Search Documents

By Michael E. Ameel

The vibrated beam method of installing a vertical barrier wall is one of the least applied techniques, yet given certain site conditions and constraints, it is a cost-effective and proven method of controlling lateral groundwater flows. A recent full-scale application of this technique demonstrated its usefulness at an active manufacturing facility located in Northern Wisconsin. At this site, a 3,233 foot long cutoff wall was keyed into an underlying bedrock, which was located an average of 40 feet below the ground surface. Using a slag cement-clay based slurry, a 1E-7 cm/sec or less, nominal 4-inch wide cut-off wall was constructed using the vibrated beam method. Challenges included working around an active manufacturing facility with minimal access to the work area; installing the wall through a very dense glacial till; minimizing soil excavation volumes of potentially impacted soil; and, working around and adjacent to numerous active utility lines without impacting the facility operations. At utility locations, the vibrated beam wall was supplemented with a jet grout panel wall, without the need to bypass or otherwise interrupt any of the plant?s utilities. Quality control consisted of the monitoring and measuring of slurry parameters, survey control, and real-time monitoring and documentation of all critical barrier wall installation parameters. A vibration monitoring plan was also implemented to measure vibrations at utilities and adjacent facility structures. Proper equipment selection, significant up-front planning and close coordination with the facility resulted in a safe and successful project. The work was completed ahead of schedule during the 2009 construction season.

Jan 1, 2010

By Douglas G. Baker, Jason K. Braund-Read, Megan R. Sheffer

"Mica Dam, owned by British Columbia Hydro, is an 820 ft high earthfill embankment dam that was completed in 1973. The dam consists of a thin central impervious till core supported by upstream and downstream compacted sand, gravel and cobble shell zones, founded on bedrock and valley bottom alluvium deposits. In 2012, a project was started to install new piezometric instrumentation within the dam’s foundation and downstream shell zone.Deep drilling in large embankment dams is very difficult and requires careful planning to select a methodology capable of reaching the target locations, while ensuring that no damage is done to the surrounding dam fill zones. At Mica Dam, the drilling could only be carried out from the Dam Crest and drillholes had to be carefully oriented to avoid intersecting any existing dam instrumentation. The drilling work therefore required angled drillholes, at depths of up to 855 ft, through heavily compacted sands, gravels and cobbles, and to significant depths below the standing water table.During the planning stages for the Project, in early 2013, the preferred drilling method was selected and a drilling contractor was engaged for the drilling work. Critical dam safety concerns were identified and addressed during the design stage of the Project with the drilling contractor, so that risk mitigation measures and response plans could be effectively developed.This paper explains how background information and prior drilling experience influenced the final design and implementation of the drilling techniques used in 2013 to successfully drill the deep holes and carry out the piezometer installations in Mica Dam. Drilling procedures, instrumentation design and installation methods, as well as risk mitigation measures, are discussed."

Jan 1, 2017

By Wang Huichang

A tentative mathod for predicting load-settlement relationship and bearing capacity of single piles based directly on the results measured by cone penetrometer with local friction sleeve is presented. It is possible that the load-settlement curves can be constructed by means of CPT and the problem of both the bearing capacity and the settlement behaviour of single piles can be considered jointly. The proposed load-transfer functions are continuous, positive monotonic and nonlinear. a concept of weight mean point resistance 2D above and 4D underneath the pile base to determine the unit ultimate base resistance of piles is presented. The predicted results of seven jacked piles in loess are in good agreement with the load test data.

Jan 1, 1991

By Meeok Kim, Thornton Tomasetti, Seth Knihtila, Michael Oakland, Shawn Leary

The transformation of Seattle's historic KeyArena into the state-of-the-art Climate Pledge Arena, home to the NHL's Seattle Kraken, was no small feat. The $930-million renovation and expansion required the near-total demolition of the old structure and construction of an 800,000 sqf (74,000 m2), below grade venue while keeping its landmarked façade and roof intact. To do that, the project team had to come up with solutions for excavating 680,000 cu yd (520,000 m3) of soil to make way for the new 17,000-seat arena while working around the massive temporary shoring supporting the 44 million lb (20 million kg) roof all in time for the NHL's 2021-22 season.

Sep 1, 2023

By Joel L. Volterra

Since 1910, Mueser Rutledge Consulting Engineers (MRCE) has regularly provided professional engineering services including inspection of pile load tests. Historically, such services included on-site inspection of the driving of test piles and subsequent static load tests by qualified Geotechnical Engineers. Load testing procedures are specified by local or State Building Codes, locally the 1968 Building Code of the City of New York (1968 BCCNY). Between 1968 and 2008, the 1968 BCCNY required a minimum 48-hour hold period for standard loads per pile type, an extended 96-hour hold period for higher capacity piles, and a settlement criterion that the pile maintain a test load equal to two times the design load with less than 0.012 inches of settlement over the last 48 hours of the hold period. Effective July 2008, the new 2008 BCCNY shortened the hold period and relaxed the settlement criteria to that which is more similar to other governing codes and standards such as the International Building Code (IBC 2006) and the American Society for Testing and Materials (ASTM). MRCE implemented an automated load test monitoring system to reduce costs and to alleviate or minimize overnight and off-hour staffing for load test readings. Initially, a series of linear variable differential transformers (LVDTs) and data loggers were included in the Contractor?s load test setup to electronically record pile head settlement and where applicable, settlement of telltales installed to varying depths in the pile. A pressure gage was subsequently added in the hydraulic line, then a load cell, strain gages, and remote access using modems. The ease of the setup and modular adaptive nature of this system have proven it to be a useful tool and improved our ability to better serve our clients and manage our pile load testing services.

Jan 1, 2008

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By C. Guney Olgun, Charles Elks, Sherif L. Abdelaziz, James R. Martin, Christopher Fox, Pier Luigi Iovino, Fatih Catalbas, Pierre Gouvin

"Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.IntroductionThere is a developing trend around the world to explore alternative energy sources. The main driving forces are growing global energy demand, depleting natural resources and the adverse effects of greenhouse gas emissions from fossil fuel consumption. Geothermal energy is one of the promising renewable sources that can be utilized to offset such trends. However the use of geothermal energy has been limited mainly to certain hot spot areas where it is used either for district heating and/or electricity generation. Ground temperatures below a depth of about 6 meters (20 feet) remain stable compared to outside air temperatures, typically lying between 8-23°C (46-73°F) at most U.S. regions. The constant temperature and heat storage capacity of near surface soils in any region represent a tremendous potential of stored energy that can be used for heating and cooling of structures."

Jan 1, 2017

"Boston’s Central Artery passes beneath nine active railroad tracks carrying commuter and Amtrak trains into South Station, the City's busiest rail terminal. These railroad operations had to remain in service throughout the construction of the “Big Dig”. The solution was to jack the tunnel under the tracks, rather than build the tunnel by more conventional means.Jacking of utility pipes is fairly common, but jacking boxes as big as a highway had never been done in North America, until the Big Dig came along.Soil freezing was decided upon as a means of stabilizing the soil under the tracks. This allows the tunnels to be jacked into place without soil caving when the soil is excavated at the leading face of the advancing tunnel boxes. Hundreds of pipes were driven into the ground between the tracks. Inside the steel pipes were smaller plastic pipes. A freezing plant near the railroad tracks pumped refrigerated brine into the inner plastic pipes. The brine ran out the bottom of the inner pipe, flowed up to the top inside the outer pipe, and was re-circulated to the freezing plant and back again into the ground. Over several weeks the circulating brine drew the heat out of the soil little by little, and froze the ground outward from the pipes. Soil FreezingThe plan required the construction of jacking pits in which the tunnel boxes could be constructed, and from which they could be jacked forward to their final locations, as described in the accompanying article. Once the jacking pit was built and the tunnel box constructed inside the pit, crews made an opening in the headwall of the pit to allow passage of the tunnel sections, excavated about three feet of the frozen soil, pushed the tunnel box ahead, and repeated the procedure again and again."

Jan 1, 2003

By Matthew Janes

The installation of piles and casings is becoming increasingly difficult as restrictions on vibration become common in major urban areas. The use of high frequency, resonant excitation of a pile or casing permits ease of installation of sections to great depths with near imperceptible vibrations as close as 1 pile diameter. The new Resonant Driver is able to excite a pile at its resonant frequency (up to 150 Hz or 9000 VPM) to produce elevated levels of acceleration, force and displacement in the pile. The combination of extremely high acceleration and controlled levels of displacement allow the pile to slice through varied soil with almost no vibration translated into the ground. In direct comparisons between conventional vibrators and impact hammers the Resonant Driver produces less than 1/50th the vibration. The Resonant Driver results in ground vibration of between 1/20 and 1/40 of common limit levels (1 cm/s or 0.5 in/sec) as close as 1 pile diameter. At a distance of 5 m (16 ft) from the pile or casing vibration levels approach imperceptible levels. The Resonant Driver uses a proprietary algorithm to tune the drive vibration to the changing natural frequency of the pile as it is driven into the ground. By maintaining resonance the energy in the pile is built up like in a flywheel on an engine or a child on a swing. This build up of energy aids in driving and significantly reduces waste. Recent experience using the Resonant Driver is proving the technology can drive a variety of steel pile and casing sections through varied soils. Continued use of the Resonant Driver will create a data base of various pile and casing sections, soil types and achieved capacities.

Jan 1, 2008

By W. Morgan NeSmith

A drilled displacement pile program was utilized for the expansion of an existing power plant in Cohasset MN adjacent to the Mississippi River. The drilled displacement (DD) pile is an innovative foundation type that provides exceptional value in some geologies. In the U.S., DD piles have typically been used in coarse-grained soils due to the large friction capacities that can be generated by the piles in these conditions. This project was the first large scale experience for the project team where it was anticipated that significant portions of the DD pile capacity would be developed in primarily fine-grained soils. The project site consisted primarily of variable amounts of fill overlying predominantly low plasticity alluvial silts. In some cases, alluvial silty sand layers were encountered within the expected pile installation depths. Alluvial sands were typically encountered below the silts, in some cases within the expected pile installation depths. The project team developed a probe and pile load test program to address the variable subsurface conditions across the site. The program included monitoring various parameters (including applied torque and tool penetration rate) during the drilling portion of the pile installation using recently developed data acquisition techniques. This data was used to estimate the rig energy, or Installation Effort (IE), required for pile installation. IE profiles from the test and indicator piles were compared with subsurface data available from a number of previous site characterizations. Additionally, Cumulative IE values were compared to an in-house database of IE vs. DD Pile Capacity. Final production pile toe levels were based primarily on IE values selected from this comparison. The IE data collected during production was also used to address large variations in pile-cutoff elevation (relative to a fairly uniform ground surface elevation).

Jan 1, 2008

By Tony Suckling

The commercially available finite element program Plaxis has a key benefit over other finite element analysis programs in that it has a relatively simple user interface to input and output data. This benefit though may also be it?s weakness in that anyone, regardless of their grounding in geotechnical engineering, may use the program and produce results for design. It is essential, as for all engineering design, that the models are checked by competent engineers. This paper describes the key recurring problems found by the authors when checking Plaxis models, such as the generation of the initial in-situ ground stresses and the modelling of groundwater. Interestingly, the authors have not encountered similar problems when checking finite element models produced using other programs and conclude that this may be due to the higher calibre of modeller needed to use these other programs. The geotechnical industry is in a situation at the moment where senior managers who may not have been trained in finite element modelling are relying on less experienced staff who have had some training in modelling, either at university or post graduation. The quality of this training is variable and all organisations running easy to use programs need to be aware of the potential risks and dangers. Management procedures and engineering checks that are essential to validate the results of these models are described, assuming that those in charge are not experienced modellers themselves. The model checking process by competent persons is absolutely essential and it is hoped that this paper will help those organisations that do not have such procedures as part of their own internal Quality Assurance or design validation system. The procedures described are valid for all finite element programs.

Jan 1, 2010

By Matthew C. Janes, Mark C. Spence

"A former coal gasification site next to Rock Bay in Victoria, BC, Canada required a barrier to permit dewatering and excavation of the bay and surrounding property. The adjacent property owners had stringent requirements at the boundaries of their properties. Isherwood Geostructural Engineers designed a temporary steel sheet pile (SSP) water retention structure and excavation shoring system along the perimeter of the site. The project involved challenging geotechnical conditions in soft clay soils and a multi-faceted construction staging plan involving the diversion of two large storm water outfalls that drained into the bay. Despite a well-conceived design and construction plan, unexpected site conditions and delays led to significant changes in design and construction approach. Employment of the Observational Method and on-the-fly geotechnical investigation were instrumental in maintaining project momentum and schedule. The paper presents the geotechnical and geostructural design details and construction events as they transpired, highlighting the key issues, discussions and lessons learned.INTRODUCTIONFor over 100 years, the Rock Bay Site, in Victoria, British Columbia, Canada, had a legacy of contamination left behind from previous industrial activities. The site was the former location of a coal gasification plant that was in operation from 1862 to 1952. The site was also an infilling location for a nearby tannery and sawmill. The remediation of the Rock Bay Site involved the excavation and replacement of approximately 300,000 tonnes of contaminated soils on Transport Canada’s property. The project commenced in 2004 and has occurred over several phases on multiple properties. In the third and final phase of the project, a temporary steel sheet pile (SSP) excavation shoring system and ocean barrier wall – required to seal off the bay – was employed to enable disposal and replacement of approximately 90,000 tonnes of contaminated soils from the shoreline and base of the bay."

Jan 1, 2016

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By Deep Foundation

Whenever an organization launches an initiative, the question arises whether that initiative has staying power. Or is the initiative, as is quite often the case, merely a fad; that is, just an activity that suddenly becomes popular, but which does not stay popular for very long. When the Federal Highway Adminis- tration (FWHA) started its Advanced Geotechnical Methods in Exploration (A-GAME) initiative, that question was addressed, especially considering the fact that up to 50% of major infrastruc- ture projects suffer impacts to schedule or cost due to geotechnical issues. Many of these issues relate to risks identified directly or indirectly to the scope and quality of site character- ization work. Effective site charac- terization is critical for recognizing. potential problems that may affect design and construction and for ensuring safe, well-performing and cost-effective projects. Grounded on that, knowledge of all available site investigation methods should continue to be shared widely and the application of those methods should be encouraged on an ongoing basis throughout the project lifecycle. The A-GAME initiative covers five technologies: Cone penetration testing (CPT), monitoring while drilling (MWD), electrical geophysical methods, seismic geophysical methods, and optical and acoustic televiewers. Of these, three soil and rock investigation methods were highlighted that are underutilized not only here in the U.S., but also in many places around the world: CPT: a well proven and established method for soil characterization that turned 90 last year, in which continuous in-situ data are col- lected quickly and consistently. Geophysics: the science that assesses the physical properties of the soils and rock using seismic and electrical techniques, which con- tinues to advance in leaps and bounds as the application of well- understood technologies become more powerful.

May 1, 2023

By Ivan Hee

The 2.5km long bridge over the Beauharnois Canal and St. Lawrence Seaway is a major structure in the new Autoroute 30 project near Montreal. Foundations for the bridge consist of footings on bedrock, driven piles, and drilled shafts. This paper describes the design, verification, and construction of 1.85m diameter drilled shafts socketed into very strong and abrasive dolomitic sandstone. Two loading tests on sacrificial, heavily-instrumented, 1.18m diameter test shafts using Osterberg load cells were performed, with telltales installed to monitor a possible rock cone failure mechanism. The loading tests resulted in a revision to the initial design and provided a greater understanding of the cone uplift mechanism in rock. Insights gained are discussed and economies of the load testing program presented. Construction methodologies are also presented.

Jan 1, 2011

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which are 2.5 m to 3.0 m (8 to 12 feet) in diameter and extending over 60 m (200 feet) in depth below grade. There are unique challenges associated with constructing such large and deep cast-in-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

Jan 1, 2008

By Raffaella Granta

Mosul Dam is an earth fill dam located on the Tigris River, approximately 40 km (25 mi) northwest of Mosul, Iraq. The construction of the dam was completed in 1984. It is one of the largest multipurpose dams in the Middle East, and the largest dam in Iraq. The dam provides flood control, irrigation, power generation and water supply. At 113 m (371 ft) high and 3.65 km (2.3 mi) long, the reservoir has a storage capacity of 11.1 billion m3 (392 billion ft3) of water. The main hydroelectric power station has four turbines for an installed capacity of 750 MW. The discharge system includes two bottom-outlet tunnels of 10 m (33 ft) diameter, a five-gate service spillway and an emergency fuse plug spillway.

Oct 1, 2022

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more diffi cult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizing tie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State. INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges. Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story offi ce building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall."

Jan 1, 2007

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more difficult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizingtie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State.INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges.Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story office building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall"

Jan 1, 2007

By Gregory M. Landry

"There is an old joke at Moretrench that defines dewatering as “that element of an underground construction project, which, when disregarded, will generate the low bidder.” Sigmund Freud wrote that all jokes are true, and the kernel of truth behind this one is that dewatering is often misunderstood or neglected until the last possible moment in the life of a project. The purpose of this article is to describe commonly used dewatering methods and to clear up a pervasive but fundamental misunderstanding about how to determine the amount of dewatering effort required for a project. The Tools of DewateringDewatering may be divided into two broad categories: (1) methods that remove water from the excavation after it has already entered and (2) methods that seek to exclude or intercept the water before it reaches the excavation. The former is generally self-performed by general or earth moving contractors using sumps and ditches, while the latter is usually done by a specialty contractor. SumpsProperly installed sumps can be an effective and economical way to control water inflow into a site. In this technique, groundwater is allowed to enter the site before being pumped away. Advantages of this method include lost cost, easy availability of equipment and the fact that a general contractor can self-perform the dewatering. However, caution should be used when deciding whether to use this method, and consideration should be given to the following factors:1. How will the soil behave under seepage forces? Will it run, potentially causing ground loss?2. How much groundwater lowering is required? If the groundwater only needs to be lowered a few feet, using sumps will be much more practical than for a situation that requires significant drawdown.3. Will the excavation subgrade soften or otherwise be damaged by allowing water to run over it?4. Is my workforce skilled enough to implement and manage the sumping plan?In the photo, the sump is capturing groundwater that has already entered the excavation by traveling under the sheets. In this instance, the house in the background of the photo was eventually purchased by the project owner after sustaining damage due to ground loss."

Jan 1, 2017