Search Documents

By R. D. H. Wigmore

"The title of this paper probably sounds quite simple and self-explanatory. The problem, however, was not a simple one, and proved somewhat baffling and expensive over a period of years. After outlining the problem, and the methods which were used to overcome it, we will present our solution, or perhaps it would be more accurate to say the partial solution which we reached.We have in the cyanide circuit at Upper Canada two Dorr Single Tray Thickeners with 30 ft. diameter wood stave tanks 12 ft 4 1/ 2 in. deep. In the years prior to 1948, when the tonnage was 250 to 280 tons per day, two stage thickening was practised. As the tonnage was increased to 450, 500, and finally 560-600 the thickeners were used in parallel.Some settling problems were encountered, and in those days the means to combat these problems were very few. The only remedy was to dump in pounds and pounds of lime. Then along came a few reagents, and the writer remembers one in particular, - 11 Carboxel11 (carboxymethlycellulose). When water or solution was added to this reagent, the result was a gooey mass somewhat resembling tapioca. One drawback was that it stayed in this state, and didn't go anywhere. A method was finally developed of containing the mass (or mess) on a fine screen, and dissolving some of it was a fine spray of solution. The only thing the writer recalls was that it was not a very effective settling agent.Shortly after this time, along came the new flocculents, first a few, and then many, and our settling problems were over.But when the settling problem was solved at Upper Canada, some other problems were creeping up on us."

Jan 1, 1965

By O. A. Ojo, R. G. Ding, M. C. Chaturvedi

In this study, the fusion zone microstructure of tungsten inert gas weld of a directionally solidified NhAl-base alloy was examined by the standard metallographic techniques involving the use of optical, analytical scanning and transmission electron microscopes equipped with energy dispersive spectrometer. Fusion zone cracking was observed to be closely associated with interdendritic secondary solidification microconstituents identified as consisting of y, y' and NiMo (Y) phases. Depression of solidification temperature to the terminal ternary eutectic reaction temperature of the system during cooling is suggested as an important factor contributing to the fusion zone cracking.

Jan 1, 2006

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By F. R. Ploeger, J. H. Crocket

"IntroductionRocks in the Kirkland Lake district form part of the Timiskaming Group, a south-facing homoclinal sequence of wackes, conglomerate, trachytic flows and pyroclastic rocks and syenitic intrusive rocks. Hewitt (1963) indicates that the thickest section, about 5 km, of the Timiskaming Group rocks is attained in Lebel Township. Several writers (Thomson, 1948; Hewitt, 1963; Hyde, 1978; Jensen, 1978; and Downes, 1979) have observed that the Timiskaming Group unconformably overlies the Keewatin volcanics, particularly along the northern contact. Recent work by Downes (1979) in McGarry and McVittie townships to the east of Kirkland Lake has shown that much of what had formerly been classified as Timiskaming actually belongs to an older group of rocks, the Larder Lake Group (Jensen 1978).General GeologyA series of fluviatile, braided-stream sedimentary rocks (Hyde, 1978) form the oldest of the three major rock suites at Kirkland Lake. Conglomerates constitute a large proportion of these sedimentary rocks and typically contain a large percentage of a variety of locally derived alkalic rock clasts as well as the distinctive red jasper iron-formation pebbles (Fig. 1a). The associated wacke units can be massive to finely bedded and are interbedded with the conglomerate. They also contain a large alkalic tuffaceous component.Interbedded with these sedimentary rocks are alkalic extrusive rocks, including tuffs, agglomerates, breccias and flows, which represent episodes of fissure and explosive crater eruption (Cooke and Moorhouse, 1969). The tuffs, although dominantly alkalic in composition, are commonly reworked and contain sedimentary features such as graded bedding, scouring and crossbedding (Fig. 1 b). The trachytic flows are massive to porphyritic and outcrop mainly east of Kirkland Lake in the adjoining townships. Altered leucitic porphyritic flows, locally referred to as red and green spotted trachytes, commonly occur."

Jan 1, 1982

By R. C. Reed, L. T. Wu, H. C. Harada, K. Kawagish, R. T. Wu

Oxidation of pure metals is a chemical reaction in which the metal loses one or more electrons, such that the atom of the metal changes from the neutral state to a positively charge ion and reacts with oxygen to form an oxide of the metal. The oxide can form as a protective and adherent scale that slows down further oxidation, or may spall off repeatedly, exposing fresh metal surface to react with oxygen. In multi-component alloy systems such as typical high temperature NiCrAlY bond coats, more than one oxidation mechanism may take place at once and thus, complicates the study of oxidation. To better understand the competition between formations of oxides of different compositions, a thermodynamic assessment is carried out to study the oxidation mechanism of a Ni-27Cr-9Al (at %) ternary alloy. Based on the assessment, it is demonstrated that the layering of different oxides can be determined, with the most stable oxide (alumina) existing directly above the metal-oxide interface and the least stable oxide (nickel oxide) locating on the outer most layer. A comparison between the calculated results and previously published experimental observations shows excellent agreement.

Jan 1, 2010

By Douglas Lay

Attention has been drawn in the publications of the Department of Mines to the view that veins of two different ages occur in the Cariboo district, namely, those of Jura-Cretaceous age and those of pre" Mississippian age. It has been further pointed out that while there is doubtless a wide distribution of veins of pre-Mississippian age in and about the Barkerville and Stanley areas, and in the vicinity of Round Top mountain and Yank's peak, there is no such wide distribution of veins carrying gold values of commercial significance. Veins of the latter type discovered to date occur almost exclusively within one or other of two comparatively narrow zones, both trending northwest and southeast, the one extending from Island mountain co Round Top mountain, and the other from a point somewhat north of Stanley co Yank's peak. In addition, there is some evidence of a third zone trending northwest from Spanish mountain, at or near the contact of the pre-Cambrian and Mesozoic rocks. In short, all the evidence from prospecting and lode-mining operations to date indicates that values are mainly restricted co zones having marked directional distribution. Moreover, it can be demonstrated that the placer deposits resulting from the erosion of the pre-Mississippian veins have a similar directional distribution, allowance being made for modifications due to glaciation. The observations offered in this paper are of the nature of a generalization which seeks to explain certain anomalies both in the vein-mineralization and in the -important auriferous-pyrite replacement deposits in limestone which have recently been discovered. For the sake of brevity, the Island Mountain-Round Top Mountain zone will be referred to as Zone No. 1, and the Stanley-Yank's Peak zone as Zone No. 2.

Jan 1, 1936

By A. Gillis, J. Keyes

"This is a prelirr1inary report on automatic control at East Malartic Gold Mines.After installation of the cyclones in the East Malartic grinding circuit, the interest was aroused in the automatic control system for the circuit. Investigations were made as to the possibilities of such an installation. This resulted in a preliminary survey of the circuit by Milltronics Ltd and an analysis of the circuit by Mines Branch personnel. A study of the investigation and analysis indicated that a cost reduction and improved efficiency could be expected by the installation of an automatic control system in the grinding circuit. It was also indicated tl1at such installation should pay for itself within a year. This was the point that sold management on such installation. The need of three operators was expected to be eliminated .The installation was to consist of a central control panel, microphoncs on each mill, regulation of feed rate, pneumatic valves for addition of solt1tions, density control of the cyclone overflow, which is a grinding circuit product, rod mill feed box plugging detector and a conveyer weightometer for tonnage indication and control.As well as the elimination of one man per sl1ift, other benefits which were to be received but unable to estimate were: 1) More tonnage per clay by operation of the mills at the proper capacities. 2) Lower grinding costs. Less under-loading should result in less steel wear and lower pumping cost. In the condition of overloading, a coarser grind is obtained resulting in greater impeller and liner wear. The overloading and underloading showed up on the n1icropl1oncs. 3) An improvement in the recovery as a result of less over-load. The tailings loss from a coarser grind are not as frequent."

Jan 1, 1965

By BARRY BANNATYNE

Gypsum in Manitoba is quarried from the Jurassic Amaranth Formation a1 Gypsumville and Harcus; it has been mined near Amaranth and Silver Plains. At Gypsumville, gypsum is carbonate- free but has thin clay laminae between gypsum layers; the rock is folded in places, and some anhydrite is present. At Harcus, gypsum contains scattered dolomite, both as patches in a penemosaic pattern and as thin layers; small chalcedonic concretions also can be found. The quarry at Harcus was opened late in 1978 and currently produces about 100,000 tonnes annually. The two inactive mines near Amaranth operated from 1932 lo 1963 and from 1967 to 1970, and contain a central anhydrite layer. The mine near Silver Plains was flooded from an underlying artesian aquifer in 1975 and has not been reopened. Manitoba gypsum is used in cemem plants in Mani1oba and Saskatchewan and in wallboard plants in the three Prairie Provinces.

Jan 1, 1984

By G Anders

The effectiveness of two types of powder used in long-wall slashing was compared. The evaluation of the results can serve as a good example of how the application of statistical methods to underground test data can help to minimize the number of tests to be carried out. The conclusions are stated concisely, including a definite assessment of the reliability of the tests. Introduction AN assignment at the Algom Nordic mine called for a performance comparison between 70 per cent Cilgel B and 75 per cent Dygel in longwall stope slashing, particularly taking into account, in both cases, the build-up of bootlegs as dependent on hole deviation. Stopes were usually 8 to 10 ft. high and inclined at about 17 degrees. Starting from a raise, they were widened by consecutive longwall slashes to 60 ft., and, al-lowing for drift pillars, were approximately 300 ft. in length along the incline.

Jan 1, 1964

By R. M. Graves, C. B. McKenzie, D. Barbour, D. W. Desnoyers

"The prospective Tulks volcanic belt hosts five significant massive sulfide deposits, Tulks Prospect, Tulks East, Jack's Pond, Daniel's Pond and Victoria Mine, as well as numerous showings and indications throughout its 70 km outcrop length. Regionally, the 498 Ma sequence consists dominantly of felsic pyroclastic rocks and flows with interbedded mafic volcanic units and finegrained sediments, commonly graphitic. Contemporaneous granitoid rocks occur in the south half of the belt. Rocks usually display a strong NE-SW, steeply dipping, penetrative foliation and other shear-related high-strain fabrics. Facing directions are normally northwest, although there is local evidence of folding. Sulfide bodies and their alteration systems are deformed and shape-modified in the style of ambient strain.The Tulks, Tulks East and Jack's Pond prospects appear to occupy a similar stratigraphic level, on or near the contact between a thick felsic pile and an overlying broad, conductive package of graphitic sedimentary rocks. All are pyritic deposits with well-developed footwall alteration systems. The Tulks prospect comprises four polymetallic lenses totalling 750 000 t. Three lenses constituting more than 6 000 000 t of sulfide mineralization are indicated at Tulks East but only the 210 000 t ""B"" lens contains significant base metals. Jack's Pond consists of a very extensive, zoned alteration complex in which four lenses of massive to semi-massive pyrite + chalcopyrite are known. The central part of the system, characterized by Mg chlorite and carbonate, is enveloped by pervasive sericitization and capped by intensely silicified and pyritized volcanics. The sulfide lenses are interpreted as part of the footwall zone and are beneath that part of the system most likely to hostpolymetallic massive sulfides.Daniel's Pond differs from the other prospects in such fundamental ways as metal content, associated alteration and structural setting. The deposit comprises strongly tectonized, Ag-rich, Zn-Pb mineralization distinguished by a pronounced Ba-As-Sb signature. Mineralization is confined to a narrow, north-south high-strain zone which separates unstrained mafic volcanic rocks to the east from well-foliated felsic rocks. The deposit lacks an extensive alteration halo and at its north end is associated with a lens of barren, undeformed massive pyrite.The Victoria Mine deposit, the most cupriferous of the five, is related to a moderately dipping structure that separates well-foliated Tulks volcanic rocks from an overlying, less deformed volcanic sedimentary sequence that may be as young as 462 Ma. The structure is also the locus of black chlorite, dolomite and quartz alteration. Structurally remobilized precursor sulfide mineralization is one possible source for the deposit."

Jan 1, 1993

By S. Komar Kawatra, Youlian Zhou, Joseph A. Halt

"Bentonite clay has been the most common binder for iron ore pellets. Although bentonite increases pellet strength and durability, it has several disadvantages. For example, its use increases the cost of pellets and decreases pellet purity due to its composition and the higher levels of flux required to meet basicity limits. Several new types of binders have been proposed to replace clay. The binders include starch, modified humic acid (MHA), and dispersants. These binders were used to pelletize a magnetite concentrate from the United States. Typical doses of each binder type were 0.05-0.1 % starch, 0.5-0.75 % MHA, and 0.05 % dispersant. At these doses, the pellets exceeded the minimum recommended values for wet drop, dry compression strength, and fired compression strength. Pellets made with the MHA and dispersants had the lowest abrasion rates of the new binders, and were comparable to pellets made with bentonite clay. In this paper, we compare the new binders, considering pellet quality and the advantages and disadvantages of each binder type.INTRODUCTIONIron ore pelletizers need binders in order to make good quality iron ore pellets. The typical binder is bentonite clay, an alumino-silicate material. Bentonite increases the ballability and strength of iron ore concentrates, but reduces pellet iron grade and reducibility. As high quality bentonites can be expensive to ship, low quality bentonites are often used at significantly higher doses – this reduces iron grade and reducibility even further. Thus, several new types of binders have been proposed to replace bentonite clay.In this paper, we present several new binders for iron ore pellets: starch and modified humic acid (MHA). These have been tested alone and in mixtures with dispersants, or else with bentonite clay. Starch, MHA and their mixtures are briefly described below."

Jan 1, 2016

By J. P. Mogan, E. D. Dainty

Polynuclear aromatic hydrocarbon (PAH) levels were measured in underground mines in the vicinity of diesel vehicles equipped with several types of emission control hardware. In general, the emission control devices appeared to reduce PAH levels, but the companion mutagen study suggested that the reduction might not always be beneficial. All underground PAH concentrations were below the threshold at which a significant impact on health might be expected, but recent animal exposure studies have indicated that PAHs may not be the primary hazard from chronic diesel fume exposure.

Jan 1, 1994

By E. P. Cadwell

"Throughout the years Cyanamid has been a supplier of cyanide and a supplier of information to the mining industry. In general, the knowledge of mineralogy is greatly overlooked. Mineral deposits in the Western hemisphere have been exceedingly rich in the past but now they are becoming poorer. In other words, we will have to use our talents to the utmost to extract the precious metals and base metals from these ores. Modifications of some of the mineralogical equipment displayed here belong in the mill.Cyanidation of copper has been one of the main projects in our labs in recent years. De-rimming or de-filming of copper in order to upgrade copper concentrate was the main aspect investigated. A study was made as to how wide spread was the filming of secondary copper on pyrite, and to what extent it affected the copper industry. It was very wide.Often there is no conception as to what the minerals are. One open pit copper producer with a chalcopyrite ore was producing a copper concentrate with a 5% copper value whereas chalcopyrite contains 35% copper. They used primary and secondary grinding and a regrinding section. The ore contained about 8 parts chalcopyrite to one part of other copper minerals. In tests, a 3 1/ 2% copper rougher concentrate, cleaned without regrinding but conditioned with cyanide for a low contact time of 30 seconds produced a 30% copper concentrate with 90% recovery by removal of the film. It was of utmost importance that some quantitative mineralogical analysis be made before flow sheet changes were made. Every man should be trained to do his own microscopic examination in order to get quick answers. The fundamental thing in all mineral dressing is to first of all know the minerals and the mineral associations."

Jan 1, 1964

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it's process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004

By Seher Ata

"Virtual reality, a three-dimensional computer generated environment, has become recognized delivery system for many forms of education. This article describes the application of virtual reality to mineral processing education. An interactive mineral processing visualisation module has been developed at University of New South Wales (UNSW), Australia. The module provides students with an overview of a base metal concentrator, details about each stage of the process, as well as revealing how the mined ore progresses from stage to stage. The module also involves developing a number of instructional based plant layouts and flowsheets in the virtual environment that are intended to assist the user in understanding the essential components of the base metal concentrator.INTRODUCTIONVirtual Reality (VR) is the creation of an artificial environment that is experienced through sights and sounds provided by a computer (Squelch, 2001). The simulated environment is achieved through a host of technologies such as three-dimensional graphics, audio feedback and special peripheral devices to produce interactive environments.VR has been used in diverse fields including medicine (Riener & Harders, 2012), entertainment (Hsu, 2011), military (Manojlovich, Prasithsangaree, Hughes, Chen, & Lewis, 2003), manufacturing (Zimmermann, 2008; Jiang, 2011), and chemical processing (Schofield, Lester, & Wilson 2005; Squires, Andersen, Reklaitis, Jayakumar, & Carmichael, 2014). VR is also becoming recognized delivery system for many forms of education, including engineering education (Bell & Fogler, 1996; Bell & Scott, 1998; Shin, 2002). For example, virtual laboratories have been designed and developed to teach students fundemental features of the heterogeneous catalytic mechanisms and absorption columns (Bell & Fogler, 1995), the multi-phase and multi-component blast furnace iron making process (Babich & Senk, 2009) and to guide students to identify various safety measures while working in real laboratory (Bell & Fogler, 1996)."

Jan 1, 2016

By E. S. Moore

GOLD was discovered previous to the year 1900 on the east shore of Emerald lake, Afton township, Timagami Forest Reserve. It was found in a small cavern in banded iron formation, close to the water's edge. This occurrence of gold was mentioned in several reports that referred briefly to this area, and prospectors evinced considerable interest in the region. It was not, however, until the Golden Rose Mining Company, which was incorporated in 1909, started operations that much work was done on the property. In 1915-16, this Company, under the direction of E. J. Townsend, the President, did a considerable amount of work. A small mill was built and ore was extracted from pits, trenches, and a one~ hundred-foot shaft. In 1927, Afton Mines, Limited, was incorporated to take over the property, and about thirty men were employed for a time. During 1934, the New Golden Rose Mining Company was organized to handle the property, and the Consolidated Mining and Smelting Company of Canada, Limited, undertook to develop the mine. In March of the following year, this Company began deepening the shaft from 100 feet to 500 feet. A considerable amount of drilling had previously been done on the hill of iron formation in which the mine is located. Further drilling was done from the surface, and altogether about twelve holes have been put down to test the formations. Over 2,000 feet of drilling has also been done from the underground workings. The mine is now known officially as the New Golden Rose mine, although to many it is better known as the Afton. To reach the property during the summer months, there is a boat trip of about thirty miles from Timagami, a wagon-road portage of one mile to Obabika lake, a boat trip of ten miles on this lake, and finally a wagon-road portage of one and one-quarter miles to Emerald lake. The mine lies about three-quarters of a mile down the east shore of the lake. A 75 h.p. Diesel engine and compressor were taken in over this' route last summer, and it is evident that the transportation problem is quite a serious one. Airplanes have been much in use, and a winter road runs from the mine to Chudleigh, on the .Canadian National railway near Sudbury.

Jan 1, 1936

By O. A. Ojo, O. A. Idowu, N. P. Wikstrom, M. C. Chaturvedi

Transient Liquid Phase Bonding (TLP) of a Nickel base superalloy, Inconel 738, was performed to study the influence of holding time, filler gap size, and temperature on the joint microstructure. Insufficient holding time for complete isothermal solidification of liquated insert caused formation of eutectic-type microconstituents along the joint centerline region. An increase in the eutectic thickness with increase in initial filler gap size was observed in joints prepared at a constant temperature and holding time. In agreement with prediction by conventional TLP diffusion models, an increase in bonding temperature for a constant gap size, resulted in decrease in the time, tf, required to form a eutectic-free joint by complete isothermal solidification. However, a significant deviation from these models was observed in specimens bonded at and above l 175°C. A reduction in isothermal solidification rate with increased temperature was observed in these specimens, such that a eutectic-free joint could not be achieved by holding for a time period that produced complete isothermal solidification at lower temperatures. Considerable enrichment of the liquated insert with base metal alloying elements at higher temperatures is suggested to be an important factor contributing to the observed departure from conventional TLP prediction.

Jan 1, 2006

By Shigeru Sarata

A wheel loader is one of the main loading machines in open pit mines. The authors have been conducting research and development on autonomous operation of loading by a wheel loader. The most common loading method by a wheel loader is the ?V shape? path method. The loading operation consists of cycles of scooping from the pile, traveling to the dump truck, loading on the dump truck and return traveling to the scooping point for the next cycle. The traveling path includes a switchback in the middle of the path. The moving direction of the loader is changed at the switchback point. From observation of V shape path loading operations by experienced human operators, it seems that they control the bucket position between the scooping point and loading point on a shorter path for higher productivity. A new path planning method is proposed this paper, whereby a point on the center of the tip of the bucket is controlled moving from the initial point and the final point. The motion of the controlled point is generated by the wheel steering the wheel loader. The controlled point is moved along the direction to the final point; however, the motion and mechanism of wheel loader have restrictions, such as the velocity of the loader, the steering angle, and the steering angular velocity. Because of these restrictions, the path of the controlled point is not a straight line between the initial and final points. When this control method is applied between the scooping and the dumping points directly, the planned path is not stable in the leaving wing of V shape path. Therefore, the initial position of the wheel loader is set at the switchback point, then two approach wings to the scooping and the dumping points are made. The whole planned path is obtained by connecting the two paths. The shape of the planned path is strongly affected by the position of the switchback point, as well as the scooping and the dumping points. By simulation of path planning at different switchback points with the combination of the scooping and the dumping points, the paths for more effective loading are determined. The results of the simulation are presented in the paper.

Aug 1, 2013

By Frank Baczek, R. Q. Honaker, D. P. Patil, B. K. Parekh

Fine refuse slurry impoundment is a requirement for the coal industry to dispose the fines. Impoundment maintenance is an on going problem for the coal industry and its breakage creates environmental as well as financial problems. Deep Cone thickener technology which has been successfully applied in the alumina industry to dewater red mud was evaluated for fine refuse slurry. Preliminary obtained in a pilot-plant test showed that properly flocculated conventional thickener underflow slurry could be thickened to about 52.5 wt % solids and could replace belt filter press. The Deep Cone thickener was also found to dewater clean coal slurry to about 70 wt % solids. Further testing of the unit at other coal preparation plant is in progress.

Jan 1, 2004

By G. Riveros

A new, continuous fire refining process for copper has been developed and tested at the 5 tph pilot scale. During oxidation, the blister copper flows through a packed bed of crushed refractory bricks counter-current to a hot oxygen containing gas. The resulting desulphurized copper flows then directly into a packed bed of charcoal for deoxidation. By controlling the air to natural gas ratio, both temperature and reducing conditions can be controlled. Based on extensive laboratory scale measurements of the rate of copper oxidation and reduction, the process concept was developed aided by process modeling and simulation. The industrial-pilot scale installation built at the ENAMI Paipote smelter in Chile, consists of two cylindrical, compact reactors, operating in line, with a designed capacity of 5 t/h of blister copper. The results of the industrial-pilot tests confirmed the feasibility of the new process. The blister copper processing capacity was increased to 10 t/h with satisfactory sulphur removal. The degree of oxidation as well the copper temperature was controlled with relative ease. The specially designed siphon block allowed for smooth tapping of the oxidized copper and separation of refining slag. The reduction of oxidized copper in the packed bed of charcoal appeared to be very effective while control of the degree of reduction according to the height of the bed ensured control of the oxygen content in the refined copper at the required level.

Jan 1, 2007