Search Documents

By André Pomerleau, Michel Grégoire, René del Villar

"The operation of industrial flotation columns requires the control of at least two variables, the interface position and the bias rate, by manipulation of some appropriate operating variables. Problems arise due to the reliability of existing methods of measuring the bias (i.e bias = tailings water - feed water), a situation which has often forced the industry to disregard this control loop. Moreover, when using such a measuring approach, the identification of the process dynamics is impossible. A second problem arises from the possible interaction between both control loops that might call for the use of a more complex multivariable control strategy.Recent work done at Lava1 University has demonstrated the feasibility of an independent sensor for bias, which models the relation between the conductivity profile across the interface and the bias value using a neural network algorithm. A 250 cm height, 5.25 cm diameter Plexiglas laboratory column was equipped with a series of conductivity electrodes in its uppermost part (across the interface) to measure both interface position and bias rate. Using such equipment, the flotation column dynamics were identified. The results thus obtained permitted the design and implementation of a distributed PI control strategy, where bias was associated to wash water rate and froth depth to tails rate. Both PI controllers were tuned using a frequency-response tuning method. Results of both identification and process control are presented and discussed.INTRODUCTIONFlotation columns are used for the separation of valuable minerals from a carrier gangue. Typically, this device is a tall (9 to 14 m height) cylinder (1 to 3 m in diameter) although other cross sectional shapes are also used. Finely ground ore is fed as a pulp at about 2 m from the top of the column, and pressurized air is introduced through a sparger at the bottom. If the pulp has been properly conditioned with adequate chemical reagents (collectors and modifiers), the valuable mineral particles falling by gravity will attach themselves to the rising air bubbles, and the air-particle aggregates will rise to the top of the column where they overflow as a stream called the concentrate. The gangue particles,, that do not attach to the air bubbles, fall down the column being withdrawn at its bottom in a stream called the tails.A particular characteristic of flotation columns is the addition of a fine spray of water at the top. As the water flows down through the froth zone, it washes out the entrained gangue particles from the mineralized bubbles, thus improving the quality of the concentrate recovered at the top. As a result of its cleaning action, this water stream is called the wash water and the upper zone, the cleaning zone. In order to ensure a downward flow of wash water, a proper water balance must be kept in the froth zone, otherwise the water added at the top might shortcircuit to the concentrate without performing any cleaning action. This net downward flow of water inside the froth zone is called the bias and represents an important operating variable of a flotation column."

Jan 1, 1999

By S. K. Shaha, W. Kasprzak, D. L. Chen, J. Friedman, F. Czerwinski

The role of solutionizing conditions within the T6 heat treatment of the cast Al-Si-Cu-Mg alloy with micro-additions of Zr-Ti-V was assessed in terms of their influence on microstructure and mechanical properties. As a solution treatment, a single step process at 485 and 510oC and a two-step process at 510 and 525oC for varying time intervals from 0.5 to 9 h, were examined. In all cases, solution treatment was followed by isothermal aging at 150oC for 100 h. The microstructural analysis showed that the solution treatment changed the eutectic silicon morphology from needle-like, present after casting, to spherical shape in the T6 state and that the extent of changes was strongly influenced by temperature and time. The Cu- and Mg-rich phases completely dissolved during solution treatment while the Fe-containing phase, Al8Si6Mg3Fe, remained partially in the microstructure. The Ti, V and Zr containing phases, Al13Si2Ti3Zr and Al3Si26FeTiV10, present in as-cast state, were partially dissolved during solution treatment, reducing their size by 10 - 48%. The studied alloy reached the maximum ultimate tensile strength of 335 MPa and yield stress of 303 MPa for two-step solutionizing with a total time of 4.5 h. It is concluded that the two-step solution treatment resulted in higher tensile properties than the single-step process.

Jan 1, 2015

By Lachezar Tsotsorkov

Corporate social responsibility Is a principal trend of the corporate strategy for sustainable development of Assarel-Medet JSC ? the largest Bulgarian company for open pit mining and ore processing the production activities of which date back to 1964. Sustainable development Social responsibility is considered as one of the three pillars for sustainable development, together with the economic and environmental responsibility.

Aug 1, 2013

By J. R. Emery, D. F. Coates

"FOUR PAPERS ON CEMENTED BACKFILL were given at the Annual General Meeting of The Canadian Institute of Mining and Metallurgy in 1970:Weaver, W. S., and Luka, R., ""Laboratory Studies of Cement-Stabilized Mine Tailings"".Pasieka, A. R., Beattie, H. F., and Espley, G. H., ""Cemented Hydraulic Backill within the Falconbridge Group of Companies"".McLeod, P. C., and Schwartz, A., ""Consolidated Fill at Noranda Mines Limited (Geco Division)"".Clement, W. P., and Sokoloski, R., ""Pumping Cemented Backfill"".These four papers give the impression of a development in mining technology that has been substantially completed. Somewhat over ten years ago, The Inter-national Nickel Company of Canada, Limited and Falconbridge Nickel Mines Limited started experimenting with the addition of Portland cement to mill tailings to produce improved backfill and cheaper floors for scraping. Shortly after, the Canada Cement Company Limited (now Canada Cement Lafarge Ltd.), with full support of the two mining companies, started an extensive research program to provide the technologic-al data necessary to exploit what was obviously going to be a significant development in mining technology."

Jan 1, 1970

By Gregg S. Hill, Bert J. Huls

"This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed us to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flow sheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit. Details of the technology behind each unit operation will be presented in later publications.INTRODUCTIONSince 1996 BHPBilliton and MEL (Minera Escondida Ltda.) have developed a process to recover copper from coarse particles in the rougher tailings. Copper recovery from fresh tailings is not new. Several operations in Chile, such as Chuquicamata, El Teniente (AMEC, 2003), Mantos Blancos and others have operated various forms of tailings circuits. Both Chuquicamata and El Teniente practice cascade flotation scalping off froth containing fine copper particles after allowing sufficient retention time, air inducement and, sometimes, additional reagent addition. Chuquicamata tailings are not segregated but floated in sequential cascade and conventional large cell arrangements. At the Valle Central operation of El Teniente a coarse fraction of mill tailings is ground and floated, with the rejects recombined with fine tailings and subjected to cascade flotation through a sequence of concrete launders as the tailings flow towards their final deposition area. Mantos Blancos cyclone the rougher tailings and blend the underflow with scavenger concentrate from elsewhere in the principal circuit prior to flotation in Wemco Cells. Kemess in BC, Canada operates a 160 m3 Outokumpu cell to reduce the tailings sulfur content (Rasmussen, et.al, 2004)."

Jan 1, 2005

By M. Abzalov

"Control of analytical data quality is usually referred to in the mining industry as Quality Assurance and Quality Control (QAQC), and involves the monitoring of sample quality and quantification of analytical accuracy and precision. QAQC procedures normally involve using sample duplicates and specially prepared standards whose grade is known. Numerous case studies indicate that reliable control of sample precision is achieved by using approximately 5% to 10% of field duplicates and 3% to 5% of pulp duplicates. These duplicate samples should be prepared and analyzed in the primary laboratory.Bias in the analytical results can be identified by inclusion of 3% to 5% of the standard in each sample batch. Several different standards are used, with values spanning the practical range of grades in the actual samples. A blank (a sample in which the concentration of metal of interest is below detection limit) should also be included. Standard samples alone cannot identify biases introduced during sample preparation, and therefore approximately 5% of the duplicate samples (coarse rejects and pulp) should be processed and assayed at another, external, reputable laboratory.This paper discusses techniques used for estimation of errors in precision and accuracy, and overviews diagnostic tools. It is shown that one of the most commonly used methods, the Thompson-Howarth technique, produces consistently lower results than other methods. These results reflect the nature of this method, which relies on the assumption of a normally distributed error, and thus produces biased results when errors have a skewed distribution. This study concurs with the suggestion of Stanley and Lawie (2007: Exploration and Mining Geology, v. 16, p. 265-274) to use the average coefficient of variation (CVAVR(%)) as the universal measure of relative precision error in mine geology applications: Le contrôle de la qualité des données analytiques est habituellement désigné sous l’appellation d’Assurance et Contrôle de la Qualité (ACQ), elle implique le suivi de la qualité des échan¬tillons et la quantification de la reproductibilité et la précision analytiques. Les procédures des pro¬grammes d’ACQ impliquent habituellement l’usage de duplicata et de standards analytiques dont la teneur est connue. Plusieurs études de cas indiquent qu’une bonne fiabilité du contrôle de la précision des échantillons est atteinte par l’usage de 5% à 10% de doublons sur le terrain et de 3% à 5% de doublons de pulpe. Ces duplicata devraient être préparés et analysés au laboratoire principal.Un biais des résultats analytiques peut être identifié par l’inclusion de 3% à 5% d’échantillons standard dans chaque envoi d’échantillons. Plusieurs standards sont utilisés, avec des valeurs couvrant l’étendue des teneurs habituellement rencontrées dans des échantillons réels. Un blanc (un échantillon dans lequel la concentration d’un métal donné est sous la limite de détection) devrait aussi être inclus. L’emploi exclusif d’échantillons standards ne permet pas l’identification de biais résultant de la préparation des échantillons, de telle sorte qu’environ 5% des duplicata (rejets grossiers et pulpes) devrait être traités a un autre laboratoire indépendant et fiable.Cet article passe en revue les techniques utilisées pour évaluer l’erreur liée à la précision et a la reproductibilité, et effectue aussi un survol de divers outils diagnostiques. Il ressort de cet examen qu’une des techniques les plus fréquemment utilisées, la méthode Thompson-Howarth, fournit des estimés systémati¬quement inférieurs à ceux provenant des autres méthodes. Ces résultats sont un reflet de la nature de cette méthode, laquelle assume une distribution normale de l’erreur, biaisant ainsi les résultats lorsque l’erreur présente une distribution asymétrique. La présente étude recommande de privilégier l’usage du coefficient moyen de variation (CVAVR(%)) en tant que mesure universelle de la précision relative de l’erreu"

Jan 1, 2008

By Pierre Pelletier, Christian Pichetie, Dany Pelletier

"IntroductionDuring 1994, Barrick Gold Corporation, or American Barrick at that period, acquired Lac Minerals Ltd. properties. One of them was the Bousquet Complex. The Bousquet Complex is divided into three distinct sites: one mine (Bousquet 2), one mill (Est-Malartic Division) and one analytical chemistry laboratory (Les Terrains auriferes).The Bousquet 2 orebody was discovered in 1986. An extensive drilling program was initiated during 1987. Its purpose was to define the orebody extent. At the end of 1997, gold production from Bousquet 2 mine reached 1 290 000 oz of gold from a cumulative tonnage processed of 4 175 000 M t.From 1980 to 1990, the Est-Malartic mill was used for the treatment of ore from the following mines: Bousquet 1, Doyon, Francoeur (Richmont mines), Buckshot and 1-20 stope. At present, the mill receives ore from the Bousquet 2 mine.HistoryThe Est-Malartic mill is located close to the town of Malartic in northwestern Quebec. The mill has been in production since the mid-1930s processing mainly clean, free mill gold ore. Active mining from the Est-Malartic mine ceased in 1979 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that it would be economically more attractive to modify the existing Est-Malartic mill than building a new facility on site. The Est-Malartic mill modifications for processing the high-copper/gold ore from the Bousquet 2 mine began in late 1989 and new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leaching circuit continued to operate on the copper flotation tailings with some minor modifications to the solution handling systems. A S02/Air cyanide destruction circuit was also added at that time."

Jan 1, 2000

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama, Ryuji Oinuma

"Recently, the arsenic grade in copper ores has been increasing year by year. Arsenic bearing minerals (enargite (Cu3AsS4) and tennantite (Cu12As4S13)) coexist with typical copper minerals such as chalcopyrite (CuFeS2). The removal of arsenic from copper ores that contain relatively high arsenic content is essential due to its adverse impact on the environment and the resulting economic consequences. In this study, arsenic removal and dissolution behaviour of Cu and As from enargite (Cu3AsS4) were investigated using ferric sulphate (Fe2(SO4)3) solutions containing sodium chloride under high pressure oxidation conditions. The effects of numerous parameters including the concentration of Fe2(SO4)3 and NaCl, temperature, total pressure, leaching time and particle size were studied while other variables such as pulp density and stirring speed were fixed at 100 g/L and 750 rpm. The results showed that more than 60% of the copper was dissolved in a 0.1 M ferric sulphate solution under the high pressure oxidative conditions, whereas the leaching rate of arsenic was less than 20%. SEM observation revealed that elemental sulphur was deposited on the surface of enargite forming a passivation layer and the residue was agglomerated. Those phenomena may cause a decrease in the copper leaching rate. It was found that more than 80% of copper was dissolved in the ferric sulphate solution in the presence of 0.34 M sodium chloride under the conditions optimized, whereas the dissolution of arsenic in the mixture did not exceed 2%. XRD analysis of the solid residues from the leaching experiments used ferric sulphate and mixtures of ferric sulphate and sodium chloride showed arsenic to be present as scorodite (FeAsO4).INTRODUCTION In recent years, there has been an increase of the arsenic (As) content of copper ores due to the gradual depletion of high grade copper ores. In some copper deposits, arsenic occurs in the form of minerals such as enargite and tennantite. The removal of arsenic in ores containing copper is critical to the production of pure copper and the management of the environmental challenges caused by the smelting process. Due to the environmental risk caused by arsenic emission and the deteriorated quality of the copper product, smelting of enargite concentrates is not an effective method for the extraction of copper (Padilla et al., 2010; Safarzadeh et al., 2014; Long et al., 2012). Therefore, a number of studies have been carried out to develop arsenic removal technologies from copper ores using various methods such as hydrometallurgy (Curreli et al., 2009; Tongamp et al. 2010), pyrometallurgy (Dalewski., 1999; Padilla. et al, 2012) and bio-oxidation (Ehrlich, 1964; Sasaki et al., 2010). Several hydrometallurgical leaching processes like sulphuric acid, alkaline sodium sulphide and sodium sulphate and ferric sulphate leaching have been developed to treat enargite ores and concentrates. The alkaline sodium sulphide leaching process has been developed for the removal of arsenic from enargite (Anderson, & Twidwell, 2008; Parada et al., 2014). The mechanism of the dissolution of arsenic from enargite in sodium sulphite solution is"

Jan 1, 2016

By Fernando Canales

In the last decade a great dealt of attention has been paid to the chemistry of polynuclear gold derivatives with a central heteroatom, not only from the experimental and structural but also from the theoretical standpoint (1). Interesting hypercoordinated species of the type [C(AuPR3)5]+, [C(AuPR3)6]2+, [N(AuPR3)5]2+, [P(AuPR3)5]2+ and [P(AuPR3)6]3+ have been described (2), apart from other complexes with more conventional stoichiometry, and all have in common the presence of gold-gold interactions of ca. 3 Å. Usually, the chemistry of the first row elements of the p-block is known to follow classical rules of bonding, and only in cases of extreme electron-deficiency has the traditional electron count to be reconsidered to account for special types of molecular or solid state structures. Many of these heteroatomcentered complexes are electron-deficient and the gold-gold interactions provide a significant contribution to their stability. The attraction between these closed-shell systems has recently captured the attention in inorganic and organometallic chemistry (1). P. Pyykkö has summarized the available theoretical and experimental evidence of intra- and inter-molecular interactions between heavy metal atoms, such as Au(I) (3). In general, when heavy metals are involved in such interaction, the closed-shell attractions are of metallophilic or van der Waals type, as has been found for d8, d10 coinage-metals, and d10s2 centers. Experimental evidence for the aurophilic Au(I)???Au(I) attraction is available from crystallography, NMR and Raman spectroscopies, and optical spectroscopic measurements of the interaction strength (4). It is manifested in molecular conformations with relatively close Au???Au interactions of ca. 3 Å, whose strength has been estimated at ca. 25-50 kJ/mol (5). These attractions are weaker than most covalent or ionic bonds, but stronger than other van der Waals bonds and comparable in strength to typical hydrogen bonds. The phenomenon cannot be satisfactorily explained by classical theories such as hybridization (3). From a theoretical point of view, the attractions close to equilibrium distances are caused by dispersive interactions together with relativistic effects (6). The attractive contributions are dominated by pair-excitations from the heavy metal, such as gold, strengthened by relativistic effects. In all the cases where there are inter- or intramolecular metal-metal attractions, the correlation effects are essential; if they are omitted, at the Hartree-Fock (HF) level, repulsive interactions are obtained (6). Hence, it is necessary to use at least second-order Møller-Plesset level (MP2) methods for the dispersive forces, which are included in the electronic correlation effects (7).

Oct 1, 2003

Ontario Operaations Mining Garson Stobie Copper Cliff North Copper Cliff South Creighton Mcreedy East Milling Clarabelle Mill Smelting Smelter Matte Processing Anode Casting Refining Copper Cliff Nickel Refinery Port Colborne Cobalt Refinery

May 1, 2007

By Jean-Sébastien Kroll-Rabotin, Éric Climent, Florent Bourgeois

"Falcon concentrators are enhanced gravity separators designed for concentrating fine and ultrafine slurries. The Falcon UF model is unique in that it is dedicated to beneficiation of ultrafines, one key feature being that it does not make use of any fluidisation water. In a former study, we investigated the physical mechanisms that govern the transport of ultrafine particles (in the range 10 to 80 µm) inside Falcon UF concentrators, and concluded that separation efficiency is governed by differential settling. Initially, we derived and published a predictive model of the partition function under dilute conditions. The present paper proposes an extension of the initial model to concentrated ultrafine suspensions for application to industrial scenarios. The paper discusses how hindered settling has been added into the initial model to account for solid concentration effects. The modified model is tested against experiments carried out with a laboratory scale UF Falcon concentrator from dilute conditions up to 30 vol%. A good agreement between measurements and model predictions is obtained, which confirms that our hypotheses about the physics of separation inside a UF Falcon separator remain valid even at high concentrations.INTRODUCTIONThe Falcon concentrator is a fast spinning bowl that is fed at its centre of rotation. It uses centrifugal force to separate particles that are transported inside a thin liquid film that flows upward along the inclined wall of the bowl (McAlister and Armstrong, 1998). Due to differential settling, dense and coarse particles are concentrated inside the bowl whereas light and fine particles are rejected with the overflow stream. The fast rotation speed of the bowl yields high centrifugal force several hundred times the attraction of Earth. Despite the thinness of the liquid film (between 100 µm and 1 mm with a Falcon L40) where separation takes place, the Falcon concentrator can treat high flowrates (up to 30 L/min). At the bottom of the bowl, an impeller transmits the bowl rotation to the feed, which drains upward by centrifugal force as soon as it hits the base of the spinning bowl (Figure 1)."

Jan 1, 2011

By Michael Young, Josh Rubenstein, Michael Cooper, Tom Shouldice, Dan Curry

"Xstrata Nickel Australasia’s Cosmos plant in Western Australia is currently implementing a debottlenecking project to increase nickel output while maintaining metallurgical performance and a low unit cost for production. Mineralogical analyses indicated that the processing bottlenecks could be removed by simply reconfiguring portions of the circuit as well as adding capacity with technical advancements – notably an IsaMill™, Jameson Cell, Wemco® SmartCell™ and Larox Filter.The Wemco® SmartCell™, which is particularly suited for coarse mineral flotation, and Jameson Cell, which is particularly well suited for fast floating and fine minerals, combine as rougher scalpers to complete the main stream portion of the flotation circuit. Addition of the two new cells meet the required flotation capacity to handle the forecast increase in nickel feed grade and tonnage.The addition of an IsaMill™ for regrinding allows the SAG mill to produce a coarser primary product, thus enabling increased throughput. The advantages offered by the IsaMill™ include operation in open circuit (internal classification), an inert grinding environment (ceramic media) for better downstream flotation (“clean” new surfaces), compact footprint (easy to retrofit into existing plant) and energy efficiency. With the new rougher capacity addition, the remaining original plant cells were reconfigured to suit the new regrind mill and cleaning requirements. The existing 24 m2 Larox pressure filter was replaced with a larger 32 m2 unit to dewater the increased concentrate output.The paper describes the upgrade at the Cosmos concentrator with particular emphasis on the mineralogical data and metallurgical benefits associated with the changes.INTRODUCTIONThe Cosmos concentrator is located 680 km northeast of Perth in Western Australia. The deposit’s development and operations were started in 1999 by Jubilee Mines NL, Cosmos’ previous owner, with the first production of nickel concentrate in April 2000. The Cosmos concentrator treats a komatiite hosted high grade nickel sulphide ore, with sulphides being predominantly pentlandite and pyrrhotite with lesser amounts of pyrite and chalcopyrite."

Jan 1, 2010

By W. P. Tassie

"The location of Quintette Coal Limited's pit and geologic nature of the dedicated reserves combine to introduce a number of factors which can adversely affect waste dump stability. These factors include steep terrain, variable material type and particle size, and precipitation. This paper describes the solutions to related waste dump problems. A brief geotechnical review of the waste dumps is given and Quintette's operational strategies during periods of dump stability and instability are discussed. Despite best efforts, failures occasionally occur and discussion is included on Quintette's success at bringing failed dumps safely back into use. IntroductionQuintette Coal Limited (QCL) property is situated on the east slope of the Rocky Mountains near Tumbler Ridge, approximately 120 km southwest of Dawson Creek, British Columbia. This surface mine is located on mountainous terrain and is subject to climatic extremes of wind, precipitation and temperature.QCL has a current annual production of 4.75 million tonnes of metallurgical coal with a stripping ratio of 7: 1. This correctly implies the extraction of over 33 million bank cubic metres (BCM) of waste which is placed on numerous waste dumps at various locations adjacent to the pit.There are three active pits - Mesa, Wolverine, and Shikano (Fig. 1). Shikano is a newly developed pit located near the plant site. It is not subject to the unique dump management problems prevalent at the Mesa and Wolverine pits, therefore the Shikano waste dumps will not be discussed . The dumps for the Mesa and Wolverine pits, however, have been technically and operationally challenging since shortly after mining began in 1983. Their characteristics, associated site specifics and management, therefore, are the subject of this paper.Waste dump locations for the Mesa and Wolverine pits are shown in Figures 2 and 3 as is the relative waste distribution . Each sub-pit is connected to a principal waste dump in reasonable proximity and to an alternate dump should disposal of waste be necessary at that location. The waste dumps are constructed from the top elevations initially to coincide with subpit development. In the initial years (1-7) waste dump heights will be up to 250 m, then, as the mine matures (8-20 years), waste dump maximum heights will continuously decrease to coincide with lower bench elevations"

Jan 1, 1988

By S. Mostaghel, S. Nicol, M. Y. Solar

Once upon a time, the process engineer developing the design criteria for a new saprolite ferronickel smelter had it easy: most ores were around 2.5% Ni, with a Fe/Ni ratio of 4 to 5 and a SiO2/MgO ratio of about 1.6; to use the French word: garnierites. The ferronickel grade selected was the conventional 20 to 25% Ni and the impurity levels could be predicted from well established [C], [Cr] and [Si] vs (FeO) graphs. However the process engineer can no longer depend on statistics to design smelters: Ni grades are decreasing while the goethite contents are increasing; SiO2/MgO ratios vary from 1 to 3; and Al2O3 concentrations are reaching levels that cannot be ignored. Mechanistic models must be developed to select or predict essential parameters such as kiln and furnace reductions, ferronickel grade, slag losses, metal and slag liquidus, operating temperatures, etc. But these models must be simplified so that they can be used on a routine basis; and they must be calibrated against a wide range of commercial operations in order to yield the most realistic predictions possible. The present paper proposes one possible approach, using FactSage as a basic source of thermodynamic data. The predictions thus obtained are compared to actual performance for two well documented operations, as well as to the predictions made with other tools that might be more accessible.

Jan 1, 2014

By R. F. Hochstein, A. J. Neale, B. C. Flintoff

"Process control technology holds very significant potential benefits for many mineral and coal processing plants. The impact can be expected in terms of performance improvements (e.g. increased throughput, better quality control, higher availability), through reduced operating costs (e.g. lower reagent consumptions, manpower reductions) and in the form of intangibles (e.g. reduced vulnerability to manpower turnover, increased productivity in the user group). However, the installation of a process control system will represent considerable capital expenditure and will generate an operating cost. No management team would approve the funding for such a project without some reasonable measure(s) of the profitability of a proposed system. This paper describes a methodology for addressing the justification problem. Of particular interest is the approach to quantifying performance improvements, frequently found to be the predominant benefit of process control.INTROPUCTIONProcess control has become widely recognized as an essential component of any processing operation. It has direct impact on productivity, process efficiency and product marketability. The reported pay backs associated with successful installations underscore this observation. As a consequence, many operators who have little in the way of process automation are looking to initiate control projects, while those who currently enjoy some level of automation are looking to upgrade existing control systems (= process + instrumentation + hardware + software + operators + support). While the emphasis here would appear to be on retrofit process control projects, new plants, or those currently in the design stage, will usually find themselves in one of these categories shortly after startup 1."

Jan 1, 1990

By Benedetto Corain

The production and dispersion of metal nanoclusters onto inorganic supports and amorphous carbon rest on well consolidated technologies belonging to the realm of industrial catalysis and of basic catalysis research (1). In spite of the existence of a variety of specific synthetic strategies, their very rationale relies on three main approaches i. e.: A: precursors of both the metal nanoparticles and of the relevant supports (or the support itself) are intimately mixed (even let to react) at ambient conditions and then thermo-reduced according to very controlled protocols (2); B: precursors of metal nanoclusters are let to be adsorbed onto suitable supports from the gas or liquid phase and subsequently thermally decomposed (3); C: metastable size-controlled metal nanoclusters are previously generated in a liquid medium and subsequently transferred onto pre-formed support particles (4). The production and dispersion of metal nanoclusters onto organic soluble supports is also a rather well documented academic praxis (5, 6, 7, 8) able to provide e.g. size-controlled Au0 nanoclusters of 4.4±1.7 nm (5). Our group started in 1997 developing (9) an innovative approach to the synthesis of metal nanoclusters dispersed inside insoluble, albeit accessible (see below) mechanically robust gel-type resins (10), which procedure was tested so far on palladium metal. Metal ions are previously dispersed upon ion-exchange inside of the polymer framework, followed by chemical reduction and by the aggregation of born metal atoms into nanoclusters, the size of which is templated (11, 12) by the three-dimensional intercommunicating meshes that build up the overall polymer framework (Figure 1).

Oct 1, 2003

By H. Wotruba, J. Heizmann

"The use of shotcrete is a mandatory means for rock support and therefore for safety in many underground mining operations. If shotcrete gets into the flotation feed though, it can negatively influence the flotation process. This especially occurs when sublevel stoping, cut-and-fill or room-and-pillar methods are applied because as the mining face moves on, formerly applied shotcrete layers are mined together with the ore.As shotcrete does not differ significantly from fluorspar ore in its physical properties it gets moved through the comminution process and is fed to the flotation plant like the ore. To prove the influence of shotcrete on the flotation process, a laboratory test series was conducted at the Unit of Mineral Processing (AMR) of the RWTH Aachen University. The shotcrete grade of the flotation feed was varied between 0 and 10% through addition of pure shotcrete. Flotation parameters and also reagent dosage were held constant apart from the addition of the pH regulator, which was dosed to reach a constant pH of 8 at the flotation start. Results showed that with increasing shotcrete grades in the flotation feed the fluorspar recovery as well as general mass recovery decreased. The enrichment factor of Fluorspar also decreased with increasing shotcrete grades in the feed.In an effort to eliminate the shotcrete contamination of the flotation feed, a feasibility study for use of sensor-based sorting prior to the comminution process was conducted. Rock sorting not only reduces the bad influence of shotcrete on the flotation process, but also reduces comminution costs. INTRODUCTIONShotcrete is used in underground mining on a regular basis. It is used for rock support and therefore to increase safety in the underground mining environment. In mineral processing the presence of shotcrete can cause difficulties for example in the concentration processes. In flotation the highly sensitive reagent mixtures can be disturbed by the chemical activity of shotcrete and therefore recovery rates and selectivity of the process can suffer.Shotcrete is a special form of concrete which is applied pneumatically with high velocities and is compressed by its impact energy. Since the process is especially suitable for work in difficult environments and overhead areas, it is established in underground mining for many years. Shotcrete is not only applied in pre-processing of the mines, but particularly of use for cut and fill, as well as room and pillar mining methods. There it is used to secure excavation chambers. When the mine face is secured with shotcrete and subsequently the mining continues, the applied shotcrete will automatically be mixed with the ore."

Jan 1, 2016

By Norman O. Lotter, Lori Kormos, Greg J. Wilkie, Peter J. Whittaker, Johannes S. Stickling

"Assessment of opportunities to improve mineral processing performance in existing concentrators and in describing undeveloped orebodies is key to improving the business case of a mining company. This assessment has traditionally been performed using the distinct and separate inputs from Mineral Processing and Mineral Science.More recently, Process Mineralogy has been used to integrate these two disciplines. This trend has been driven by the need to develop and process more challenging ore deposits, and has been assisted by the availability of modern automated instruments. Together with the acquisition of a QemSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) from CSIRO in Australia, and with the use of a supporting SEM with EDX / WDX capabilities and an XRD, the development of Process Mineralogy at Falconbridge commenced in 1997.The sampling challenges in presenting a QemSCAN with representative sample material at the polished section level are significant, but have been effectively addressed. The full description of this aspect is beyond the scope of this paper.It is shown that, by use of this approach, the set nature of an orebody can be best exploited with selected flowsheet changes in a concentrator which address the generic characteristics of the orebody. In this way, the flowsheet provides a process that more effectively fits the mineral processing requirements of the ore. This leads to clear and tangible improvements in grade and recovery."

Jan 1, 2002

By M. Sharafodin, A. A. Hassanipak

Abstract - The essential aims of additional borehole drilling are to improve the reliability of grade and tonnage estimates in each reserve class and to increase ore tonnages. The "GET" function presented in this paper considers strategies for achieving both of these goals simultaneously, and therefore is advantageous for selecting sites for additional boreholes. The "GET" function is either a linear or a non-linear product of three variables G, E, and T: f(G,E,T,) = G??E??T??where the values of any or all of the exponents ?, ?, and ??may differ from unity at the discretion of the user. G and E are the average estimated block grade and the average estimation error for ore blocks in one vertical column, and T is the compounded ore thickness within the column. To illustrate its utility, the GET function has been used for determination of the most advantageous sites for additional drilling in the Shah-Kuh Pb-Zn deposit in west central Iran.

Jan 1, 2004

By M. Jahazi, J. Gholipour

Design and manufacturing of parts using hydroforming process require knowledge about material behaviour and tribological effects during hydroforming. Lubrication is one of the key issues in successfully hydroform the tubes. A Ni-based super alloy tube with 50.8 mm (2 inches) outer diameter and 0.9 mm (0.035 inches) thickness is considered for this research to study the effect of lubricants on the formability of the tubes. Hydroforming of a hollow compressor blade is considered for this project. A combination of press forming and hydroforming is employed to produce the part. LS-DYNA, an explicit dynamic finite element code, is used to model the experiments. Different lubricants are modeled using different coefficient of friction in the model. Predicted results for strain distribution at a critical section of the tube are extracted for each case to evaluate the effect of different lubricants on the process.

Jan 1, 2006