Search Documents

By A. Ortigão, M. Felix, E. Falk, T. Koehler

"Ground improvement techniques such as vibro-replacement or deep soil mixing are fairly young products in the Brazilian geotechnical market. Soft soils in this country are deep, very soft, have low sensitivity and are challenging. In general, ground improvement techniques are increasingly selected as more costefficient and flexible solutions on infrastructure projects compared to the conventionall technologies such as piled embankments, wickdrains with surcharge or jet-grouting. The geotechnical challenge expansion project for the Porto Alegre Airport, South Brazil, involved a taxiway area of five ha of 8 to 10 m of soft clay deposit. The deep soil mixing (DSM) technique was selected as a cost-effective solution to reduce settlements. As part of the design, an extensive soil investigation programme includ ing laboratory and field trials was carried out to define the most economical slurry-recipe, DSM installation patterns and quality control specs. This paper gives details of the field and laboratory trials and present results.INTRODUCTIONThe International Airport of Porto Alegre in the state of Rio Grande do Sul in Brazil is located in an area with extensive sediments near to Guaíba Bay. During the different construction phases of the airport over the last decades, the soft clay deposits have been a challenge for the local geotechnical community as well as for the specialized contractors (Schnaid et al, 2001). As part of the most recent expansion scheme, a cargo-terminal with a five ha airplane tarmac area will be constructed."

Jan 1, 2015

By Gerald Verbeek, Erick Baziw

Dynamic soil analysis (DSA) in geotechnical practice is intimately related to the capability of measuring the necessary soil properties of shear modulus and absorption. In DSA the methods of analysis are based upon the stress-deformation response of soils due to imposed shear strains. Typically the soil profile is numerically modeled as linear visco-elastic system. This technique is referred to as the Equivalent Linear (EL) method, and it requires the specification of the input parameters of low-strain (<10-5) shear modulus, modulus reduction, and the equivalent viscous damping ratio, which is directly related to the soil absorption value. Downhole seismic testing (DST) has proven to be a very accurate tool for estimating low strain shear modulus values as long as source wave raypaths are taken into account, especially for near-surface investigations. DST has also been utilized to estimate low-strain interval absorption values. In these cases standard frequency domain absorption estimation algorithms (such as the spectral ratio technique) are utilized where it is assumed that the source waves are traveling along the same travel path, which is obviously not the case for near surface DST investigations. This paper outlines a unique DST absorption estimation methodology, which is carried out in the time domain and takes into account source wave travel paths. 1. INTRODUCTION There is considerable interest in methods of geotechnical in-situ engineering that provide accurate estimates of the shear wave velocity and the associated absorption values in the ground, since these parameters form the core of mathematical theorems to describe the elasticity/plasticity of soils and they are used to predict the soil response (settlement, liquefaction or failure) to imposed loads (whether from foundations, heavy equipment, earthquakes or explosions).

Jan 1, 2019

By William M. Dalrymple, William P. Owen, Benjamin S. Rivers

For the California Department of Transportation (Caltrans), geophysical applications have played an important role as part of a successful multidisciplinary approach to subsurface characterization for the design of high value structures. Since at least the 1950’s, geophysical methods have been deployed to guide the exploration drilling program and to maximize the return on drilling investment by increasing the amount of data obtained from test borings. Geophysical applications saw increased use beginning in the 1990’s, during the seismic retrofit of the state’s toll bridges and the replacement of the west span of the San Francisco-Oakland Bay Bridge. Over the intervening years, increases in computing power and increasingly sophisticated commercial off-the-shelf software applications have allowed Caltrans to leverage advancements and perform geophysical investigations of increasing complexity and scale. Ultimately, the goal of these efforts is to maximize return on investment, whereby increased investigation costs at the design phase are offset by reduced uncertainty regarding subsurface conditions, leading to reduced cost overruns related to change orders and unforeseen site conditions during construction. These objectives are consistent with the recent Every Day Counts (EDC) initiative to incorporate Advanced Geotechnical Methods in Exploration (A-GaME) into routine engineering practice. Caltrans is an implementation partner of the A-GaME initiative, and Caltrans’ practices represent a model toward the institutionalized geophysical site characterization practices for other transportation organizations. The authors provide a retrospective on 70 years of experience with geophysical applications for transportation infrastructure, with examples and observations on potential future direction of the industry.

By Michael Frawley, Deana Ruud, Jessica Turner

Technology is allowing for new ways to mitigate risk associated with subsurface exploration and unanticipated subsurface conditions during construction. Unanticipated subsurface conditions have the potential to force delays and cost overruns on even the best-managed and well-executed projects. For more than a century, geotechnical professionals have documented the location and conditions encountered in hundreds of thousands of subsurface borings. Utilizing processes for compiling and managing data, owners can streamline site selection and receive access to a conceptual geotechnical model before field exploration takes place. Digitizing historical subsurface information allows for creation of an interactive, web-based platform combining publicly available information and culminating with the opinion of a local, experienced geotechnical engineer. This connectivity aids in the reduction of risks associated with unknown conditions on prospective project sites. Through this conceptual project study, we demonstrate how a project owner would be able to use a comprehensive desktop study to review the expected conditions prior to making a purchasing decision. Following the purchase, the expected conditions would be confirmed through traditional methods, confirming potentially problematic site conditions and the associated risks. INTRODUCTION Preliminary project planning is often based on assumptions made by the design team with regards to site suitability. After due diligence, site development is traditionally initiated by the owner or the owner’s representative when engaging a geotechnical engineer to perform a thorough subsurface exploration at a site. The data generated by the geotechnical engineer’s analysis of the site is required to design foundations, pavements and earth retaining structures and move the project from concept into design. This necessary, subsurface exploration can be time consuming, intrusive, and require significant resources, often when resources during construction seasons when resources are most limited. By leveraging historical data generated from previous subsurface exploration, a more thorough analysis of project risk can be developed prior to mobilizing a drill rig. Ultimately, preliminary budgets and designs are more accurate and geotechnical field exploration is more strategic. The geotechnical engineer’s role transforms from raw exploration and analysis to confirmation of anticipated conditions.

Jan 1, 2019

By Alper Turan, Hesham El Naggar

"The use of aggregate pier foundation systems has become widespread as the engineering practice moves towards cost-effective ground improvement solutions that provide accelerated construction schedules. Increased bearing capacity, effective settlement control and potential for liquefaction mitigation are commonly acknowledged benefits of aggregate piers. This paper studies the mechanisms by which aggregate piers interact with each other and with the surrounding ground when excited by seismic loads. A particular emphasis was placed on the response of a raft foundation supported on a site improved using aggregate piers. Three-dimensional nonlinear finite element analyses were conducted using commercial software package, ABAQUS. Non-linear soil behaviour is modelled using a three-dimensional total stress-based bounding surface plasticity model, which is able to simulate stiffness degradation and damping increase in the soil. The soil stratigraphy considered in this study was a 30 m deep soil deposit that comprised a very stiff base layer and a shallow soft surficial clay layer. Ricker Wavelet time histories with different frequency contents are used as the excitation force in the analyses. Various area replacement ratios (ARR) for aggregate piers are studied for a square plan layout. The results presented in this study are considered to be of interest to researchers and designers in evaluating the seismic ground response of the sites improved using aggregate piers. INTRODUCTIONThe schedule and cost limitations imposed by the traditional over-excavation and replacement method for the stabilization and settlement control for poor soils resulted are underlying factors for the significant increase in the use of aggregate pier foundation system, particularly in the last two decades. Various well known advantages of aggregate pier systems including increased bearing resistance, settlement reduction, and increased uplift capacity have been studied by various authors. The use of aggregate pier systems for settlement control in soft soil deposits was studied by various researchers including Lawton and Fox (1994), Lawton et al. (1994) and Wissmann et al. (2001). Lien and Fox (2001) studied the behaviour of aggregate pier systems supporting embankments and retaining walls. The stabilization of slopes by means of aggregate piers was studied by Lien and Fox (2001), Wissmann et al. (2002). Thompson et al. (2009) reported on a performance monitoring study of aggregate pier systems supporting MSE walls. The interaction mechanism between the aggregate pier system and the surrounding soil attracted attention of various researchers. Handy and White (2006a) and (2006b) studied the changes that occur less than 2 m from centers of the piers, and further away, respectively. The support mechanism of aggregate pier systems subjected to compressive loading were studied experimentally and numerically by White et al. (2007) and Pham and White (2007), respectively."

Jan 1, 2017

By Javankhoshdel Yacoub

Piles are often used to reinforce slopes as they increase the available restoring force when calculating the factor of safety against sliding. In this paper, a 3D model of a slope containing multiple modes of failure is reinforced using pile elements. The results of the 3D Limit Equilibrium analysis containing piles are obtained using a newly introduced coupled approach which combines the results of finite element analysis (to obtain the displacement of soil along the pile) with the traditional limit equilibrium iterative formulation. The multiple modes of failure are obtained using the novel Multi-Modal Optimization (MMO) metaheuristic method which adapts the Particle Swarm Optimization (PSO) method to search for multiple local minima in a single slope model.

Oct 1, 2022

By Hitendrabhai S. Dewangan, Dr. Aashish A. Mehta

Pile foundation is widely used in construction of marine structures. In offshore & marine piling work, drilling/boring supporting fluid is used to stabilize the borehole (excavation) prior to tremie concrete. The poly-fluid is a synthetic drilling granular polymer characterized by high molecular weight.it is mainly used for the preparation of stabilizing and lubrication mud in drilling of deep foundations. Disposal of polymers after using it into the sea, pollutant the sea environment, which may be harmful for living organisms inside sea. To reduce the pollution in offshore/Onshore, it is essential to take the precautions during flushing operation with proper recycled, reused & it’s Disposal. To provide economic and environmental solutions, used slurry was treated with addition dose of fresh material/polymers. The amount of fresh materials/ Polymer to be added can be decided based on (viscosity, density and pH value) test results. Finally, initiate water flow and air agitation as required. Run the tests on the re generated slurry before transferring to storage tank. Also, after storage, polymers will be reused for next operation. Moreover, mud wastage coming from borehole will also be disposed at suitable dumping places.

Sep 1, 2022

By Yoshio Mitarai, Takeshi Nagatome, Yosuke Tanaka

"This paper describes an application of lightweight soil in a deep water area to stabilize an existing quay wall at the Port of Tokyo. Super Geo Material, abbreviated SGM, is a type of lightweight soil, which consists of dredged cohesive soil, cement and air foam, and is applied in coastal development work, such as port and airport construction. This paper reports a SGM construction project at the Port of Tokyo by using a SGM special plant vessel, which was deployed for the Tokyo International Airport (TIA) Expansion Project in order to achieve large-scale and rapid construction. The key issue in SGM construction is quality control. One key quality issue is control of the mix proportion of SGM in consideration of volumetric changes due to air foam-breaking during pumping and air foam shrinkage due to water pressure when SGM is placed in deep water. A smart technique for placing SGM is also necessary to prevent quality deterioration when SGM is placed in deep water, for example, increased bulk density and decreased shear strength due to water absorption. This paper introduces an actual case of SGM construction with a particular focus on quality control of SGM during construction.INTRODUCTIONSuper Geo Material, abbreviated SGM, is a lightweight stabilized soil which is used in coastal development work in Japan (CDIT 2008). SGM is applied as a backfilling material behind existing quaywalls or above underground structures in order to reduce earth pressure on the existing structure and improve seismic resistance. SGM has been applied in many coastal development projects. In particular, SGM was used at the Tokyo International Airport (TIA) Expansion Project (Haneda Airport) as the backfilling material at a quay wall at the joint between the reclaimed area and pier part in a new runway (Nagatome et al. 2010a & 2010b, Yamatoya et al. 2010, Mitarai et al. 2011). In this project, large-scale and rapid SGM construction was implemented by the special SGM plant vessels within 6 months under the condition of limited construction period.This paper introduces a new SGM construction project at the Port of Tokyo in 2011. This project employed the special SGM plant vessel, “Ryujin Mark II”, to achieve large-scale and rapid construction within a limited period. SGM was also placed in a deep water zone at the maximum water depth of approximately 15 m. Thus, quality control of SGM was a key issue for meeting project requirements. This paper describes the actual SGM construction in the Tokyo Bay area and quality control techniques for SGM, considering volume changes due to pumping and placement below water."

Jan 1, 2015

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.IntroductionStone column ground improvement was implemented as a means of supporting mechanically stabilized wall approaches for a new bridge over the Puyallup River, part of HOV improvements to I-5 in Tacoma, Washington. The work discussed in this case history was part of the Washington State Department of Transportation (WSDOT) I-5/Portland Avenue to Port of Tacoma Road, Stage 1 Northbound HOV contract, developed as an early work element to a follow-on bridge construction project. The area requiring stone column ground improvement is shown in Figure 1. The improved ground supports permanent geosynthetic walls and embankments up to 50 feet high. This wall can be seen in Figure 1. The selected ground improvement primarily provides global stability of the soils beneath the walls during anticipated seismic loading and also reduces the time and magnitude of consolidation settlement under the weight of the planned embankment.Approximately 74,000 cubic yards of liquefiable alluvial soils were improved by stone columns. Stone column construction occurred in late 2010 and early 2011. This was followed by the embankment and wall construction. Settlement monitoring began with the embankment construction and continued into 2012."

Jan 1, 2017

By Victor Li, Joley Lam

"INTRODUCTIONJacked piles are piles that are pressed into the ground, usually by hydraulic jacks. For this reason, jacked piles are also known as pressed in piles. Jacked piles are mainly used for the following applications.• Underpinning worksJacked piles have been commonly used for strengthening the foundation of existing structures. In pressing the pile into the ground, the hydraulic jacks will jack against existing pile caps or ground beams that support the structure or against a steel frame connected to the floor slabs or structural walls of the structure. The self weight of the structure provides the reaction force for pile jacking. Jacked piles used for underpinning works usually have lower design ultimate capacities, typically less than 2000 kN (225 tons).• New foundationsJacked piles can be used to support new structures. A heavy pile jacking machine is employed to provide the reaction force for jacking the piles into the ground.• Retaining structuresJacked piles can be installed at close spacings to form a retaining wall. For relatively large and easily accessible sites, the piles can be installed using a conventional pile jacking machine. For sites that are smaller and are more difficult to access, a more compact patented equipment called the Silent-Piler developed by Giken Seisakusho Co. Ltd. in Japan can be used.Jacked piles have several distinct advantages. The vibration and noise induced during pile jacking are minimal. Jacked piles are 100 percent proof-tested to a load level equal to the maximum applied jacking force. The pile jacking machine can also be treated as mobile kentledge for static loading test. In this article, discussion will focus on jacked piles used for supporting new structures.HISTORICAL DEVELOPMENTThe People’s Republic of China (PRC) is perhaps one of the earliest countries in which jacked piles were used as new foundations. Jacked piles had been installed in the PRC since the 1960s. The capacities of jacked piling machines used in the country are usually in the range of 3000 to 6000kN (337 to 675 tons). High capacity jacking machines with a capacity of 9000 kN (1000 tons), presently used by the construction industry in Hong Kong, were also manufactured in the PRC. There are also plans to produce machines with a capacity exceeding 10000 kN (1125 tons). It was projected by Wang (1999) that jacked prestressed spun concrete piles would become one of the most popular pile types in the PRC in the 21st century."

Jan 1, 2004

By Remco Offenberg, Marcel Bielefeld, Martijn van Delft

The question of the continued suitability of existing foundations arises when the function of the superstructure changes. This can occur when the superstructure is replaced or when the existing structure is expanded, leading to higher loads on the existing foundation. Quite often it is a challenge to define the suitability (with respect to integrity, bearing capacity or both). The lack of information on the existing foundation (such as pile dimensions, installation records, original soil investigation, design calculations, etc.) makes it frequently seemingly impossible to assess whether the foundation or foundation elements can be re-used. The paper outlines the tools available to an engineer to evaluate existing foundation piles for potential re-use. The paper illustrates the application of these tools through a few case studies from The Netherlands, including the evaluation of a 400 years old bridge foundation to address increasing traffic loads.

May 1, 2022

By Andrew Z. Boeckelmann, David S. Graham, Paul J. Axtell

In the last fifteen years, several research studies have evaluated the ability to detect various types of deep foundation concrete integrity flaws with crosshole sonic logging (CSL) and thermal integrity profiling (TIP). This paper synthesizes the findings from the research, focusing on two studies that included CSL and TIP testing of drilled shafts with various types of flaws. The first, a 2016 research study of test shafts for the Wisconsin DOT, included inclusions inside and outside the reinforcing cage, intentional tremie withdrawal during concreting, and soft bottom flaws. The second, a 2021 study of production shafts for the Missouri DOT, included one shaft with and another without soft bottom conditions. After synthesizing the ability of each test method to detect each type of flaw, the paper presents recommendations for improving how CSL and TIP results are evaluated in practice. The recommendations highlight DFI‟s CSL interpretation protocol as well as the importance of evaluating TIP data versus time, not just depth. The paper includes example temperature-versus-time plots for various types of flaws and emphasizes how temperature-versus-time evaluation can be used to distinguish soft bottom conditions from standard bottom-of-shaft temperature roll off.

Oct 1, 2022

By Jason Herron, Joseph Brown

The common couplings for joining sections of helical piles with an outside diameter of 6.625 inches and 8.625 inches are square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. Each coupling type has advantages and disadvantages in efficiency, capacity, installation, and economics of the installed pile. All these coupling types have been used in the helical pile market in North America for various applications and designs. Many of these applications require on-site testing, but test records are not typically shared with the helical pile industry. Due to the lack of information available for square on square and flange to flange couplings, testing was done to compare the efficiency of installation, load to deflection response, and torque to capacity ratios of external pipe sleeve, square on square, and flange to flange couplings. Field installations and tension tests were performed in non-cohesive (sand type) soil near Caseyville, IL and in cohesive (clay type) soil in Centralia, MO. The data collected during these tests included rotations per foot during installation, installation torque, applied pressure, and deflection. The results of this testing are analyzed and discussed within this paper. The results indicate that the square to square coupling is the most efficient of the designs tested, but this conclusion cannot be fully justified without further testing due to the variability in the data gathered and the small number of piles tested. INTRODUCTION A helical pile is typically assumed to be a medium-displacement pile when its outside diameter is between 4.5 inches and 8 inches and a high-displacement pile when its outside diameter is greater than 8 inches. A helical pile designer has multiple options when selecting a coupling type for medium- to high-displacement helical piles. Each type of coupling has advantages and disadvantages and must be analyzed on the bases of efficiency, capacity, installation, and economics of a project. Typical couplings that are chosen by designers include square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. A helical pile must transfer axial, lateral, bending moment, and torsional loads, and the coupling must be designed to effectively and efficiently transfer each type of load. During the installation of a helical pile, the rate of penetration and the disturbance of soil layers play a critical role in the efficiency and torque to capacity ratio (Kt) of the pile. It is common for a coupling to protrude beyond the outside diameter of the pipe section being used. This is necessary for the function of certain coupling types and can facilitate the connection of couplings. However, it causes increased soil disturbance and reduce the rate of penetration due to soil bearing against the protruding portion of the coupling. A helical pile designer typically will work to minimize the coupling protrusion and create a pile with optimal installation efficiency but may choose a design with lower installation efficiency if it offers sufficient economic advantage.

Jan 1, 2019

By Alper Turan

The use of aggregate pier foundation systems has become widespread as the engineering practice moves towards cost-effective ground improvement solutions that provide accelerated construction schedules. Increased bearing capacity, effective settlement control and potential for liquefaction mitigation are commonly acknowledged benefits of aggregate piers. This paper studies the mechanisms by which aggregate piers interact with each other and with the surrounding ground when excited by seismic loads. A particular emphasis was placed on the response of a raft foundation supported on a site improved using aggregate piers. Three-dimensional nonlinear finite element analyses were conducted using commercial software package, ABAQUS. Non-linear soil behaviour is modelled using a three-dimensional total stress-based bounding surface plasticity model, which is able to simulate stiffness degradation and damping increase in the soil. The soil stratigraphy considered in this study was a 30 m deep soil deposit that comprised a very stiff base layer and a shallow soft surficial clay layer. Ricker Wavelet time histories with different frequency contents are used as the excitation force in the analyses. Various area replacement ratios (ARR) for aggregate piers are studied for a square plan layout. The results presented in this study are considered to be of interest to researchers and designers in evaluating the seismic ground response of the sites improved using aggregate piers.

By Charles Roeder, Amy Leland, Dawn E. Lehman

Concrete filled steel tubes (CFSTs) are composite members that are commonly used in many countries today. CFST components are used in the United States, but they are more common in Asia, in part because the connections used in Asia are quite labor intensive and there are not standard connections in the U.S. In addition, US design specifications are prepared by separate groups for structural steel and reinforced concrete structures and so composite systems that use CFST components are not overseen by a single group and as such there are several, conflicting design standards. In the US, steel tubes used for CFST are more slender (i.e., the diameter-to-thickness, D/t, ratio is larger) than some other countries, and labor practices (structural steel labor is different than reinforcing steel labor) also cause potential conflicts in construction. As a result, CFST has had some use in tall building construction in the US, but very limited use in bridge construction. A research program at the University of Washington has been in progress to address many of these issues with an eye towards universal design expressions, simpler, standardized connections and promotion of accelerated bridge construction (ABC). The research has resulted in recent changes to the American Association of State Highway Officials (AASHTO) bridge design specification as well as state departments of transportation (DOTs), which supports the increased use of CFST in bridge pile and drilled-shaft foundations. An experimental research study which investigate the flexural strength, shear strength and connections was conducted. These connections provide good performance under both seismic and gravity loads and address the concerns of US construction. These connections, their design rules and requirements, and their impact on composite behavior and system performance are discussed. These results permit rapid and economical construction of CFST bridge piers, piles and drilled shaft foundations. They encourage the use of more slender and economical tubes, while achieving the benefits of composite construction. INTRODUCTION Concrete filled steel tubes (CFSTs) are widely used for bridge and building construction in Asia, but the use of CFST in bridge construction is limited in the US. The historical use of structural steel and reinforced concrete in US bridge construction have resulted in more developed design expression for those construction methods, which has limited the use of CFST. Bridge construction in the US is inherently different than in Asia because of differences in codes, labor costs and construction practices. As a consequence, design and construction practices that are economical and practical in other countries may not be practical for US bridge construction.

Jan 1, 2019

By Stuart Hardy, Xiangbo Qiu

The South Bank Place project comprised the redevelopment of the iconic Shell Corporation headquarters in Waterloo, located on the Southbank of the River Thames in central London. The site was originally developed in the 1950’s and due to the monitoring of the underlying Bakerloo Line tunnels by the Building Research Station it has become a seminal case history for the long term swelling behaviour of London Clay. The redevelopment, undertaken by a joint venture of Canary Wharf Group and Qatari Diar, included demolition of the existing building (with the exception of the main towers) retention of the existing basement structure and the construction of eight new mixed use buildings, up to 31 storeys in height. The foundations for the new buildings varied according to the building height and the below ground constraints. Two of the buildings are partially founded in reused under reamed piles that were installed as part of the original 1950’s development. The paper describes the novel methodology developed to assess the re-use of the under reamed piles which builds on the guidance published by CIRIA and the BRE for straight shafted piles. The paper also describes the physical investigations and numerical analyses undertaken as part of the assurance process and the procurement of latent defect insurance by the client.

May 1, 2022

By Jin-Wei Huang, Bradley J. Fleming, Sri Sritharan

"Although soil improvement and its application to deep foundations is gaining popularity in the engineering community, this technique is not widely used in high seismic regions due to lack of fundamental understanding of both the behavior of improved soils under high-strain cyclic loading and the interactions between the pile, improved soil, and unimproved soil. This paper describes part of an ongoing Network for Earthquake Engineering Simulation (NEES) project, where two identical full-scale steel pipe piles were driven at a soft clay site in Oklahoma. The soil surrounding one of these piles was improved using the cement deep soil mixing technique in order to enhance its lateral load behavior. Both piles were tested for seismic resistance using dynamic and quasi-static loading.The pile in unimproved soil provided larger displacements with limited lateral force resistance. This pile was subjected to lateral displacements of up to 400 mm, but experienced minimum inelastic actions. On the other hand, the pile in improved soil reached its lateral capacity at a displacement of 100 mm, at which point the critical region at the base of the pile just above the improved ground experienced buckling and fractured due to low cycle fatigue. Compared to the pile in unimproved soil, the improved ground increased the system strength by 42%. Although the soil was improved over 2900 mm, the effective improvement depth was approximately 1300 mm below the ground surface.In this paper, it is demonstrated that the effects of block type soil improvement of limited horizontal and vertical dimensions can be described using a simplified theoretical approach involving a modification to the well-known p-y representation of soil response. An example using this method is presented and shown to give adequate support to a standard 12-inch diameter steel pipe pile embedded in soft soil,IntroductionPilings are the preferred foundation support for many civil engineering structures including highway bridges, railroad bridges, and port wharves. These structures and their foundations are subjected to forces created by earthquakes, wind, waves, water current, vessel impact, ice, and gravity. All loads applied to the superstructure must be transmitted to the foundation where they are resisted by the surrounding soil. With significant lateral loads, use of pile foundations may be the only solution to transmit large structural loads to competent soils. Piles supported by competent soils are relatively easy to design and costs are often attainable. However, thick layers of weak soils such as soft clays are widespread in high seismic areas (e.g., San Francisco, southern Nevada, Washington, Eastern Missouri, and Arkansas), exacerbating design challenges. Soft clays reduce the lateral resistance of the pile-soil system, making the pile foundation less cost effective. In this case, the current design practice is to use an increased number of larger diameter piles, which is a costly alternative (see SDC, Caltrans 2010). An innovative and more cost-efficient solution to this problem is to improve the soil within a short depth surrounding the foundation, thereby increasing its lateral stiffness. Some well-known methods for improving soil include deep soil mixing, stone columns, and simple soft soil replacement with select granular material."

Jan 1, 2017

By Joel Moskowitz, Jan Cermak

"New York City has unique geologic conditions which must be considered when designing pile foundations. Where shallow foundations are not feasible, the City's subsurface conditions require a variety of deep foundation systems, ranging from high capacity rock socketed piles, to piles end-bearing on bedrock, to friction piles bearing in alluvial or glacial deposits. Pile load testing is essential in confirming pile capacities as pile analyses include assumptions on soil and soil-pile response, and pile driving equipment. Load test results must be interpreted to estimate the long-term pile behavior. Except for lightly loaded driven piles, the New York City Building Code (the Code) requires that pile capacities be confirmed by static load testing. The Code provides the number of static load tests required, test procedures, and acceptance criteria. In the last few decades, methods other than static load testing have been developed including dynamic and rapid (pseudo-static) load tests. Recently, those methods have also been employed on several projects in New York City. The traditional approach to pile load testing in New York City is discussed herein including engineering involved in the analyses of test data with examples. In addition, several projects which included non-static load testing are discussed INTRODUCTIONPile load testing complements the subsurface information and pile design by providing further data on pile-soil interaction for the selected pile type and installation method. Traditional approaches to pile load testing in New York City involve static load tests to verify the design capacity of the piles for a given minimum factor of safety.In the late 1950's, Dr. Phillip C. Rutledge summarized his views on the philosophy of pile foundations in an unpublished, in-house document. He viewed pile foundations as good illustrations of pertinent and impertinent aspects of geotechnical engineering. In the analyses of piles he divided engineering into four general types:(a) Theoretical engineering in which decisions are made based on theoretical analyses. This represents ideal engineering, in which all factors affecting the pile design are well established or, at least, few simplifying assumptions with known effects on the analyses are made."

Jan 1, 2005

By S. E. Stallibrass, A. M. McNamara, J. P. Panchal, Leonardo M. LaLicata

Urban development in congested cities requires a better exploitation of the available surface, leading to taller structures. These buildings are usually founded on piles that have to be increased in dimension to accommodate the larger loads. Consequently, both the cost and the carbon footprint of the pile foundations rises. An alternative option is to improve pile performance by enhancing shaft capacity, which is commonly the most important factor in determining the ultimate capacity of a pile constructed in a clay soil subjected to axial load. For piles in stiff clays, such as London Clay, the soil/pile friction may be increased by profiling the side walls of a bored cast in situ pile with small discrete “impressions” such that the latter form nodules on the shaft of the concreted pile. The results from centrifuge and full scale field tests showed that the impression pile represents a viable technology to enhance the shaft capacity as they provide an increase in capacity of 40%. Alternatively, reduced length impression pile can be used. This paper explores the implications of the impression pile technology on the potential carbon saving.

May 1, 2022

By Partha Sircar

"For Berth 22 modifications at the Port of Oakland, nearly 600 octagonal 24-inch ‘diameter’ precast-prestressed concrete piles were driven, some piles over 160 feet long. Prior to production pile driving, an indicator/test pile program was performed, which included extensive use of dynamic load testing with (Pile Driving Analyzer (PDA) & CAPWAP analyses. The indicator test-pile program resulted in requiring significantly longer piles than the original design based on subsurface borings. The cause of this discrepancy is investigated in light of the available geotechnical information, soil mechanics principles and standard techniques for pile capacity computations. Several interesting phenomena emerged. These include relatively low resistances offered by crushed rockfill than would conventionally be assumed, non-homogeneity of an apparently uniform formation and the effects of jetting on pile side friction. Also revealing was the significant increase in capacity between 1 and 3 weeks of driving for long piles in clay. Recommendations were developed for pile capacity for future use as “lessons learned”.IntroductionThe foundation for the replaced Berth 22 structure at the Port of Oakland in California involved driving approximately 570, 24-inch octagonal precast prestressed concrete piles. A plan and a section for the pile locations are presented in Figure 1.The ultimate loads on the piles used in the design are presented in Table 1 – the loads are quite heavy.The foundation design was followed by an extensive Indicator Pile Program. The contractors (Manson Construction Co. of Richmond, California) opted to use a Delmag D62-02 diesel hammer (Rated Maximum Energy – 165 kip-feet). Per the project specifications, the same hammer was used for both indicator and production pile driving. The production piles of appropriate lengths were ordered based on thr results of the Indicator Pile Program. A number of interesting results were found from the Indicator Program, which is discussed in this paper."

Jan 1, 2015