Search Documents

By I. Filzwieser, M. B. Hanel, A. Filzwieser

The paper describes the current density increase within the last 150 years. From the beginning in 1885 at 30 A/m² up to the highest used current densities nowadays at 420 A/m² towards future pathways were even 1000 A/m² can be achievable. A short tour through history will highlight the milestones of the process of electrolytic refining of copper. Besides the improvement of the existing technology, the biggest changes leading to higher possible current densities are linked to the introduction of the ISA stainless steel plates and the introduction of the parallel flow principle. Furthermore, the parameters influencing the limitations regarding current density and therefore the practical used current density as well as the influence from the chemical composition of the electrolyte is discussed. Finally, the possibility of further increasing the current densities by enhancing the relative movement between electrolyte and electrode will give an outlook about the future of the copper electrolysis process. INTRODUCTION The current density is the most important characteristic to describe the productivity of a copper refining electrolysis besides the characteristic number for the electrical efficiency. Over the last 150 years, current density has risen from a few amperes per square meter to over 400 A/m² without any significant change in the principle of electrolytic refining. This increase in current density is documented exemplary by the electrolysis of Montanwerke Brixlegg in Austria (Brixlegg, 1963, 2013). The very beginning of the technology of electrolytic refining of copper was first patented in England by James Elkington in 1865 and the first electrolytic copper refinery was built in Newark, New Jersey, in 1883 (Armstrong, 1999). The secondary smelter Montanwerke Brixlegg, Austria, has been operating an electrolysis plant since 1884. In 1988, the third "Mount Isa" electrolysis plant worldwide and the first in Europe was put into operation in Brixlegg. Since 2010, the so-called high-current electrolysis (parallel flow METTOP-BRX Technology) with a current density of approx. 400 A/m² has been operated in half of the electrolysis process.

Jan 1, 2019

"This paper deals with the reconciliation of open stope performance at Olympic Dam, South Australia, with a focus on stope stability, recovery, and operational aspects of stope reconciliation in relation to the expected or planned stope design. The observed stope performance is inconsistent with the equivalent linear overbreak sloughing criteria for assessing the performance of large open stopes. The aim is to investigate new stope performance criteria using quantitative (overbreak, underbreak, maximum depth of wall failure) and qualitative (stope productivity, observed fragmentation) information that correlates with the observed stope behaviour, providing a process for improving future stope designs.RÉSUMÉ Le présent article traite de la réconciliation de la performance des chambres ouvertes à Olympic Dam, Australie du Sud, en ciblant la stabilité des chambres, la récupération et les aspects opérationnels de la réconciliation des chambres par rapport à la conception attendue ou planifiée des chambres. La performance observée des chambres ne concorde pas avec les critères d’épaisseur équivalente du bris hors profil pour évaluer la performance de grandes chambres ouvertes. L’objectif est d’étudier de nouveaux critères de performance des chambres au moyen de données quantitatives (rupture hors profil, rupture à l’intérieur du profil planifié, profondeur maximale d’effondrement du mur) et qualitatives (productivité de la chambre, fragmentation observée) qui concordent avec le comportement observé des chambres, fournissant ainsi un processus pour améliorer les futures conceptions des chambres."

Jan 1, 2015

By K. Reinharter, J. Schmidl, D. Gregurek, A. Spanring

Copper smelting furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear. This paper evaluates the common refractory wear mechanisms as observed in the copper Peirce-Smith converter and in the copper anode furnace. The chemical factors include corrosion caused by fayalite type slag and sulfur supply, as well as, by Cu-oxide attack. Changes in the temperature during the furnace operation (thermal-shock) create stresses in the brick lining which can only be absorbed in limited extent. Mechanical factors include erosion, caused primarily by the movement of the metal bath, slag and charging material, as well as, stresses in the brickwork due to punching. Finally improper lining procedures can also effect the service life. All these wear parameters lead to severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” together with thermochemical calculations by FactSageTM software is an important prerequisite for the refractory producer. Based on these research results, combined with specific process knowledge, appropriate brick lining solutions for copper processing furnaces can be recommended. INTRODUCTION The refining of copper includes converting of matte or black copper into blister copper for final fire refining process in the anode section. Typically Peirce-Smith (PS) converters are in use. Other technologies include Hoboken Converter, TBRC but also Flash Converting Furnace and bath smelting furnaces (ISA, Ausmelt) (Davenport et al., 2002). For fire refining two types of furnaces are used – the rotary furnace type is dominantly used in the primary production route while secondary smelters tend to use hearth refining furnaces which are more suitable for scrap melting. Installed working linings are based on magnesia-chromite bricks but especially in the anode refining section the application of alumina-chromia bricks have become more popular in the recent years. It comes without saying that, to some extent, large variations in the slag composition can be observed from the data provided to RHI Magnesita during post-mortem studies of used refractory samples and this needs to be addressed properly during the selection process of refractory linings.77

Jan 1, 2019

Spatial information Critical to a project since it underpins: ?Discovery of mineral resources ?Orebodydefinition and technical assessment ?Mine design and planning ?Profitability and project value Data ?Single most import asset. ?Good interpretation of quality data underpins project growth and success. TEAMWORK

May 1, 2002

By Marc Bétournay

This article examines how fuel cell technology and related power distribution system fits within mine operating requirements. Considerations for improvement of power plant architecture and functions to yield production advantages are presented. Improvements to conventional mining approaches are also discussed.

May 1, 2007

By F. N. Smith

Corrosion was observed on the aluminum pressure plates and dress-caps that hold the glazing in place on a curtain-walled building, The multi-storey building in question is situated in the downtown area of a busy Canadian city, For aesthetic reasons, the original design required the dress-caps (which have L-shaped cross-sections) to be externally clad with thin copper sheet. Since the aluminum was in direct contact with the copper trim, galvanic corrosion developed that resulted in damage to the aluminum components, Soluble corrosion products washing off the copper trim may also have contributed to the accelerated corrosion of the aluminum, The aluminum pressure plates and dress-caps are being systematically replaced with components made of fibre-reinforced plastic. The outsides of these new components will be clad with thin copper sheet in order to preserve the original appearance of the building.

Jan 1, 2005

By W. Lamb

Feed Preparation ? Five primary parameters affect the screening efficiency ? Ore characteristics ? Operational characteristics ? Screen characteristics ? Water addition and washing ? System design

Apr 1, 2005

By Craig Haase

A. Introduction

Jan 1, 2003

By Georgia J. Lysay

Kemess South Mine ended operations in March 2011. Final reclamation works began during operations in 2008 in anticipation of closure. The focus of reclamation during mine operations was on the inactive areas of the tailings dam, waste rock dumps, and expended borrow areas. The general reclamation strategy for the Kemess Mine site marries long-term erosion control with successional reclamation principles. For disturbed areas, this requires application of growth media, proper preparation of surfaces, and introduction of native pioneer plant species to initiate successional processes of recovery. Tailings are retained behind an earthfill dam of approximately 140 m in height, with a crest length in excess of 1 km. Reclamation activities at the dam have included placement of growth media, specialized surface preparation and construction of diversion ditches. The final closure spillway is currently being constructed, with completion scheduled for summer 2011. The two main waste rock dumps contain segregated non-acid generating (NAG) waste rock and potentially acid generating (PAG) waste rock. Resloping of the NAG dump for long-term stability commenced in 2009, followed by placement of growth media and ground preparation. The PAG waste rock will be fully relocated into the expended open pit for final, permanent subaqueous disposal.

May 1, 2011

By A. West, F. Mohammadi

Growing awareness of selenium bioaccumulation has resulted in selenium management becoming an important environmental issue for mining operations. Selen-IX™ is a novel ion exchange based technology developed by BioteQ to provide an effective solution for removing selenium oxyanions from mine impacted water to single-digit µg/L levels. The technology offers significant potential benefits when compared to incumbent biological treatment processes, including substantially reduced capital and operating costs and significantly reduced production of a selenium-containing sludge for final disposal. This paper reviews the key features of the Selen-IX™ process and presents the results of recent pilot testing on selenium impacted water.

Jan 1, 2014

By Les F. Sawatsky

Surface drainage, particularly mine closure drainage, must be properly considered during all stages of mine planning because it presents constraints that are critical to economic mine operation, minimizing environmental impacts and ensuring compliance with government regulations. Deficient mine site drainage increases costs of operation, causes unnecessary environmental impacts and may result in regulatory violations. The scope of this paper includes stream diversions around mine areas, drainage systems within the mine disturbed footprint, and closure drainage works to control surface water, ground water, erosion, sedimentation, and seepage discharges following mine operations. Developing selfsustaining drainage facilities upon mine closure, requires a mine plan that develops appropriate topography and constructed drainage courses that replace the function of pre-disturbance drainage systems without aggravated erosion and deterioration. Drainage criteria, particularly closure drainage criteria, represent important constraints on mine planning and are best considered by integrating drainage features into the mine plan well in advance of mining activities. Integrated mine planning by a multi-disciplinary team is recommended to achieve closure objectives at minimum cost and maximum effectiveness The geomorphic approach to channel design is an effective means of providing a drainage system that has the appearance, function and longevity of natural systems. By incorporating this technique into closure drainage planning, mine operators can construct sustainable (walk-away) drainage systems that require little or no maintenance in the long-term. This paper presents a process by which drainage criteria and associated mine plan constraints can be integrated into the mine planning process. This paper outlines the process for detailed design of drainage facilities, particularly closure drainage systems that are designed by the geomorphic approach.

May 1, 2009

By J. Baumbach, H. Bombach, M. Stelter

"Today technical electro-refining processes for copper exclusively use sulfuric acid, for silver refining nitric acid electrolytes are used. Sulfuric acid is characterized by very good chemical and electrochemical stability, good conductivity and low cost. The disadvantages of sulfuric acid are the precipitation of fine-grained cathodes with smooth surfaces only by using additives like glue, thiourea and chloride. In case of silver the electrolyte is electrochemical unstable and bears the risk of the formation of toxic NOx when pH is too low. A second disadvantage is the form of electrodeposition of silver as dendrites with their removal from the bottom of the Möbius cells.This paper reports the results concerning the application of an alternative electrolyte in copper and silver electro-refining. At first the electrolyte was characterized by the determination of current density potential curves. Electrolysis experiments were performed in laboratory scale using technical anodes for copper and synthetic anodes for silver. During the copper tests the solubility of contaminations from the anodes and the amount and chemical composition of the anode slimes were determined. Moreover the influence of current density, electrolyte temperature and the effect of several additives on the precipitation and chemical purity of the cathodes were investigated. In all experiments cell voltage as well as anodic and cathodic polarization was measured and current efficiency and specific energy consumption were calculated. A comparison with the results with those of tests using conventional sulfuric acid electrolyte shows the advantages and disadvantages of both systems, additionally the technical application chances and limitations for the new electrolyte. This electrolyte enables the precipitation of smooth copper cathodes with low silver and sulfur concentrations even at lower temperatures without any additive. For silver refining the electrodeposition of compact silver sheets is possible, that can be stripped comparable to those in copper electro-refining."

Jan 1, 2016

By Fulchand Shende

Around the world many potash mines experience brine inflow problems. The presence of brine in underground excavations may induce structural and stability problems. A study has been carried out to simulate the effect of brine on the performance of pillar support. The testing program consisted of loading potash specimens in a creep frame, and simulating inflows by continuously pumping brine into an experimental cell. Brine temperatures and load conditions were varied to simulate several mining and inflow conditions. Specimens were fitted with acoustic emission transducers to monitor energy emissions during an eight-hour test duration. Samples of brine were also collected to provide K+ and Na+ concentration data necessary for an accurate assessment of the dissolution process. Test results indicated that dissolution rates are highly dependent on brine temperature and load conditions. Loads approaching 50% UCS tend to generate very high rates of energy emissions, often leading to the failure of the simulated pillars. This study demonstrated that acoustic emission could be effectively used for predicting the performance of pillars when exposed to inflow brine.

May 1, 2001

By Marcel Laflamme

Underground mine workers are continuously exposed to many sources of noise and vibration in carrying out their tasks. Even though the vibration and sound level of some mining equipment is documented, it was found that this information is not readily available for many pieces of equipment and that it is not considered when choosing equipment or planning tasks. As well, health problems related to vibration and noise are among the main causes of work-related compensations in mines. Considering those facts and although no Canadian regulations could force employers to limit the exposure of their workers to vibration, the Société de recherche et développement minier (SOREDEM) decided to address the problem by including vibration among their research priorities. In order to characterize noise and vibration sources of different mining equipment used for underground mining, the authors have performed a study in 8 different mines in Québec on 28 different mining equipments. The paper will present the procedure that was followed to select the list of equipment to be evaluated and the low cost acquisition system developed to perform multichannel time domain acquisition in harsh environments. It will also present the results obtained for the noise level produced by the equipment as well as for the hand-arm and whole-body vibration exposures.

Aug 1, 2013

By Kimberly M. Curran

The path by which hydrogen supply is provided to any end use application will have a strong effect on the specific economics and price stability for the product supply and the flexibility with which it can be used. The objective of this paper is to present those variables which play a significant role in the selection of the hydrogen production technology, with a particular focus on several typical mining applications. The variables examined include gas requirements in terms of flow-rate and demand profile, overall volumetric consumption, level of interruption tolerable, gas pressure and quality needs. Also examined are the effects of geography in terms of primary energy supply available as well as existing hydrogen sources, developed or not. The role of these factors in the selection of an appropriate supply chain capable of supporting mining applications that use hydrogen as an energy carrier will be illustrated with a typical mining application scenario drawn upon in the form of a case study.

May 1, 2007

By Simon C. Dominy, Alwyn E. Annels, Mark A. Noppé

Abstract - Mineral Resources and their subsequent conversion to Ore Reserves are of key importance to mining companies. Their reliable estimation is critical to both the confidence in a feasibility study, and also to the day-to-day operation of a mine. Together with sampling, assaying, geological and other errors introduced during interpretation and estimation, additional errors are likely to be introduced during the application of technical and economic parameters used for conversion of resources to reserves. There is thus a requirement for high-quality interpretation and estimation to be supported by high-quality data. Any company expecting to make sound investment or operational decisions must base this on both relevant and reliable information. An Ore Reserve statement generally contains a single set of grade and tonnage figures without a discussion of the potential inherent errors in these estimates. Some sensitivity studies may be run, but confidence limits are rarely quoted and, if they are, often do not take into account many of the factors that cause uncertainty in the grade and tonnage estimates. Mineral Resource and Ore Reserve estimates thus carry certain errors leading to uncertainty and risk; some of these are unquantifiable for various reasons, for which the operator should be aware. This paper presents a review of the potential sources of error that might occur during a resource estimation program, which are carried through into the reserve estimate. A number of methods are discussed that allow the estimator to be more transparent about the inherent risks in his/her estimate. Emphasis is placed on data quality, and the requirement for strong quality management to be linked to continuous improvement.

Jan 1, 2002

By Alim Ullah

Danieli entered into the Direct Reduction (DR) field in order to offer its clients complete turnkey facilities for steelmaking?from processing of raw materials through finished products. The Danarex® Process produces a passivated product, called the Supermetallic (SPM), without hot-briquetting. One of the main features of the Danarex® Process is its ability to produce approximately 50% of the Direct Reduced Iron (DRI) through reduction gas generated in a reformer and another 50% through recycling preheated furnace exit gas. Some other distinguishing features are: separation of carburising and cooling zones and the use of double bustle for better distribution of gas inside the shaft furnace. A pilot plant was set up at Hazen Research, Inc., Golden, CO in order to show that the integrated process works as expected and to obtain process data. The SPM obtained was of a very high quality, evidenced by metallization levels of 92% to 98%. The carbon content could be controlled between 1.5% to 4.0% by varying the operating conditions and approximately 75% of this carbon was present as Fe3C. The product was tested for inertness by Chilworth Technology, England, using UN standard tests and was found to be safe for outdoor storage and transportation.

May 1, 2003

By A. J. Basu

Air quality in underground mining operations can fluctuate significantly during the working day, but until recently the only way to ensure a mine had sufficient air quality was to over-ventilate and, with significant delay in adjusting the volume or direction of the airflow, working conditions were tolerable but rarely ideal. Underground ventilation management systems have been considered to achieve improved energy efficiency since at least 1995 in Canada. However, Mine Ventilation Optimization, (MVO) and integrating it with Ventilation on Demand (VOD) is only becoming more of a reality in the last seven (7) years. A systems approach to MVO takes into account all the elements from the point the power is distributed into the ventilation fans through to the actual quality and quantity of fresh air to the working face. Opportunities exist throughout the system for energy savings but not all of them are cost-effective. Depending on the application, these opportunities can be easily realized by properly sizing, streamlining, maintaining and operating the ventilation system using premium mine proven energy efficient components throughout. Implementation of VOD is a key step in achieving the MVO objective. However, VOD is a concept, and it requires various tools, procedures, and strategies for cost-effective and operationally viable implementations. This paper provides a historical background in the development of VOD and provides a framework for proper and cost effective implementation. In addition, an optimized ventilation system will also allow increased airflow by reducing resistances and shock losses. This turn in would allow production target improvement, which could be an attractive objective compared to energy savings. Mine ventilation is the life support system of an underground mine, and contributes to sustainable development and corporate social responsibility goals assuring health and safety aspects of strategic planning. The proposed framework addresses implementing mine ventilation optimization integrating ventilation on demand as a vehicle for energy, health and safety improvement and overall productivity gains in the mining cycle efficiency while significantly reducing carbon footprint of a mine.

Aug 1, 2013

By Prodipto Ghosh

This paper is prepared as a review of existing and traditional methods related to electrical maintenance strategy. Its primary focus is to explore newer ideas and how they point the way to a more efficient and effective manner of electrical maintenance. This discussion is primarily related to large electrical distribution assets typical of heavy industry such as mining.

Aug 1, 2013

By J. A. H. Church

MR. J. A. H. CHURCH: The salient feature would seem to be that the thickness of the seam, in our coals at any rate, is the main factor in predisposition to spontaneous ignition. The evidence, incomplete it must be admitted, in the Saskatchewan and British Columbia fields, and complete in the Alberta field to my mind, shows this up very strongly. The German report on the upper Silesian coal fields definitely fixes the critical thickness at 13 feet, the British report goes far beyond this figure by stating that liability to ignition increases with the thickness of the seam over four feet. Before discussing the Alberta fires it would be well to note an error on page 12 -the probable cause of the fire in the Frank Mine should read "Spontaneous near fault. Heating first discovered 1909". Of the six fires attributed to spontaneous ignition all the seams were identical or in excess of the critical thickness mentioned in the German report. If there be any reason in the foregoing it is high time some forethought were taken to adopt some definite system of laying out the workings of such seams not so much on the outcrop districts as with a view to the future operation to the dip. Seams approaching 13 feet in thickness which to date have shown no disposition towards heating during the extraction of the outcrop areas may well cause infinite trouble or indeed total loss when the ventilating pressures increase as increase they must to the dip. This state of affairs can be combatted only by the adoption of a correct system of working and the provision of numerous airways of as large an area as may be compatible with the physical characteristics of the particular seam.

Jan 1, 1923