Search Documents

By H. A. Kishawy, S. Kannan, M. Balazinski

Metal Matrix Composites (MMCs) are new generation engineering materials that possess superior physical and mechanical properties compared to nonreinforced alloys. However, the presence of abrasive ceramic reinforcements in the ductile matrix causes severe tool wear and premature tool failure. Flank wear was found to be the dominant wear mode while the main wear mechanism was abrasion. Analysis of the cutting tools using scanning electron microscopy has shown that both two body and three body abrasion are operational during machining MMCs. A methodology for predicting the tool flank wear progression during bar turning ofMMCs was presented in an earlier paper [1]. In the proposed model, the wear volume due to two body and three body abrasion mechanisms was formulated. Then, the flank wear rate was quantified by considering the tool geometry in 3D turning. The main objective of this paper is to investigate the contribution of two body and three body abrasion towards the tool wear volume during cutting MMCs.

Jan 1, 2006

ABSTRACT The SART (sulphidization, acidification, recycle, and thickening) process is an effective way to separate copper and cyanide in the waste stream of gold processing plants using cyanidation. Factorial experimentation has been conducted to create models of copper recovery, cyanide recovery, acid addition, and oxidation/reduction potential during SART. Economic analysis of the resultant models showed that SART is best operated with a sulphide-to-copper molar ratio of approximately 0.56, pH of 4, and a minimized cyanide-to-copper molar ratio. The experiments also showed th0at residence time can have drastic impacts on SART performance.

Jan 1, 2013

By C. Jay Hodgson, Adrienne C. L. Larocque

The Mobrun VMS deposit in northwestern Quebec does not fit the classic Noranda type model, but exhibits characteristics more consistent with a Mattabi-type deposit. The orebodies are underlain by fragmental volcanic rocks indicative of explosive volcanism in shallow water. Felsic volcanic rocks are more abundant than mafic rocks. Alteration assemblages comprise chlorite, carbonate, sericite, and quartz. Broad semi-conformable alteration occurs high in the footwall to the 1100 lens. Mobrun occurs higher in the stratigraphic sequence than most of the other deposits in the Noranda camp. In this part of the stratigraphy, zones of pervasive carbonatization may be more useful guides for exploration than zones of silicification.

Jan 1, 1993

By C. R. Edwards, D. G. Feasby

"Over the last 50 years disposal of uranium mill tailings has evolved from dumping untreated tailings into the nearest depression to depositing chemically-stabilized tailings into highly engineered management facilities. This paper describes the evolution of disposal methods and the criteria which have determined the development path followed. Remediation techniques to bring older and now unacceptable tailings deposits into satisfactory compliance with today's· regulations are reviewed.With the closure of the uranium mines in Elliot Lake, Ontario, considerable effort is being made on decommissioning the tailings areas by developing long term maintenance of water covers. The innovative methods being used to develop these water covers are detailed. Methods now under development in Saskatchewan for subaqueous deposition of high density or paste tailings for permanent disposal in mined out open pits are described.SummaryThe technology for uranium mill tailings disposal in Canada has evolved considerably over the past 51 years. This evolution has been driven by an improving understanding of how best to safely and permanently store tailings, in conjunction with stricter environmental protection regulations. Old sites are being decommissioned in situ, but may require long term care and maintenance. The use of water covers is an important technique in eastern Canada to prevent intrusion, radon evolution and, for the Elliot Lake tailings, acid generation. The major drawback of water covers in any above ground disposal method is the requirement that a long term maintenance and monitoring plan be put into effect for each site.New higher grade mines in Saskatchewan will increasingly use disposal in mined-out pits using the pervious surround method and/or paste tailings technology as a method to permanently dispose of these wastes and to permit “walkaway” after a few years of monitoring."

Jan 1, 1996

By S. Makni, S. Koppalkar, A. Bouajila

This paper reviews briefly the gravity recovery involving conventional gravity separators and centrifugal gravity separators. The advantages of semi-continuous gravity separators will be discussed. Techniques for upgrading the gravity concentrates will be addressed briefly. The research efforts in optimizing semi-continuous gravity separators will be recalled. Innovative gravity circuit for eliminating or minimizing the use of complex processing schemes will be reviewed. On-going gold gravity research at COREM has revealed that gold particle shape transformation is the main factor explaining the lower recoveries of the plant units. Efforts to devise possible remedies for improving gravity recovery at plant will be discussed.

Jan 1, 2011

By José Cáceres

Mine To Mill? ? Carlisle(1954) ?The economic of a fund resource with particular reference to mining?. ? Steine(1978) ?Coarser grind may mean lower metal recovery but higher profit?. ? Metalica (1999) ?Mine Plant Integrated Planning?. ? JK (2002) Mine to Mill Strategic Planning ? Camus, Kelebek (2002) ?Management of Mineral Resources: Creating Value in the Mining Business?. ? Caceres (2003) ?Integrating Milling Parameters in the Mining Planning?

May 1, 2006

By J. O. Yeboah, V. Boakye, P. A. Bepswa, M. Lombard, G. Nutor

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By E. Benguerel, G. Monteith, L. Centomo, S. Pelletier

In early 2007, it became apparent that with changing concentrate feeds, the magnesium (Mg) load projected for CEZinc starting in 2009 and beyond would quadruple and overwhelm the current Mg process bleed capacity. A project was started, following design for six sigma (DFSS) standards, to select both the optimal process and to evaluate its target capacity for the Mg bleed circuit. The economic and process risks of under or over-designing while Mg reduction efforts were underway at the mines also needed to be evaluated. This paper describes the project methodology, the impact on the plant, and some potential optimizations for CEZinc's basic zinc sulphate (BZS) Mg bleed process.

Jan 1, 2008

By B. L. Dorey

"Performance management is a systematic, practical approach to managing people. It is founded on some basic assumptions about people and is designed to focus on people in the work place. Organizing meaningful information and using it to involve people is a cornerstone of this system.Some common sense practices are developed to involve people in an organization's effort to improve performance. The successful implementation of this program requires solid commitment and total involvement from all levels of supervision and employees for maximum results and lasting impact. All levels of supervision participate in training sessions to tailor the systems for implementation in their areas. This style of management is data-oriented and the bottom line of success is to measurably improve performance. Basic Assumptions about PeopleMost people in an organization, regardless of level, take pride in their work and generally want to do a good job. When performance falls off, there is usually some explanation other than the employee not really caring. People like to know their exact responsibilities and clearly what is expected of them. People like to know where they stand with the boss and would like to be evaluated on what they do and accomplish, rather than on what others think or feel about them. Further, people like to be rewarded for their good results, indeed, to understand what motivates people, we must look at what happens as a result of their actions. Another belief is that supervisors often have a greater influence on the performance of their people than they fully realize. Simply letting people know how important their performance is can have an impact. The Key ElementsGiven these basic assumptions and beliefs about people, some common sense practices have been systematically developed to manage more effectively."

Jan 1, 1989

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008

By R. T. Seaman

There are several hydrometallurgical alternative processing options under development for high enargite and arsenic containing copper concentrates ranging from biological, atmospheric, medium temperature oxidation to total oxidative leaching. The most developed of these options is the CESL process boasting pilot campaigns totaling more than 8760 hours of fully integrated continuous operation, as well as, over two thousand batch scale oxidation tests performed on dozens of concentrates for flowsheet development. This paper reports the observed deportment of arsenic under varying arsenic, iron and acid oxidation conditions; it also describes the impact of iron to arsenic ratios and residue recycle on overall arsenic behavior and its stability in residue. INTRODUCTION The CESL Hydrometallurgical Process (CESL) was originally developed to compete with smelting of clean chalcopyrite concentrates. High Treatment Charges and Refining Charges (TC/RCs) combined with premiums on London Metal Exchange (LME) grade copper from onsite refining made treatment of copper concentrates using CESL a viable option at the time. As world demand for copper increased and a subsidized Chinese refining market developed, smelting contracts became more favourable for the miner and focus was placed on modifying the CESL Hydrometallurgical Process to handle concentrates with elevated deleterious elements. Dozens of pilot campaigns processing concentrates containing elevated concentrations of uranium, fluoride, mercury and nickel all led to further developments of the CESL Hydrometallurgical Process. In 2016 a United States patent was granted for a novel modification of the CESL Hydrometallurgical Process for recovery of copper from arsenic-bearing and/or antimony-bearing copper sulphide concentrates, Henry Salomon de Friedberg (2016). To date, over 2000 bench scale tests along with five fully integrated closed loop pilot campaigns, totaling over a year of online operation time, have been conducted processing arsenic bearing copper concentrates. This paper summarizes the observed behavior of arsenic under varying autoclave and process conditions.

Jan 1, 2019

By J. R. Smith

"The Lake Dufault orebodies were discovered by deep surface diamond drilling. When a reasonable amount of outline drilling had been completed, the decision to go into production was made. The fact that shaft sinking, lateral development, the detailing of the orebodies and stope preparation were to be carried out as rapidly as possible necessitated very close scheduling.After a study of varions possible mining methods, an open-stoping system using long-hole blasting was chosen. Diesel-powered Transloaders were selected for the mucking and transportation of ore from the drawpoints to the orepass.At the time of writing, the choice of mining method appears to have been fully justified, although more time will be required to arrive at true operating costs and efficiencies."

Jan 1, 1966

By H. J. Hartjens

"With the trend towards bringing into production ore bodies of lower and lower copper content every possible avenue of approach to achieve maximum copper metal recovery and keep milling costs to a minimum are of increasing importance.Equipment manufacturers have contributed a great deal by designing larger mills, flotation machines, pumps, etc. in lowering capital and operating costs; instrumentation and automation usually as a joint effort of operating staffs and equipment manufacturers have resulted in lower operating costs and improved metallurgy. Likewise manufacturers of chemicals used in mineral beneficiation have directed their research and development at new flotation reagents and treatment schemes to complement the needs for more efficient products, permitting coarser grinds without detriment to recovery, higher flotation rates, higher degrees of selectivity, as well as chemicals to improve settling, clarification and filtration. The various treatment schemes in use and suggested for consideration are:1) The choice of the flotation treatment scheme is largely dictated by the desire to operate a simple circuit, originally consisting of rougher and scavenger flotation, with scavenger concentrate either returning to the head of the rougher circuit or joining the rougher concentrate for cleaning by reflotation, with and without prior regrinding. The cleaner tailing was also recycled to the head of the rougher circuit. In the case of porphyry copper ores, this was originally the standard circuit. Lime is the preferred alkalinity regulator to adjust pH, usually in the range 10-12.To avoid the undesirable effects of circulating loads and gain the advantage of simplified control of the rougher circuit, open circuit cleaning is practiced more and more. In this scheme, cleaner tailing is scavenged to produce a discardable tailing and the scavenger concentrate returned either to the cleaner or the regrind circuit."

Jan 1, 1970

By Mark W. Masson, David B. Stevenson, David W. Broughton, Douglas R. Cruji, Steven E. Parry

"Abstract-The Amalgamated Kirkland gold deposit is located at Kirkland Lake, Ontario, within the Archean Abitibi Greenstone belt of the Canadian Shield. It lies on a fault or "break", termed the Cyprus Break, which is a splay off a regional structure termed the Cyprus-Battle Mountain Break. The Cyprus Break merges with the Cyprus - Battle Mountain Break above the -250 m level, as it was not encountered in shallow drilling or surface exploration. These structures lie 1.5 km south of the 727 000 kg (23 million ounce) Kirkland Lake Main Break and 0.5 km north of the 872 000 kg (30 million ounce) Larder Lake Break.The deposit is hosted by alkalic Timiskaming Group volcanic and sedimentary rocks which are overthrust by older Larder Lake Group tholeiitic and komatiitic flows along the Larder Lake Break. Timiskaming syenitic intrusives, similar to the host rocks for the Kirkland Lake Main Break gold deposit, intrude both suites.The Amalgamated Kirkland deposit consists of lode-style gold mineralization which is mainly hosted by altered and pyritized Timiskaming trachytic volcanics which wedge out or thin at depth, between two sedimentary units. The intersection of the Cyprus - Battle Mountain and Cyprus Breaks, in conjunction with the westward plunge of the volcanic wedge, appears to control the westerly plunge of the Amalgamated Kirkland deposit at approximately 50º.Mineralization is characterized by blue-gray brecciated and "wormy" quartz-ankerite veins which contain up to 10% fine-grained pyrite and, in decreasing order of abundance, minor galena, chalcopyrite, sphalerite, molybdenite and visible gold. The sulfides and gold commonly occur along fractures and wallrock inclusions within the veins. Native gold occurs as fine pinpoints distributed in 1-mm to 5-mm size clusters of up to ten or more grains.The auriferous veins occur within a quartz-ankerite-sericite-pyrite alteration assemblage which is enveloped by a broader zone of ankerite-sericite±hematite±quartz-pyrite alteration up to 60 m wide. This latter assemblage overprints the regional greenschist-facies chlorite-calcite assemblage.The Amalgamated Kirkland property has had a long history of exploration activity beginning with the first discovery of mineralization in 1911 on the Hunton Shaft claim located in the northeast corner of the property. Since that time various prospecting, mapping, trenching, geophysical surveys and diamond drilling programs have concentrated on either carbonate zones along the Larder Lake Break or quartz veins along the northern side of the property in association with complex trachyte flows and syenite dikes.Battle Mountain Canada Inc. located the Cyprus - Battle Mountain Break through a prospecting, trenching and geophysical program in 1989. Drilling by Battle Mountain and Cyprus Canada under the surface showing, coupled with several revisions to the structural interpretation of the Cyprus - Battle Mountain and Cyprus Breaks, resulted in delineation of the Amalgamated Kirkland deposit. Location of an auriferous structure through basic surface exploration within 1 km of a world-class orebody demonstrates both the subtle nature of Archean gold deposits and the potential for finding new mineralization in heavily prospected camps."

Jan 1, 1995

By Mark W. Masson, David B. Stevenson, David W. Broughton, Douglas R. Cruji, Steven E. Parry

"The Amalgamated Kirkland gold deposit is located at Kirkland Lake, Ontario, within the Archean Abitibi Greenstone belt of the Canadian Shield. It lies on a fault or “break”, termed the Cyprus Break, which is a splay off a regional structure termed the Cyprus-Battle Mountain Break. The Cyprus Break merges with the Cyprus – Battle Mountain Break above the -250 m level, as it was not encountered in shallow drilling or surface exploration. These structures lie 1.5 km south of the 727 000 kg (23 million ounce) Kirkland Lake Main Break and 0.5 km north of the 872 000 kg(30 million ounce) Larder Lake Break.The deposit is hosted by alkalic Timiskaming Group volcanic and sedimentary rocks which are overthrust by older Larder Lake Group tholeiitic and komatiitic fows along the Larder Lake Break. Timiskaming syenitic intrusives, similar to the host rocks for the Kirkland Lake Main Break gold deposit, intrude both suites.The Amalgamated Kirkland deposit consists of lode-style gold mineralization which is mainly hosted by altered and pyritized Timiskaming trachytic volcanics which wedge out or thin at depth, between two sedimentary units. The intersection of the Cyprus – Battle Mountain and Cyprus Breaks, in conjunction with the westward plunge of the volcanic wedge, appears to control the westerly plunge of the Amalgamated Kirkland deposit at approximately 50º.Mineralization is characterized by blue-gray brecciated and “wormy” quartz-ankerite veinswhich contain up to 10% fne-grained pyrite and, in decreasing order of abundance, minor galena,chalcopyrite, sphalerite, molybdenite and visible gold. The sulfdes and gold commonly occur alongfractures and wallrock inclusions within the veins. Native gold occurs as fne pinpoints distributed in 1-mm to 5-mm size clusters of up to ten or more grains.The auriferous veins occur within a quartz-ankerite-sericite-pyrite alteration assemblage which is enveloped by a broader zone of ankerite-sericite±hematite±quartz-pyrite alteration up to 60 m wide. This latter assemblage overprints the regional greenschist-facies chlorite-calcite assemblage.The Amalgamated Kirkland property has had a long history of exploration activity beginning with the first discovery of mineralization in 1911 on the Hunton Shaft claim located in the northeast corner of the property. Since that time various prospecting, mapping, trenching, geophysical surveys and diamond drilling programs have concentrated on either carbonate zones along the Larder Lake Break or quartz veins along the northern side of the property in association with complex trachyte flows and syenite dikes.Battle Mountain Canada Inc. located the Cyprus – Battle Mountain Break through a prospecting, trenching and geophysical program in 1989. Drilling by Battle Mountain and Cyprus Canada under the surface showing, coupled with several revisions to the structural interpretation of the Cyprus –Battle Mountain and Cyprus Breaks, resulted in delineation of the Amalgamated Kirkland deposit. Location of an auriferous structure through basic surface exploration within 1 km of a world-class orebody demonstrates both the subtle nature of Archean gold deposits and the potential for finding new mineralization in heavily prospected camps."

Jan 1, 1995

By Man-Chao He

One of the critical problems involved in deep coalmines is unusual gas emissions. Many researchers agree that there is a relationship between coal gas emissions and geological features such as tectonics or geological disturbances, gas content, properties of the coal and rock and the mininginduced stress state in the coal seam and rock. Thus, the present paper intends to investigate complex mechanical phenomena during the process of gas emission in underground coal-mines. A program of laboratory testing was undertaken to study the effects of temperature and pressure on mechanisms of gas emission. It must be noted that this paper describes new techniques developed to simultaneously measure deformation and gas pressure, as well as flux during the test, taking the characteristics of gas transport into consideration under certain temperature and pressure conditions. The results indicate that under certain temperature and pressure conditions, gases adsorbed to coal start to desorb, and increase the pore pressure. High pressure gases entering coal fractures can generate high tensile stresses near the crack tips, leading to crack propagation and coalescence, which in turn can cause the specimen to dilate. From the experimental viewpoint, these test results may help us discern why mining seismic events can trigger gas emissions.

Aug 1, 2013

By J. Bouchard, R. del Villar, A. Vazirizadeh

"Industrial flotation is a continuous and often multistage process, where particles of a given mineral species (usually the targeted one), present in different sizes, encounter a large amount of gas bubbles (normally air) to produce mineral–bubble aggregates, which are removed from the flotation device (cell or column) as a valuable product (concentrate). The bubble content inside the cell is characterized by the prevailing hydrodynamic conditions (known as gas dispersion variables), which in turn are known to influence the flotation performance. Although most researchers and practitioners agree that the relationship between the hydrodynamic variables and flotation performance exists, the lack of an adequate method foronline measuring the average bubble diameter has prevented such studies.The aim of this study is to apply appropriate hydrodynamic variables for flotation kinetic modeling (as a key feature of flotation performance) for a given introduced particle size distribution (PSD). In this regard, experiments were conducted in a laboratory flotation column (5.6 cm internal diameter for a total height of 650 cm), and mixtures of quartz (hydrophilic gangue) and talc (naturally hydrophobic mineral), classified in four different size fractions. The correlation between the flotation rate constant and given hydrodynamic variables were analyzed. Results suggest that the relative importance of hydrodynamic variables for flotation rate modeling depends on the PSD. Finally the suggested hydrodynamic variables for each of the various particle size-classes considered were used to produce single variable models for the flotation rate constant. INTRODUCTIONIndependently of the prevailing flotation conditions, the mechanisms for bubble-particle aggregation and the residence time of the phases inside the device must also be considered. In this regard, one of the most used approaches to represent the overall flotation process is as a pseudo-chemical reaction between a particle and a bubble, whose rate (at a given time) is proportional to the amount of remaining floatable species. The proportionating constant is called the kinetic constant or the flotation rate constant."

Jan 1, 2016

By Z. Gostynski

The paper is a historical cross-section through a 28-year period of operation of the direct-to-blister Flash Smelting Furnace in the KGHM Glogów Copper Plant. It presents the origin of the furnace as well as the path of numerous changes and modifications both in technology and process introduced in the furnace in response to the production and cost-reduction challenges. The authors provide justification of the statement that continuous improvement of the "Polish" Flash Smelting Furnace has ranked it among the most modem smelting units in the world.

Jan 1, 2007

By R. B. Humphrey

Cut-and-fill mining methods at the Thompson Mine have undergone significant changes since production began in 1961. Changes have been introduced in almost all aspects of the mining operation, from the original timbered chutes and air-operated slushers to the present-day bored raises, footwall ore passes and load-haul-dump units. This paper describes the evolution of mechanized cut-and fill mining methods, highlighting the changes in design for stopes and service openings, ground support methods; hydraulic filling and ventilation systems. A mechanized stoping area is described from the initial mining concept through design, development, construction and mining cycles.

Jan 1, 1979

By Xue Yang

Even though many approaches have been proposed for automated fault detection and diagnosis of Heating Ventilation and Air Conditioning (HVAC) systems, and advanced maintenance programs, such as preventive and predictive maintenance have been applied for the systems, issuing work orders for corrective maintenance is still a reality. Currently corrective maintenance still accounts for more than 55% of all maintenance programs in average facilities in the US (DoE, 2010). Indoor air related problems are especially important among corrective maintenance work orders. This paper provides details of a case study conducted to capture the workflow that HVAC mechanics follow, their rationale in diagnosis process and the information they typically refer to while responding to indoor air related corrective maintenance work orders. The general workflow for HVAC mechanics to complete such types of work orders was summarized into 5 stages, and generic information requirements recorded from the case study were synthesized. Initial findings show two main challenges in the industry for HVAC mechanics to get access to required information, which highlights the need for a systematic approach that would enable identification of such information applicable to a given context under which a work order has been generated and provide values of required information for HVAC mechanics to do sound diagnosis through integrated data repositories.

Aug 1, 2013