Search Documents

By Kremena Dedelyanova

The paper presents research of mechanism for the creation of air bubbles in vibratory a column flotation machine. Factors are discussed that influence the increase in the duration of the bubble in the area of contact with the mineral particles. Formulas are derived for the parameter effect of vibrations, applicable to the design of flotation machine. The collision efficiency of the bubbles in a vibratory column flotation machine is determined.

Aug 1, 2013

By A. Zangooi, J. A. Finch

"A frother analysis technique based on the formation of a colored solution with UV-VIS absorbance proportional to frother concentration over a certain range has been developed. The calculation of concentration requires the comparison of the sample absorbance at a selected wavelength with a linear calibration (frother concentration vs. absorbance) constructed with values collected from solutions of known concentration (standards) at the same wavelength. It has been found that concentration ranges for preparation of standards can vary widely. An integration of our experiences into a databank can offer some guidance on the selection of standard concentrations. The databank includes results from the analysis of 37 chemical reagents, commercial frothers, and natural oils used in research work or at industrial sites. Grouping frothers by similar chemical structure or origin provides a good basis for selecting the standards to approach the maximum absorbance range for the spectrophotometer in use.INTRODUCTIONA technique to determine frother concentration on samples of industrial milling streams based on formation of a colored solution with UV-VIS absorbance proportional to frother concentration has been developed. The concentration is determined by comparison of its absorbance, at some selected wavelength, with those obtained by processing a series of solutions of known concentration (standards), at the same wavelength. It is desirable to have linear calibration (frother concentration vs. absorbance) over the widest concentration range. The upper concentration can be restricted by the instrument, as there is a maximum detectable absorbance (minimum transmittance), which can be reliably sensed by the UV-VIS detector (in most cases maximum absorbance is 3)."

Jan 1, 2016

By Frank D. Shepherd

THE Gunnar Gold Mines property is on the west shore of Beresford lake, in the Rice Lake mining division, southeastern Manitoba. Gold was first discovered in place in the Rice-Beresford Lakes area in 1911 on the Gabrielle claim, now included in the San Antonio Mines property at Rice lake. Following an eastward trend of favourable prospecting ground, promising showings were next staked in the vicinity of Long lake during the years 1915 and 1916. At that time, William Walton and associates, among them Gilbert LaBine, staked the Eldorado vein, north of Long lake, and Eldorado Gold Mines, Limited, was formed to develop the property a Company that, later, was to become widely known through successful operation of its radium-silver mine at Great Bear lake, Northwest Territories. Continuing eastward from Long lake, Walton and his partners, Gunnar Berg, Leo Seaberg, and Wm. Quesnel, staked claims during the years 1920-24 in the vicinity of Beresford lake which, later, were to become incorporated into the Gunnar Gold Mines property. The presence of gold-bearing quartz on these claims had been known from the time they were staked, but an opportunity to consolidate them into a group was not forth-coming until early in the year 1933. Although promising gold showings had been disclosed during the performance of assessment work on individual claims, no continuous mineralization having mine-making possibilities was discovered until after the consolidation of the entire group. From this stage onward, progress was rapid. Active exploration was begun on August 1st, 1933, and late in October James Houston reported favourably on the property. On October 27th, Gunnar Gold Mines, Limited, was incorporated in the Province of Ontario to develop and operate the property. The Company is also registered in Manitoba. The authorized capitalization is 3,000,000 shares of $1.00 par value. Gilbert LaBine was appointed president of the Company, with James Houston as mine manager. Following completion of a diamond-drilling programme, planned in 1933, it was decided to install a mine plant capable of carrying development to a depth of 1,000 feet. A transmission line, 5 miles in length, was built to the Great Falls-Central Manitoba line of the Manitoba Power Company, Limited.

Jan 1, 1939

By Robert B. Parsons

"The Province of Manitoba tabled a Budget on March 11, 1992, which contains some important new initiatives designed to improve the fiscal environment for mining in the province. In addition, the Minister of Energy and Mines has released details of the Mineral Exploration Incentive Program which was originally announced in the 1991 Budget.Introduction""We recognize the important contribution o f mining to the economic activity of our province, including direct and service jobs and export earnings. We are determined to secure its future."" - The Honourable Clayton Manness, Minister of Finance, Province of Manitoba, March 11, 1992.With these words of introduction, Manitoba Finance Minister Clayton Manness announced a number of significant measures aimed at improving the fiscal regime for exploration and mining in Manitoba. At the same time, details of the Manitoba Mineral Exploration Incentive Program (MEIP) were released."

Jan 1, 1992

By K. Schimann, H. D. Knipping, J. P. Fouques

"The Cigar Lake uranium deposit, in the Athabasca area of north Saskatchewan, was discovered in May 1981 by Cogema (Canada) Ltd., as operator of the Waterbury Lake Joint Venture.The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sandstone, at a depth of 410 m to 450 m below surface.At the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25m and 105m. It has the shape of flat-lying /em 5 m to 30m thick and shows a remarkable longitudinal and lateral continuity from the information obtained to date. A well defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west trending structure within which a particular rock facies (""augen gneiss'') has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-AI rich clay minerals (illite-chlorite). The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfa-arsenides of nickel and cobalt. Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and although no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, there may be locally a good coincidence.However, a combination of several methods proved extremely useful in interpreting the regional geology and defining the drilling targets within the favourable areas.Although the Cigar Lake deposit shows many similarities with several classical deposits of the Athabasca region, it is characterized by the intensity of its alteration processes and the presence of massive, extremely high grade mineralization.At the end of 1984, the global geological reserves estimated by geostatistics on the main mineralized ""pod"" of the deposit amounted to 110,000 metric tonnes of uranium at an average grade of 12.2% U, with a precision of 25% at the 95% confidence level."

Jan 1, 1986

By M-A. Thibault, C. Gauthierand, J-P. Gagné, J-Y. Carrier, P. Rochette, G. Dufour

"Anodes consumed in the electrolytic process for the production of primary aluminium are considered consumables. They need to be replaced at regular intervals of approximately one month. The so-called anode butts which are removed from the cells contain the metal supports (rods), cast iron thimbles, crust and residual carbon material. Cleaning is required to remove the waste material before the rods are fitted with new anodes. An inspection is required to ascertain if repairs to the rods are necessary. Presently, this inspection is carried out visually. ST AS, in 2004 in collaboration with Alcoa Deschambault, initiated a project to develop an automated inspection system. The objectives were to find a technical solution to perform these functions with a very simple system. Such a system was designed around ""artificial vision"". The inspection system developed uses only one fixed camera and does not require a separate step in the process for the anode rod assembly to perform the inspection. This paper presents the initial steps of the work performed to develop the equipment and software as well as a summary of the results obtained."

Jan 1, 2006

By Richard E. J. Putman

THE MINERALS INDUSTRY has always been a heavy user of energy in most of its unit operations: power in the mining, comminution, flotation and electro-winning processes; fuel in its smelting and other metallurgical processes; and, of course, fuel in the on-site generation of power and steam. Many of the techniques for using computers to perform energy management and conservation tasks have been known for some time, but they have not been widely implemented because the return on investment has hitherto been insufficient. Recent trends, however, have not only caused the dollar return to rise due to higher purchased energy costs, but the cost of the investment to fall. One trend has been the generally lower cost of computer control systems themselves, due to vendors having adopted the newer, lower-cost and more reliable electronic component technologies now becoming universally available. The second trend is the development of low-cost, but high-speed, remote multiplexing devices, which have reduced considerably the expense of bringing data from points scattered over a wide area, which is typically the case when applying energy management systems to a minerals processing plant. By taking advantage of these and related developments, computer control systems can now have a rewarding impact on plant energy management and conservation practices, and recent advances in application technology have opened up new and additional opportunities for energy cost reduction and control.

Jan 1, 1978

By K. Johanson, M. Hubert, C. Eckert, D. Ghose

The mining industry routinely processes material with different particle sizes. Coal, nickel ore, copper ore, lignite, shale, and phosphate ore are all examples of materials with wide particle size distributions. It is often assumed that these materials are homogenous and that any particle size distribution has the same chemical activity and composition. It is entirely possible, and quite likely, that chemical composition is a function of particle size distribution. In addition, particle size distributions in ore materials are often responsible for the difference in flow behavior in process equipment. This is evident in coal electrical production facilities. Fine coal may have the same ash content, sulfur content, and BTU value as coarse coal. However, all electrical production facilities know the extreme flow problems that result when attempting to handle wet fine coal. Segregation of these bulk materials is an important issue that must be understood to prevent these cohesive flow problems. Additionally, fertilizers are mixtures of particles with different shape and sizes. These mixtures must remain homogenous to optimize fertilizer performance. Segregation leads to poor product quality. This paper presents a method of measuring the magnitude of sifting segregation occurring in bulk material and the relationship between the strength of the bulk material and the separation tendency. It shows an inverse relationship between the yield strength of the material and the bulk segregation.

Jan 1, 2004

By Shantanu Patel, C. Derek Martin

"The objective of this work is to develop a practical numerical approach for applying the confining pressure to discrete element cylindrical triaxial tests. A layer of membrane particles with very low stiffness and extremely high contact bond strength was created around the lateral boundary of the cylindrical numerical specimen. To prevent the membrane particles from penetrating into the rock specimen on application of confining forces and to provide a smooth boundary surface, the space between the membrane and rock particles was filled using small-diameter packing particles. The results of this method were compared with those of rigid boundary method with confining pressure of 20MPa. The results obtained show that new approach gives both peak strength and post peak response that are in closer agreement with laboratory findings. BACKGROUNDThe discrete element method (DEM) has become the cornerstone for simulating both intact material and discrete fractures for low porosity strong rocks (ISRM Classes R3 to R6). Despite the advances in its application, simulating realistic behaviour of intact rock using the DEM remains a challenge. The bonded particle model was introduced as a potential solution for simulating the complex mineral grains in strong rock and other granular materials (Potyondy and Cundall, 2004; Utili and Nova, 2008; Salot et al., 2009). While some issues were resolved, a remaining challenge is the lack of the bonded particle model to simulate the brittle response commonly observed in strong rocks during the triaxial compressive test. Such behaviour is shown in Fig. 1 for Lac du Bonnet Granite at a confining pressure of 20MPa."

Jan 1, 2015

By André Desbiens, Frédéric Flament, Lionel Ryan

"In December 1991, the GRAHM (Groupe de Recherche sur Jes Applications de L'informatique a L'industrie Minerale), of Laval University started a KBAC (Knowledge Based Automatic Control) grinding project with Falconbridge Ltd. The project was shifted to the Kidd Creek concentrator in the summer of 1992, with the first phase involving the collection of data by GRAHM and Falconbridge personnel for the construction and tuning of a dynamic simulator. This grinding circuit dynamic simulator known as DYNAFRAG was used to assess various control strategies, with a PID-based strategy being selected for ease of installation on a Foxboro II A DCS.The ""B"" primary grinding circuit was chosen for the initial strategy development, which is one of three parallel divisions. The KBAC project was successfully completed in November 1994, with subsequent modifications being implemented by Kidd Creek staff.This paper summarizes, the current control strategy, the project costs, and the realized benefits. Some of the problems which were encountered with the initial installation, and the subsequent modifications are also dealt with in this paper.2.0 IntroductionIn the summer of 1992, the GRAHM of Laval University and Falconbridge Ltd. started a project to design a control strategy for the ""B"" grinding circuit at the Kidd Creek Division. Between 1992 and 1994 several papers have been written to describe the control objectives, the methodology followed, and some initial results (Flament, 1994A, 1994B). Since then, however, the control objectives changed, and several improvements were made to the circuit. In particular, maximizing tonnage was no longer a priority, a variable speed drive pump was installed on the cyclone feed, the ball mill power was lowered, and the geometry of the cyclones changed. As a consequence, the control strategy was revised. Table 1 summarizes the historical developments on the ""B"" division grinding control."

Jan 1, 1996

By J. B. McKenzie

Since connnencing underground prcxiuction in 1979, the Ruttan Mine has been prone to secon:iacy sulphide dust explosions. Al though infrequent during the early years of prcxiuction, these occurrences did result in major damage and lost time injuries. 'As the mine exparrled and developed to further depths, sulphide dust explosions occurred on a more frequent basis. Incomplete ventilation se:rvices, required to exhaust the affected areas, caused frequent delays resulting in lower prcxiuction rates due to the time required to ventilate the affected areas of the mine. CUrrent procedures to minimize the effects of secon:iacy dust explosions evolved from practical suggestions arrl examining methcx:ls other mines have developed to cope with the problem. Procedures and regulations to protect errployees from exposure to hazards of sulphur dioxide are time consuming, expensive and counter prcxiuctive in their present fonn. This paper describes the history of secon:iacy sulphide dust explosions at the Ruttan Mine and the methcx:ls and proced.ures currently in place to minimize and contain the effects of dust explosions.

May 11, 1988

The original JKMRC AG/SAG mill model was developed over 30 years ago and has been upgraded a number of times since then, with the current published version being the Variable Rates model that is now over 15 years old. Since this model was developed further enhancements have been derived, some of which are applied in-house and some which have yet to be incorporated. The published and the commercially available model in JKSimMet is currently undergoing a comprehensive overhaul with a vastly extended data base for model evolution and validation. Improvements developed within the AMIRA P9 project, in-house development and a number of collaborative projects, are being incorporated into the upgraded model structure. Enhanced capabilities will include: power-based breakage rates scaling; a far wider mill filling range (from 10% to 40%) that exhibits peak in throughput as mill filling increases; higher ball loads; improved pebble discharge function; improved slurry discharge function incorporating important mill design and operational influences; and the new size dependent breakage function. The model will also be able to accommodate some influence of liner design and multi-component ores (blends of hard and soft components). This upgrade is still a work in progress but substantial changes have been made to date. This paper presents some of the new improvements and their influence on the predictive capability of the model.

Jan 1, 2012

Weekly Capacity ? Current Schedule Rate (198.5 tonnes / hour) X Skip Time (112.7 hours) X Effectiveness (85%) = Weekly Capacity (19,015 tonnes) Capacity Conclusions - Existing hoists optimized are best option for Fraser Morgan (>20M + schedule for other). - Peak will have to be managed. - Critical to have equipment & infrastructure in best possible condition to ensure reliability.

Feb 1, 2008

By Niels Verbaan, Ron Molnar, David Dreisinger

"An acidic chloride leach solution was generated from the treatment of an ore containing the following value elements: silver, gold, indium, gallium, copper, zinc and lead. Iron was also co-extracted into solution as a ferric chloride species. Iron extraction was a significant component of the overall acid consumption of the leaching process. The recovery of iron by solvent extraction and water stripping was investigated. Tri-butyl-phosphate (TBP) was very effective at recovering iron from the leachate. The water strip solution could be decomposed to produce ferric oxide (hematite) and hydrochloric acid for recycle via hydrothermal hydrolysis or pyrohydrolysis.INTRODUCTION The Malku Khota deposit is situated in the eastern part of the Bolivian Altiplano at elevations between approximately 3,800 and 4,580 meters above sea level (Figure 1). The project is located 98 km east-southeast of Oruro, and 85 km south of Cochabamba in a relatively remote area."

Jan 1, 2016

By H. E. (Buzz) Neal

"Abstract - The Labrador Trough contains world-class iron deposits which have been mined since 1954. The direct shipping of Knob Lake ores were mined at Schefferville from 1954 to 1982. Concentrate production began in 1961 in the southwest end of the Trough, with three mines currently producing concentrate and pellets at a rate of 35 Mt per year. West and north of Schefferville, several billion tonnes of taconite have been outlined in fine-grained, cherty magnetite iron formation. Several deposits of highly metamorphosed magnetite-specularite iron formation are located west of Ungava Bay. Numerous studies have shown that this medium- to fine-grained iron formation can be beneficated to 66% to 68% iron. In the area from Wabush Lake to Mont-Wright, a medium- to coarse-grained friable specularite-quartz iron formation is repeated by folding to form several large deposits. In this area, three mining operations are located with reserves and resources in the order of 5 billion tonnes.The iron deposits occur within iron formation in sediments in the extensive Proterozoic geosyncline called the Labrador Trough. Several facies of iron formation within the Sokoman Formation reflect variations in chemical composition and depositional conditions. The correlation between the mineralogy and textures is discussed to illustrate the development of different types of iron ores. This band extends for about 1100 km southeast of Ungava Bay through both Quebec and Labrador. Further south, it turns southwest past the Wabush and Mont-Wright areas to within 300 km of the St. Lawrence River. The iron formation is essentially folded and faulted along most of its length. The degree of metamorphism is variable, ranging from intense in the northern and southern portions to greenschist facies in the central portion.The stratigraphy, structure and mineralogy of the producing mines are described along with the history of discoveries. Geological input is required to achieve the strict specifications of the international iron ore market."

Jan 1, 2000

By Charles Tkaczuk

Key issues ? No business tool has greater potential to effect change and enhance profitability than process control. ? Successful businesses see process control as an integrated engineered system, designed and built into their business models from day one. ? The integration and use of process control sets the stage for years of compounded returns. ? Has been used for years to optimizing recoveries and minimizing waste. ? However, the mining/ore extraction sector has been slow to adopt integrated process control. What is the problem? ? Most executives and engineers do not clearly understand process control when applied to mining/extraction activities. ? Common approach has been to apply generic process control strategies as a blanket cure all and wait for it to pay off. ? No central focus which results in multiple group involvement, overlap and inconsistent application of questionable technology. ? Considered a low priority until production activities commence. ? Comfort in using brute force mining methods. ? An off-the-shelf integrated under ground mining process control architecture has not until recently been available.

May 1, 2004

By Siavash Zamiran, Abdolreza Osouli

"One of the most concerns of room and pillar mining system is subsidence of the ground surface due to coal mining particularly in room and pillar mines. Subsidence of ground surface is a result of floor, pillar, or roof failure of the mine. At the same, due to many difficulties associated with surface disposal facilities of coal refuse, some mining companies are trying to use underground space as a disposal storage place. In this study, stability and subsidence analyses of an underground coal mine located in the Illinois Basin are conducted. This room and pillar mine was abandoned and later on was used as a storage place to accommodate the coal fine refuse with slurry backfilling method. The geological stratigrophy and geomechanical properties of the mine floor and roof were collected. Floor and pillar stability analyses were conducted for areas with various extraction ratios. The stability of the mine was evaluated both prior and after slurry backfilling. The floor and pillar stability analyses results of the mine due to moisture exposure after slurry backfilling are discussed. The subsidence potential due to mine failure is also evaluated.INTRODUCTIONA typical lithology of coal seams in the Illinois Basin consists of weak underclay stratum. The immediate weak underclay causes frequent floor instability problems in Illinois underground coal mines. There are two different stages in assessing floor stability of the mines where slurry backfilling is planned. The first stage is during the mining operation when weak underclay layer squeezes under pillar stress and results in punching or bearing capacity failure. The second stage is after slurry backfilling. During this stage, the slurry material soaks non-durable floor layers and causes strength reduction in floor material. Pillar stability conditions should also be taken into account during both the operational period and after the slurry backfilling."

Jan 1, 2015

By Xuanxue Mo, Kaihui Yang, Steven D. Scott

Abstract -The Changning-Menglian metallogenic belt in western Yunnan, China, is characterized by the occurrences of both Pb-Zn-Cu and Cu massive sulfides in Permo-Carboniferous mafic volcanic sequences. These deposits were formed in a back-arc basin at a rifted continental margin in the Paleozoic Tethys Ocean. Pb-Zn-Cu deposits are associated with alkalic basalt, andesite, and lesser felsic volcanic rocks intercalated with limestone, which probably formed along an immature rifting segment on a continental basement. These volcanic rocks are enriched in K, Ti, LREE, and other incompatible elements, and have the attributes of alkalic within-plate basalt. An extensive unit of sulfide- carbonate-silica shale in proximity to massive sulfides contains high values of Mn, As, Mo, W, Sn, Sb, and Hg, and has REE patterns that are similar to the volcanic rocks. This, together with the graded bedding in the footwall volcanic rocks, suggests that the sulfides precipitated in a shallow, unstable, and carbonate-saturated volcanic basin. A stringer zone is traced downward for 500 m below the massive sulfide orebodies. It is characterized by an upper sericite-quartz zone and an extensive lower skarn alteration with enhanced W, Sn, and Bi. Lead isotope data show both continental basement and magmatic sources may have supplied the ore metals. Cu deposit and occurrences are hosted by tholeiitic units that represent the mature spreading segments in the back-arc basin. The tholeiitic lavas have LREE-depleted or flat REE patterns similar to MORB or back-arc mafic lavas. The cupriferous massive sulfides are overlain by an extensive unit of chlorite-magnetite or ochre, suggesting a relatively oxygenated oceanic basin. Ni and less Co mineralization is found in dolomite veins of the stringer zone. Enhanced concentrations of Ni, Co, Au, and As are found in the massive sulfides and in sulfide-rich tuffites. The geological setting and mineralization of the Changning-Menglian belt has similarities with modern back-arc basins such as the Manus Basin in the western Pacific.

Jan 1, 1999

By R. Heikkilä

Fluent information exchange between different work phases, software and systems used in infra construction is a key for successful execution of infra construction projects. Open and publicly available information formats with the determined data models aim to facilitate the interoperability between different software and systems developed by competitive vendors. While building and construction industry has developed and used IFC format for years, infrastructure sector has just recently started to target clear efforts on the development of open information formats for infra construction processes. In the paper, a new Inframodel3 extension just developed in Finland and based on the LandXML1.2 international standard is to be introduced. The aim of the Inframodel3 was set to meet the requirements of information transfer needed especially between BIM based design software, measurement systems and 3-D machine control systems used in road, railway and watercourse construction projects. Some test results are reported and evaluated in the paper. In the field of bridge engineering, the IFC format and IFC Bridge extension have been tested and evaluated in Finland. The results from the experiments show and verify as well the applicability of these open formats to the information exchange requirements in bridge engineering. The current limits for open information transfer of these formats are shown. The active co-operation with the International Building SMART Organization has led to the achieved status and position for both the Inframodel3 and IFC Bridge formats and hence the continuing international support provided by Building SMART.

Aug 1, 2013

Presentation Overview ?WRDC Purpose and Activities ?Women in Trades, Technology and Operations (TTO) Occupations ?Factors in Successful Recruitment / Retention of women (VBNC) ?Recruitment and Retention Strategies ?Conclusion Women in Resource Development Committee (WRDC) ?Incorporated in 1999 as a Not for Profit Organization ?Based in Newfoundland and Labrador ?Works to Increase the Participation of Women in Natural Resource Industries ?Research (Using Gender-Based Analysis) ?Career Exploration Programs for Women and Girls ?Outreach and Advocacy ?Policy Development ?Public Awareness and Education ?Gender Sensitivity Training ?WRDC Educational Resource Centre

May 1, 2006