filled with compacted clay connected to the central core of the embankment. Grouting utilizing cement grout was performed as a single line grout curtain prior to each filling operations. Both Dams are founded on soft Siltstone, Claystone, Sandstone and inter-bedded harder limestone.After construction of the Saddle Dam, once water was in the reservoir it became evident in early 2010 that some seepage was occurring apparently from the right abutment. This seepage became more marked when the reservoir first filled to discharge over the spillway in June 2010. In order to reduce the seepage, additional sealing works by drilling and grouting of a three row curtain up to 80 meter target depth were initiated to supplement the existing single row curtain. Part of this project for the sealing works has also been to drill additional investigation holes to provide more information and confirm extend of the additional sealing works and its limits.Züblin Ground Engineering was awarded the Additional Sealing Works Contract. Whilst Equipment was on Site, the opportunity was taken to carry out drilling and grouting on the Left Abutment of the Main Dam to reduce seepage through that abutment and to install additional standpipe piezometer for future monitoring of seepage patterns.Work on this Contract started on site in January 2013 and was substantially completed in January 2015.At the time of Tender Züblin Ground Engineering propose and Alternative Design in the form of a Secant PileCut-Off Wall, 85m long to a depth of 40m with additional drilling and grouting below the foot of the cut-off which was then included in the contractual scope."

Jan 1, 2016

By Lawrence Piccagli

This past spring of 2006, BENCOR installed the concrete reinforced diaphragm walls for the COSMOPOLITAN RESORT & CASINO in Las Vegas, Nevada. The project highlights include the excavation of approx. 326.000 square feet of reinforced diaphragm slurry wall with a thickness of 30 inches and a depth of 100 feet using three reverse circulation trench cutters (hydromills) at the same time. The reinforcing steel cages were fabricated on the 8 acre jobsite and approximately 12,000 cubic yards of 4500 psi concrete was placed via tremie. The jobsite logistics of coordinating three trench cutters and three separate desanding/slurry plants as well as the reinforcing steel fabrication and concrete placement all under a very tight schedule was quite challenging. A second main exercise was the execution of a temporary excavation support. As the excavation depths extends between 66 and 72 feet, five to six rows of temporary tieback anchors were required. Anchor lengths range from 43 -83 feet at a maximum design load of 235 kips.

Jan 1, 2007

By Peter de Kort

Tunnels in urban areas generally require deep excavations in soils under the groundwater table. In The Netherlands uplift loads are generally taken by piles installed into dense sand layers, which are hard to penetrate. To avoid nuisance and damage to the environment, piles often need to be installed using vibration free methods, which also have the advantage of low noise levels during installation. Drilling piles and obtaining a high uplift resistance is a contradiction in itself. Franki has adopted several installation methods based on the injection of grout during drilling and/or post grouting to overcome the difficulty of hard layers. This report presents two projects, situated in Rotterdam and Sneek, where vertical tension piles in floors, subject to high uplift loads, have been used. It also explores a project in Zeebrugge (Belgium), where tension piles are installed at an inclination of 1:1 to anchor a diaphragm wall for a quay construction. Test results presented in this report show, that vibration free and soil displacing piles can be installed in very dense sand layers and that a high uplift resistance can be achieved. It is also shown, that a variety of installation methods is available, even in limited space.

Jan 1, 2008

By Wolfram Groh

New underground floors comprising the complete footprint area of the building structure, were constructed under an existing building in sand, located in the Verdun district of Beirut / Lebanon. The works for the rehabilitation and extension of the Verdun 528 building were carried out between December 1999 and August 2000. A restriction of differential vertical movement of existing load bearing walls and columns had to be respected throughout the construction phase of the new basements. Support measures for the building were taken based on a underpinning system with Bauer SVV preloaded micropiles. The specialty of this underpinning job was that the building loads at the time of preloading and excavation of new basements was substantially less than at final stage. The design of the preloading system was particularly challenging in view of the transition from temporary to final load transfer under variable load conditions. Load transfer was based on the Bauer SVV micropile head system applied in several technical variants. Monitoring of levels of structural elements performed throughout the construction works confirmed that the differential movements of adjacent load bearing columns and walls were maintained within the specified limits.

Jan 1, 2002

By Gust Van Lysebetten, Monika de Vos

The objectives of monitoring geotechnical structures can be very diverse, including optimisation of the design, quality control, long term performance assessment, and approval of innovative execution techniques. In this context, new measurement techniques, based on optical fibres, offer the possibility of accurate strain and temperature monitoring with very small sensors and limited numbers of cables. This paper briefly presents optical fibre sensing techniques and illustrates their application to geotechnical structures by means of some projects, carried out by the Belgian Building Research Institute (BBRI).

May 1, 2022

By K. S. Ho

With the aid of the advanced electronic devices and micro-processors, the quality control of deep foundations can be carried out by Non-Destructive Tests (NDT). Three methods are presented here: the Sonic Logging, Vibration and Stress Wave Analysis Methods. The principles, equipments used, testing procedures and applications are fully described. The correlation of these methods with the conventional tests (mechanical coring and loading test) are studied to give a better understanding of the methods. Several case histories with the test results obtained from a number of sites in Hong Kong and overseas are discussed to show how the pile quality can be examined and especially, how to confirm the effectiveness of remedial works on a defective pile. Recommendation on the percentage of piles to be tested are given at the end of the paper by using statistical method.

Jan 1, 2010

By G. L. Sivakumar Babu, P. Chaithra

"Raft foundations which are used against differential settlements and for carrying heavy loads can still be subjected to excessive settlements even if it is safe against bearing capacity consideration. Providing additional piles under the raft can reduce such settlements to acceptable values. In addition to settlements, the piles also relieve the raft a part of the total load and thus the bearing capacity of the Combined piled raft foundation (CPRF) is improved. Parametric study of response of piled raft foundation has been conducted and the results have been presented. The study is conducted using finite element based software, PLAXIS 2D. The main objective of the paper is to evaluate the parameters that affect the performance of piled raft for an economical and effective design. It has been shown that piled rafts are an economical solution in foundation design compared to raft foundation, for the soil conditions considered in the paper.1. INTRODUCTIONThe aim during the design and construction process of high-rise building foundations in urban areas is to ensure the lifelong safety and serviceability of the new and existing buildings in the neighborhood. In order to realize this aim in a cost-optimized manner, the combined pile raft foundation (CPRF) was developed (Katzenbach et al., 2005). For the foundation of high rise buildings with good subsoil, the simplest structure considered is a raft. But when the subsoil near the ground surface has low load-bearing capacity, high-rise structures are often rested on piled foundations.A piled raft and pile group serves similar purposes, but there are essential differences between them. A pile group is a set of piles that have a pile cap. The piles would be designed to share the pile load at ultimate state. The pile cap would be designed to link the piles together but the contribution of the pile cap to bearing capacity will not be included in the design. On the other hand, a piled raft is a foundation, wherein piles are provided along with the raft so that the total load acting is shared partly by the raft and partly by piles, rather than being dominated by the piles (as in a pile group). Piled raft foundations utilize pile support for control of settlements with piles providing most of the stiffness at serviceability loads, and the raft element providing additional capacity at ultimate loading (Poulos, et al., 2011). Therefore, piles are included in a foundation for two main design purposes: to provide adequate bearing capacity and to bring down the settlements to an acceptable level."

Jan 1, 2015

By Dennis Nottingham

Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971 L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers' experiments, observations and measurements, led to an "H" pile probe design which has produced measured soil density improvements up to 250% using SPT "N60" values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern "Open Cell" bulkhead projects will be presented and discussed.

Jan 1, 2004

By J. P. Burland

The paper describes a number of recent case histories in the United Kingdom where field instrumentation and measurements have played a major role in the design and construction of excavations, piles and foundations. It is shown that the design and construction procedures for deep excavations in London Clay are based almost entirely on the results of field measurements. Examples are given of successful application of such measurements. The present understanding of the behaviour of bored piles in stiff clays and their design is based on a number of instrumented pile loading tests. The results of these tests have led to a radically new concept of pile design in which the piles operate at their full shaft capacity under working loads thereby resulting in considerable savings in design and construction. Some examples of the successful application of this concept are given. Finally it is shown that the present knowledge of the stiffness properties of chalk is based entirely on field observations. An example is given of how direct field measurements were used to solve a foundation problem at the base of a coffer-dam in chalk.

Jan 1, 2010

By Timothy Flaherty

We observed the boiling in the water very close to the water adjacent to where we were drilling. That only happened at the very beginning before it was switched to water flushing. Yes, it was performed with water flush.

Feb 10, 2003

By K. E. Darnell

Drilled pier foundations have long been a favored foundation type for heavily loaded structures. Drilled piers derive their load-bearing capacity from end-bearing, and/or sidewall friction. This type of foundation is used in many geologic settings, including those areas underlain by hard carbonate rock, such as limestones and dolomites. When properly designed and constructed, drilled piers provide high load-carrying capacity in both compression and uplift. However, carbonate rock is often subject to intense differential weathering resulting in the formation of an irregular bedrock surface, sinkholes and caves; consequently, the investigation for, and the design of, drilled pier foundations is often complex. Further, the construction may be difficult and costly. This paper discusses geotechnical investigative procedures which can be employed to develop foundation design criteria and reduce the frequency of changed conditions. Finally, state-of-the-art construction practices and quality control techniques are discussed.

Jan 1, 2010

By Juhyung Lee

Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.

By Daniel Levacher

Pile load tests in site require extensive means of action and time. To get outstanding tests, the environmental test conditions must be perfectly known and acceptable. They concern the support installation, the loading, the access and instrumentation site conditions and the economical aspects. In particular cases as offshore areas, the load tests are not feasible. Moreover the variability of soil characteristics limits the interpretation results at the considered tested site. The use of centrifuge modellling offers an other way to study the loaded pile behaviours. Centrifuge tests lead to parametric approaches which constitute for geotechnical engineers an important data base tor recommendations and design codes. To accurately simulate pile behaviours by checking similitude laws linked to the studied problems, the installation of model-piles must be also representative of the in-situ piles. Driven piles account for a large part of the piles installed through the world, mainly for offshore or harbour constructions. So, to explore driven pile problems by centrifuge tests, miniature pile driving hammers must be developed and tested under macro-gravities. The paper describes two types of these ones in details. They are commonly used at the centrifuge centre of the Laboratoire Central des Ponts et Chaussées - (LCPC) - [Réf. 1] for different deep foundations researches. Performances and limitations are given for both miniature pile drivers and some results from their use are presented to illustrate the suitability of these apparatus.

Jan 1, 1996

By Andrew Baxter

The Crystal Bridges Museum of American Art in Bentonville, Arkansas is a beautiful glass and concrete structure cut into a valley that mingles with water ponds spanned by multiple bridges with suspended roofs. Or, at least it will be when completed in 2009. At Crystal Bridges, most of the proposed buildings involve cuts up to 50 ft high to be retained by the building structures. This requires the construction of retaining walls adequately founded to support lateral loads of up to 70 kip/ft. To add to this difficulty, the site is within a karst region with all the variability and irregularities associated with solutioning and erosion of the parent rock in this environment. The irregular rock profile made it virtually impossible to conceive a predictable arrangement of shallow footings and shear keys for the retaining walls. The existence of layers of soft soils within a hard rock formation made a caisson foundation impractical. The authors developed an innovative solution based on micropiles, which proved to be invaluable from a cost and schedule point of view. In areas where rock was shallow, micropiles were used as ?shear pins? to transfer the horizontal loads to the rock. In areas with significant overburden, a system of vertical and battered micropiles was devised to carry vertical and horizontal loads from the retaining walls. This paper presents a detailed description of the design and installation of the micropiles used as shear pins, and includes the results of lateral load tests performed on full-scale models of the grade beams on shear pins. The work performed shows that micropiles in rock can be effectively utilized for support of significant lateral loads provided that an adequate arrangement of suitably sized micropiles is provided, and that micropiles used as shear pins may develop significant tensile stresses when loaded laterally.

Jan 1, 2008

By I. D. Dayal, Anil Kumar Jain

"Cutoff walls are frequently used to slow down or prevent seepage of water through and/or around dams. Cutoff wall is a type of seepage barrier structure designed to reduce the flow of water underneath temporary or main dam. There are number of techniques for the construction of cutoff walls including concrete, Jet grouting and permeation grouting. NHPC LTD, a premier Govt. of India undertaking has been instrumental in the hydropower development within the country & in nearby countries like Nepal & Bhutan since last four decades. NHPC LTD has completed more than 20 hydro-electric projects with total installed capacity of 6587MW (including capacity addition by JV- NHDC). In all these projects, different types of dams and spillways were constructed in not so benign to extreme challenging geological set up. There has always been challenge associated with the temporary diversion works. The project sites sometimes incur huge river bed excavations in case of concrete gravity dam founded on rock foundation at large depth. The challenges for minimizing the seepage have been well taken care by constructing the dedicated seepage barriers. The construction of cut-off walls have progressed from “conventional continuous trench backfilled with conventional concrete or plastic concrete” to “grout curtain”, to “jet grouting” to the “concrete cut-off wall” , the last being the most sophisticated & credible seepage barrier.The efficiency of the cut-off walls are monitored by the seepage quantity observed (reduction of the seepage flow), uplift pressures or exit gradients after construction of cut-off walls. For construction of the main concrete dam, required space is created by the river bed excavation for placing the dam foundation on sound rock. Sometimes there is deep river bed excavation from 30 to 40 m depth or even more as per the available rock profile. Temporary coffer dams are constructed for diverting the river flow through diversion tunnels / channels etc. In deep river bed excavation; there are high chances of the significant seepage through the coffer dam foundation / river bed material due to high hydraulic gradients. Seepage and piping are the main causes of the failure / damage of the temporary coffer dams. If the seepage quantity is too high, then it becomes difficult to handle it by dewatering in the dam pit. Dam concrete is required to be placed unhindered to have a monolithic construction of dam blocks & to have faster construction in the working season. Cut-off walls increase the seepage path considerably thus reducing the exit gradient and further reduction of the seepage thus helping in maintaining the seepage free area for working."

Jan 1, 2016

By Maurice Guillaud

The most striking innovations on diaphragm-wall construction plant are those associated with continuous real-time trajectory monitoring of the excavating tool (either a grab or a hydro-cutter). The recent equipments are fitted with clinometers and gyrometers to control deflection, rotation or deviation from the vertical, thus allowing to install diaphragm-walls with a verticality accuracy of less than 0.3%. One of the greatest advantages of extensive use of on-board IT systems on the Hydrocutters and hydraulic grab machines is that it aids quality control by automatically producing complete real-time reports of all excavating data (verticality, depth, type of ground, rate of progress, stoppages, etc.). These reports are available to the Engineer, providing the total transparency required for Works Supervision and the Quality Assurance Plan. They also provide the Contractor with input data for databases used for optimising efficiency and progress criteria on future jobs.

Jan 1, 2002