Search Documents

By Eugene Larochelle

The serpentine of the Eastern Townships of Quebec is more or less seamed and impregnated with chrysotile asbestos, of which we note two types: the cross-fibre and the disseminated fibre. The cross-fibre type always appears in fibres or crystals arranged parallel to one another, and disposed at right angles to the walls of the matrix serpentine. The length of fibre of these veins, which run in every conceivable direction, even crossing ?one another, varies from microscopie dimensions to three and sometimes four and even five inches. It is the principal form of asbestos found in the serpentine of Thetford Mines, Black Lake, Coleraine, and Asbestos. The disseminated-fibre type, which is the main product of the serpentine of Broughton township, in which ate located the mines at East Broughton, does not form veins, but occurs in the serpentine without any definite arrangement. There is a difference in the toughness and hardness of the rock of the two types, the Broughton serpentine being softer than that at Thetford. The disseminated-fibre section of the serpentine belt is probably more regular in its content than is the cross-fibre section. Nevertheless, it contains no 'crude,' which is the most valuable of asbestos, and the fibre is usually shorter than the cross-fibre average.

Jan 1, 1928

By H. A. Pearse

Introduction This paper may be regarded as another instalment of the story of the Britannia milling operation. From time to time in the past, articles (1) have been prepared by various members of the staff, giving details of crushing, grinding, and flotation treatment for the normal Britannia ore. It is not, therefore, the purpose of the present paper further to discuss what may be termed the standard milling operation, but rather to describe a flotation practice which has been evolved directly as a result of the general depression. The normal Britannia ore mixture contains chalcopyrite and pyrite as the main sulphide minerals, together with minor gold and silver values. The standard milling practice, evolved during several years of experimentation, provided for bulk flotation of the two sulphides after primary grinding to only approximately 35-mesh, followed by regrinding of the bulk concentrate, with subsequent separation of the chalcopyrite and pyrite to make a marketable concentrate of each mineral. However, in the face of a constantly increasing surplus of copper on the world markets and a steadily falling price during 1930 and 1931, it was obviously undesirable to continue producing large quantities of this metal at a loss. On the other hand, Company officials were very reluctant to add to unemployment by closing down entirely, provided operations could be continued without excessive losses. Fortunately, the existence was known of a fair sized body of ore, quite low in copper and relatively high in zinc content, with also a very considerably higher gold value than that prevailing in other sections of the mine.

Jan 1, 1934

By Zhang. L.

Ordered intermetallic PtSb had been synthesized by arc-melted and then sintering treatment. The electro-oxidation of formic acid on PtSb was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results are compared to those at a polycrystalline platinum electrode surface. It was found that PtSb intermetallic was catalytically more active than pure platinum according to the onset potential and current density. XRD and XPS technologies had been used to investigate the crystal structure and electron effect. We think formic acid decomposition on PtSb favors the reactive intermediate route and is not very much affected by the CO intermediate as compared to Pt.

Jan 1, 2005

By S. Bantubani, I. Mc Dougall, S. Arjun, H. Joubert, R. Hansraj

The requirements determining the design of the Söderberg electrode columns used in base metal applications are different to those of other industries. There is a strong trend to position the contact shoes above the furnace roof in order to reduce the risk of water leakages directly onto the furnace bath. Tenova Pyromet has adapted its proven electrode column design for application on base metal electric furnaces based on these requirements. The design modifications implemented as well as considerations regarding the overall electrode-roof-furnace arrangement are discussed. Equally important is the management of the Söderberg electrodes to prevent over or under baking. Tenova Pyromet has developed the AutoFurn™ furnace controller to not only optimise furnace operations, but to improve electrode management. An overview of the electrode management control philosophy implemented by AutoFurn™ is provided, focusing on intelligent electrode regulation, slipping and baking. INTRODUCTION Tenova Pyromet has developed an electrode system for use in base metal furnaces, which builds on the experience that Tenova has gained during the past 30 years with electrodes in the ferroalloy and base metals industries. In base metals applications, an important safety consideration is the minimization of water within the furnace and on the furnace roof. In addition, direct contact between copper equipment such as contact shoes and pressure rings and the contents of the furnace is discouraged. In a 3 phase AC furnace, three electrode columns transfer the electrical energy to the furnace bath. Both Söderberg and prebaked carbon or UHP graphite electrodes are in use in base metal furnaces. In each column, the electrode is held in position by a hydraulic slipping and regulating device, a pressure ring and contact shoes. The electrodes can operate in a submerged-arc or brush-arc configuration, where the electrode is immersed in the slag or a short distance above the slag (Mc Dougall 2013). The electrode equipment is divided into an upper and a lower electrode assembly. The self-baking Söderberg electrode is made from lengths of steel casings that are added to the top of the electrode column and welded into place. Carbon electrode paste is added to the inside of these casings and is baked to form a solid tip in the region of the contact shoes. The working platform that surrounds the area where new electrode casings are added, is electrically isolated from the building and each electrode is isolated from the others to ensure the safety of the personnel who perform the electrode casing additions.

Jan 1, 2019

By W. R. Tyson

Imperfections such as lack-of-fusion and undercut are inevitable in field welding of pipelines. Above a certain size, such defects must be removed or repaired. In the present state of the art, determination of allowable defect size is done by Engineering Critical Assessment (ECA). This requires measurement of toughness, and comparison of toughness with crack driving force. ECA methods used in current international pipeline standards will be reviewed and compared.

Jan 1, 2010

By Greg M. Hollyer

The search for minerals in the future will be dominated by deeper exploration and the need to accurately target ?blind? deposits as more and more of the ?easy? near surface targets are exhausted. In this context, key technologies are emerging for deep exploration both in grassroots and minesite exploration, including the Titan 24 Deep Penetrating geophysical technology. Introduced in 2001, this technology has grown rapidly into an accepted approach for exploration in a variety of geologic environments, including brownfield environments where discovering additional reserves would most quickly benefit companies. Titan 24 belongs to a new class of sophisticated Distributed Acquisition Systems (DAS) which record high-volume, high-quality data simultaneously at multiple receiver stations. This data is then processed digitally, modeled using specialized inverse modeling software, and interpreted according to geologic and other parameters. The result is a robust, high-quality, high-volume data sets which provide a basis for improved imaging to depth. In this paper, the Titan 24 distributed technology is discussed. Illustrations of the vast improvement to overall exploration are showcased through results in several case studies. These include examples from two gold deposits, a porphyry deposit and a minesite. These examples show the range of applicability of the technology and the ability to effectively image mineralization, lithology, structure and alteration to depth as an aid to understanding prospective mineral deposits and targeting drills more accurately.

May 1, 2008

By Brian O'Hearn, Doug Hanson

"The most commonly used tendon supports in the Sudbury area include rock bolts, rebars, friction anchors and cable bolts. Due to the fact that these tendons are physically different and employ different anchoring systems they offer varying degrees of stiffness, yield ability, load capacity, anchor dependability and energy absorption. These differences coupled with variable rock mass and changing stress conditions have made it challenging to engineer the design of an effective support system. By tapping into the knowledge and experience gained by ground control practitioners, an empirically based rating system has been assembled that offers a guide to designers of support systems when choosing the most effective tendon support over a range of rock mass and stress conditions.A methodology referred to as support planning can be used to design support systems whose rehabilitation costs will be minimized. The use of multiple tendon types in anyone support layout is advocated, particularly when the stress state of the rock mass to be supported is expected to undergo a change."

Jan 1, 1995

By É. Poulin, J. Bouchard, E. M. Pérez-García

Process control and optimization have always been crucial aspects in the mineral processing industry, and expectations constantly increase to cope with more stringent security, quality, efficiency, and environmental performances. The main challenges to reduce variability of key process variables, and steer profits to higher values while maintaining sustainability indexes within acceptable ranges come from nonlinear responses and circulating loads. The most commonly implemented control strategies rely on simple PID controllers for practical implementation and maintenance considerations. If arguably good performances are accomplished when these are adequately set up, there is also room for further gains by using more advanced methods such as model-based techniques. There is thus a need for more realistic process and equipment models. Based on advances of the past few decades, this paper introduces an autogenous/semi-autogenous mill (AG/SAG) model to be included in a modular comminution circuit simulation toolbox comprising ball/rod mills, material handling, and classification devices. The proposed mill model incorporates a modified version of the classic comminution equation that makes grinding rates proportional to the energy input. It requires the determination of a selection function (fragmentation rates) and a breaking function (fragments distribution). The former is modelled with an S-shaped curve characteristic of AG/SAG processes and the latter is a size-relative distribution of the produced fragments. The power draw is predicted employing the empirical equation of Austin. The paper also develops a case study to illustrate how the proposed simulation framework can capture the behaviour of an actual plant. Model calibration consists in an optimization problem that search the global minimum of the difference between predicted and measured/estimated size distributions, power draw, solid fractions, etc. Results demonstrate that the mill simulator can mimic an actual process in its operation conditions. INTRODUCTION Comminution is a key stage in the mineral processing industry, obviously because the phases of interest must be liberated to be able to recover them. In general terms, the global performance of a plant depends largely on the efficiency of the grinding circuit and on the material properties such as its grindability, density, and mineral grades. The subject has vastly been studied since as early as the 19th century, when Rittinger (1867) and Kick (1883) developed some of the first empirical models to relate grinding and energy input. The great interest in the subject comes from the fact that this operation is costly and, probably most concerning, highly inefficient. Buckingham et al. (2011) estimated that ore comminution can represent up to 60% of the overall plant power draw. Moreover, only a modest fraction of the power draw effectively translates into rock fragmentation. For grinding, estimates range between 1% and 25%, depending on the reference used, while the rest is mainly lost as heath (Fuerstenau & Abouzeid, 2002; Tromans & Meech, 2002; Bouchard et al., 2017).

Jan 1, 2019

By V. Bonilla-Sierra, M. Elmouttie, L. Scholtès, F. V. Donzé

In the presence of joint sets sub-parallel to a slope face, the stability of the rock mass is controlled by the shear strength of the joints. On one hand, if the joints are persistent their shear strength can be assessed according to Mohr-Coulomb criterion, assuming appropriate values for the cohesion and the friction angle on the joint surface. On the other hand, if the joints are non-persistent with their continuity being interrupted by the presence of rock bridges, their shear strength will increase considerably. In this latter case, the contribution of the rock bridges to the shear strength of the joint has to be accounted for in order to better assess the stability of the rock mass. A numerical analysis of the progressive failure of a rock slope involving a non-persistent joint has been set up based upon simulations performed using a Discrete Element Method (DEM) algorithm specifically enhanced for the modeling of jointed rock masses. Pre-existing discontinuities are explicitly accounted for in the model by using a modified contact logic that ensures an explicit and constitutive mechanical behavior of the joint planes. In addition, rock bridges can be spatially distributed along these joint planes following a prescribed probabilistic technique. Jennings’ formulation (Jennings, 1970) is considered as one of the first rock slope analysis that evaluates the shear resistance to sliding as a weighted combination of the shear resistance of the intact rock and the joint planes. The validity of this formulation is discussed in the present study. Contrary to the Jennings’ formulation, we show that tensile failure is an important mechanism, particularly as the dip angle of the sliding plane increases.

Jan 1, 2015

By Tatyana Alexandrova

The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Technological aspects of processing precious metal ores are examined in two respects: enhancing gold recovery from double refractory ores; and using carbonaceous ores on a production scale. The dispersed carbonaceous matter (DCM) present in concentrates causes the adsorption of [Au(CN)2]- complex on their surface during cyanidation process. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The possibility of rare metals recovery, including rhenium, from black-shale rocks, has been examined. Comparative assessment of analytical methods of rare metals detecting has been carried out. It has been proved that neutron activation analysis is a promising technique. It has been shown that colloid-salt fraction (nanofraction) with particle size less than 1000 nm makes up to 3 wt% of black shale samples and is extracted by water under special conditions. The use of water instead of chemically active reagents provides insolubility of the mineral matrix and fully reflects the colloid-salt element of the samples. To sum up, the justification of the choice of technology for processing of carbon-bearing ores is based on examining the type of carbonaceous matter and its adsorption behavior. When the content of carbon of high degree of metamorphism is considerable, it is possible to recover platinum group elements and rare elements from this type of ores. The obtained results predetermine the general guidelines for creating new methods and techniques of processing carbonaceous material for integral development of solid minerals in the mining and oilfield areas of Russia.

Jan 1, 2016

By K Komori

Naoshima Smelter and Refinery has treated shredder residue and incinerator fly ash in Japan since 2003. As a highlight, a new incinerating and melting furnace, as well as fly ash washing treatment plant were newly constructed for pre-treatment of shredder residue and fly ash respectively, and the pre-treated materials are ultimately treated in the existing Mitsubishi continuous copper smelting and converting process line. Since wastes such as shredder residue tend to vary in size and in shape, and contain some chlorine, the installation of a new pre-treatment line was required. The combination of the new pre-treatment line with the existing Mitsubishi Continuous Copper Process line has created a highly efficient and environmentally friendly system for recovering and recycling of valuable metals that previously used to be sent to a landfill. This paper reviews the approach that Naoshima took to establish its current recycling business strategy.

Jan 1, 2007

By P. Taskinen, A. Jokilaakso

The Flash Smelting Process for copper and nickel production has been one of the most successful new metallurgical process developments in the 20th century. The experimental data from laboratory scale investigations of studies has produced information and insight into the reaction mechanisms and kinetics of the flash reactions of copper concentrates. Advanced computer models coupling chemical reactions with a Computational Fluid Dynamics (CFD) software became possible with the development of commercial CFD software together with increased computing power. Currently, there are both experimental and CFD modelling, including also CFD–DEM coupling (Discrete Element Method), studies ongoing for investigating the kinetics of matte – slag reactions in the flash smelting furnace (FSF) settler. The ultimate goal of the modelling work is to develop a comprehensive FSF model for studying the behavior of changing raw materials, both primary and secondary, and distribution of their elements between the matte, slag, and gas phases. The use of User-Defined-Functions (UDF) is one way to digitalize metallurgical knowledge and experimental information to be used for supporting process experts and development of artificial intelligence applications in metallurgy. In this paper, a review of the development of the FSF reaction shaft modelling and experimental investigations, and the current work for the settler reactions’ experiments and modelling are presented. INTRODUCTION The Outotec Flash Smelting process (Bryk, Ryselin, Honkasalo, & Malmström 1958) has been used in the copper and nickel industry for 70 years with continuous support from experimental investigations by many research groups in academia, among others Jorgensen and Segnit (1977); Jokilaakso, Suominen, Taskinen and Lilius (1991), Chaubal and Sohn (1986), Kim and Themelis (1986), and in industry Mäkinen and Jåfs (1982); Kojo, Lahtinen and Miettinen (2009); Tuominen, Pienimäki and Fagerlund (2016). It has been developed also for pyrite and lead smelting (Asteljoki, Sulanto & Talonen, 1984). A schematic illustration of the FSF and other main parts of the process is depicted in Figure 1. Also, two and three dimensional physical water or gas models have extensively been used in product and process development (Lilja & Rajainmäki 1995). During the recent decades, computer based models have increasingly been adopted in the FSF research and development (Ahokainen & Jokilaakso, 1998); Ahokainen, Jokilaakso, Taskinen & Kytö, 2006; Hahn & Sohn, 1990; Jorgensen & Elliot, 1992; Zhou, Zhou, Chen & Mao, 2014; White, Haywood, Ranasinghe & Chen, 2015) to name a few, but also in supporting engineering and sales of the technology (Miettinen 2017). Even though the reactions of the sulfidic concentrate particles have been included in the reaction shaft modelling, the complete FSF model with both gas-solid/drop and molten slag/matte drop has so far been and still is too demanding for today’s computer hardware.

Jan 1, 2019

By Masatsugu Morimitsu

This paper introduces new technology of oxygen evolution anodes which can be applied to produce copper, zinc, cobalt, and other metals by electrowinning. The anode consists of nano iridium oxide particles dispersed in amorphous tantalum oxide matrix as a catalytic layer formed on a titanium substrate. The anode can reduce oxygen evolution potential by 0.25 to 0.55 V compared to commercially available lead alloy anodes and can suppress unwanted side reactions such as manganese oxyhydroxide, lead oxide, cobalt oxyhydroxide which occur during oxygen evolution in the electrowinning solutions. This technology is effective for environmentally friendly electrowinning processes with low energy consumption and less anodic deposition.

Jan 1, 2011

By J. H. Rickard, D. H. Watkinson

"Abstract - Detailed petrographic and quantitative (electron microprobe, SEM-EDS) mineralchemical analyses of sulfide ore from the 100 orebody at the Copper Cliff North mine, Copper Cliff, Ontario, reveal numerous stages of ore development. Sharp contacts between weakly mineralized quartz diorite and blebby to massive sulfides indicate multiple intrusive events within the Copper Cliff offset dike. A spatial association of sulfides and hydrous minerals, such as amphibole, biotite, chlorite and epidote, suggests that most primary ore has been affected by later hydrothermal fluids. Sulfides are often enclosed or bordered by these secondary silicate phases. The ore consists primarily of pyrrhotite, pentlandite, chalcopyrite, with trace michenerite, cobaltite/gersdorffite, irarsite, hessite, tsumoite, and bismuth tellurides.Geological and petrological comparison of the 100 orebody and the adjacent 900 and 890 orebodies has revealed distinct similarities in ore distribution. Data show that the 100 orebody is depleted in platinum-group elements (PGE) relative to the 900 orebody. Platinum-group elements from the 100 orebody may have been hydrothermally remobilized and partly emplaced in the 900 orebody, in adjacent veins, or in magmatic breccia. Analysis of Cu, Ni, and PGE assay data of ore samples has characterized their distribution among the eight different ore textures in the orebody. There is a strong association between Pt and interstitial sulfide, and to a lesser extent massive sulfide, but little correlation between chalcopyrite-rich ore and PGE in the 100 orebody, unlike many other deposits in the Sudbury region."

Jan 1, 2001

By Lucas van Latum

A Model for Safety Swiss cheese metaphor of safety layers Image »Multiple layers with independent, often transient failure modes »For a loss to occur, all layers must fail independently and simultaneously ??Latent? failures are due to inherent system flaws ??Active? failures are due to unsafe acts

May 1, 2011

By P. R. Brito-Parada, G. Bhutani

"The physical processes occurring in flotation columns are very complex as they take place at different scales over a range of sizes and multiple phases. Column design and optimum operating parameters are usually obtained from empirical studies and although progress has been made on its numerical modelling, most column models rely on simplifications that do not fully capture the hydrodynamics. In particular, Computational Fluid Dynamics (CFD) models of the pulp phase in flotation usually assume the bubble population to be monodispersed. While this assumption may be reasonable in some situations, the polydispersed nature of the gas phase can have a significant impact on the predicted flotation rates.Techniques to model size distribution do exist in the literature and have been rigorously analysed in the past two decades for bubble columns, which are very similar to flotation columns from a hydrodynamics point of view. In fact, available CFD models of flotation columns are an extension of bubble column models, sometimes including additional equations for solids treated as passive scalars. This work focuses on the development of an efficient CFD model for flotation columns. The bubble size distribution in the column has been modelled using the Population Balance Equation (PBE), which is solved using the Direct Quadrature Method of Moments (DQMOM). Coupled with the PBE, the multiphase flow equations in the column have been modelled using the standard Eulerian–Eulerian approach. The solution of this coupled system has been made tractable in this work with the implementation of a highly parallelised adaptive-mesh finite element method. This powerful framework has been implemented in the open source CFD code Fluidity and it allows the carrying out of detailed simulations of flotation columns in 2D and 3D, with important implications for industrial column evaluation and design."

Jan 1, 2016

By Guoxiang Chi

Hydrocarbon fluid inclusions entrapped in diagenetic minerals may be used to constrain hydrocarbon exploration models in two aspects. First, the distribution of different types of hydrocarbon inclusions in different tectonostratigraphic domains, and their relationships with organic matter maturation levels may reflect a regionalscale variation in the thermal regimes of the hydrocarbon systems. Second, the relative timing of hydrocarbon inclusions in the diagenetic history may provide constraints on the evaluation of reservoir potential. This paper summarizes the distribution of hydrocarbon inclusions in four different Paleozoic tectonostratigraphic domains in eastern Canada, discusses its implications on hydrocarbon systems in the different domains, and finally provides two examples to show how the relative timing of hydrocarbon inclusions may be used in the evaluation of reservoir potential. Oil inclusions mainly occur in host rocks that are within the oil zone, although some are found in units in the condensate zone. Light hydrocarbon inclusions occur in the dry gas zone, and methane inclusions were found from dry gas zone to anchimetamorphism zone. This correlation between hydrocarbon inclusions and host rock maturation implies that the hydrocarbons were derived from source rocks having a maturation level broadly similar to the host rocks. Although the Paleozoic rocks are generally relatively poor in reservoir quality, the two examples provided in this paper show that in some stratigraphic units, significant secondary porosities could have existed prior to some hydrocarbon migration events, thus favoring the accumulation of hydrocarbons.

May 1, 2001

By Ting An Zhang, Chengzhi Jiang, Xiujing Zhai, Feng Xie

The extraction and concentration of nickel from aqueous solutions by emulsion liquid membranes (ELMs) using tributylphosphate (TBP) as extractant has been investigated in this research. The emulsion liquid membrane consists of a diluent (kerosene), a surfactant (Span 80), a mobile carrier (TBP), and a stripping solution (ammonia solutions). Important factors influencing the separation process including membrane composition, feed composition, and mixing speed have been examined. The results show that more than 90% of nickel in the feed solution could be extracted by ELMs under the experimental conditions, indicating the feasibility to use the designated ELMs to detoxify nickel-containing industrial waste solutions.

Jan 1, 2014

By S. Maleksaeedi

On-site evaluation of strength using hardness is common for different materials. The lack of such relation for aluminum alloys has always been felt. In this work, a finite element analysis of plastic deformation and its distribution in Brinell hardness testing is presented. The analysis has been performed for different strength levels of aluminum alloys. By utilizing the Von Mises equivalent strain in hardness, it is tried to derive a correlation between hardness and strength values for the alloys under consideration. The derived correlation is verified using the experimental values available in literature.

Jan 1, 2004

By W. T. Irvine

"The H.B. Mine, a zinc-lead operation of the Consolidated Mining and Smelting Company of Canada Limited (Cominco), is in south central British Columbia, on Sheep Creek, a west-flowing branch of the Salmon River. It is 3 miles by road from B.C. highway No. 6, 30 miles south of Nelson, B.C., with an excellent highway connection to the smelter city of Trail, 35 miles from the mine. The nearest permanent settlement is the village of Salmo, 7 miles distant by road. The mine is situated along a belt containing other important zinc-lead deposits, including those of the Canadian Exploration Company, 3 miles to the south, and the Reeves MacDonald mine, 9 miles distant again to the southwest.Deeply oxidized outcrops were located in 1907 on the north side of Sheep Creek valley by two prospectors named Horton and Benson. The property was given the name H.B., after the two discoverers, and there commenced a long and intermittent series of mining operations designed mainly to develop and extract oxidized lead-zinc ore. In 1925 a determined attempt was made by a British syndicate to develop a large tonnage of sulphide ore, but this ended in failure after some 3,000 feet of lateral development had been done. In 1927 Cominco acquired the mine, but it lay idle until 1946 when a geological study was followed by a program of surface drilling which encountered extensive sulphide mineralization. An underground development program revealed more details of the deposit, and sufficient ore was found to warrant construction of a 1,000-ton mill. Mine preparation and mill construction were completed by early 1953, but production was deferred due to low metal prices. The mine was finally brought into production early in 1955."

Jan 1, 1949